This table lists the IPL commands in alphabetical order by command syntax.
Syntax IPL Command Page
; Command Terminator 201
<ACK> First Data Entry Field, Select 99 <BEL> Error Code, Request 86
<BS> Warm Boot 112
<CAN> Clear All Data 93
<CR> Next Data Entry Field, Select 106 <DEL> Clear Data From Current Field 93
<DLE> Reset 87
<EM> Abort Print Job 86
<ENQ> Status Enquiry 89
<EOT> Postamble, Set 131
<ESC>L Label and Gap Length, Transmit 87 <ESC><SP> Start and Stop Codes (Code 39), Print 110 <ESC><SYN> Message Delay, Set 128 <ESC>c Emulation Mode, Enter 97 <ESC>C Advanced Mode, Select 91 <ESC>d Auto-Transmit 2, Enable 115 <ESC>D Field Decrement, Set 98 <ESC>e Auto-Transmit 3, Enable 115
<ESC>E Format, Select 101
<ESC>F Field, Select 97
<ESC>g Direct Graphics Mode, Select 96
<ESC>G Page, Select 108
<ESC>H Printhead Parameters, Transmit 109 <ESC>I Field Increment, Set 99 <ESC>j Auto-Transmit 1, Enable 115 <ESC>k Auto-Transmit 1, 2, and 3, Disable 115 <ESC>L Label and Gap Length, Transmit 87 <ESC>m Memory Usage, Transmit 105 <ESC>M Program Number, Transmit 110 <ESC>N Increment and Decrement, Disable 104 <ESC>O Options Selected, Transmit 107 <ESC>p Configuration Parameters, Transmit 94 <ESC>P Program Mode, Enter 109
Commands Listed by Syntax (continued)
Syntax IPL Command Page
<ESC>u User-Defined Characters, Transmit 111
<ESC>v Font, Transmit 100
<ESC>x Format, Transmit 103
<ESC>y Page, Transmit 108
<ESC>Z User-Defined Tables, Transmit 112
<ETB> Print 109
<FF> Form Feed 101
<FS> Numeric Field Separator 106 <GS> Alphanumeric Field Separator 92 <LF> Command Terminator 2 94 <NUL> Command Terminator 1 93 <RS> Quantity Count, Set 110 <SI>a Audible Alarm, Enable or Disable 114 <SI>A Control Panel Access Permission, Set 117 <SI>b Takeup Motor Torque, Increase 139 <SI>c Cutter, Enable or Disable 118 <SI>C Emulation or Advanced Mode on Power-Up 119 <SI>d Dark Adjust, Set 118 <SI>D End-of-Print Skip Distance, Set 120 <SI>e Media Fault Recovery Mode, Set 127 <SI>f Label Rest Point, Adjust 123 <SI>F Top of Form, Set 139 <SI>g Media Sensitivity, Select 127 <SI>h Printhead Loading Mode, Select 135 <SI>H Printhead Pressure, Set 136 <SI>i IBM Language Translation, Enable or Disable 122 <SI>I Number of Image Bands, Set 129 <SI>l Printer Language, Select 133 <SI>L Maximum Label Length, Set 126 <SI>N Amount of Storage, Define 114 <SI>O Online or Offline on Power-Up 130 <SI>p Pin 11/20 Protocol, Set 130 <SI>P Communication Port Configuration, Set 116 <SI>r Label Retract Distance, Set 124 <SI>R Label Retract, Enable or Disable 124 <SI>s Interlabel Ribbon Save, Enable or Disable 123
Commands Listed by Syntax (continued)
Syntax IPL Command Page
<SI>U Printhead Test Parameters, Set 136 <SI>W Label Width, Set 125 <SI>z Slash Zero, Enable or Disable 138 <SI>Z Ribbon Save Zones, Set 137
<SO> Cut 94
<SOH> Preamble, Set 131
<SUB> Data Shift - International Characters 94 <SYN> Intercharacter Delay, Set 122
<US> Batch Count, Set 93
<VT> Status Dump 88
A Ambient Temperature, Transmit 201 A or F Format, Create or Edit 180 b Border Around Human-Readable Text, Define 165 B Bar Code Field, Create or Edit 161 B Printhead Resistance Test, Begin 203
c Bar Code, Select Type 141
c Font Type, Select 178
c Graphic, Select 184
C Command Tables, Load 171
C Pitch Label, Print 203
d Field Data, Define Source 173
D Factory Defaults, Reset 202
D Field, Delete 172
e Data Source for Format in a Page, Define 172
E Format, Erase 182
f Field Direction, Define 175
f Formats, Print 202
g Pitch Size, Set 195
g User-Defined Characters and Graphics, Print 204 G Transmissive Sensor Value, Transmit 204 G User-Defined Character, Clear or Create 197 h Hardware Configuration Label, Print 202 h Height Magnification of Bar, Box, or UDC, Define 185 H Human-Readable Field, Create or Edit 187 i Interpretive Field, Enable or Disable 190
I Interpretive Field, Edit 189
Commands Listed by Syntax (continued)
Syntax IPL Command Page
K Dark Adjust 201
l Length of Line or Box Field, Define 190 L Label Path Open Sensor Value, Transmit 202 L Line Field, Create or Edit 191 m Format Position From Page, Delete 183 M Format Position in a Page, Assign 183 M Reflective Sensor Value, Transmit 204 N Current Edit Session, Save 172
o Field Origin, Define 175
O Format Offset Within a Page, Define 182 p Code 39 Prefix Character, Define 171
p Pages, Print 203
P Printhead Temperature Sensor Value, Transmit 203 q Format Direction in a Page, Define 181 Q Print Quality Label, Print 203 r Character Rotation or Bar Code Ratio, Define 168
R Program Mode, Exit 197
R Test and Service Mode, Exit 204
S Page, Create or Edit 194
s Page, Delete 195
S Printhead Resistance Values, Transmit 203 s Software Configuration Label, Print 204 t User-Defined Font Character, Create 198
t User-Defined Fonts, Print 205
T Bitmap User-Defined Font, Clear or Define 165 T Label Taken Sensor Value, Transmit 202
u Graphic or UDC, Define 184
U 12 Volt Supply Value, Transmit 201 U User-Defined Character Field, Create or Edit 197 v Print Line Dot Count Limit, Set 196 V Printhead Volt Supply Value, Transmit 204 w Width of Line, Box, Bar, or Character, Define 199
W Box Field, Create or Edit 166
x Bitmap Cell Width for Graphic or UDF, Define 164 X Character Bitmap Origin Offset, Define 167 y Bitmap Cell Height for Graphic or UDF, Define 162