Note
If you are going to connect the printer to your network, we recommend that you contact your system administrator prior to installation.
Before configuring the wireless settings
5IMPORTANT
If you have previously configured the wireless settings of the printer, you must reset the print server back to the default factory settings (see Restoring the network settings to factory default on page 117) and enable the WLAN setting from the control panel. See Enabling the wireless network using the control panel on this page.
Enabling the wireless network using the control panel 5
a
Make sure that the power cord is plugged in.b
Turn on your printer and wait until the printer is in the Ready state.c
Press any of the Menu buttons (+, -, OK or Back) to take the printer off-line.Ready
e
Press OK to move to the next menu level.LAN Wired
f
Press the + or - button to select WLAN.LAN WLAN
g
Press OK to move to the next level.WLAN TCP/IP
h
Press the + or - button to select WLAN Enable.WLAN
WLAN Enable
Wireless configuration for Macintosh® using the Brother automatic installer application
5
i
Press OK to move to the next level.WLAN Enable Off
j
Press the + or - button to select On.WLAN Enable On
k
Press OK.Accepted appears on the second line of the LCD.
WLAN Enable Accepted
The WLAN setting is enable.
Configure the wireless settings
5a
Turn on your Macintosh®.b
Put the supplied CD-ROM into your CD-ROM drive. Double-click the HL4040_4050_4070 icon on your desktop. Double-click the Start Here icon. Select your printer and the language.c
Click Install Printer Driver.5
d
Click Wireless Network users.e
Choose Wireless Setup and Driver Install or Wireless Setup Only, and then click Next.f
Read the Important Notice and check the box after you confirm this setting, and then click Next.Wireless configuration for Macintosh® using the Brother automatic installer application
5
g
Choose Manual and then click Next.h
For configuration, it is recommended that you temporarily connect your Brother wireless device (your printer) directly to a free port on your access point, hub or router using a network cable.If you can temporarily connect with a network cable:
Choose I’m able to temporarily connect my device to my access point with a network cable and then click Next. Go to i.
If you do not have a network cable or cannot temporarily connect the Brother wireless device to your access point:
Choose I’m not able to connect my device to my access point with a network cable and then click Next. Go to j.
5
i
Connect the Brother wireless device to your access point using a network cable and click Next. Go to n.j
If you choose This computer has wireless capability., check I am using an access point in infrastructure mode, and then click Next. Go to l.If you are using a wired computer, choose This computer uses a network cable to connect to the wireless network., you must configure the wireless settings from the control panel. Click Finish and see Using the Setup Wizard from the control panel on page 28.
If you have already completed the wireless settings and chose to install the printer driver in step e, click Next. Go to k.
Wireless configuration for Macintosh® using the Brother automatic installer application
5
k
Check the box after you confirm that you have completed the wireless settings, and then click Next.Go to Installing the printer driver on page 91.
l
You need to temporarily change your computer’s wireless settings. Follow the on-screen instructions.Make sure you take notes on all the settings such as SSID or channel of your computer. You will need them to return your computer back to its original wireless settings, and then click Next.
Item Record the current wireless computer settings
Communication mode: (Infrastructure / Ad-hoc) Channel: (1-14)
Network name: (SSID / ESSID)
Authentication method: (Open system / Shared key / WPA/WPA2-PSK / LEAP)
Encryption: (None / WEP / WPA / TKIP / AES/ CKIP) Encryption key:
5
m
To communicate with the un-configured wireless printer, temporarily change the wireless settings on your computer to match printer’s default settings shown on this screen. Check the box after you confirm these settings, and then click Next.Note
You can temporarily change the wireless settings on your computer, following the steps below:
1
Click the AirPort status icon and select Open Internet Connect....2
Click the Network tab to see the available wireless devices. You can see the Brother wireless print server in the Network option. Select SETUP.3
Your wireless network is connected successfully.n
Choose the printer you wish to configure, and click Next. If the list is blank, check if the access point and the printer are powered on, and then click Refresh.Note
The default Node name is “BRNxxxxxx” for the users that temporarily connect with a network cable, or
“BRWxxxxxx” for the users that connect without a network cable (where “xxxxxx” are the last six digits of Ethernet address).
Wireless configuration for Macintosh® using the Brother automatic installer application
5
o
The wizard will search for wireless networks available from your printer. Choose the access point you wish to associate the printer with, and then click Next.Note
• "SETUP" is the default SSID of the printer. Do not choose this SSID.
• If the list is blank, check that the access point has power and is broadcasting the SSID, and then see if the printer and the access point are within range for wireless communication. Then, click Refresh.
• If your access point is set to not broadcast the SSID you can manually add it by clicking the Add button.
Follow the on-screen instructions for entering the Name (SSID) and the Channel number.
p
If your network is not configured for Authentication and Encryption, the following screen will appear. To continue configuration, click OK and go to r.5
q
If your network is configured for Authentication and Encryption, the following screen will appear. When configuring your Brother wireless printer, you must ensure that it is configured to match theAuthentication and Encryption settings of your existing wireless network. Choose the
Authentication Method and Encryption Mode from the pull-downs in each setting box. Then enter the Network key and click Next.
Note
• If you want to setup more than WEP key1, click Advanced.
• If you do not know the Authentication or Encryption settings for network, contact your network administrator.
r
Click Next. The settings will be sent to your printer. The settings will remain unchanged if you click Cancel.Note
• If you want to manually enter the IP address settings of your printer, click Change IP Address and enter the necessary IP address settings for your network.
• The control panel settings will be automatically changed to WLAN when the wireless settings are sent to your printer.
Wireless configuration for Macintosh® using the Brother automatic installer application
5
s
Follow the on-screen instructions.For the users connected with a network cable for configuration:
Disconnect the network cable between your access point (hub or router) and the printer, and click Next.
For the users connected without a network cable for configuration:
Using the information you recorded in l, return the wireless settings of your computer back to their original settings. Check the box if you confirm this step, and then click Next or Finish.
You have completed the wireless setup. If you chose to install the printer driver in step e, Go to Installing the printer driver on page 91.
5
Configuration in Ad-hoc mode
5Note
If you are going to connect the printer to your network, we recommend that you contact your system administrator prior to installation.
Before configuring the wireless settings
5IMPORTANT
If you have previously configured the wireless settings of the printer, you must reset the print server back to the default factory settings (see Restoring the network settings to factory default on page 117) and enable the WLAN setting from the control panel. See Enabling the wireless network using the control panel on this page.
Enabling the wireless network using the control panel 5
a
Make sure that the power cord is plugged in.b
Turn on your printer and wait until the printer is in the Ready state.c
Press any of the Menu buttons (+, -, OK or Back) to take the printer off-line.Ready
e
Press OK to move to the next menu level.LAN Wired
f
Press the + or - button to select WLAN.LAN WLAN
g
Press OK to move to the next level.WLAN TCP/IP
h
Press the + or - button to select WLAN Enable.WLAN
WLAN Enable
Wireless configuration for Macintosh® using the Brother automatic installer application
5
i
Press OK to move to the next level.WLAN Enable Off
j
Press the + or - button to select On.WLAN Enable On
k
Press OK.Accepted appears on the second line of the LCD.
WLAN Enable Accepted
The WLAN setting is enable.
Configure the wireless settings
5a
Turn on your Macintosh®.b
Put the supplied CD-ROM into your CD-ROM drive. Double-click the HL4040_4050_4070 icon on your desktop. Double-click the Start Here icon. Select your printer and the language.c
Click Install Printer Driver.5
d
Click Wireless Network users.e
Choose Wireless Setup and Driver Install or Wireless Setup Only, and then click Next.f
Read the Important Notice and check the box after you confirm this setting, and then click Next.Wireless configuration for Macintosh® using the Brother automatic installer application
5
g
Choose Manual and then click Next.h
Choose I’m not able to connect my device to my access point with a network cable and then click Next.i
Choose This computer has wireless capability., and make sure I am using an access point in infrastructure mode is not checked. Click Next.5
j
You need to temporarily change your computer’s wireless settings. Follow the on-screen instructions.Make sure you take notes on all the settings such as SSID or channel of your computer. You will need them to return your computer back to its original wireless settings, and then click Next.
k
To communicate with the un-configured wireless printer, temporarily change the wireless settings on your computer to match printer’s default settings shown on this screen. Check the box after these settings, and then click Next.Note
You can temporarily change the wireless settings on your computer, following the steps below:
1
Click the AirPort status icon and select Open Internet Connect....Item Record the current wireless computer settings
Communication mode: (Infrastructure / Ad-hoc) Channel: (1-14)
Network name: (SSID / ESSID)
Authentication method: (Open system / Shared key / WPA/WPA2-PSK / LEAP)
Encryption: (None / WEP / WPA / TKIP / AES/ CKIP) Encryption key:
Wireless configuration for Macintosh® using the Brother automatic installer application