Run the BSC6900 MML command MOD UCELLHSDPA (CME single configuration: UMTS Cell Configuration Express > Cell Parameters > Cell HSDPA Parameters; CME batch modification

center: Modifying UMTS Cell Parameters in Batches) to set Code Number for HS-SCCH to 1.

The BSC6900 MML command MOD UCELLHSDPA (CME single configuration: UMTS Cell Configuration Express >

Cell Parameters > Cell HSDPA Parameters; CME batch modification center: Modifying UMTS Cell Parameters in Batches) fails to be executed when HSDPA is activated. Therefore, run the BSC6900 MML command DEA

UCELLHSDPA (CME single configuration: UMTS Cell Configuration Express > Cell Parameters > Cell HSDPA Parameters. Set ACTSTATUS to Deactivated; CME batch configuration: No supported) to deactivate HSDPA before

configuring this feature and run the BSC6900 MML command ACT UCELLHSDPA (CME single configuration: UMTS Cell

Configuration Express > Cell Parameters > Cell HSDPA Parameters. Set ACTSTATUS to Activated; CME batch

configuration: No supported) to reactivate HSDPA after configuring this feature.

The BSC6900 MML command MOD UCELLHSDPA (CME single configuration: UMTS Cell Configuration Express >

Cell Parameters > Cell HSDPA Parameters; CME batch modification center: Modifying UMTS Cell Parameters in Batches) fails to be executed when CELL-FACH enhancement is activated. Therefore, run the BSC6900 MML command

DEA UCELLEFACH (CME single configuration: UMTS Cell Configuration Express > Cell Parameters > Cell Enhanced FACH parameters. Set Validation indication to Deactivated; CME batch configuration: No supported) to

deactivate enhanced CELL-FACH before configuring this feature and Run the BSC6900 MML command ACT

UCELLEFACH (CME single configuration: UMTS Cell Configuration Express > Cell Parameters > Cell Enhanced FACH parameters. Set Validation indication to Activated; CME batch configuration: No supported) to reactivate

enhanced CELL-FACH after configuring this feature.

By default, the number of HS-SCCH codes for each cell is 4. If the default number is used, the HS-PDSCH can use only 14 SF16 codes. To enable the HS-PDSCH to use all 15 SF16 codes, run the BSC6900 MML command MOD

UCELLHSDPA (CME single configuration: UMTS Cell Configuration Express > Cell Parameters > Cell HSDPA Parameters; CME batch modification center: Modifying UMTS Cell Parameters in Batches) to set the value of Code

Number for HS-SCCH to 1.

2. Run the BSC6900 MML command MOD UCELLHSDPA (CME single configuration: UMTS Cell Configuration Express > Cell Parameters > Cell HSDPA Parameters; CME batch modification center: Modifying UMTS Cell Parameters in Batches) to set Allocate Code Mode to Manual(Manual) and Code Number for HS-PDSCH to 15.

 _{Verification Procedure}

1. Initialize UMTS monitoring on the BSC6900 LMT, as shown in Figure 6-1. Click Submit. A real-time monitoring window is displayed.

Issue 04 (2013-05-10) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

8-5

Figure 8-1 Cell Performance Monitoring

2. Check whether 15 SF16 codes are occupied by the HS-PDSCH in the Cell Performance Monitoring window.

Expected result: The HS-PDSCH occupies 15 SF16 codes.

 _{Deactivation Procedure}

This feature does not need to be deactivated.

Example

//Verifying 15 Codes per Cell

MOD UCELLHSDPA: CellId=1, HsScchCodeNum=1;

MOD UCELLHSDPA: CellId=1, AllocCodeMode=Manual, HsPdschCodeNum=15;

8.3 WRFD-01061018 Time and HS-PDSCH Codes Multiplex

8.3.1 When to Use Time and HS-PDSCH Codes Multiplex

None.

8.3.2 Information to Be Collected

None.

8.3.3 Feature Deployment

This section describes how to activate, verify, and deactivate the optional feature WRFD-01061018 Time and HS-PDSCH Codes Multiplex.

Prerequisites

 _{Dependencies on Hardware}

This feature does not have any special requirements for hardware.

 _{Dependencies on Other Features}

The configurations of the features on which this feature depends are complete. This feature depends on the feature WRFD-010610 HSDPA Introduction Package.

 _License

The license "HSDPA RRM package 1" and "HSDPA function" on the NodeB side has been activated. For details about how to activate the license, see License Management Feature Parameter.

Issue 04 (2013-05-10) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

8-6

Procedure

 _{Activation Procedure}

This feature does not need to be activated.

 _{Verification Procedure}

This feature does not need to be verified.

 _{Deactivation Procedure}

This feature does not need to be deactivated.

8.4 WRFD-01061009 HSDPA H-ARQ & Scheduling (MAX C/I, RR,

and PF)

8.4.1 When to Use HSDPA H-ARQ & Scheduling (MAX C/I, RR, and

PF

None.

8.4.2 Information to Be Collected

None.

8.4.3 Feature Deployment

This section describes how to activate, verify, and deactivate the optional feature WRFD-01061009 HSDPA H-ARQ & Scheduling (MAX C/I, RR, and PF).

Prerequisites

 _{Dependencies on Hardware}

This feature does not depend on the hardware.

 _{Dependencies on Other Features}

The configurations of the features on which this feature depends are complete. This feature depends on the feature WRFD-010610 HSDPA Introduction Package.

 _License

The license "HSDPA RRM package 1" and "HSDPA function" on the NodeB side has been activated. For details about how to activate the license, see License Management Feature Parameter

Description.

Procedure

 _{Activation Procedure}

HSDPA H-ARQ is activated automatically without any configuration.

This section describes how to set Max C/I, RR, and PF scheduling algorithms. For details on how to set the EPF scheduling algorithm, see the description of the feature WRFD-01061103 Scheduling based on EPF and GBR.

1. Run the NodeB MML command SET MACHSPARA (CME single configuration: NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm Parameters > MAC Parameters > MACHSPARA; CME batch modification center: Modifying Physical NodeB Parameters in Batches) to set the parameter Scheduling Method to MAXCI(Max C/I Algorithm), RR(Round Robin Algorithm) or PF(PF Algorithm).

Issue 04 (2013-05-10) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

8-7 1. Run the NodeB MML command LST MACHSPARA to query the settings of the parameter

Scheduling Method.

 _{Deactivation Procedure}

This feature does not need to be deactivated.

Example

//Activation procedure

SET MACHSPARA: LOCELL=0, SM=MAXCI; //Verification procedure

LST MACHSPARA: LOCELL=0;

8.5 WRFD-01061005 HSDPA Static Code Allocation and

RNC-Controlled Dynamic Code Allocation

8.5.1 When to Use HSDPA Static Code Allocation and

RNC-Controlled Dynamic Code Allocation

None.

8.5.2 Information to Be Collected

None.

8.5.3 Feature Deployment

This section describes how to activate, verify, and deactivate the optional feature WRFD-01061005 HSDPA Static Code Allocation and RNC-Controlled Dynamic Code Allocation.

Prerequisites

 _{Dependencies on Hardware}

This feature does not depend on the hardware.

 _{Dependencies on Other Features}

The feature WRFD-010610 HSDPA Introduction Package must be configured before this feature is activated.

 _License

The license "HSDPA RRM package 1" and "HSDPA function" on the NodeB side has been activated. For details about how to activate the license, see License Management Feature Parameter

Description.

Procedure

 _{Activation Procedure}

Run the BSC6900 MML command MOD UCELLHSDPA (CME single configuration: UMTS Cell Configuration Express > Cell Parameters > Cell HSDPA Parameters; CME batch modification center: Modifying UMTS Cell Parameters in Batches). In this step, set Allocate Code Mode to Manual or Automatic.

− If Allocate Code Mode is set to Manual, set Code Number for HS-PDSCH to specify the number of HS-PDSCH codes.

Issue 04 (2013-05-10) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

8-8

− If Allocate Code Mode is set to Automatic, set Code Max Number for HS-PDSCH to specify the maximum number of HS-PDSCH codes and set Code Min Number for HS-PDSCH to specify the minimum number of HS-PDSCH codes.

 _{Verification Procedure}