The following table describes the messages that the diagnostic programs might generate and suggested actions to correct the detected problems. Follow the suggested actions in the order in which they are listed in the column.
089-801-xxx CPU CPU Stress Test
Aborted Internal program error.
1. Turn off and restart the system.
2. Make sure that the DSA code is at the latest level. For the latest level of DSA code, go to http://www.ibm.com/
support/docview.wss?uid=psg1SERV-DSA.
3. Run the test again.
4. Make sure that the system firmware is at the latest level. The installed firmware level is shown in the DSA event log in the Firmware/VPD section for this component. For more information, see “Updating the firmware” on page 297.
5. Run the test again.
6. Turn off and restart the system if necessary to recover from a hung state.
7. Run the test again.
8. If the failure remains, go to the IBM website for more troubleshooting information at http://www.ibm.com/
systems/support/supportsite.wss/
docdisplay?brandind=5000008&lndocid=SERV-CALL.
089-802-xxx CPU CPU Stress
Test
Aborted System resource availability error.
1. Turn off and restart the system.
2. Make sure that the DSA code is at the latest level. For the latest level of DSA code, go to
http://www.ibm.com/support/
docview.wss?uid=psg1SERV-DSA.
3. Run the test again.
4. Make sure that the system firmware is at the latest level. The installed firmware level is shown in the DSA event log in the Firmware/VPD section for this component. For the latest level of firmware, go to http://www.ibm.com/support/docview.wss?uid=psg1 MIGR-4JTS2T and select your system to display a matrix of available firmware.
5. Run the test again.
6. Turn off and restart the system if necessary to recover from a hung state.
7. Run the test again.
8. Make sure that the system firmware is at the latest level. The installed firmware level is shown in the DSA event log in the Firmware/VPD section for this component. For more information, see “Updating the firmware” on page 297.
9. Run the test again.
10. If the failure remains, go to the IBM website for more troubleshooting information at http://www.ibm.com/
systems/support/supportsite.wss/
089-901-xxx CPU CPU Stress Test
Failed Test
failure. 1. Turn off and restart the system if necessary to recover from a hung state.
2. Make sure that the DSA code is at the latest level. For the latest level of DSA code, go to http://www.ibm.com/
support/docview.wss?uid=psg1SERV-DSA.
3. Run the test again.
4. Make sure that the system firmware is at the latest level. The installed firmware level is shown in the DSA event log in the Firmware/VPD section for this component. For more information, see “Updating the firmware” on page 297.
5. Run the test again.
6. Turn off and restart the system if necessary to recover from a hung state.
7. Run the test again.
8. If the failure remains, go to the IBM website for more troubleshooting information at http://www.ibm.com/
systems/support/supportsite.wss/
docdisplay?brandind=5000008&lndocid=SERV-CALL.
166-801-xxx IMM IMM I2C Test Aborted IMM I2C test aborted:
the IMM returned an incorrect response length.
1. Turn off the system and disconnect it from the power source. You must disconnect the system from ac power to reset the IMM.
2. After 45 seconds, reconnect the system to the power source and turn on the system.
3. Run the test again.
4. Make sure that the DSA code is at the latest level. For the latest level of DSA code, go to http://www.ibm.com/
support/docview.wss?uid=psg1SERV-DSA.
5. Make sure that the IMM firmware is at the latest level.
The installed firmware level is shown in the DSA event log in the Firmware/VPD section for this component. For more information, see “Updating the firmware” on page 297.
6. Run the test again.
7. If the failure remains, go to the IBM website for more troubleshooting information at http://www.ibm.com/
systems/support/supportsite.wss/
docdisplay?brandind=5000008&lndocid=SERV-CALL.
166-802-xxx IMM IMM I2C Test Aborted IMM I2C test aborted:
the test cannot be completed for an unknown reason.
1. Turn off the system and disconnect it from the power source. You must disconnect the system from ac power to reset the IMM.
2. After 45 seconds, reconnect the system to the power source and turn on the system.
3. Run the test again.
4. Make sure that the DSA code is at the latest level. For the latest level of DSA code, go to http://www.ibm.com/
support/docview.wss?uid=psg1SERV-DSA.
5. Make sure that the IMM firmware is at the latest level.
The installed firmware level is shown in the DSA event log in the Firmware/VPD section for this component. For more information, see “Updating the firmware” on page 297.
6. Run the test again.
7. If the failure remains, go to the IBM website for more troubleshooting information at http://www.ibm.com/
systems/support/supportsite.wss/
docdisplay?brandind=5000008&lndocid=SERV-CALL.
166-803-xxx IMM IMM I2C Test Aborted IMM I2C test aborted:
the node is busy; try later.
1. Turn off the system and disconnect it from the power source. You must disconnect the system from ac power to reset the IMM.
2. After 45 seconds, reconnect the system to the power source and turn on the system.
3. Run the test again.
4. Make sure that the DSA code is at the latest level. For the latest level of DSA code, go to http://www.ibm.com/
support/docview.wss?uid=psg1SERV-DSA.
5. Make sure that the IMM firmware is at the latest level.
The installed firmware level is shown in the DSA event log in the Firmware/VPD section for this component. For more information, see “Updating the firmware” on page 297.
6. Run the test again.
7. If the failure remains, go to the IBM website for more troubleshooting information at http://www.ibm.com/
systems/support/supportsite.wss/
docdisplay?brandind=5000008&lndocid=SERV-CALL.
166-804-xxx IMM IMM I2C Test Aborted IMM I2C test aborted:
invalid command.
1. Turn off the system and disconnect it from the power source. You must disconnect the system from ac power to reset the IMM.
2. After 45 seconds, reconnect the system to the power source and turn on the system.
3. Run the test again.
4. Make sure that the DSA code is at the latest level. For the latest level of DSA code, go to http://www.ibm.com/
support/docview.wss?uid=psg1SERV-DSA.
5. Make sure that the IMM firmware is at the latest level.
The installed firmware level is shown in the DSA event log in the Firmware/VPD section for this component. For more information, see “Updating the firmware” on page 297.
6. Run the test again.
7. If the failure remains, go to the IBM website for more troubleshooting information at http://www.ibm.com/
systems/support/supportsite.wss/
docdisplay?brandind=5000008&lndocid=SERV-CALL.
166-805-xxx IMM IMM I2C Test Aborted IMM I2C test aborted:
invalid command for the given LUN.
1. Turn off the system and disconnect it from the power source. You must disconnect the system from ac power to reset the IMM.
2. After 45 seconds, reconnect the system to the power source and turn on the system.
3. Run the test again.
4. Make sure that the DSA code is at the latest level. For the latest level of DSA code, go to http://www.ibm.com/
support/docview.wss?uid=psg1SERV-DSA.
5. Make sure that the IMM firmware is at the latest level.
The installed firmware level is shown in the DSA event log in the Firmware/VPD section for this component. For more information, see “Updating the firmware” on page 297.
6. Run the test again.
7. If the failure remains, go to the IBM website for more troubleshooting information at http://www.ibm.com/
systems/support/supportsite.wss/
docdisplay?brandind=5000008&lndocid=SERV-CALL.
166-806-xxx IMM IMM I2C Test Aborted IMM I2C test aborted:
timeout while processing the command.
1. Turn off the system and disconnect it from the power source. You must disconnect the system from ac power to reset the IMM.
2. After 45 seconds, reconnect the system to the power source and turn on the system.
3. Run the test again.
4. Make sure that the DSA code is at the latest level. For the latest level of DSA code, go to http://www.ibm.com/
support/docview.wss?uid=psg1SERV-DSA.
5. Make sure that the IMM firmware is at the latest level.
The installed firmware level is shown in the DSA event log in the Firmware/VPD section for this component. For more information, see “Updating the firmware” on page 297.
6. Run the test again.
7. If the failure remains, go to the IBM website for more troubleshooting information at http://www.ibm.com/
systems/support/supportsite.wss/
docdisplay?brandind=5000008&lndocid=SERV-CALL.
166-807-xxx IMM IMM I2C Test Aborted IMM I2C test aborted:
out of space.
1. Turn off the system and disconnect it from the power source. You must disconnect the system from ac power to reset the IMM.
2. After 45 seconds, reconnect the system to the power source and turn on the system.
3. Run the test again.
4. Make sure that the DSA code is at the latest level. For the latest level of DSA code, go to http://www.ibm.com/
support/docview.wss?uid=psg1SERV-DSA.
5. Make sure that the IMM firmware is at the latest level.
The installed firmware level is shown in the DSA event log in the Firmware/VPD section for this component. For more information, see “Updating the firmware” on page 297.
6. Run the test again.
7. If the failure remains, go to the IBM website for more troubleshooting information at http://www.ibm.com/
systems/support/supportsite.wss/
docdisplay?brandind=5000008&lndocid=SERV-CALL.
166-808-xxx IMM IMM I2C Test Aborted IMM I2C test aborted:
reservation canceled or invalid reservation ID.
1. Turn off the system and disconnect it from the power source. You must disconnect the system from ac power to reset the IMM.
2. After 45 seconds, reconnect the system to the power source and turn on the system.
3. Run the test again.
4. Make sure that the DSA code is at the latest level. For the latest level of DSA code, go to http://www.ibm.com/
support/docview.wss?uid=psg1SERV-DSA.
5. Make sure that the IMM firmware is at the latest level.
The installed firmware level is shown in the DSA event log in the Firmware/VPD section for this component. For more information, see “Updating the firmware” on page 297.
6. Run the test again.
7. If the failure remains, go to the IBM website for more troubleshooting information at http://www.ibm.com/
systems/support/supportsite.wss/
docdisplay?brandind=5000008&lndocid=SERV-CALL.
166-809-xxx IMM IMM I2C Test Aborted IMM I2C test aborted:
request data was truncated.
1. Turn off the system and disconnect it from the power source. You must disconnect the system from ac power to reset the IMM.
2. After 45 seconds, reconnect the system to the power source and turn on the system.
3. Run the test again.
4. Make sure that the DSA code is at the latest level. For the latest level of DSA code, go to http://www.ibm.com/
support/docview.wss?uid=psg1SERV-DSA.
5. Make sure that the IMM firmware is at the latest level.
The installed firmware level is shown in the DSA event log in the Firmware/VPD section for this component. For more information, see “Updating the firmware” on page 297.
6. Run the test again.
7. If the failure remains, go to the IBM website for more troubleshooting information at http://www.ibm.com/
systems/support/supportsite.wss/
docdisplay?brandind=5000008&lndocid=SERV-CALL.
166-810-xxx IMM IMM I2C Test Aborted IMM I2C test aborted:
request data length is invalid.
1. Turn off the system and disconnect it from the power source. You must disconnect the system from ac power to reset the IMM.
2. After 45 seconds, reconnect the system to the power source and turn on the system.
3. Run the test again.
4. Make sure that the DSA code is at the latest level. For the latest level of DSA code, go to http://www.ibm.com/
support/docview.wss?uid=psg1SERV-DSA.
5. Make sure that the IMM firmware is at the latest level.
The installed firmware level is shown in the DSA event log in the Firmware/VPD section for this component. For more information, see “Updating the firmware” on page 297.
6. Run the test again.
7. If the failure remains, go to the IBM website for more troubleshooting information at http://www.ibm.com/
systems/support/supportsite.wss/
docdisplay?brandind=5000008&lndocid=SERV-CALL.
166-811-xxx IMM IMM I2C Test Aborted IMM I2C test aborted:
request data field length limit is exceeded.
1. Turn off the system and disconnect it from the power source. You must disconnect the system from ac power to reset the IMM.
2. After 45 seconds, reconnect the system to the power source and turn on the system.
3. Run the test again.
4. Make sure that the DSA code is at the latest level. For the latest level of DSA code, go to http://www.ibm.com/
support/docview.wss?uid=psg1SERV-DSA.
5. Make sure that the IMM firmware is at the latest level.
The installed firmware level is shown in the DSA event log in the Firmware/VPD section for this component. For more information, see “Updating the firmware” on page 297.
6. Run the test again.
7. If the failure remains, go to the IBM website for more troubleshooting information at http://www.ibm.com/
systems/support/supportsite.wss/
docdisplay?brandind=5000008&lndocid=SERV-CALL.
166-812-xxx IMM IMM I2C Test Aborted IMM I2C Test aborted: a parameter is out of range.
1. Turn off the system and disconnect it from the power source. You must disconnect the system from ac power to reset the IMM.
2. After 45 seconds, reconnect the system to the power source and turn on the system.
3. Run the test again.
4. Make sure that the DSA code is at the latest level. For the latest level of DSA code, go to http://www.ibm.com/
support/docview.wss?uid=psg1SERV-DSA.
5. Make sure that the IMM firmware is at the latest level.
The installed firmware level is shown in the DSA event log in the Firmware/VPD section for this component. For more information, see “Updating the firmware” on page 297.
6. Run the test again.
7. If the failure remains, go to the IBM website for more troubleshooting information at http://www.ibm.com/
systems/support/supportsite.wss/
docdisplay?brandind=5000008&lndocid=SERV-CALL.
166-813-xxx IMM IMM I2C Test Aborted IMM I2C test aborted:
cannot return the number of requested data bytes.
1. Turn off the system and disconnect it from the power source. You must disconnect the system from ac power to reset the IMM.
2. After 45 seconds, reconnect the system to the power source and turn on the system.
3. Run the test again.
4. Make sure that the DSA code is at the latest level. For the latest level of DSA code, go to http://www.ibm.com/
support/docview.wss?uid=psg1SERV-DSA.
5. Make sure that the IMM firmware is at the latest level.
The installed firmware level is shown in the DSA event log in the Firmware/VPD section for this component. For more information, see “Updating the firmware” on page 297.
6. Run the test again.
7. If the failure remains, go to the IBM website for more troubleshooting information at http://www.ibm.com/
systems/support/supportsite.wss/
docdisplay?brandind=5000008&lndocid=SERV-CALL.
166-814-xxx IMM IMM I2C Test Aborted IMM I2C test aborted:
requested sensor, data, or record is not present.
1. Turn off the system and disconnect it from the power source. You must disconnect the system from ac power to reset the IMM.
2. After 45 seconds, reconnect the system to the power source and turn on the system.
3. Run the test again.
4. Make sure that the DSA code is at the latest level. For the latest level of DSA code, go to http://www.ibm.com/
support/docview.wss?uid=psg1SERV-DSA.
5. Make sure that the IMM firmware is at the latest level.
The installed firmware level is shown in the DSA event log in the Firmware/VPD section for this component. For more information, see “Updating the firmware” on page 297.
6. Run the test again.
7. If the failure remains, go to the IBM website for more troubleshooting information at http://www.ibm.com/
systems/support/supportsite.wss/
docdisplay?brandind=5000008&lndocid=SERV-CALL.
166-815-xxx IMM IMM I2C Test Aborted IMM I2C test aborted:
invalid data field in the request.
1. Turn off the system and disconnect it from the power source. You must disconnect the system from ac power to reset the IMM.
2. After 45 seconds, reconnect the system to the power source and turn on the system.
3. Run the test again.
4. Make sure that the DSA code is at the latest level. For the latest level of DSA code, go to http://www.ibm.com/
support/docview.wss?uid=psg1SERV-DSA.
5. Make sure that the IMM firmware is at the latest level.
The installed firmware level is shown in the DSA event log in the Firmware/VPD section for this component. For more information, see “Updating the firmware” on page 297.
6. Run the test again.
7. If the failure remains, go to the IBM website for more troubleshooting information at http://www.ibm.com/
systems/support/supportsite.wss/
docdisplay?brandind=5000008&lndocid=SERV-CALL.
166-816-xxx IMM IMM I2C Test Aborted IMM I2C
1. Turn off the system and disconnect it from the power source. You must disconnect the system from ac power to reset the IMM.
2. After 45 seconds, reconnect the system to the power source and turn on the system.
3. Run the test again.
4. Make sure that the DSA code is at the latest level. For the latest level of DSA code, go to http://www.ibm.com/
support/docview.wss?uid=psg1SERV-DSA.
5. Make sure that the IMM firmware is at the latest level.
The installed firmware level is shown in the DSA event log in the Firmware/VPD section for this component. For more information, see “Updating the firmware” on page 297.
6. Run the test again.
7. If the failure remains, go to the IBM website for more troubleshooting information at http://www.ibm.com/
7. If the failure remains, go to the IBM website for more troubleshooting information at http://www.ibm.com/