the row to be edited (for row information, see the output of the show security firewall ipv4 setup lan_wan command), you enter the security-config [firewall-ipv4-lan-wan-outbound] mode. You can then edit one keyword and associated parameter or associated keyword at a time in the order that you prefer. However, note that the setting of the action keyword determines which other keywords and parameters you can apply to a rule.
Step 1 Format
Mode security Step 2 Format
bandwidth_profile <profile name>
Mode security-config [firewall-ipv4-lan-wan-outbound]
security firewall ipv4 edit_rule lan_wan outbound <row id>
service_name {default_services <default service name> | {custom_services <custom service name>}
action {ALWAYS_BLOCK | ALWAYS_ALLOW |
BLOCK_BY_SCHEDULE_ELSE_ALLOW {schedule {Schedule1 | Schedule2 | Schedule3}} | ALLOW_BY_SCHEDULE_ELSE_BLOCK {schedule {Schedule1 | Schedule2 | Schedule3}}}
lan_users {{address_wise {ANY | SINGLE_ADDRESS {lan_user_start_ip <ipaddress>} | ADDRESS_RANGE {lan_user_start_ip <ipaddress>} {lan_user_end_ip <ipaddress>}} | group_wise <group name>}}
wan_users {{address_wise {ANY | SINGLE_ADDRESS {wan_user_start_ip <ipaddress>} | ADDRESS_RANGE {wan_user_start_ip <ipaddress>} {wan_user_end_ip <ipaddress>}} | group_wise <group name>}}
qos_profile <profile name>
log {NEVER | ALWAYS}
nat_ip {type {Auto | WAN1 | WAN2} | address <ipaddress>}
Keyword (might consist of two separate words)
Associated Keyword to Select or Parameter to Type
Description
Service name, action, and schedule service_name
default_services
ANY, AIM, BGP, BOOTP_CLIENT, BOOTP_SERVER, CU-SEEME:UDP, CU-SEEME:TCP, DNS:UDP, DNS:TCP, FINGER, FTP, HTTP, HTTPS,
ICMP-TYPE-3, ICMP-TYPE-4, ICMP-TYPE-5, ICMP-TYPE-6, ICMP-TYPE-7, ICMP-TYPE-8, ICMP-TYPE-9, ICMP-TYPE-10, ICMP-TYPE-11, ICMP-TYPE-13, ICQ, IMAP2, IMAP3, IRC, NEWS, NFS, NNTP, PING, POP3, PPTP, RCMD, REAL-AUDIO, REXEC, RLOGIN, RTELNET, RTSP:TCP, RTSP:UDP, SFTP, SMTP, SNMP:TCP, SNMP:UDP, SNMP-TRAPS:TCP,
SNMP-TRAPS:UDP, SQL-NET, SSH:TCP, SSH:UDP, STRMWORKS, TACACS, TELNET, TFTP, RIP, IKE, SHTTPD, IPSEC-UDP-ENCAP, IDENT, VDOLIVE, SSH, SIP-TCP, SIP-UDP, NFS-TCP, or RPC-TCP
Specifies the default service and protocol to which the firewall rule applies.
service_name custom_services
custom service name The custom service that you configure with the security services add
command and to which the firewall rule applies.
action ALWAYS_BLOCK, ALWAYS_ALLOW, BLOCK_BY_SCHEDULE_ELSE_ALLOW, or
ALLOW_BY_SCHEDULE_ELSE_BLOCK
Specifies the type of action to be enforced by the rule.
schedule Schedule1, Schedule2, or Schedule3
Specifies the schedule, if any, that applies to the rule.
LAN user addresses or LAN group and WAN user addresses lan_users address_wise ANY, SINGLE_ADDRESS, or
ADDRESS_RANGE
Specifies the type of LAN address. The address_wise and group_wise keywords are mutually exclusive.
lan_user_start_ip ipaddress The following two options are available:
• The IP address if the lan_users address_wise keywords are set to SINGLE_ADDRESS.
• The start IP address if the lan_users address_wise keywords are set to
ADDRESS_RANGE.
lan_user_end_ip ipaddress The end IP address if the lan_users address_wise keywords are set to ADDRESS_RANGE.
lan_users group_wise group name The name of the LAN group or LAN IP group. The LAN group name is either a default name (Group1, Group2, Group3, and so on) or a custom name that you specify with the net lan lan_groups edit <row id>
<newgroupname> command. The LAN IP group name is a name that you specify with the security services ip_group add command.
The address_wise and
group_wise keywords are mutually exclusive.
wan_users address_wise ANY, SINGLE_ADDRESS, or ADDRESS_RANGE
Specifies the type of WAN address.
The address_wise and
group_wise keywords are mutually exclusive.
wan_user_start_ip ipaddress The following two options are available:
• The IP address if the wan_users keyword is set to
SINGLE_ADDRESS.
• The start IP address if the wan_users keyword is set to ADDRESS_RANGE.
wan_user_end_ip ipaddress The end IP address if the wan_users keyword is set to ADDRESS_RANGE.
wan_users group_wise group name The name of the WAN IP group. The WAN IP group name is a name that you specify with the security services ip_group add command.
The address_wise and
group_wise keywords are mutually exclusive.
QoS profile, logging, bandwidth profile, and NAT IP address
qos_profile profile name The name of the QoS profile that you specify with the security services qos_profile add command.
log NEVER or ALWAYS Specifies whether logging is disabled or enabled.
Keyword (might consist of two separate words)
Associated Keyword to Select or Parameter to Type
Description