Service Switching
SSFSRF ESS
3.19 Appendix. IN Service Trigger Table
SSF IN SERVICE TRIGGER DATA
DATA PRINTED FROM THE [NON] OPERATING AREA
IST
| | ||
| |bcap evtype cge ext6 ext7 ext8 ||
| | ||
| |pi dl sfc scfr ||
3 DP9 or DP17 armed on
ariinf AssistRequestInstruction INFormation Indicates how to fetch the CorrelationID
2 Included if available
botr B-Number origin transferring This indicator determines whether the B-number origin should be transferred from the incoming side to the outgoing side.
0 No transferring allowed 1 Transferring allowed
bsi Backward setup indicator
During setup of an IN service, the BSI informs the incoming side about setup conditions.
0 No backward setup indicators used
1 Malicious call tracing if no calling party number is available
cc Charging case
This is the charging case default value which can be transferred to the outgoing side.
0 - 4095 Charging case
NO Charging case not used
ccbsind Call completion on busy subscriber indicator This parameter indicates how to handle the CCBS service when the CCBS interacts with an IN service in the call too.
0 Unconditional suppression of CCBS
1 Conditional acceptance of CCBS CCBS is accepted if the incoming call to the SSF originates in the same exchange as the SSF
cdn Called party number
This parameter determines whether the called party number should be
included when the SCF is invoked.
0 Not included 1 Included
2 Included if available cess SCF control essential
calls in a stable phase are allowed to survive abnormal loss of the dialogue to the SCF.
0 Calls are not allowed to survive
1 Calls are allowed to survive
cgc Call gap criteria
0 No call gap criteria 1 Called address value 2 Gap on service
3 Called address and service 4 Calling address and service
cgcat Calling party category
This parameter determines whether the calling party category should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
cge Call gap encountered
This parameter determines whether the call gap encountered should be included
when the SCF is invoked.
0 Not included 1 Included
2 Included if available
chindic Charging indicator
Default setting of charge no charge indicator in the ISUP message ANM This indicator must be applied in case the call is handled by basic routing.
0 No indication 1 No charge 2 Charge
chztr Charging zone transferring
1 Continue without SCF
2 White TCAP, Blue SCCP 3 White TCAP, White SCCP
evtype Event type BCSM
This parameter determines whether event type BCSM should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
exid Exchange identity
This parameter determines whether exchange identity should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
ext1 Extension 1
This parameter determines whether extension 1 should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
ext2 Extension 2
This parameter determines whether extension 2 should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
ext3 Extension 3
This parameter determines whether extension 3 should be included when the SCF is invoked.
0 Not included 1 Included
ext4 Extension 4
This parameter determines whether extension 4 should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
ext5 Extension 5
This parameter determines whether extension 5 should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
ext6 Extension 6
This parameter determines whether extension 6 should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
ext7 Extension 7
This parameter determines whether extension 7 should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
ext8 Extension 8
This parameter determines whether extension 8 should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available ext9 Extension 9
This parameter determines whether
extension 9 should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
ext10 Extension 10
This parameter determines whether extension 10 should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
ext11 Extension 11
This parameter determines whether extension 11 should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
ext12 Extension 12
This parameter determines whether extension 12 should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
ext13 Extension 13
This parameter determines whether extension 13 should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
ext14 Extension 14
This parameter determines whether extension 14 should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
ext15 Extension 15
This parameter determines whether extension 15 should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
ext16 Extension 16
This parameter determines whether extension 16 should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
fdestid1 Format of SCF address
This format parameter is used in case the SI (sending information) parameter from the routing case specification is set to 0, or no SI parameter is given.
0 Local
1 Destination point code and subsystem number 2 Global title
3 Global title
and subsystem number
4 Global title service number
5 Global title service number and subsystem number
6 SCFid as global title
7 SCFid as global title and subsystem number
fdestid2 Format of SCF address
This format parameter is used in case the SI parameter from the routing case specification is different from 0.
0 Local
1 Destination point code and subsystem number 2 Global title
3 Global title
and subsystem number
4 Global title service number
5 Global title service number and subsystem number
6 SCFid as global title
7 SCFid as global title and subsystem number
fwci Forward call indicators
This parameter determines whether the forward call indicators should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
fwindic Forwarding indicator
This is an indicator used to specify whether the call on the outgoing leg should look like a forwarded call or not.
0 No forwarding 1 Forwarding
gdbcgid Business communication group ID
This parameter determines whether the business communication group ID
should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
gdpntc Private network travelling class mark This parameter determines whether the private network travelling class mark should be included when the SCF is
0 Not included 1 Included
2 Included if available
gnacdn Additional called number
This parameter determines whether the additional called number should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
gnacon Additional connected number
This parameter determines whether the additional connected number should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
gnacpn Additional calling party number
This parameter determines whether the additional calling party number
should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
gnaorcdn Additional original called number This parameter determines whether the additional original called number should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
gnardn Additional redirecting number
This parameter determines whether the additional redirecting number
should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
gncdfn Called freephone number
This parameter determines whether the called freephone number should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
gtmod Global title service number modification Digits can be deleted, and a prefix can be added to the service number used as global title.
gtnapi Global title number plan 0 Reserved
1 ISDN/Telephony (E.164) 2 Data (X.121)
3-15 Spare
NO Parameter is no longer valid
gtnt Global title nature of address
Used in case format of SCF address is global title logical, SCFid, or global title service number.
0 Reserved
1 International Number 2 Unknown
3 Subscriber number
4 National Significant Number 5-10 Spare, standard use
11-15 Spare, standard use NO Parameter is no longer valid
gttran Translation type for global title This parameter is used in case format of SCF address is global title, SCFid, or global title service number.
0-254 Translation types 255 Reserved
hlc High layer compatibility
This parameter determines whether the high layer compatibility should be included when the SCF is invoked.
0 Included 1 Not included
2 Included if available
impaind Implied A-number indicator
This is an indicator used to specify whether the implied A-number shall be used in basic routing when no SCF or SSF provided A-number exists.
0 Do not use implied A-number 1 Use implied A-number
ipav IPAvailable
This parameter determines whether the IPAvailable should be included when the SCF is invoked.
0 Included 1 Not included
2 Included if available
ipcap IP SSP capabilities
This parameter determines whether the IP SSP capabilities should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
ist IN service trigger
Current maximum value is defined by SAE 701.
lansel Language selection
This parameter determines whether the
language selection should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
ln Location number
This parameter determines whether the location number should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available
mpindic Meter pulse indicator
This parameter indicates whether meter pulses should be transferred from the outgoing side to the incoming side.
0 Pass 1 Drop numdig Number of digits
0 Not relevant for TDP
1-28 Number of called party digits to collect for TDP2 match
obcat Origin of B-category
The parameter is used as the origin for B-category analysis, where it is decided whether certain B-subscriber services should be suppressed.
OBCAT is used in the block SUA.
ocn Original called party ID
This parameter determines whether the original called party ID should be included when the SCF is invoked.
0 Not included 1 Included
2 Included if available odestid Format of own address
0 Local (SSCP)
1 SPC + SSN
2-27 Pointer to first digit of
2 Included if available
rotr Route origin transferring
This indicator determines whether the route origin should be transferred from the incoming side to the outgoing side.
0 No transferring allowed 1 Transferring allowed scfr SCF simulation handling
1 Normal (No simulation) 2 Simulation
3 Message logging
4 Simulation with pretty print
5 Message logging with pretty print
6 Service logic tracing
7 Service logic tracing and message logging
8 Service logic tracing and message logging with pretty print
sec Selection case
This parameter indicates which type of CLSM is supported for this call to an IN identifier.
0 Originating CLSM 1 Terminating CLSM sfc Service filtering criteria
0 No Service filtering analysis 1 Service filtering analysis
shreq Soft or hard request
Indicates whether a soft or hard request is to be used to fetch the calling party number and calling party category.
If number or category are not available, in own exchange, a hard request will initiate a request backward in the network.
A soft request will NOT initiate a request backward.
0 Hard request
CorrelationID is sent in generic
Application Information Traffic Activity Code (4/155 18-ATP 210 11 Uen.).
tos Type of seizure
The type of seizure indicates a function family group.
For a description of the values, see Application Information Traffic Activity Code (4/155 18-ATP 210 11 Uen.).
totr Timesupervision origin transferring This indicator determines whether the timesupervision origin should be transferred from the incoming side to the outgoing side.
0 No transferring allowed 1 Transferring allowed
tsc Type of telecommunication service This parameter is used to identify the telecommunication service code.
For a description of the values, see Application Information Traffic Activity Code (4/155 18-ATP 210 11 Uen.).
tsus This parameter contains basic call=
related information in order to control the timer for network initiated suspend in the SSP node.
EOT DURING PRINTOUT
The operator has cancelled the printout
NONE
No data is to be printed Function
This printout is received as an answer printout to command SWISP, and lists the above mentioned parameters for IN service trigger identifiers specified in the command. The second line in the printout specifies if the values printed are from the operating or non operating area, as specified by the SWISP command.
Printout Type Answer printout Printout Block SSFTDA1