Binary, Octal, Decimal, BCD, He

Chapter Contents

2.7 Binary, Octal, Decimal, BCD, He

For fulllfilling different kinds of internal manipulation, DVP-PLC appies 5 foramts of number systems. Each number system has its specific purpose and function described as below.

1. Binary Number, (BIN)

PLC internally calculates, operates, and stores the value in Binary format. 2. Octal Number, (OCT)

The external I/O points of DVP-PLC are numbered in octal format. e.g.

External inputs: X0～X7, X10～X17, …, X377. (No. of device) External outputs: Y0～Y7, Y10～Y17, …, Y377. (No. of device) 3. Decimal Number, (DEC)

DVP-PLC appies decimal operation in situations below:

 Set value for timers and counters, e.g. TMR C0 K50. (K value)  No. of S, M, T, C, D, E, F, P, I devices, e.g. M10, T30. (No. of device)  For use of operand in API instructions, e.g. MOV K123 D0. (K value) 4. BCD (Binary Coded Decimal)

BCD format takes 1 digit or 4 bits to indicate a Decimal value, so that data of consecutive 16 bits indicates a 4-digit decimal value. Used mainly for reading values from DIP switches or sending data to 7-segement displays

5. Hexadecimal Number, HEX

DVP-PLC appies Hexadecimal operation in situations below:

 For use of operand in API instructions, e.g. MOV H1A2B D0。(H value)

Constant (K): A decimal number in a PLC is generally preceded by K. For example, K100 represents the decimal number 100.

Exception:

If K is used with an X/Y/M/S device, a nibble device, a byte device, a word device, or a double word device will be formed.

Example:

K1Y10 represents a device composed of 4 bits, K2Y10 represents a device composed of 8 bits, K3Y10 represents a device composed of 12 bit, and K4Y10 represents a device composed of 16 bits. K1M100 represents a device composed of 4 bits, K2M100 represents a device composed of 8 bits, K3M100 represents a device composed of 12 bit, and

Constant (H): A hexadecimal number in a PLC is generally preceded by H. For example, the hexadecimal number H100 represents the decimal number 256.

Reference Table: Binary (BIN) Octal (OCT) Decimal (K) (DEC) BCD

(Binary Code Decimal)

Hexadecimal (H) (HEX) For PLC internal operation No. of X, Y relay Costant K, No. of registers M, S, T, C, D, E, F, P, I devices

For DIP Switch and 7-

segment display Constant H

0000 0 0 0000 0 0001 1 1 0001 1 0010 2 2 0010 2 0011 3 3 0011 3 0100 4 4 0100 4 0101 5 5 0101 5 0110 6 6 0110 6 0111 7 7 0111 7 1000 10 8 1000 8 1001 11 9 1001 9 1010 12 10 0000 A 1011 13 11 0001 B 1100 14 12 0010 C 1101 15 13 0011 D 1110 16 14 0100 E 1111 17 15 0101 F 10000 20 16 0110 10 10001 21 17 0111 11

2.8 M Relay

The types and functions of special auxiliary relays (special M) are listed in the table below. Care should be taken that some devices of the same No. may bear different meanings in different series MPUs. Special M and special D marked with “*” will be further illustrated in 2.13. Columns marked with “R” refers to “read only”, “R/W” refers to “read and write”, “-“ refers to the status remains unchanged and “#” refers to that system will set it up according to the status of the PLC.

Special M Function ES2 EX2 SS2 SA2 SE SX2 OFF  ON STOP  RUN RUN  STOP Attrib. Latch -ed Default

M1000* Monitor normally open contact ○ ○ ○ ○ OFF ON OFF R NO OFF M1001* Monitor normally closed contact ○ ○ ○ ○ ON OFF ON R NO ON M1002*

Enable single positive pulse at the moment when RUN is activate (Normally OFF)

○ ○ ○ ○ OFF ON OFF R NO OFF

M1003*

Enable single negative pulse at the moment when RUN is activate (Normally ON)

○ ○ ○ ○ ON OFF ON R NO ON M1004* ON when syntax errors occur ○ ○ ○ ○ OFF OFF - R NO OFF M1008* Watchdog timer (ON: PLC WDT time out) ○ ○ ○ ○ OFF OFF - R NO OFF M1009 Indicate LV signal due to 24VDC _{insufficiency} ○ ○ ○ ○ OFF - - R NO OFF M1011* 10ms clock pulse, 5ms ON/5ms OFF ○ ○ ○ ○ OFF - - R NO OFF M1012* 100ms clock pulse, 50ms ON / 50ms

OFF ○ ○ ○ ○ OFF - - R NO OFF

M1013* 1s clock pulse, 0.5s ON / 0.5s OFF ○ ○ ○ ○ OFF - - R NO OFF M1014* 1 min clock pulse, 30s ON / 30s OFF ○ ○ ○ ○ OFF - - R NO OFF M1015* Enable high-speed timer ○ ○ ○ ○ OFF - - R/W NO OFF M1016* Indicate Year display mode of RTC. ○ ○ ○ ○ OFF - - R/W NO OFF M1017* ±30 seconds correction on real time clock ○ ○ ○ ○ OFF - - R/W NO OFF M1018 Flag for Radian/Degree, ON for degree ○ ○ ○ ○ OFF - - R/W NO OFF M1020 Zero flag ○ ○ ○ ○ OFF - - R NO OFF

Special M Function ES2 EX2 SS2 SA2 SE SX2 OFF  ON STOP  RUN RUN  STOP Attrib. Latch -ed Default

M1021 Borrow flag ○ ○ ○ ○ OFF - - R NO OFF M1022 Carry flag ○ ○ ○ ○ OFF - - R NO OFF M1024 COM1 monitor request ○ ○ ○ ○ OFF - - R/W NO OFF M1025* Indicate incorrect request for

communication ○ ○ ○ ○ OFF - - R NO OFF M1026 RAMP mode selection ○ ○ ○ ○ OFF - - R/W NO OFF M1027 PR output mode selection (8/16 bytes) ○ ○ ○ ○ OFF - - R/W NO OFF M1028 Switch T64~T126 timer resulotion _{(10ms/100ms). ON =10ms} ○ ○ ○ ○ OFF - - R/W NO OFF M1029* CH0 (Y0, Y1) pulse output execution

completed. ○ ○ ○ ○ OFF - - R NO OFF

M1030* Pulse output Y1 execution completed ○ ○ ○ ○ OFF - - R NO OFF M1031* Clear all non-latched memory ○ ○ ○ ○ OFF - - R/W NO OFF M1032* Clear all latched memory ○ ○ ○ ○ OFF - - R/W NO OFF M1033* Output state latched at STOP ○ ○ ○ ○ OFF - - R/W NO OFF M1034* Disable all Y outputs ○ ○ ○ ○ OFF - - R/W NO OFF M1035* Enable X7 input point as RUN/STOP

switch ○ ○ ○ ○ - - - R/W YES OFF

M1037*

Enable 8-sets SPD function (Has to be used with D1037) (SE does not support this function.)

╳ ╳ ○ ○ OFF OFF OFF R/W NO OFF

M1038 Switch T200~T255 timer resulotion

(10ms/1ms). ON = 1ms ○ ○ ○ ○ OFF - - R/W NO OFF M1039* Fix scan time ○ ○ ○ ○ OFF - - R/W NO OFF M1040 Disable step transition ○ ○ ○ ○ OFF - - R/W NO OFF M1041 Step transition start ○ ○ ○ ○ OFF - OFF R/W NO OFF M1042 Enable pulse operation ○ ○ ○ ○ OFF - - R/W NO OFF M1043 Zero return completed ○ ○ ○ ○ OFF - OFF R/W NO OFF M1044 Zero point condition ○ ○ ○ ○ OFF - OFF R/W NO OFF M1045 Disable “all output reset” function ○ ○ ○ ○ OFF - - R/W NO OFF M1046 Indicate STL status ○ ○ ○ ○ OFF - - R NO OFF M1047 Enable STL monitoring ○ ○ ○ ○ OFF - - R/W NO OFF M1048 Indicate alarm status ○ ○ ○ ○ OFF - - R NO OFF M1049 Enable alarm monitoring ○ ○ ○ ○ OFF - - R/W NO OFF M1050 Disable interruption I000 / I001 ○ ○ ○ ○ OFF - - R/W NO OFF M1051 Disable interruption I100 / I101 ○ ○ ○ ○ OFF - - R/W NO OFF M1052 Disable interruption I200 / I201 ○ ○ ○ ○ OFF - - R/W NO OFF M1053 Disable interruption I300 / I301 ○ ○ ○ ○ OFF - - R/W NO OFF M1054 Disable interruption I400 / I401 ○ ○ ○ ○ OFF - - R/W NO OFF M1055 Disable interruption I500 / I501 ○ ○ ○ ○ OFF - - R/W NO OFF M1056 Disable interruption I600~I699 ○ ○ ○ ○ OFF - - R/W NO OFF M1057

Disable interruption I700~I799

Disable interruption I805~I899 (V2.00 and above are supported.)

○ ○ ○ ○ OFF - - R/W NO OFF M1058 COM3 monitor request ○ ╳ ○ ○ OFF - - R/W NO OFF M1059 Disable high-speed counter interruptions _I010~I080 ○ ○ ○ ○ OFF - - R/W NO OFF M1060 System error message 1 ○ ○ ○ ○ OFF - - R NO OFF M1061 System error message 2 ○ ○ ○ ○ OFF - - R NO OFF M1062 System error message 3 ○ ○ ○ ○ OFF - - R NO OFF M1063 System error message 4 ○ ○ ○ ○ OFF - - R NO OFF M1064 Incorrect use of operands ○ ○ ○ ○ OFF OFF - R NO OFF M1065 Syntax error ○ ○ ○ ○ OFF OFF - R NO OFF M1066 Loop error ○ ○ ○ ○ OFF OFF - R NO OFF M1067* Program execution error ○ ○ ○ ○ OFF OFF - R NO OFF M1068* Execution error locked (D1068) ○ ○ ○ ○ OFF - - R NO OFF

M1070 Switching clock pulse of Y1 for PWM

instruction (ON: 100us; OFF: 1ms) ○ ○ ○ ○ OFF - - R/W NO OFF M1071 Switching clock pulse of Y3 for PWM _{instruction (ON: 100us; OFF: 1ms)} ○ ○ ○ ○ OFF - - R/W NO OFF M1072 PLC status (RUN/STOP), ON = RUN ○ ○ ○ ○ OFF ON OFF R/W NO OFF M1075 Error occurring when write in Flash ROM ○ ○ ○ ○ OFF - - R NO OFF

Special M Function ES2 EX2 SS2 SA2 SE SX2 OFF  ON STOP  RUN RUN  STOP Attrib. Latch -ed Default

M1078 Y0/CH0(Y0, Y1) pulse output pause

(immediate) ○ ○ ○ ○ OFF OFF - R/W NO OFF M1079 Y1 pulse output pause (immediate) ○ ○ ○ ○ OFF OFF - R/W NO OFF M1080 COM2 monitor request ○ ○ ○ ○ OFF - - R/W NO OFF M1081 Changing conversion mode for FLT

instruction ○ ○ ○ ○ OFF - - R/W NO OFF M1083*

Selecting X6 pulse-width detecting mode. M1083 = ON, detecting pulse-width when X6 = ON; M1083 = OFF, detecting pulse- width when X6 = OFF.

○ ○ ○ ○ OFF - - R/W NO OFF

M1084*

Enabling X6 Pulse width detecting function. (has to be used with M1183 and D1023)

○ ○ ○ ○ OFF OFF OFF R/W NO OFF M1085 Selecting DVP-PCC01 duplicating function ○ ○ ○ ○ OFF - - R/W NO OFF M1086 Enabling password function for DVP-

PCC01 ○ ○ ○ ○ OFF - - R/W NO OFF

M1088

Matrix comparison.

Comparing between equivalent values (M1088 = ON) or different values (M1088 = OFF).

○ ○ ○ ○ OFF OFF - R/W NO OFF

M1089

Indicating the end of matrix comparison. When the comparison reaches the last bit, M1089 = ON.

○ ○ ○ ○ OFF OFF - R NO OFF

M1090

Indicating start of matrix comparison. When the comparison starts from the first bit, M1090 = ON.

○ ○ ○ ○ OFF OFF - R NO OFF

M1091

Indicating matrix searching results. When the comparison has matched results, comparison will stop immediately and M1091 = ON.

○ ○ ○ ○ OFF OFF - R NO OFF

M1092

Indicating pointer error. When the pointer Pr exceeds the comparison range, M1092 = ON

○ ○ ○ ○ OFF OFF - R NO OFF

M1093 Matrix pointer increasing flag. Adding 1 to

the current value of the Pr. ○ ○ ○ ○ OFF OFF - R/W NO OFF M1094 Matrix pointer clear flag. Clear the current

value of the Pr to 0 ○ ○ ○ ○ OFF OFF - R/W NO OFF M1095 Carry flag for matrix rotation / shift /

output. ○ ○ ○ ○ OFF OFF - R NO OFF

M1096 Borrow flag for matrix rotation/shift/input ○ ○ ○ ○ OFF OFF - R/W NO OFF M1097 Direction flag for matrix _{rotation/displacement} ○ ○ ○ ○ OFF OFF - R/W NO OFF M1098 Counting the number of bits which are “1”

or “0” ○ ○ ○ ○ OFF OFF - R/W NO OFF M1099 ON when the bits counting result is “0” ○ ○ ○ ○ OFF OFF - R/W NO OFF M1102* Y2/CH1 (Y2, Y3) pulse output execution

completed ○ ○ ○ ○ OFF - - R/W NO OFF M1103* Y3 pulse output completed ○ ○ ○ ○ OFF - - R/W NO OFF

M1104 Y2/CH1 (Y2, Y3) pulse output pause

(immediate) ○ ○ ○ ○ OFF OFF - R/W NO OFF M1105 Y3 pulse output pause (immediate) ○ ○ ○ ○ OFF OFF - R/W NO OFF M1106

Zero point selection. M1106=ON, change the zero point to the right of DOG switch for zero return on CH0.

○ ○ ○ ○ OFF OFF - R/W NO OFF

M1107

Zero point selection. M1107=ON, change the zero point to the right of DOG switch for zero return on CH1.

○ ○ ○ ○ OFF OFF - R/W NO OFF

M1108 Y0/CH0 (Y0, Y1) pulse output pause

(ramp down) ○ ○ ○ ○ OFF OFF - R/W NO OFF M1109 Y1 pulse output pause (ramp down) ○ ○ ○ ○ OFF OFF - R/W NO OFF M1110 Y2/CH1 (Y2, Y3) pulse output pause

(ramp down) ○ ○ ○ ○ OFF OFF - R/W NO OFF M1111 Y3 pulse output pause (ramp down) ○ ○ ○ ○ OFF OFF - R/W NO OFF M1112 Switching clock pulse of Y0 for PWM

Special M Function ES2 EX2 SS2 SA2 SE SX2 OFF  ON STOP  RUN RUN  STOP Attrib. Latch -ed Default

M1113 Switching clock pulse of Y2 for PWM

instruction (ON: 100us; OFF: 1ms) ○ ○ ○ ○ OFF OFF - R/W NO OFF M1119* Enable 2-speed output function of

DDRVI instruction ○ ╳ ○ ○ OFF OFF OFF R/W NO OFF M1120*

Retaining the communication setting of COM2 (RS-485), modifying D1120 will be invalid when M1120 is set.

○ ○ ○ ○ OFF OFF - R/W NO OFF

M1121 For COM2(RS-485), data transmission _ready ○ ○ ○ ○ OFF OFF - R NO OFF M1122 For COM2(RS-485), sending request ○ ○ ○ ○ OFF OFF - R/W NO OFF M1123 For COM2(RS-485), data receiving _completed ○ ○ ○ ○ OFF OFF - R/W NO OFF M1124 For COM2(RS-485), data receiving ready ○ ○ ○ ○ OFF OFF - R/W NO OFF M1125 For COM2(RS-485), communication ready

status reset ○ ○ ○ ○ OFF OFF OFF R/W NO OFF M1126 For COM2(RS-485), set STX/ETX as user

defined or system defined ○ ○ ○ ○ OFF OFF OFF R/W NO OFF M1127

For COM2(RS-485), data sending / receiving / converting completed. (RS instruction is not supported)

○ ○ ○ ○ OFF OFF OFF R/W NO OFF

M1128 For COM2(RS-485), _{Transmitting/Receiving status Indication} ○ ○ ○ ○ OFF OFF OFF R/W NO OFF M1129 For COM2(RS-485), receiving time out ○ ○ ○ ○ OFF OFF - R/W NO OFF M1130 For COM2(RS-485), STX/ETX selection ○ ○ ○ ○ OFF OFF - R/W NO OFF M1131

For COM2(RS-485), ON when MODRD/RDST/MODRW data is being converted from ASCII to Hex

○ ○ ○ ○ OFF OFF - R NO OFF

M1132 ON when there are no communication

related instructions in the program ○ ○ ○ ○ OFF - - R NO OFF M1136* For COM3(RS-485/USB), retaining

communication setting ○ ╳ ○ ○ OFF - - R/W NO OFF M1137 Retain DNET mapping data during non-

executing period ╳ ╳ ○ ○ - - - R/W NO OFF M1138*

For COM1 (RS-232), retaining

communication setting. Modifying D1036 will be invalid when M1138 is set.

○ ○ ○ ○ OFF - - R/W NO OFF

M1139* For COM1(RS-232), ASCII/RTU mode

selection (OFF: ASCII; ON: RTU) ○ ○ ○ ○ OFF - - R/W NO OFF M1140 For COM2 (RS-485), MODRD / MODWR

/ MODRW data receiving error ○ ○ ○ ○ OFF OFF - R NO OFF M1141 For COM2 (RS-485), MODRD / MODWR _{/ MODRW parameter error} ○ ○ ○ ○ OFF OFF - R NO OFF M1142 Data receiving error of VFD-A handy

instructions ○ ○ ○ ○ OFF OFF - R NO OFF M1143* For COM2(RS-485), ASCII/RTU mode

selection (OFF: ASCII; ON: RTU) ○ ○ ○ ○ OFF - - R/W NO OFF M1148

After the instruction DELAY is executed, the execution of the program following DELAY is delayed for 5us.

V3.2 V3.0V2.6

V1.4V2.4 OFF OFF - R/W NO OFF

M1156*

Enabling the mask and alignment mark function on I400/I401(X4) corresponding to Y0

○ ○ ○ ○ OFF OFF - R/W NO OFF

M1158*

Enabling the mask and alignment mark function on I600/I601(X6) corresponding to Y2

○ ○ ○ ○ OFF OFF - R/W NO OFF M1161 8/16 bit mode (ON = 8 bit mode) ○ ○ ○ ○ OFF - - R/W NO OFF

M1162

Switching between decimal integer and binary floating point for SCLP instruction. ON: binary floating point; OFF: decimal integer

○ ○ ○ ○ OFF - - R/W NO OFF

M1167 16-bit mode for HKY input ○ ○ ○ ○ OFF - - R/W NO OFF M1168 Designating work mode of SMOV ○ ○ ○ ○ OFF - - R/W NO OFF M1177

Enable the communication instruction for Delta VFD series inverter.

ON: VFD-A (Default), OFF: other models of VFD

Special M Function ES2 EX2 SS2 SA2 SE SX2 OFF  ON STOP  RUN RUN  STOP Attrib. Latch -ed Default

M1178 Enable knob VR0 ╳ ╳ ○ ○ OFF - - R/W NO OFF M1179 Enable knob VR1 ╳ ╳ ○ ○ OFF - - R/W NO OFF M1180 The EX2/SX2 model reads analog-to-

digital values immediately. ○ ╳ ╳ ○ OFF - - R/W NO OFF M1181 The EX2/SX2 model outputs digital-to-

analog values immediately. ○ ╳ ╳ ○ OFF - - R/W NO OFF

M1182*

M1182 = ON, disable auto-mapping function when connected with left-side modules.

 For SA2 /SX2/SE models, values of AIO modules will be auto-mapped to D9800 and above.

 If the left side is connected with a communication module, additional 10 words will be occupied. Ex: 04AD-SL + EN01-SL + SA2, average value of Ch1~Ch4 of 04AD-SL maps to D9810~D9813.

╳ ╳ ○ ○ ON - - R/W NO ON

M1183*

M1183 = ON, disable auto mapping function when connected with special modules

#: ES2/EX2: OFF; SS2/SA2/SX2/SE: ON (maps to D9900 and above)

○ ○ ○ ○ # - - R/W NO #

M1190 Set Y0 high speed output as 0.01 ~ 10Hz ○ ○ ○ ○ OFF OFF - R/W NO OFF M1191 Set Y1 high speed output as 0.01 ~ 10Hz ○ ○ ○ ○ OFF OFF - R/W NO OFF M1192 Set Y2 high speed output as 0.01 ~ 10Hz ○ ○ ○ ○ OFF OFF - R/W NO OFF M1193 Set Y3 high speed output as 0.01 ~ 10Hz ○ ○ ○ ○ OFF OFF - R/W NO OFF M1200 C200 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1201 C201 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1202 C202 counting mode ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1203 C203 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1204 C204 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1205 C205 counting mode (ON :count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1206 C206 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1207 C207 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1208 C208 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1209 C209 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1210 C210 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1211 C211 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1212 C212 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1213 C213 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1214 C214 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1215 C215 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1216 C216 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1217 C217 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1218 C218 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1219 C219 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1220 C220 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1221 C221 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1222 C222 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1223 C223 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1224 C224 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1225 C225 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1226 C226 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1227 C227 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1228 C228 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1229 C229 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1230 C230 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1231 C231 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF C232 counting mode (ON: count down) ╳ ○ ╳ ╳ OFF - - R/W NO OFF M1232

C232 counter monitor (ON: count down) ○ ╳ ○ ○ OFF - - R NO OFF M1233 C233 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF

Special M Function ES2 EX2 SS2 SA2 SE SX2 OFF  ON STOP  RUN RUN  STOP Attrib. Latch -ed Default

M1234 C234 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF M1235 C235 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1236 C236 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1237 C237 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1238 C238 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1239 C239 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1240 C240 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1241 C241 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1242 C242 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1243 C243 Reset function control. ON = R _{function disabled} ○ ○ ○ ○ OFF - - R/W NO OFF M1244 C244 Reset function control. ON = R

function disabled ○ ○ ○ ○ OFF - - R/W NO OFF M1245 C245 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF M1246 C246 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF M1247 C247 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF M1248 C248 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF M1249 C249 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF M1250 C250 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF M1251 C251 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF M1252 C252 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF M1253 C253 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF M1254 C254 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF M1257 Set the ramp up/down of Y0, Y2 to be “S

curve.” ON = S curve. ○ ○ ○ ○ OFF OFF - R/W NO OFF M1260 Set up X7 as the reset signal for software

counters C235 ~ C241 ○ ○ ○ ○ OFF - - R/W NO OFF M1262

Enable cyclic output for table output function of DPTPO instruction. ON = enable.

○ ○ ○ ○ OFF OFF - R/W NO OFF

M1270 C235 counting mode (ON: falling-edge