VALVE AND SHAFT SPEED SENSOR For voltage or current control of trolling valve.
Jumper set to pull Troll On to (–) negative battery.
(LABEL 3)
• For use with Twin Disc and Reintjes gears
MOUNTING
MSCS II The MSCS II system does not use the MJB for power distribution and therefore requires some terminations to be made by the customer . Refer to Fig . 03 for a typical layout of the cables .
Fig. 03 MSCS II Dual Engine example
The MSCS II system does not use the MJB for power distribution and therefore requires the customer to supply Power, Ground and Keyswitch to the engine 70-pin customer connector and the PCP . Fig . 04 shows a typical example for a dual engine application . The batteries, circuit breakers, terminal blocks, wires, and switches are supplied by the customers .
Fig 05 shows a typical example of customer terminations for cable
337-0971 . The batteries, circuit breakers, terminal blocks, wires, and switches
Fig. 04 MSCS II
Dual Engine Customer Wiring Example: Power, Ground, and Keyswitch
Fig. 05 MSCS II
Dual Engine PCP Power Termination Cable 337-0971
Marine Junction Box –
Twin Engine 225-6123 Twin Engine Marine Junction Box
Marine Junction Box –
Single Engine 225-6122 Single Engine Marine Junction Box
Trunk Harness 225-6116 Made-to-length harness that connects the ECU customer connector to the MJB . One cable is required per engine . Length 225-6117 Start Stop Control Panel 217-3865 Start/stop panel with keyswitch, remote
shutdown switch, and warning and diagnostic lamps . Requires 210-8772 or 210-8773 (for use with 217-8191) gaskets
Sync Switch Panel 217-8191 Sync switch panel, sync and slow vessel mode functions . Requires 217-3865 and 210-8773 . Keyswitch/Alarm 226-3423 Keyswitch/alarm breakout panel – connects
Breakout Panel keyswitch, PCP alarm, remote shutdown
switch, remote start, diagnostic lamp, warning lamp, minus battery, and plus battery . Requires 226-0361 or OEM supplied wiring .
Keyswitch/Alarm 226-0361 Made-to-length cable that connects the
Breakout Panel Wiring keyswitch/alarm breakout panel to the
MJB . Length 226-0362
Marine Power Display 267-8623 MPD display with application code 259-2171
Marine Power Display 259-2170 MPD display without application code (blank display)
Marine Power Display 291-4310 MPD mounting kit Mounting Kit
Marine Power Display Bracket 208-0590 MPD mounting kit – gimbal mount 6-Pin Termination Resistor 208-0432 Termination resistor
6-Pin Tee Connector 221-9506 Six-pin tee connector – connects components and drop harnesses into the CAN or J1939 data link harness
MPD Drop Harness 225-6112 Made-to-length MPD drop harness to connect the MPD display into the J1939 data link trunk harness . Length 225-6114 . MAPD Interface Module 274-8068 Used to convert the J1939 into the gauge
data link .
MAPD Harness 212-8259 Cable to connect from the 3-pin tee to the 6-pin MAPD interface module connector .
Part Name Part Number Description
3-pin Termination Resistor 174-3016 Termination resistor to be used with the 3-pin tee (133-0970) . Not used in MSCS . 3-pin Tee 133-0970 3-pin tee connector to be used with 3-pin
termination resistor . Not to be used with MSCS . MAPD Harness Extension 3 ft . 212-8258 MAPD 3-foot extension harness
MAPD Harness Extension 5 ft . 212-8257 MAPD 5-foot extension harness MAPD Harness Extension 30 ft . 212-8256 MAPD 30-foot extension harness
MAPD Harness 221-0777 Cable to connect from the 3-pin tee to the 6-pin MAPD interface module connector . Cable has 3E3382 receptacle .
MAPD Drop Harness 227-3514 Made-to-length MAPD drop harness for MSCS . To connect the MAPD display into the J1939 trunk harness . Length 227-3515 . Messenger Display 201-8867 Marine Messenger display
J1939 Trunk Harness 225-6107 Made-to-length J1939 display trunk harness . Requires the 6-pin tee (221-9506) .
Length 229-0292 . Engine Vision Display 212-7481 163-3972 mounting kit
163-3973 data cable
163-3974 power supply cable
EVIM 225-0774 Engine Vision Interface Module
GPSIM 130-6191 GPS Interface Module
Diode Block 7C2668 Used to connect multiple switched battery
wires to the EVIM and Engine Vision display Cat Data Link Harness 225-6118 Made-to-length CDL harness to connect from
for MSCS the MJB to the Engine Vision display or a
remote service tool connector . Length 225-6119 . Custom Panel Wiring 225-6102 Made-to-length custom panel harness . Connects
the custom breakout panel to the MJB .
Part Name Part Number Description
Part Name Part Number Description
PCP Power Cable 226-0369 Made-to-length power cable . Connects power from the MJB to the PCP . Length 226-0370 . PCP throttle and 226-0367 Made-to-length cable that connects the PCP J1939 data link cable into the J1939 data link and connects the throttle
signals to the MJB . Length 226-0368 .
Backup Panel 219-8023 Backup panel for MSCS
Backup Panel Wiring – 226-0363 Provides made-to-length terminated cable One Backup Control Station wiring harness for a single control station
on the master control station data link, control station data link, or the backup control station data link . Proprietary CAN data link trunk harness . Length 226-0364 .
Backup Panel Wiring – 225-6107 Provides made-to-length non-terminated
Two or more Backup cable wiring harness for multiple controls
Control Stations on the control station data link or the backup
control station data link .
Proprietary CAN data link trunk harness . Length 229-0292 .
PCP to Tee Wiring Harness 226-0365 PCP station drop into the CAN proprietary data link for control station or backup station data links . Cable has a fixed length of 2 ft .
Station Drop Harness 226-0366 Control station drop harness into proprietary CAN data link . Backup control station drop harness into backup control station data link . Cable has a fixed length of 2 ft .
Dual Control Harness 226-3419 Used to connect a single slimline throttle
Assembly control head and a single slimline gear
control head to the control station
processor . Cable has a fixed length of 2 ft . Control Station Processor (CSP) 219-8021 Interfaces with the slimline control head or
sidemount control head and the button panel . Slimline Control Head – Dual 223-8214 Combined throttle and gear in one lever . Function (Brushed Aluminum) Control has a brushed aluminum base and
straight lever arm .
Slimline Control Head – 223-8211 Lever actuation only controls engine speed .
Throttle Lever Control has a brushed aluminum base and
(Brushed Aluminum) straight lever arm .
Slimline Control Head – Gear 223-8213 Lever actuation controls gear position . Lever (Brushed Aluminum) Control has a brushed aluminum base and
Part Name Part Number Description
Slimline Control Head – 223-8219 Combined throttle and gear in one lever . Dual Function (Black Chrome) Control has a black chrome base and
straight lever arm .
Slimline Control Head – Throttle 223-8216 Lever actuation only controls engine speed . Lever (Black Chrome) Control has a black chrome base and straight
lever arm .
Slimline Control Head – Gear 223-8218 Lever actuation controls gear position . Control Lever (Black Chrome) has a black chrome base and straight lever arm . Port Sidemount Control Head 229-3689 Sidemount control head for port controls .
Mounts under dash, gear and throttle combined OEM to supply lever .
Shaft Kit 296-7828 Contains: 1 – shaft for side mount control head, 2 – set screws, 1 – nylon bearing
Starboard Sidemount 229-3690 For starboard controls . Mounts under dash, gear
Control Head and throttle combined OEM to supply lever .
Integrated Control Head – 219-8022 Chrome ICH Chrome
Integrated Control Head – 220-2313 Black chrome ICH Black Chrome
Integrated Control Head – Gold 220-2315 Gold ICH
ICH Cat Decal 276-4054 Round decal on the side of ICH
Chrome Bezel Kit 276-4055 Replacement parts for the chrome bezel on the ICH or button panel .
Black Chrome Bezel Kit 287-0564 Replacement parts for the black chrome bezel on the ICH or button panel .
Gold Bezel Kit 287-0563 Replacement parts for the gold bezel on the ICH or button panel .
Slimline Control Head – Dual 223-8204 Combined throttle and gear in one lever . Function (Brushed Aluminum) Control has a brushed aluminum base and
right slant handle .
Slimline Control Head – Gear 223-8201 Lever actuation controls gear position . Lever (Brushed Aluminum) Control has a brushed aluminum base and
right slant handle .
Slimline Control Head – Throttle 223-8220 Lever actuation only controls engine speed . Lever (Brushed Aluminum) Control has a brushed aluminum base and
left slant handle .
Slimline Control Head – Gear 223-8221 Lever actuation controls gear position . Lever (Brushed Aluminum) Control has a brushed aluminum base and
left slant handle .
Slimline Control Head – Dual 223-8208 Combined throttle and gear in one lever . Function (Black Chrome) Control has a black chrome base and
right slant handle .
Slimline Control Head – Dual 223-8225 Combined throttle and gear in one lever . Function (Black Chrome) Control has a black chrome base and
left slant handle .
Slimline Control Head – Throttle 223-8205 Lever actuation only controls engine speed .
Lever (Black Chrome) Control has a black chrome base and right
slant handle .
Slimline Control Head – Gear 223-8218 Lever actuation controls gear position .
Lever (Black Chrome) Control has a black chrome base and right
slant handle .
Master Control Station Harness 226-0363 Provides made-to-length terminated cable wiring harness for a single control station on the master control station data link, control station data link, or the backup control station data link .
Proprietary CAN data link trunk harness . Length 226-0364 .
Control Station Wiring – One 226-0363 Provides made-to-length terminated cable Control Station on Data Link wiring harness for a single control station on
the master control station data link, control station data link, or the backup control station data link .
Proprietary CAN data link trunk harness . Length 226-0364 .
Control Station Wiring – 225-6107 Provides made-to-length non-terminated Two or more Control Stations cable wiring harness for multiple controls
on the control station data link or the backup control station data link . Proprietary CAN data link trunk harness . Length 229-0292 .
Part Name Part Number Description
Button Panel – Chrome 221-9507 Button panel to interface with the control station processor .
Button Panel – Black Chrome 224-9873 Button panel to interface with the control station processor .
Button Panel – Gold 224-9874 Button panel to interface with the control station processor .
Button Panel Wiring 226-0411 Provides made-to-length wiring to connect the button panel to the CSP .
Length 226-0412 .
PCP to Gear Harness 226-0371 Made-to-length wiring harness to connect the PCP to the marine gear shift solenoids . Length 231-6615 .
Electronic Troll Processor 256-4883 Provides the interface to the marine
(ETP) transmission electronic trolling valve for the
PCP to control trolling functions .
Troll Harness 226-0417 For use with ZF 350, 2000, 1900/2500 and 4500… 750 series gears
Troll Harness 243-4211 For use with Twin Disc, Reintjes, ZF2000, 1900/2500, 4500… 750
Troll Harness 243-4212 For use with Twin Disc, Reintjes gears . ETP Shaft Speed Sensor 226-3424 ETP Shaft speed pick-up .
Shaft Speed Pickup Band 226-0413 Provides a custom length band for detection of transmission shaft speed .
Length 226-0414 .
ETP Data Link Harness 226-3414 ETP drop into the display J1939 data link . Cable has a fixed length of 2 ft .
Wing Station Control 255-8006 Panel mount wing station control Auxiliary Pressure 275-2077 2-inch gauge/ 0-500 psi
Auxiliary Temperature 275-2078 2-inch gauge/ -40-120° F
Boost Pressure 275-2079 2-inch gauge/ 0-50 psi
Part Name Part Number Description
Fuel Pressure 275-2086 2-inch gauge/ 0-125 psi
Fuel Pressure 275-2087 3-inch gauge/ 0-125 psi
Fuel Rate 275-2088 2-inch gauge/ 0-80 gph
Fuel Rate 275-2089 2-inch gauge/ 0-50 gph
Fuel Rate 275-2090 2-inch gauge/ 0-200 gph
Fuel Rate 275-2091 3-inch gauge/ 0-200 gph
Fuel Temperature 275-2092 2-inch gauge/ 0-250° F
Fuel Temperature 275-2093 3-inch gauge/ 0-250° F
Inlet Manifold Temperature 275-2094 2-inch gauge/ 0-250° F Inlet Manifold Temp . 275-2095 3-inch gauge/ 0-250° F
Oil Pressure 275-2096 2-inch gauge/ 0-100 psi
Oil Pressure 275-2097 3-inch gauge/ 0-100 psi
Oil Temperature 275-2098 2-inch gauge/ 0-250° F
Oil Temperature 275-2099 3-inch gauge/ 0-250° F
Percent Load 275-2100 2-inch gauge/ 0-100%
Percent Load 275-2101 3-inch gauge/ 0-100%
Speed 275-2102 3-inch gauge/ 0-60 knots
Tachometer w/LCD 275-2103 3-inch gauge/ 0-4000 rpm Tachometer w/LCD 275-2104 3-inch gauge/ 0-3000 rpm Tachometer w/LCD 275-2105 3-inch gauge/ 0-3600 rpm Transmission Oil Pressure 275-2106 2-inch gauge/ 0-500 psi Transmission Oil Pressure 275-2107 3-inch gauge/ 0-500 psi Transmission Oil Temperature 275-2108 2-inch gauge/ 0-250° F Transmission Oil Temperature 275-2109 3-inch gauge/ 0-250° F
Volt 275-2110 2-inch gauge/ 9-32 VDC
Volt 275-2111 3-inch gauge/ 9-32 VDC
Volt 275-2112 2-inch gauge/ 0-16 VDC
Tachometer w/LCD 262-4919 3-inch gauge/ 0-3600 rpm (white face)
Speed 262-4920 3-inch gauge/ 0-60 knots (white face)
Oil Pressure 262-4921 2-inch gauge/ 0-100 psi (white face) Engine Coolant 262-4922 2-inch gauge/ 0-250° F (white face)
Volt 262-4923 2-inch gauge/ 0-16 VDC (white face)
Part Name Part Number Description
Volt 262-4924 2-inch gauge/ 9-32 VDC (white face) Transmission Oil Pressure 262-4925 2-inch gauge/ 0-500 psi (white face) Transmission Oil Temperature 262-4926 2-inch gauge/ 0-250° F (white face)
Fuel Level 262-4927 2-inch gauge/ 0 -4/4 (white face)
MAPD Panel 214-1731 Includes a start/stop keyswitch, emergency stop button, warning lamp, diagnostic lamp, and a dimmer button . The gauges include 3”
tachometer, 2” coolant temperature, 2” oil pressure, 2” voltmeter, and 2” inlet manifold temperature . They have a black face and black chrome bezel . The panel has capacity for two additional 2” gauges .
PL1000T 256-7511 PL1000T, 279-6664 software,
258-4550 PL1000T
PL1000T Harness Assembly 270-1732 Harness assembly for PL1000T
PL1000E 256-7512 PL1000E, 256-6806 software,
258-4548 PL1000E
PL1000E Cable 228-6559 Cable assembly for PL1000E
PL1000T Harness Assembly 276-0785 Harness assembly for PL1000T Twisted Pair Cat Data
Link Cable 143-5018 Twisted pair CDL wire (pink and white)
J1939 Cable 153-2707 J1939 standard wire (yellow/green and
shield)
Keyswitch 110-7887 Stand-alone keyswitch . For use with key 5P8500 .
ZF Gear Connector 1Q5094 Inline connector
ZF Gear Connector 8T9605 Right angle connector
6-Pin Deutsch Receptacle Kit 102-8805 6-pin receptacle to connect to the PCP gear harness . Includes 3E3382 receptacle and 3E3383 wedge .
4-Pin Deutsch Receptacle Kit 102-8804 4-pin receptacle to connect to the ETP to troll valve cable . Includes 3E3376 receptacle and
Part Name Part Number Description