The IP parameters are configured with the IP submenu of the SETUP command. They control:
• General IP routing characteristics, using the SETUP/IP/GLOBAL submenu
• IP routing to a particular destination when RIP is disabled, using the SETUP/IP/
STATIC submenu.
Figure 2-18: SETUP/IP/GLOBAL and SETUP/IP/STATIC Paths Unit ID>
(main prompt)
Setup (SE)
IP
STATIC GLOBAL
► To configure the general IP routing characteristics:
1. Enter the menu sequence: SE ↵ IP ↵ GLOBAL 2. Set the Router to ENABLE
3. Change the other parameters from their default values, if desired.
SDM-9230>SE
IP> Route broadcast to end station (def:NO) ? IP> OSPF AS boundary router (def:NO) ?
IP> RIP AS boundary router (def:NO) ?
IP> IP Precedence for FR over IP (0-7,def:0) ?
► To configure a static IP address:
1. Enter the menu sequence: SE ↵ IP ↵ STATIC 2. Select an IP static entry number
3. Define the Destination address and Subnet mask 4. Define the Next hop to reach this destination, if required.
SDM-9230>SE
IP static entry number (1-200,def:1) ? IP STATIC 1> Valid (def:NO) ? YES
IP STATIC 1> Destination address (def:000.000.000.000) ? 128.130.0.2 IP STATIC 1> Subnet mask (number of bits) (0-24,def:0) ? 8
{255.255.000.000}
IP STATIC 1> Next hop (def:000.000.000.000) ? 128.129.0.2
Example addresses:
2.6.3 Configuring the Physical Link
The physical link provides LAN/WAN connectivity between a NetPerformer unit and:
• The IP cloud, using PPP (Figure 2-15)
• Another router, using PowerCell over IP (Figure 2-16)
• Another FRAD, using FRoIP (Figure 2-17).
The physical link may be:
• An Ethernet port
• A serial port
• A T1/E1 channel.
Figure 2-19: Static IP Address Scenario
Parameter Local Unit Remote Unit
IP Addr. of attached device: 128.128.0.1 128.130.0.1 IP Mask of attached device: 255.255.0.0 255.255.0.0
Default Gateway: 0.0.0.0 0.0.0.0
Default IP Address: 0.0.0.0 0.0.0.0
Default IP Mask: 0.0.0.0 0.0.0.0
LAN IP Address: 128.128.0.2 128.130.0.2
LAN IP Mask: 255.255.0.0 255.255.0.0
PVCR IP Address: 128.129.0.1 128.129.0.2
PVCR IP Mask: 255.255.0.0 255.255.0.0
Table 2-2 Examples of possible static IP addresses
The physical link is configured with the PORT or SLOT submenu of the SETUP command.
2.6.4 Ethernet Port
► To configure the Ethernet port:
1. Enter the menu sequence: SE ↵ PORT
2. Select ETH, ETH1 or ETH2 as the Port number Available values are product-dependent 3. Define the IP address and Subnet mask
Two IP addresses can be defined on later NetPerformer products.
4. Select the IP RIP version.
5. Change the other port parameters from their default values, if desired. Important parameters include:
• DHCP
• IGMP enable.
SDM-9230>SE SETUP
Item (BRIDGE/CALLER ID/CLASS/CUSTOM/FILTER/GLOBAL/HUNT/IP/IPX/MAP/PHONE/
PORT/PU/PPPOE/PPPUSER/PVC/REDUNDANCY/SCHEDULE/SLOT/USER/VLAN, Figure 2-20: SETUP/PORT & SETUP/SLOT/CHANNEL Paths
(IP Physical Link)
# ETH
Unit ID>
(main prompt)
Setup (SE)
Port (PO) Slot (SL)
Channel (CH)
PVCR PPP
PVCR PPP
Port number (ETH1/ETH2/CSL/1,def:ETH1) ? PORT ETH 1> Protocol (def:ETH AUTO) ? PORT ETH 1> LAN speed (mbps) (def:AUTO) ? PORT ETH 1> MAC address (def:000000000000) ? PORT ETH 1> DHCP (def:DISABLE) ?
PORT ETH 1> IP address 1 (def:000.000.000.000) ? 128.130.0.1 PORT ETH 1> Subnet mask 1 (number of bits) (0-24,def:0) ? 16 {255.255.255.000}
PORT ETH 1> IP address 2 (def:000.000.000.000) ?
PORT ETH 1> Subnet mask 2 (number of bits) (0-24,def:0) ? {000.000.000.000}
PORT ETH 1> Frame size (128-8192,def:1500) ? PORT ETH 1> IP RIP (def:V1) ?
PORT ETH 1> IP RIP TX/RX (def:DUPLEX) ? PORT ETH 1> OSPF (def:DISABLE) ?
PORT ETH 1> IGMP enable (def:NO) ?
PORT ETH 1> IP multicast active (def:NO) ? PORT ETH 1> IP multicast protocol (def:NONE) ? PORT ETH 1> NAT enable (def:NO) ?
PORT ETH 1> VLAN enable (def:NO) ? PORT ETH 1> IPX RIP (def:DISABLE) ? PORT ETH 1> IPX SAP (def:DISABLE) ?
PORT ETH 1> IPX network number (def:00000000) ? PORT ETH 1> IPX encapsulation (def:ETH 802.2) ?
PORT ETH 1> Physical connectivity detection (def:DISABLE) ?
For details on configuring an Ethernet port, refer to the LAN Connection and IP Networks module of this document series.
2.6.5 Built-in Serial Port
► To configure a built-in serial port as an IP link:
1. Enter the menu sequence: SE ↵ PORT 2. Select the Port number
3. Set the Protocol to:
• PPP, to access the IP cloud directly using PPP
• PVCR, for PowerCell over IP.
4. Change the other port parameters from their default values, if desired. Important parameters include:
Port number (ETH1/ETH2/CSL/1,def:1) ? PORT 1> Protocol (def:PPP) ?
PORT 1> Port Clocking (def:ASYNC) ? SYNC
PORT 1> Interface...DCE-V35 PORT 1> Clocking mode (def:INTERNAL) ?
PORT 1> Port speed (bps) (1200-6144000,def:56000) ? PORT 1> CRC encoding (def:NRZ) ?
PORT 1> Idle (def:FLAG) ?
PORT 1> Frame delay (ms) (def:0.0) ?
PORT 1> IP address (def:000.000.000.000) ? 128.130.0.2
PORT 1> Subnet mask (number of bits) (0-24,def:0) ? 16 {255.255.255.000}
PORT 1> IP RIP (def:V1) ?
PORT 1> IP RIP TX/RX (def:DUPLEX) ? PORT 1> NAT enable (def:NO) ? PORT 1> Silent (def:SEND REQUEST) ? PORT 1> LCP timeout (s) (1-255,def:3) ?
PORT 1> LCP retries, 255 = forever (0-255,def:255) ? PORT 1> Negotiate MRU (def:NO) ?
PORT 1> Use MRU proposed by peer (def:NO) ? PORT 1> Request Magic Number (def:YES) ?
PORT 1> Accept Magic Number Request (def:YES) ? PORT 1> Accept Addresses Old Negotiation (def:NO) ? PORT 1> Request IP-Address (def:NO) ?
PORT 1> Accept IP-Address Request (def:NO) ? PORT 1> Filter (def:ALL) ?
PORT 1> PPP dial index (def:NONE) ?
SDM-9230>SE PORT 1> Protocol (def:PPP) ? PVCR
PORT 1> Interface...DCE-V35 PORT 1> Clocking mode (def:INTERNAL) ?
PORT 1> Port speed (bps) (1200-6144000,def:56000) ? PORT 1> Mode (def:DEDICATED) ?
PORT 1> IP address (def:000.000.000.000) ? 128.130.0.3
PORT 1> Subnet mask (number of bits) (0-24,def:0) ? 16 {255.255.255.000}
PORT 1> IP RIP (def:V1) ?
PORT 1> IP RIP TX/RX (def:DUPLEX) ? PORT 1> OSPF (def:DISABLE) ?
PORT 1> IP multicast active (def:NO) ? PORT 1> IP multicast protocol (def:NONE) ? PORT 1> NAT enable (def:NO) ?
PORT 1> IPX RIP (def:DISABLE) ? PORT 1> IPX SAP (def:DISABLE) ?
PORT 1> IPX network number (def:00000000) ? PORT 1> Compression (def:YES) ?
PORT 1> Remote unit name (def:) ? CHICAGO-9230 PORT 1> Timeout (ms) (1000-30000,def:1000) ?
PORT 1> Number of retransmission retries (1-1000,def:100) ? PORT 1> Maximum number of voice channels (0-10000,def:10000) ?
PORT 1> Maximum Voice Channels If High Priority Data (0-10000,def:10000)
PORT 1> Cell Packetization (def:YES) ? PORT 1> Filter (def:ALL) ?
2.6.6 Dual Serial Interface Card
► To configure a serial port on the Dual Serial interface card as an IP link:
1. Enter the menu sequence: SE ↵ SLOT 2. Select the Slot number
3. Select the Channel number 4. Set the Protocol to:
• PPP, to access the IP cloud directly using PPP
• PVCR, for PowerCell over IP.
5. Change the other port parameters from their default values, if desired. Important parameters are as for a built-in serial port.
SDM-9230>SE
SLOT> Channel Number (201-202/ALL,def:202) ? 201 PORT 201> Protocol (def:PPP) ? PVCR
PORT 201> Interface...DCE-V35 PORT 201> Clocking mode (def:INTERNAL) ?
PORT 201> Port speed (bps) (1200-2048000,def:56000) ? PORT 201> Mode (def:DEDICATED) ?
PORT 201> IP address (def:000.000.000.000) ? 128.130.0.4 PORT 201> Subnet mask (number of bits) (0-24,def:0) ? 16 {255.255.255.000}
PORT 201> IP RIP (def:V1) ?
PORT 201> IP RIP TX/RX (def:DUPLEX) ? PORT 201> OSPF (def:DISABLE) ?
PORT 201> IP multicast active (def:NO) ? PORT 201> IP multicast protocol (def:NONE) ? PORT 201> NAT enable (def:NO) ?
PORT 201> IPX RIP (def:DISABLE) ? PORT 201> IPX SAP (def:DISABLE) ?
PORT 201> IPX network number (def:00000000) ? PORT 201> Compression (def:YES) ?
PORT 201> Remote unit name (def:) ?
PORT 201> Timeout (ms) (1000-30000,def:1000) ?
PORT 201> Number of retransmission retries (1-1000,def:100) ? PORT 201> Maximum number of voice channels (0-10000,def:10000) ? PORT 201> Maximum Voice Channels If High Priority Data (0-10000,def:10000) ?
PORT 201> Cell Packetization (def:YES) ? PORT 201> Filter (def:ALL) ?
2.6.7 T1/E1 Channel
► To configure a T1/E1 channel as an IP link:
1. Enter the menu sequence: SE ↵ SLOT 2. Select the Slot number
3. Enter CHANNEL at the Item prompt
4. Select the Channel number, e.g. 102, where the first digit indicates the slot and the last two digits indicate the channel
5. Set the Protocol to:
• PPP, to access the IP cloud directly using PPP
• PVCR, for PowerCell over IP.
6. Change the other port parameters from their default values, if desired. Important parameters are as for a built-in serial port.
SDM-9230>SE
SLOT> Channel Number (101-124/ALL,def:113) ? 114 PORT 114> Protocol (def:OFF) ? PPP
PORT 114> Timeslot (def:14) ?
PORT 114> Number of consecutive timeslots (1-11,def:1) ? PORT 114> DS0 speed (bps) (def:64000) ?
PORT 114> IP address (def:000.000.000.000) ? 128.130.0.5 PORT 114> Subnet mask (number of bits) (0-24,def:0) ? 16 {255.255.255.000}
PORT 114> IP RIP (def:V1) ?
PORT 114> IP RIP TX/RX (def:DUPLEX) ? PORT 114> NAT enable (def:NO) ? PORT 114> Silent (def:SEND REQUEST) ? PORT 114> LCP timeout (s) (1-255,def:3) ?
PORT 114> LCP retries, 255 = forever (0-255,def:255) ? PORT 114> Negotiate MRU (def:NO) ?
PORT 114> Negotiate MRU (NO/YES,def:NO) ? PORT 114> Use MRU proposed by peer (def:NO) ? PORT 114> Request Magic Number (def:YES) ?
PORT 114> Accept Magic Number Request (def:YES) ? PORT 114> Accept Addresses Old Negotiation (def:NO) ? PORT 114> Request IP-Address (def:NO) ?
PORT 114> Accept IP-Address Request (def:NO) ? PORT 114> Remote IP-Address (def:000.000.000.000) ? PORT 114> Filter (def:ALL) ?
For details on configuring a serial port or T1/E1 channel as an IP link, refer to the LAN Connection and IP Networks module of this document series.