The following example shows sample output from the show controllers TenGigE bert command:
RP/0/RP0/CPU0:router# show controllers TenGigE 0/6/0/2 bert BERT status for TenGigE0/6/0/2:
BERT State : DISABLED
Cisco IOS XR Interface and Hardware Component Command Reference for the Cisco CRS Router, Release 5.1.x
OL-30349-01 47
Ethernet Interface Commands on the Cisco IOS XR Software
show controllers (Ethernet)
Test Pattern : None test pattern
Time Remaining : 0
Time Interval : 0
The following example shows sample output from the show controllers TenGigE bert command that is unsupported on the Cisco CRS 14-Port or Cisco CRS 20-Port 10-Gigabit Ethernet LAN/WAN-PHY Interface Module:
RP/0/RP0/CPU0:router# show controllers TenGigE 0/1/0/0 bert Thu Oct 7 18:26:01.108 EST
Command not supported on this interface
The following example shows sample output from the show controllers TenGigE control command for the Cisco CRS 14-Port 10-Gigabit Ethernet LAN/WAN-PHY Interface Module:
RP/0/RP0/CPU0:router# show controllers TenGigE 0/1/0/0 control Thu Oct 7 18:26:11.815 EST
Management information for interface TenGigE0/1/0/0:
Port number: 0 Bay number: 0
Interface handle: 0x1180200 Config:
Auto-negotiation: Configuration not supported (Off) Carrier delay (up): Not configured
Carrier delay (down): Not configured
Speed: Configuration not supported (10Gbps) Duplex: Configuration not supported (Full Duplex) Flow Control: Not configured (None)
IPG: Not configured (standard (12)) Loopback: Not configured (None) MTU: Not configured
Bandwidth: Not configured
BER-SD Threshold: Configuration not supported BER-SD Report: Configuration not supported BER-SF Threshold: Configuration not supported BER-SF Report: Configuration not supported
BER-SF Signal Remote Failure: Configuration not supported Driver constraints:
Min MTU: 64 bytes Max MTU: 9600 bytes Max speed: 10Gbps Interface type: TenGigE Management interface: No Promiscuous mode: Yes
Default carrier delay up (auto-neg on): 0 ms Default carrier delay down (auto-neg on): 0 ms Default carrier delay up (auto-neg off): 0 ms Default carrier delay down (auto-neg off): 0 ms Allowed config mask: 0x27b
Cached driver state:
MTU: 1522 bytes
Burnt-in MAC address: 0014.f294.6776 Operational carrier delay:
Carrier delay (up): 0 ms Carrier delay (down): 0 ms Bundle settings:
Aggregated: No
Bundle MTU: 1514 bytes
Bundle MAC address: 0014.f294.6776 Port FSM state:
Port is disabled, due to an admin down condition.
Complete FSM state:
Admin down Bundle admin up Client admin up
Ethernet Interface Commands on the Cisco IOS XR Software show controllers (Ethernet)
Client admin tx not disabled Port disabled
Port tx disabled Hardware link down
IDB interface state information:
IDB bundle admin up IDB client admin up IDB client tx admin up IDB error disable not set 0 Unicast MAC Addresses:
0 Multicast MAC Addresses:
0 Unicast Bundle MAC Addresses:
0 Multicast Bundle MAC Addresses:
The following example shows sample output from the show controllers TenGigE internal command for the Cisco CRS 14-Port 10-Gigabit Ethernet LAN/WAN-PHY Interface Module:
RP/0/RP0/CPU0:router# show controllers TenGigE 0/1/0/0 internal Thu Oct 7 18:27:01.022 EST
Total Power Available on PLIM for XFP's: 35000 mW Power used by Inserted XFP's: 33000 mW
Power Available: 2000 mW
Port Power Used State
00 2500 mW XFP Inserted and Powered On 01 2500 mW XFP Inserted and Powered On 02 1500 mW XFP Inserted and Powered On 03 2500 mW XFP Inserted and Powered On 04 2500 mW XFP Inserted and Powered On 05 1500 mW XFP Inserted and Powered On 06 2500 mW XFP Inserted and Powered On 07 2500 mW XFP Inserted and Powered On 08 2500 mW XFP Inserted and Powered On 09 2500 mW XFP Inserted and Powered On 10 2500 mW XFP Inserted and Powered On 11 2500 mW XFP Inserted and Powered On 12 2500 mW XFP Inserted and Powered On 13 2500 mW XFP Inserted and Powered On
The following example shows sample output from the show controllers TenGigE mac command for the Cisco CRS 14-Port 10-Gigabit Ethernet LAN/WAN-PHY Interface Module:
RP/0/RP0/CPU0:router# show controllers TenGigE 0/1/0/0 mac Thu Oct 7 18:27:34.289 EST
Operational address: 0014.f294.6776 Burnt-in address: 0014.f294.6776
PLA 0 port 0 MAC enabled Rx MAC disabled Administrative state: Forced Remote fault Operational state: Remote fault
0 HSRP/VRRP MAC addresses VLAN Ethertype: 0x8100 QinQ Ethertype: 0x88a8 MTP Ethertype: 0x88e7 4 VLAN UIDB entries
VLAN1 VLAN2 Packet Type Flags UIDB Result Flags
0 0 VLAN 1 VLAN
0 0 ARPA 1 ARPA
0 0 SAP 1 SAP
0 0 1 SNAP
Cisco IOS XR Interface and Hardware Component Command Reference for the Cisco CRS Router, Release 5.1.x
OL-30349-01 49
Ethernet Interface Commands on the Cisco IOS XR Software
show controllers (Ethernet)
The following example shows sample output from the show controllers TenGigE phy command for the Cisco CRS 14-Port 10-Gigabit Ethernet LAN/WAN-PHY Interface Module:
RP/0/RP0/CPU0:router# show controllers TenGigE 0/1/0/0 phy Thu Oct 7 18:27:51.884 EST
802.3ae Sections
================
PMA/PMD
Previous Alarm Status:
PMA/PMD NOT Locked to Local Signal PMA/PMD Local Fault
SR Ability Loopback Ability Rx Local Fault Current Alarm Status:
PMA/PMD NOT Locked to Local Signal PMA/PMD Local Fault
PCS Rx Link DOWN
PCS Local Fault Detected PCS Rx Local Fault Detected PCS Rx NOT Block Locked PCS Rx Link Status DOWN PCS Error'd Block Counts: 0 PCS BER Counts: 0
PCS has NO Block Lock Current Alarm Status:
PCS Rx Link DOWN
PCS Local Fault Detected PCS Rx Local Fault Detected PCS Rx NOT Block Locked PCS Rx Link Status DOWN PCS Error'd Block Counts: 0 PCS BER Counts: 0
PCS has NO Block Lock WIS: HW In LAN Mode - No Info
XFP General Info:
=================
UDI Checking: Disabled
PHY/XFP Status: XFP Not UDI Compliant XFP is Working as expected
XFP Info:
=========
Max Power Dissipation: 2500 mW XFP Type: 10GBASE-LR
Vendor Name: CISCO-SUMITOMO Vendor Part Number: SXP3101NV-C1 Vendor OUI: 0x00-0x00-0x5f Vendor Hardware Revision: C Vendor Serial number: ECL120701L2 Date Code (yy/mm/dd): 08/02/27 Lot Code: D0
Cisco PID: XFP-10GLR-OC192SR Cisco VID: V02
Cisco PN: 10-1989-02 ID: XFP
Ethernet Interface Commands on the Cisco IOS XR Software show controllers (Ethernet)
Extended ID: 0x58
TX ref clock input is not required CDP is supported
Power Level 2 (2.5W max. power) Minimum bit rate is 9900 MBits/s.
Maximum bit rate is 10300 MBits/s.
XFP Detail Info: AUX 1: +3.3V Supply Voltage: 0x70
AUX 2: Auxiliary monitoring not implemented: 0x0 XFP Status: enabled.
laser is enabled MOD NR is not ready is powered off
doesn't have interrupt(s) has LOS
data is ready TX path is ready
TX laser is not in fault condition TX path CDR is locked
RX path is not ready RX path CDR is not locked Alarms:
Low RX power alarm Warnings:
Low RX power warning THRESHOLDS
High Alarm Low Alarm High Warning Low Warng
Temperature C 80.0 -15.0 75.0 -10.0
Voltage V 000.0000 000.0000 000.0000 000.000
Bias Current mA 100.0000 000.0000 080.0000 000.000 Transmit power mW 015.8480 001.2580 010.0000 001.990 Receive power mW 022.3870 000.1810 014.1250 000.280