To install the Phoenix Card Manager Plus Versions less than 3.00, insert the diskette, run INSTALL and then answer the questions on screen as indicated below:
1. Type the number 1 or 2 to indicate the number of sockets. 2. Type either Q or A to indicate Quick or Advanced Installation. 3. Indicate the directory and destination drive where Card
Manager Plus will be located.
4. If you chose Quick Installation, answer the on-screen questions as indicated:
Beep On Card Insertion and Removal ? Y Flash Memory Card ? N
Windows ? Y
ATA Drives in PCMCIA Socket(s) ? Y
5. If you chose Advanced Installation, answer the on-screen questions as indicated:
Com Port: 4 ATA Drive: Y PCMCIA IRQ: 10 ATA Windows Addr: C900 CIS Window Addr: C800 Use Flash File System: N Card Settle time: 660 ms Windows 3.1: Y Beep on Card Detect: Y
DEVICE = C:\DOS\HIMEM.SYS
DEVICE = C:\DOS\EMM386.EXE NOEMS X = C800-C8FF X=C900- CCFF
DEVICE = C:\PCMPLUS\PCMSS.EXE
DEVICE = C:\PCMPLUS\PCMCS.EXE/WAIT=12/ADDR=C8 /IRQ= 10 Note that /IRQ=10 can also be /IRQ=11 or /IRQ=15. 8. The following command statement may also exist and needs
to be enabled by removing the letters “REM” if they appear at the beginning of the command statement.
DEVICE=C:\PCMPLUS\PCMRMAN.EXE
9. One of the following command statements should be enabled, by removing REM from the beginning, depending on whether one or two PCMCIA slots were indicated at the beginning of the installation procedure. The command statement including
/1 indicates one slot. The command statement including /1 / 2 indicates two slots. Modify these command statements if necessary.
DEVICE=C:\PCMPLUS\PCMATA.SYS /1 /ADDR=C9 DEVICE=C:\PCMPLUS\PCMATA.SYS /1 /2 /ADDR=C9 Phoenix Card Manager Plus Version 3.00
To install the Phoenix Card Manager Plus Version 3.00, insert the diskette, run INSTALL and then answer the questions on screen as indicated below:
1. Type either Q or A to indicate Quick or Advanced Installa- tion.
2. If you chose Quick Installation, answer the on-screen questions as indicated:
Number of Sockets: 1 or 2
Using PCMCIA Cards under windows 3.1: Y Flash File System Support: N
PCMCIA Modem/Fax Card Support: N ATA Card Support: Y
3. If you chose Advanced Installation, answer the on-screen questions as indicated:
Number of Sockets: 1 or 2
Complete pathname for Windows 3.1: C:\WINDOWS IRQ....(ms): 15
CIS Windows Address (C000H-EF00H): C800 Token Ring Speed: 4
Card Settle Time...(ms): 660 Flash File System Support: N PCMCIA Modem/Fax Card Support: N ATA Card Support: Y
ATA Windows Address: C900 ATA Drive Spin Down Time: 5 ATA Support for Socket #0: Y Number of partitions on ATA: 1
4. Continue pressing [enter] until the screen displays Modify CONFIG.SYS EMM386.EXE option? Type Y to indicate yes. 5. Ensure that the following command statements appear
exactly as shown below. Modify the command statements as necessary.
DEVICE = C:\DOS\HIMEM.SYS
DEVICE = C:\DOS\EMM386.EXE NOEMS X=C800-C8FF X=C900=CCFF
DEVICE=C: \PCM3\CNFIGNAM.EXE /DEFAULT DEVICE=C: \PCM3\PCMSS.EXE
DEVICE=C: \PCM3\PCMCS.EXE DEVICE=C: \PCM3\PCMRMAN.EXE DEVICE=C: \PCM3\PCMATA.SYS
pcmata= /ADDR=C9 /SD=5 /S0=1 /SRAM UseCards= SetupMode=1 ATAWindowBase=c900 ATASpinDowntime=5 ATANoOfPartitions=1 IRQ=10 CISWindowBase=c800 TokenRingSpeed=4 CardSettleTime=669 [DEFAULT.Resources] include_mem=0xc8-0xc8, 0xc9-0xcc exclude_mem=0xD0-0xDF include_io= exclude_io= include_irq= exclude_irq=
Note: In command statement six, /S0=1 can also be /S0=1 /S1=1 to indicate that there are two PCMCIA slots. SystemSoft PCMCIA Driver Installation - CardSoft 3.1 Install Utility Version 2.14
1. Type INSTALL and press [ENTER].
2. Use the arrow keys to select First Time Installation. 3. Use the arrow keys to select Standard Installation. 4. Answer the following on-screen questions as
indicated below: Number of Sockets: 1 Destination Drive: C:
Directory Pathname: \CARDSOFT Confirm Destination Drive and Directory: Y Create/Modify CONFIG.SYS? Y
5. If CardSoft is installed properly, your screen will show the command statements below. Manually edit the command statements as needed or start the installation procedure over. DEVICE=C:\DOS\HIMEM.SYS
DEVICE=C:\DOS\EMM386.EXE NOEMS X=D000-DFFF DEVICE=C:\CARDSOFT\SSVADEM.EXE DEVICE=C:\CARDSOFT\CS.EXE DEVICE=C:\CARDSOFT\CSALLOC.EXE C:\CARDSOFT\CSALLOC.INI DEVICE=C:\CARDSOFT\ATADRV.EXE DEVICE=C:\CARDSOFT\CARDID.EXE C:\CARDSOFT\CARDID.INI Note that SSVADEM.EXE in the third command statement is the name of the Socket Services driver. It can be either SSVADEM.EXE, SS365SL.EXE, SSCIRRUS.EXE or SSDBOOK.EXE.
Award PCMCIA Driver Installation - Cardware Version 1.18B 1. Type INSTALL and press [ENTER].
2. Specify the drive that will store the Cardware System files. 3. Specify the directory where the Cardware System files will
be located. The default directory is C:\CARDWARE. 4. Select your platform name from the list of platforms. 5. Select the PCMCIA controller from the list displayed. 6. Type Y to install Cardware on drive C and then type Y to
choose Express Installation.
7. If Cardware is installed properly, the command statements below will be in your CONFIG.SYS file. Edit the command statements as needed or start the installation procedure over. DEVICE=C:\DOS\HIMEM.SYS
DEVICE=C:\DOS\EMM386.EXE NOEMS X=CF00-D000 X=D000-E000 DEVICE=C:\CARDWARE\PCSS.EXE