IV.1
Structure Agnostic T1 Configuration
The following is an example of an eTEA configuration file used to configure a structure agnostic T1 PW.
Table IV–1 - Structure Agnostic T1 PW Configuration File Example
Type Length Value
(subtype)
Length Value Description
9 43 Pseudo wire configuration
1 2 1 PW index 1
2 1 18 Structure agonistic TDM over IP T1 PW 3 4 1.2.3.4 Peer’s IPv4 address
5 2 50000 Destination UDP port number 6 2 50001 Peer Destination UDP port number
7 4 T1-1 PW name
9 2 2 PW administratively down
10 1 0 Notifications not generated when the PW status changes
12 2 1 This PW uses TDM configuration table 1 16 3
16.1 1 2 This PW is associated with port 2
10 39 Common parameters for TDM configurations
1 2 1 TDM configuration table 1 2 2 192 Payload size is 192 bytes 3 1 0 Optional RTP header is not used 5 2 5 The jitter buffer is configured to be 5 msec 6 1 2 Disable payload suppression
7 2 10 Set the threshold to be 10 for exiting the loss of packet synchronization state
8 2 4 Set the threshold to be 4 for entering the loss of packet synchronization state
11 2 5 Window for calculating packet loss rate is set to 5 msec
12 1 5 Excessive loss occurs if the loss exceeds 5% 15 1 1 Severe loss occurs if the loss exceeds 1% 17 1 0xFF Fill pattern is defined as 0xFF
6 16 Digest value MD5 Digest
IV.2
Structure Agnostic E1 Configuration
The following is an example of an eTEA configuration file used to configure a structure agnostic E1 PW, with IPv6 addresses for the PW endpoints.
Table IV–2 - Structure Agnostic E1 PW Configuration File Example
Type Length Value
(subtype)
Length Value Description
9 55 Pseudo wire configuration
1 2 1 PW index 1
2 1 17 Structure agonistic TDM over IP E1 PW 4 16 2001::1.2.3.4 Peer’s IPv6 address
5 2 50000 Destination UDP port number 6 2 50001 Peer Destination UDP port number
7 4 E1-1 PW name
9 2 2 PW administratively down
10 1 0 Notifications not generated when the PW status changes
12 2 1 This PW uses TDM configuration table 1 16 3
16.1 1 2 This PW is associated with port 2
10 35 Common parameters for TDM configurations
1 2 1 TDM configuration table 1
2 2 256 Payload size is 256 bytes 3 1 0 Optional RTP header is not used 5 2 5 The jitter buffer is configured to be 5 msec 6 1 2 Disable payload suppression
7 2 10 Set the threshold to be 10 for exiting the loss of packet synchronization state
8 2 5 Window for calculating packet loss rate is set to 5 msec
12 1 5 Excessive loss occurs if the loss exceeds 5% 15 1 1 Severe loss occurs if the loss exceeds 1% 17 1 0xFF Fill pattern is defined as 0xFF
6 16 Digest value MD5 Digest
255 End of data marker
IV.3
Structure Aware 5xDS0 Configuration
The following is an example of an eTEA configuration file used to configure a structure aware 5xDS0.
Table IV–3 - Structure Aware nxDS0 PW Configuration File Example
Type Length Value
(subtype)
Length Value Description
9 53 Pseudo wire configuration
1 2 1 PW index 1
2 1 21 Structure aware PW (CESoPSN) 3 4 1.2.3.4 Peer’s IPv4 address
Type Length Value (subtype)
Length Value Description
5 2 50000 Destination UDP port number 6 2 50001 Peer Destination UDP port number
7 4 5DS0 PW name
9 2 2 PW administratively down
10 1 0 Notifications not generated when the PW status changes
12 2 1 This PW uses TDM configuration table 1 13 2 1 This PW uses CESoPSN configuration table 1 16 9
16.1 1 2 This PW is associated with port 2 16.2 4 0x1F The first five timeslots are used
10 39 Common parameters for TDM configurations
1 2 1 TDM configuration table 1 2 2 40 Payload size is 40 bytes 3 1 0 Optional RTP header is not used 5 2 5 The jitter buffer is configured to be 5 msec 6 1 2 Disable payload suppression
7 2 10 Set the threshold to be 10 for exiting the loss of packet synchronization state
8 2 4 Set the threshold to be 4 for entering the loss of packet synchronization state
11 2 5 Window for calculating packet loss rate is set to 5 msec
12 1 5 Excessive loss occurs if the loss exceeds 5% 15 1 1 Severe loss occurs if the loss exceeds 1% 17 1 0xFF Fill pattern is defined as 0xFF
13 16 CESoPSN parameters for TDM configurations
1 2 1 TDM CESoPSN configuration table 1 2 1 0xFF idle pattern is defined as 0xFF
3 1 1 Alarm indication signal on entire trunk is sent if packets are received with L flag set
4 1 1 When packets are received with the R flag set, remote alarm indication is set
5 1 0 Do nothing if received packet has L=0 and M=01
6 16 Digest value MD5 Digest
255 End of data marker
IV.4
Structure Aware 5xDS0 Configuration with CAS
The following is an example of an eTEA configuration file used to configure a structure aware 5xDS0.
Table IV–4 - Structure Aware nxDS0 PW Configuration File Example
Type Length Value
(subtype)
Length Value Description
9 53 Pseudo wire configuration
1 2 1 PW index 1
2 1 23 Structure aware PW (CESoPSN) with CAS 3 4 1.2.3.4 Peer’s IPv4 address
Type Length Value (subtype)
Length Value Description
5 2 50000 Destination UDP port number 6 2 50001 Peer Destination UDP port number
7 4 5DS0 PW name
9 2 2 PW administratively down
10 1 0 Notifications not generated when the PW status changes
12 2 1 This PW uses TDM configuration table 1 13 2 1 This PW uses CESoPSN configuration table 1 16 9
16.1 1 2 This PW is associated with port 2 16.2 4 0x1F The first five timeslots are used
10 39 Common parameters for TDM configurations
1 2 1 TDM configuration table 1 2 2 40 Payload size is 40 bytes 3 1 0 Optional RTP header is not used 5 2 5 The jitter buffer is configured to be 5 msec 6 1 2 Disable payload suppression
7 2 10 Set the threshold to be 10 for exiting the loss of packet synchronization state
8 2 4 Set the threshold to be 4 for entering the loss of packet synchronization state
11 2 5 Window for calculating packet loss rate is set to 5 msec
12 1 5 Excessive loss occurs if the loss exceeds 5% 15 1 1 Severe loss occurs if the loss exceeds 1% 17 1 0xFF Fill pattern is defined as 0xFF
13 25 CESoPSN parameters for TDM configurations
1 2 1 TDM CESoPSN configuration table 1 2 1 0xFF Fill pattern is defined as 0xFF
3 1 1 Idle pattern is sent if packets are received with L flag set
4 1 1 When packets are received with the R flag set, remote alarm indication is set
5 1 0 Do nothing if received packet has L=0 and M=01 7 1 5 TOS value for the CAS signaling traffic is 5 10 1 4 Application signaling idle interval is 4 sec 11 1 4 Application signaling interval is 4 msec
6 16 Digest value MD5 Digest
IV.5
Structure Aware T1 with RTP Configuration
The following is an example of an eTEA configuration file used to configure a structure aware T1 with optional RTP.
Table IV–5 - Structure Aware nxDS0 PW Configuration File Example
Type Length Value
(subtype)
Length Value Description
9 48 Pseudo wire configuration
1 2 1 PW index 1
2 1 21 Structure aware PW (CESoPSN) 3 4 1.2.3.4 Peer’s IPv4 address
5 2 50000 Destination UDP port number 6 2 50001 Peer Destination UDP port number
7 4 5DS0 PW name
9 2 2 PW administratively down
10 1 0 Notifications not generated when the PW status changes
12 2 1 This PW uses TDM configuration table 1 13 2 1 This PW uses CESoPSN configuration table 1
18 4 0xABCD SSRC value
10 35 Common parameters for TDM configurations
1 2 1 TDM configuration table 1 2 2 40 Payload size is 40 bytes 3 1 1 Optional RTP header is used
5 2 5 The jitter buffer is configured to be 5 msec
6 1 2 Disable payload suppression
7 2 10 Set the threshold to be 10 for exiting the loss of packet synchronization state
8 2 5 Window for calculating packet loss rate is set to 5 msec
12 1 5 Excessive loss occurs if the loss exceeds 5% 15 1 1 Severe loss occurs if the loss exceeds 1% 17 1 0xFF Fill pattern is defined as 0xFF
13 16 CESoPSN parameters for TDM configurations
1 2 1 TDM CESoPSN configuration table 1 2 1 0xFF idle pattern is defined as 0xFF
3 1 1 Alarm indication signal on entire trunk is sent if packets are received with L flag set
4 1 1 When packets are received with the R flag set, remote alarm indication is set
5 1 0 Do nothing if received packet has L=0 and M=01
6 16 Digest value MD5 Digest