F.3.1: BULK MUD AND CEMENT TANKS
Six (6) pressure tanks 60 psi each approx 55 m3 /1940 ft3 capacity c/w 5' fill, 5” discharge, 5” vent. Each tank with load cell and high level indicator
Total Bulk Storage capacity: 330 m³
NB: All tanks are fitted with Thames Side VC 3500 Series 3 load cells for weighing and monitoring purposes.
F.3.2: MUD SURGE TANK
One (1) Vortex Ventures model SG848820-A mud surge tank for Barite / Bentonite non- pressurized capacity 2m³ suspended with load cell and high and low level indicators.
G – CASING / CEMENTING EQUIPMENT
G.1 - CASING EQUIPMENT
Third party supply
G.2 - CEMENTING EQUIPMENT
H – INSTRUMENTATION / COMMUNICATION
H.1 - DRILLERS INSTRUMENTATION AT DRILLERS POSITION
The drilling instrumentation system, DrillView, is supplied by AKMH and includes the Drilling Control and Data Acquisition (DCDA) systems. The following data can be displayed as part of the integrated drilling instrumentation system:
• Standpipe pressure • Casing pressure • Block position • Hook load • Drilling torque • Drilling speed • Rotary speed • Trip tank volume • Trip tank acc. volume • Trip tank diff. volume • Pit volume
• Mud pump strokes • Mud flow out • Auxiliary 1 – 5 input • Tong torque • Active volume • Total volume • Bit depth • Total depth • Total stroke • Active SPM • Flow in • WOB • Ton-mile
• Mud return change • Pumped volume • ROP
• Block / run speed • Stand count • Gain / loss
• Well and string section volume and stroke
H.2 - DRILLING PARAMETER RECORDER
• Displays for drilling parameter recorder at Driller’s Cabin, Toolpusher’s Office and Company Man’s Office showing:
o Weight on Bit (WOB) o Rate of Penetration (ROP) o Pump Pressure
o Pump Speed o Rotary Torque o Drag
H.3 - INSTRUMENTATION AT CHOKE MANIFOLD
The choke and kill manifold is equipped with the following instrumentation: • Two (2) pressure indicators
• Four (4) pressure transmitters
• Two (2) choke valve position transmitters
H.4 - INSTRUMENTATION AT STANDPIPE
The cement standpipe and manifold is fitted with a single pressure indicator
The mud manifold is fitted with dual pressure transmitter and pressure indicators, one set per standpipe.
H.5 - DEVIATION EQUIPMENT
• One (1) MD Totco drift recorder, deviation range 0 to 8 degrees
H.6 - RIG COMMUNICATION SYSTEMS
H.6.1: RIG TELEPHONE SYSTEM AND PUBLIC ADDRESS SYSTEM H.6.1.1: Combined Paging (PAGA) and Telephone (PABX) System
• Two (2) freestanding 19” industrial cubicle for PAGA system
• One (1) freestanding 19” industrial cubicle for PABX system
Telephone exchange equipped with 63 extensions with the following levels of landline access pre-programmed;
• Three (3) levels for PA access
• Two (2) levels for platform exchange access • One (1) level for inmarsat access
H.6.1.2: PA System
The PA system shall be equipped for the following inputs; • Three (3) Microphone inputs
• Two (2) PABX inputs • Four (4) Alarm inputs
Microphones are located in the tool pusher’s office, driller’s cabin and radio room. • Two (2) zone selections
o Zone 1: Work areas and offices o Zone 2: All call
• Four (4) Alarm selections
o Alarm 1: Fire / Combustible Gas o Alarm 2: H2S Gas
o Alarm 3: General alarm o Alarm 4: Abandon Vessel
H.6.1.3: Power Supplies
PA/PABX system operates with the following supplies; • AC emergency supply 230 VAC 60 HZ
• AC UPS 230 VAC 60 HZ
H.6.1.4: Hospital Call System
A hospital call bell system is installed with annunciators in the radio room, push button at each hospital berth, rotating beacon outside hospital and a bell in the medic’s cabin.
H.6.1.5: Drilling Communication System
A drilling communication system is installed. The system provides communication between the driller’s cabin and the BOP storage area, monkey board and drill floor. The system is hands free with a talk back function.
H.7 - ENVIRONMENTAL INSTRUMENTATION
• Barograph
• Temperature recorder
• Wind speed / direction indicator
H.8 - NAVIGATION INSTRUMENTATION
• Fog Horn, mechanical hand powered • Battery operated Bull horn
• Daylight signaling lamp • Fog bell 250 mm diameter • Clinometers
• Aircraft warning lights (derrick and cranes)
• Self contained solar powered aircraft warning lights (legs) • Marine signal lanterns
• Helideck perimeter lighting
H.9 - EXTERNAL COMMUNICATION EQUIPMENT
• Three (3) VHF radio telephone with built in DSC
• Two (2) MF/HF radio telephone with built in DSC / watch receiver
• One (1) Navtex
• One (1) Inmarsat C enhanced group calling system
• One (1) satellite emergency position indicating radio beacon
• Five (5) Portable two-way VHF radio telephone for life boat
• Five (5) Radar transponder for life boat
• GMDSS radio equipment with;
o One (1) stabilized Inmarsat F terminal o Ten (10) hand held walkie-talkie 6 channels
o One (1) VHF air band base station for Helicopter communication o One (1) aeronautical non-directional beacon
I – PRODUCTION TEST EQUIPMENT
I.1 - BURNERS
Third party supply (refer to I-2)
I.2 - BURNER BOOMS
Both the starboard aft and port aft side shells have been reinforced for the installation of burner booms of up to 120 ft in length.
I.3 - PIPING ON BURNER BOOMS
Third party supply
I.4 - SPRINKLER SYSTEM
Each flare boom location has a Unitor supplied water curtail spray header installed that can be supplied from either the fire main system or the sea water service pump.
I.5 - FIXED PIPING FOR WELL TESTING
Fixed Flare / Well Testing pipework is installed suitable for H2S service. Discharge is selectable to either Port or Starboard or to isolation. All connections are hammer union type.
• 4” 1500 psi wp Fig 602 welded Gas line • 4” 1500 psi wp Fig 602 welded Oil line
• 4” 200 psi wp from sea water service pump or fire main system
I.6 - AUXILIARY POWER AVAILABILITY
• One (1) 480 V 32 Amp supply for the field laboratory • One (1) 480V 32 Amp supply for a crude oil transfer pump • One (1) 480V 32 Amp supply for electric heaters
K – ACCOMMODATION
The rig provides accommodation for 113 persons and is positively pressurized on all levels and fully air-conditioned. The accommodation is certified as HAB+ by ABS.
K.1 - OFFICES
• One (1) Mechanic and Electricians Office EL 1800
• One (1) Store Keepers Office EL 5150
• Three (3) Client and Service Company Offices EL 18100
• Three (3) Contractor Offices EL 18100
• One (1) Tool Pushers Office EL 18100
• One (1) Radio Office EL 21300
• One (1) BCR EL 21300
K.2 - LIVING QUARTERS
K.2.1: GENERAL
Partitioning and door system with the following characteristics
• 50 mm thickness B15 partitioning, with faces of PVC coated galvanized mild steel sheet minimum thickness 0.6 mm.
• Range including 25 mm nominal thickness liner panels and noise reduction panels K.2.2: BEDROOMS
• Level 1: Total 2 persons
o One (1) 2 man medics quarters • Level 2: Total 66 persons
o Thirty three (33) 2 man rooms • Level 3: Total 38 persons
o Nineteen (19) 2 man rooms • Level 4: Total 7 persons
o Five (5) 1 man rooms o One (1) 2 man room K.2.3: UTILITY ROOMS
Inside Hull:
• Mechanical Workshop
• Electrical Workshop
• Chemical Store
• Heavy Tool Store
J – WORKOVER TOOLS
Main Deck: • LQ Utility Room • Freezer Room 1 • Paint Locker • Marine Store • UPS Room • Deck Canteen Above Main Deck:
• Emergency Generator Room Level 1:
• Drystore
• Chiller Room
• Freezer Room 2
• Galley
• Mess Room (56 Seats)
• TV Room
• Quiet Lounge
• Gymnasium
• AHU Room
• Gents Locker Room (83 x 2 Lockers)
• Gents Toilet
• Laundry and Linen Locker
• Hospital (3 Beds) + Bathroom
• Campboss Office Level 2: • AHU Room • Janitor Room • Domestic Store • Linen Locker Level 3: • Coffee Area
• Ladies Change Room and Toilet
• Public Toilet
• Meeting Room
• AHU room
• Linen Locker
• Janitors Room / Toilet Level 4: • Heli-Lounge / Cinema • Library • Public Toilet • AHU Room • Telephone Cubicle
K.2.4: AIR CONDITIONING AND HEATING
• Two (2) Carrier AquaForce model 30XAA0806P centralized air cooled chilled water units, each sized for 60% of the total accommodation cooling
• Two (2) Carrier AquaForce model 38AKS034 centralized air cooled chilled water units, each sized for 60% of the remaining rig cooling
• One (1) Carrier air handling unit on each level of the quarters
• One AHU mounted on the machinery deck to service the Electrical Switchboard room, the VFD room, the mechanical and electrical office and the storekeepers office
• Independent cooling / heating units for areas such as the, Driller’s Cabin, LER Crane Cabins, etc.
K.2.5: FREEZING AND REFRIGERATION SYSTEMS FOR PROVISIONS
• One (1) Freezer walk-in compartment, Air cooled. Temp -23°C freezer unit cooling provided by one Guntner S-GSF/031.1D/27-EX unit combined with a Guntner GCO- H/4/32/2.20 condenser
• One (1) Chiller walk-in compartment, Air cooled. Temp +2°C chiller unit cooling provided by one Guntner S-GSF/031.1D/17-AX unit combined with a Guntner GCO- H/4/32/2.20 condenser
L – SAFETY EQUIPMENT
L.1 - GENERAL SAFETY EQUIPMENT
L.1.1: GENERAL PERSONNEL PROTECTIVE GEAR • Lot safety glasses
• Lot safety helmets
• Lot safety boots (with anti perforation soles)
• Lot coveralls
• Lot hearing protectors
• Lot safety gloves
• Lot of full face visors
• Lot of eye shield
• Lot of dust masks
• Lot of proof hand torches c/w batteries
• Lot of safety belts c/w lines
• Lot of work vests for overboard work L.1.2: DECONTAMINATION STATIONS
• Seven (7) Eye Wash stations
• Four (4) Safety Showers
L.1.3: DERRICK SAFETY EQUIPMENT • One (1) Derrick escape chute
• One set of anti-fall devices
• Derrick safety belt
L.1.4: DERRICK CLIMBING ASSISTANT
The derrick is fitted with a SALA Lad Saf inertia type safety climbing system and harness. L.1.5: FRESH AIR BLOWERS (BUG BLOWERS)
• One (1) bug blower is installed at the drill floor for ventilation and fresh air supply • One (1) bug blower is installed at the shaker house for ventilation and fresh air supply • One (1) bug blower is installed in the pit room for ventilation and fresh air supply
L.1.6: PROTECTIVE CLOTHING & EQUIPMENT AGAINST CORROSIVE SUBSTANCES
• Lot of aprons
• Lot of gloves – elbow length for chemical handling L.1.7: WARNING SIGNS
• One (1) set of safety & warning signs.
L.1.8: MISCELLANEOUS SAFETY EQUIPMENT Required by Class and Regulatory Bodies;
• One (1) flame proof safety lamp
• Two (4) embarkation ladders of rope or lightweight chain construction and safety belts (harness type) with 300 ft of ⅜” Dacron line
• One (1) line throwing apparatus
• Twelve (12) rocket parachute flares
L.2 - GAS / FIRE / SMOKE DETECTION
L.2.1: OMEGA INTEGRATED FIXED GAS & H2S DETECTION & ALARM SYSTEM Sensor locations;
• Cellar deck area
• Drill floor area
• Shale shakers in the mud treatment house
• Mud pits room
• Accommodation ventilation intakes L.2.2: FIRE AND SMOKE DETECTION
All spaces of the unit are monitored by the appropriate type of detector.
One (1) panel of controllers with buzzer and LED’s located in radio room, connected to all detectors and manual call stations
O2 Meter (Portable)
L.3 - FIRE FIGHTING EQUIPMENT
L.3.1: FIXED FIRE EXTINGUISHING SYSTEMS There are four distinctive fixed fire fighting systems onboard:
• CO² System
• Foam System
• Misting System
• Water Deluge System
L.3.1.1: CO² System
Three zones on the rig are covered by independent fixed ABS and SOLAS compliant CO² systems supplied by Unitor Marine Systems;
• Electrical / VFD room;
o Stainless steel enclosure
o Eight (8) Nº 45 kg (67.5 litre) cylinders
o HP manifold
o Eleven (11) release nozzles
o Release cabinet & operating instructions mounted outside the electrical / VFD room
o Dual alarms and sirens
• Emergency generator room;
o Stainless steel enclosure
o Three (3) Nº 45 kg (67.5 litre) cylinders
o Three (3) release nozzles
o Release from the enclosure by “break glass’ box
o Operating instructions mounted on the enclosure
o Alarms and siren
• Paint Locker;
o Stainless steel enclosure
o One (1) Nº 45 kg (67.5 litre) cylinder
o HP piping
o Two (2) release nozzles
o Release from the enclosure by “break glass’ box
o Operating instructions mounted on the enclosure
o Alarms and siren
L.3.1.2: Foam System
Three zones on the rig are covered by independent fixed ABS and SOLAS compliant foam systems supplied by Unitor Marine Systems;
• BOP Area;
o One (1) FJM-80S ANSI 150# manually operated Monitor with self inducing nozzle and pick up tube
o One (1) Stainless steel 400 litre vertical liquid foam tank
o Liquid level indicator
o Foam concentrate 3% Uniral AFFF
• Mud Treatment House;
o One (1) foam tank skid unit
o One (1) 3” feed from the fire pump
o Fourteen (14) MV-25 nozzles;
− Four (4) in the treatment house main deck area
− Eight (8) in the treatment house intermediate deck
− Two (2) on the mud treatment house deck
o One (1) GRP 400 litre vertical liquid foam tank
o Liquid level indicator
o Foam concentrate 3% Uniral AFFF
• Mud Pits Area;
o One (1) foam tank skid unit
o One (1) 4” feed from the fire pump
o Nine (9) MV-34 nozzles;
− One (1) in Mud Pit 5
− Eight (8) in the Mud Pit room
o Ten (10) MV-19 nozzles;
− Two (2) each in mud pits 1 through 4 (total 8 Nº)
− One (1) each in mud pits 7 & 8 (total 2 Nº)
o Two (2) MV-15 nozzles;
− Two (2) in Mud Pit 6
o Two (2) MV-10 nozzles;
− One (1) each in Slug Pits 9 through 11 (total 3 Nº)
o One (1) GRP 600 litre vertical liquid foam tank
o Liquid level indicator
L.3.1.3: Misting System
The main generator room is protected by a SOLAS compliant Marioff Hi-Fog® fire extinguishing system. The system uses water at high pressure discharging through specially designed spray heads thereby creating a fine fog (mist) entering the protected space at high speed.
The system consists of the following components:
• Sprinkler pump unit and accumulator unit (SPAU 4+1) including;
o Five (5) electrical motors each connected to two (2) high pressure pumps producing 140 bar and 80 bar
o A water bottle accumulator consisting of 8 x 50 litre water bottles connected to a nitrogen bottle unit consisting of 8 x 50 litre bottles at 140 bar
o Capable of supplying 390 l/min
• A PLC operated section alarm filter and a control and indication panel at the Bridge and ECR
• Stainless Steel piping
• Section valves for machinery spaces
o M1 – main generator room intermediate deck
o M2 – main generator room tank top
o M3 – main generator room bilge
• Spray heads for machinery spaces
o Two types of spray heads are used in the machinery space;
− 4S 1MC 8MB 1000
− Twenty four (24) in the intermediate deck
− 4S 1MB 6MB 1000
− Ten (10) in the tank top
− 3S 1MB 4MB 1000
− Twenty four (24) in the bilge spaces
L.3.1.4: Water Deluge System
There are two separate ABS compliant Unitor Marine Systems water deluge / curtain systems onboard one serving the drill floor / BOP handling area and the other providing coverage to the burner boom stations port and starboard aft.
• Drill floor (120m²) – protected by a water deluge system of the fixed pipe nozzle type (12 N4W nozzles) supplying water at a blanket rate of 1740 l/min
• BOP handling area (200m²) – protected by a water deluge system of the fixed pipe nozzle type (10 N6W nozzles) supplying water at a blanket rate of 2530 l/min
• Well test area (40m²) – protected by a single manually operated water monitor The water deluge system is supplied for the main rig fire water pump through 4” dia headers. The area adjacent to the burner boom foundations at port and starboard aft are each covered by a fixed pipe nozzle water curtain system.
• Total coverage at each location = 10m high x 26m long = 260m²
• Seven (7) NF40050 nozzles per side supplying water at a blanket rate of 1689 l/min Both water curtain rails are supplied by the main rig fire pump through independent 6” headers.
L.3.2: PORTABLE EXTINGUISHERS
Portable fluid fire extinguishers of appropriate types and sufficient number in accommodation spaces, service spaces and fire stations to comply with requirements of Regulatory Bodies Administration.
Fire extinguishers must be mounted in fire stations’ fiberglass enclosure where possible. As a minimum; extinguishers are provided on following areas:
One (1) each in:
• Machinery rooms
• Cranes
• Cement unit area
• Mud lab
• Paint locker
• BOP control skid
• Rubber store
• Electrician & mechanic room
• Electrical shop
• Mechanical shop
• Hospital
• Galley Two (2) each in:
• Electrical room
• VFD room
• Radio room
• Each deck of the LQ
• Mud pump room
• Control Room
• Helicopter deck
• Welder shop
• Drill floor
Six (6) in generator room
Other portable extinguishers are located at further stations around the rig in accordance with class requirements.
L.3.3: FIRE FIGHTING SYSTEM
Two (2) Garbarino NU80-250L vertical centrifugal fire pumps, capacity 180 m³/hr, 120 m head, One (1) Jockey pump capacity 10 m³/hr, 60 m head
L.3.4: DRY POWDER FIRE EXTINGUISHER SYSTEM
One (1) remotely actuated R-102 system to protect galley hood. Actuator located at the exit from galley
L.3.5: HELIDECK FIXED FIRE FIGHTING SYSTEM
One (1) fixed foam fire fighting system in accordance with IMO MODU Code, CAP437, Classification Society and Regulatory Bodies requirements.
The system basics are:
• Foam bladder tank – Model MTB-H1000m, capacity = 1000 litres • Nº of monitors – 2 model FJM80
• Nº of hose reels – 2
• Nº of foam spray nozzles - 2
• Monitor throw – 40m (as defined by code) • Application rate – 6 l/min/m²
• Min operating time – set at 10 minutes
• Foam concentrate - AFFF type at a 3% concentration
L.4 - BREATHING APPARATUS
• Two (2) complete compressed air 30 minute self-contained breathing apparatus (SCBA) c/w spare bottles
• Breathing Air Recharge Compressor • Air Purity Test equipment
• Escape Masks
L.5 - EMERGENCY FIRST AID EQUIPMENT
• First Aid Kit
• Burn Kit
• Resuscitators
• Stretchers
• Two (2) lightweight fiberglass frame stretchers.
L.6 - HELIDECK RESCUE EQUIPMENT
One (1) labeled fiberglass locker with stainless steel hardware to stow the following equipment:
• Two (2) fire axes, Elkhart, 6 lbs
• One (1) crow bar
• One (1) hack saw with three (3) spare blades
• One (1) metal hook
• One (1) knife
• One (1) pair of heat resistant gloves
• One (1) heat resistant blanket
• One (1) cutting pliers/metal cutter
• One (1) set of instructions on use of emergency equipment
• One (1) set of first aid equipment in a metal waterproof case
L.7 - EMERGENCY WARNING ALARMS
L.7.1: VENTILATION FAILURE ALARM
The ventilation system in hazardous areas and to electrical equipment rendered non-explosion proof through loss of air pressurization is alarmed. The monitoring and indication panel is located in the Radio Room.
L.7.2: ENGINE ALARM PANEL
Each main engine is provided with an independent local alarm / shutdown panel. Shutdown functions include, overspeed, high water temperature and low lube oil pressure. Alarms include
overspeed, high water temperature, low lube oil pressure, low lube oil level, crankcase over pressure and expansion tank low level.
L.7.3: FIRE ALARM SYSTEM
All spaces are provided with manually operated contact makers that activate a fire alarm system main indicator board in the Radio Room.
L.8 - SURVIVAL EQUIPMENT
L.8.1: LIFE BOATS / SURVIVAL CRAFT
Three (3) Neptune Marine NPT75F TELB 60 man survival craft located at the accommodation level 3, forward, port and starboard sides. Totally enclosed reinforced fiberglass construction, diesel propelled with hydraulic engine start. Each fitted with engine block heaters (oil) and saltwater cooling. All lifeboats contain full ocean equipment and provisions in accordance with the ABS, IMO and SOLAS requirements. Each lifeboat is suspended on a Neptune Marine NPT85DP platform davit system equipped with a single electrically operated winch, maximum davit load is 90kN
Total capacity: 180 men L.8.2: LIFE RAFTS
Four (4) Thirty-five (35) person inflatable life rafts. Location: 2 Port side and 2 starboard on main deck. Total capacity: 140 men
L.8.3: RESCUE BOAT
One (1) SOLAS 1974, LSA Code class EC W.H. Brennan GJ6.0B-1 fast rescue craft, (FRC), is located atop the quarters at level 4 in a stand alone cradle. The FRC is launched and recovered by the deck cranes. The FRC is capable of holding 15 persons (max). Operating duration is a minimum of 4 hrs at 30 kts with 3 persons.
L.8.4: LIFE JACKETS
One hundred and forty (140) life jackets:
• One hundred and twenty (120) stowed in the staterooms of the accommodations.
• Ten (10) stowed on the drill floor
• Ten (10) stowed on the main deck. L.8.5: LIFEBOUYS
M – POLLUTION PREVENTION EQUIPMENT
M.1 SEWAGE TREATMENT
• One (1) EVAC MSP 150 Marine sewage treatment unit suitable for a daily sewage flow of 11840 litres in accordance with IMO and MED requirements
M.2 GARBAGE COMPACTION
• One (1) ENVIRO-PAK Model 4000C Roll Back Compactor, capacity 40 cu-ft. Compaction force 60,000 lbs