FRONTIER 350/370 System Disk (A1)
GD1621
[ROM Replacement]
Replace the ROM on the CTL 20 circuit board with an adaptable ROM for FMPC.
1
Set the power switch to STANDBY, and turn OFF the built-in circuit breaker and the main supply.2
Remove the fourteen screws and then take off the printer control section cover.3
Remove the five screws and open the control CB bracket.4
Replace the ROM U16 (40 pins) on the CTL 20 circuit board with the adaptable ROM for FMPC.5
Close the control CB bracket, and then reinstall the printer control section cover.4.5
Replacing the ROM for Printer
Printer Control Section Cover Screws (14)
EZ783
Control Circuit
Board Bracket Screws (5)
EZ177
FMPC Adaptable ROM
4D005+*
(1) IEEE1394 Cable Preparation
Bind the bared part of the existing IEEE1394 cable connected between the printer (LP) and scanner (SP).
1
Remove the scanner rear cover by loosening the four screws and removing the fifteen screws.2
Remove the clamp screw and then disconnect the IEEE1394 cable from the scanner (SP).3
Remove the clamp from the cable.4
Bind the bared part of the cable with insulating tape.4.6
Connecting FMPC, FRONTIER, LAN Cable and Monitor Switcher
Screws(4)(Loosen) Screws(15)(Remove)
Scanner Rear Cover
EZ900 Clamp Screw IEEE1394 Cable MP004 Clamp Insulating Tape IEEE1394 Cable MP006
FMPC
SP
LP
(2) IEEE 1394 Cable Connection Preparations
1
Connect the Printer (LP) to the FMPC with the existing IEEE1394 cable (10m) that connected the Printer (LP) to the Scanner (SP).2
Connect the Scanner (SP) to the FMPC with the IEEE1394 cable (4.5m).IMPORTANT
Do not connect the two cables to the same board in the FMPC.
FMPC
Printer (LP)
Existing
IEEE1394 Cable (10m)
IEEE1394 Cable
(4.5m)
Scanner (SP)
FMPC
SP
LP
(3) Monitor Switcher Connections
Connect the FMPC, monitor switcher, and FRONTIER as follows.
It is recommended that the monitor switcher be installed under the monitor.
Scanner (SP)
Monitor Switcher Monitor
MP007
(4) Other Connections
Connect the FMPC, FRONTIER and the monitor switcher and then connect the LAN cable from the HUB to which the Imaging Controller is connected. as shown in the following connection diagram.
FRONTIER (SP)
Monitor Switcher
(Front)
(Back)
Main Control Unit (SP)
5
3
1
2
5
3
1
2
4
4
Power Supply
Keyboard
Mouse
Keyboard Cable from the SP Extension Cable for Keyboard
To Imaging Controller
HUB
IMPORTANTConnect the monitor’s power cable to the power supply directly. Do not connect the scanner’s power connector.
(5) Cable Routing
After the connections are completed, route the cables from FRONTIER as shown below.
Turn on the FMPC, then log on with the password “FRONTIER”.
IMPORTANT
If the FMPC Ver.1.0 is already installed, start up the FMPC while pressing the [Shift] key. (Start pressing the [Shift] key just when the Windows XP logo appears.)
4.7
Turning on FMPC
Mouse Cable
Serial Cable for Monitor Switcher LAN Cable
Cable Bracket Keyboard/Mouse Cable
from the front Keyboard Extention Cable Keyboard Cable
MP016
NMP010
Disable the 1394 network connection on SP side.
1
Select [Start] - [Control Panel], then click the [Network Connections].2
Right-click on the 1394 Connection whose status is “Enabled”, then set it to “Disabled”.IMPORTANT
Check the setting as follows: 1394 Connection on SP: Disabled 1394 Connection on LP: Enabled
3
Set to "Disabled" for another connection using the same procedure.The number of connection varies depending on your system.
4.8
Disabling Network Connection on SP Side
1
Press the scanner’s START switch to start up the FRONTIER.• The installer starts and the “[L-001] Simple Upgrade” screen appears.
2
Click the [OK] button.• The “Procedure Selection 1 [C-001]” screen appears.
3
Select “SE maintenance” and click the [Next] button.• The “Procedure Selection 2 [C-002]” screen appears.
4
Select “Update stand-alone scanner”, and click the [Next] button.5
In the confirmation dialog, click the [Yes] button.6
Click the [Next] button.4.9
[A1] Stand-alone Upgrade in SP [Ver.1.5 -> Ver.1.7] and
DI Print/Data Writing Software [C4/C5] Client Installation in SP
FMPC
• Copying starts.
7
Select “Inherit data from former version on HD”, and click the [Next] button.8
In the confirmation dialog, click the [OK] button.9
In the complete dialog, click the [OK] button.10
Remove the CD from the CD drive, then restart the scanner (SP).NOTE:
The connection error message may appear after restarting, but this causes no problems.
11
Insert the DI Print/Data Writing Software[C4/C5] installer CD into the CD drive of the FMPC, then start the installation.After restarting, the connection error message may appear, but this causes no problems.
1
Insert the FMPC driver CD into the CD-ROM, then in the “Device Drivers Disk [D-01]” dialog box, click the [OK] button. This completes the FMPC driver disk setup.If the driver disk is not started up automatically, run “N:\EZ171\Setup.exe.” (“N:\” varies depending on your system.)
2
When the FMPC driver disk setup is completed normally, the “Device Drivers Disk [D-02]” dialog box appears. Remove the driver disk from the CD-ROM drive, then click the [OK] button to shut down the system. After shutdown, turn on the FMPC.NOTE:
If the FMPC Ver.1.0 is already installed, start up the FMPC while pressing the [Shift] key.
(Start pressing the [Shift] key just when the Windows XP logo appears.)
4.10
IEEE1394 Driver Pre-installation
1
On the “Found New Hardware Wizard” screen, click the [Next] button.2
On the “Completing the Found...” screen, click the [Finish] button. This completes the installation of the driver for LP-5700 normally.3
On the Desktop, select [Start] - [Control Panel] - [System] - [Hardware] tab - [Device Manager], and then check if “1394 Client Device (For Scanner)” exists under “1394 Client Device”.1
Start up the printer (LP) in the ROM mode. During the countdown press [MENU - [<-] - [->] - [Enter] in this order, then check that the ROM Version is displayed on the panel, then check if the ROM Version is “(2.0-0x- 000)”.4.11
Installing IEEE1394 Driver for SP in FMPC
4.12
Starting-up LP in ROM Mode and Checking ROM Version (2.0-0x-000)
[ ROM Version ]
LP
FMPC
1
On the “Found New Hardware Wizard” screen, click the [Next] button.2
On the “Completing the Found...” screen, click the [Finish] button. This completes the installation of the driver for LP-5700 normally.3
On the Desktop, select [Start] - [Control Panel] - [System] - [Hardware] tab - [Device Manager], and then check if “1394 Client Device (For Printer)” exists under “1394 Client Device”.4.13
Installing IEEE1394 Driver for LP in FMPC
Install the FMPC software in the dedicated PC.
NOTE:
Before the installation, check if the ROM version is displayed in the operation panel in LP.
1
Insert the FMPC installer CD into the CD drive.2
The FMPC installer program is automatically started up.If the installer program is not started up, perform the following procedures.
(1) Move to [EZ171] folder in the CD drive. (2) Double-click [setup.exe].
3
In the “Procedure Selection (A-001)” screen, select “Re-installation”, then click the [Next] button.In case of updating from Ver.1.0 to Ver.2.0, select "User Versionup".
4
In the “Starting Re-installation (A-100)” dialog, click the [Yes] button.5
In the “Information (A-110)” dialog, click the [OK] button.4.14
FMPC [D20] Software Installation (Reinstall) with Printer's Backup FD
NMP012
6
On the “Printer Selection” screen, select “LP1500/LP2000”, then click the [Next] button.7
Installation is started.8
In the “FD Confirmation (A-117)” dialog, click the [Yes] button.NOTE:
In this case, select [NO] because the FMPC backup FD is not prepared yet.
9
In the “Inserting Backup FD (A-120)” dialog, click the [No] button.NOTE:
In this case, select [NO] because the FMPC backup FD is not prepared yet.
10
In the “Inserting Printer’s Backup FD (A-130)” dialog, click the [Yes] button.11
The “Information” dialog appears.12
Insert the Printer’s Backup FD for LP into the FD drive of the FMPC PC.13
Click the [OK] button.Click.
NMP014
14
On the “Input Source Selection [A-135]” screen, select [SP1500/SP2000], then click the [Next] button.15
Remove the FD from the FD drive.16
In the “Re-installation Completion(A-140)” dialog, click the [OK] button.17
In the “Setup Completion (A-150)” dialog, click the [OK] button.IMPORTANT
Do not restart the printer (LP). If it is restarted, all parameters are initialized.
18
Proceed to “4.15 DI Print/Data Writing Software Installation in FMPC”.NMP015
Install the DI Print/Data Writing [C4/C5] Client.
1
Replace the FMPC installer CD with the C4/C5 installer CD.2
Browse [Start] - [Shut Down], then select [Restart] to restart the PC.3
After the PC is restarted, the C4/C5 installer screen appears. Click the [Next] button.4
On the “Start Copying Files” screen, click the [Next] button.5
Installation is started.6
On the “...Wizard Complete” screen, select “Yes, I want to...”, then click the [Finish] button.4.15
DI Print/Data Writing Software [C4/C5] Client Installation in FMPC
NMP012
7
Remove the C4/C5 installer CD from the CDdrive.
8
On the “Install Shield Wizard Complete” screen, select “Yes, I will restart...”, then click the [Finish] button.
After the FMPC is restarted, the LP parameter downloading message I-2305 appears.
1
Open the "4 Setup and Maintenance" screen with “SE2” (Password : 7777).2
Select “1) System Condition Setup and Check” - “2) Installation Information Setup”, then set up the “Delivery Date” and “Setup Date”, and then click the [OK] button.NOTE:
If the settings are changed, restarting of SP is required to activate the new settings.
For the delivery and setup dates of printer, check “41F Installation Information Setup” in the scanner (SP).
NMP013
4.16
Installation Information Setup for FMPC
1
Restart the SP(Scanner), then open "Setup and Maintenance" - "System Condition Setup and Check" - "Installation Information Setup", and select "FMP Controller" as Output Device, then click the [OK] button.2
Select [350] or [370] for "System Name".(This selection is not required in case of SP-3000.) Default: 3703
Restart the SP.NOTE:
If the settings are changed, restarting of SP is required to activate the new settings.
To check the delivery and setup dates of printer, select “ON” in “Output Device”.
4.17
Output Device Setup for SP and Restarting SP
Copy the print size table from the SP to the FD by using the dedicated print size setting tool. Then, copying it to the FMPC.
(1) Copy Table to FD
1
Insert the print size setting tool FD into the FD drive of SP1500/2000, open the Explorer, then execute “PrintsizeSetTool.exe” in FD.2
When the FRONTIER model and System [A1] is proper, the following message appears. Click the [OK] button to start copying it to the system.3
Copying the data from SP to FD is started.4
After copying, the following message appears.(2) Copy Table from FD to FMPC
1
Insert the print size setting tool FD into the FD drive of FMPC, open the “Explorer”, then double- click “PrintSizeSetTool.exe” in FD drive.When the connections are properly done, the following message appears. To start copying, click the [OK] button.