• set br0
• set br1 (not supported by IPv6)
Procedure 31-12 Set br0
1 Select RGW from the top-level menu in the GPON Web-Management System window.
2 Select the LAN option from the RGW menu.
The RGW -> LAN window appears; see Figure 31-32.
Figure 31-32 LAN window
3 Configure the parameters for the LAN service.
Table 31-28 describes the fields to select for the LAN IPv4 service.
Table 31-28 LAN IPv4 service parameters
Field Description
Configure the Broadband Router, ID Address, and Subnet mask for LAN interface
Select br0 from the drop-down menu
Setup -- IPv4:
IP Address Set static IP address if the DHCP Client is not be selected.
Subnet mask Set subnet mask if the DHCP Client is not be selected.
Enable DHCP Client Select, if wanted. If enabled, the IP address/subnet mask of br1 will be assigned automatically by DHCP server.
DHCP IP Address Show the DHCP IP address.
DHCP Subnet Mask Show the DHCP subnet mask.
Start IP Address Set the first address to be assigned by the DHCP server on the LAN interface. It is used when Enable DHCP Server field is selected.
End IP Address Set the last address to be assigned by the DHCP server on the LAN interface. It is used when Enable DHCP Server field is selected.
(1 of 2)
4 Click Apply/Save to save selections.
5 Configure more parameters for the LAN service.
Table 31-29 describes the fields in the RGW -> LAN window but not part of the Setup -- IPv4 section.
Table 31-29 LAN service parameters
6 Click Add or Remove to save selections.
See the Setup -- IPv6 section of the LAN window; see Figure 31-33.
Learned Time (hour) Set the lease time in hours of client assigned addresses. It is used when Enable DHCP Server field is selected.
Field Description
Static IP Lease List (A maximum 32 entries can be configured)
Add or remove items from this list
Reserved IP Address List (A maximum 10 entries can be configured)
Add or remove items from this list
DHCP Leases DHCP Leases table list can not be added
or removed manually
Field Description
(2 of 2)
Figure 31-33 Setup -- IPv6 section of LAN window
7 Scroll down in the RGW -> LAN window.
The Setup -- IPv6 section appears; see Figure 31-34.
Figure 31-34 Setup -- IPv6 section of LAN window
8 Configure the parameters for the LAN IPv6 service.
Table 31-30 describes the fields in the IPv6 LAN Applications window.
Table 31-30 IPv6 LAN application parameters
Field Description
Enable RADVD Enable to publish prefix and route
information
MaxRtrAdvInterval(s) Set the maximum interval of sending RA packets
MinRtrAdvInterval(s) Set the minimum interval of sending RA packets.
Router Life Time(s) Set the lifetime associated with the route in units of seconds
Enable ULA Prefix Advertisement Enable state of ULA (Unique Local Address) Prefix
Prefix Set the ULA prefix
Preferred Life Time (hour) Set the preferred lift time of the prefix (in hours) published in Router
Advertisement (1 of 2)
9 Click Apply/Save.
Review you changes in the IPv6 LAN Applications window; see Figure 31-35.
Valid Life Time (hour) Set the valid life time of the prefix (in hours) published in Router
Advertisement. Prefix Valid Lifetime must always be larger than or equal to Prefix Preferred Lifetime.
Enable DHCPv6 server Enable DHCPv6 server in LAN side Publish self as DNS server Set if wanted. Enable to publish clients
IPv6 address in LAN side as DNS server
Stateless Enable stateless mode
Stateful Enable stateful mode
Start interface ID Set value which indicates the beginning of the interface ID pool. Interface ID does not support ZERO COMPRESSION
"::". Please enter the complete information. For example: Please enter
"0:0:0:2" instead of "::2".
End interface ID Set value which indicates the end of the interface ID pool. Interface ID does not support ZERO COMPRESSION "::".
Please enter the complete information.
For example: Please enter "0:0:0:2"
instead of "::2".
Leased Time (hour) Set the preferred life time in hours of client assigned addresses. A setting of -1 indicates an infinite lease.
Field Description
(2 of 2)
Figure 31-35 IPv6 LAN statistics window
10 STOP. This procedure is complete.
Procedure 31-13 Set br1
1 Select RGW from the top-level menu in the GPON Web-Management System window.
2 Select the LAN option from the RGW menu.
The RGW -> LAN window appears; see Figure 31-36.
Figure 31-36 RGW -> LAN window
3 Configure the parameters for the LAN service.
Table 31-31 describes the fields to select for the LAN service.
Table 31-31 LAN IPv4 service parameters
Field Description
Configure the Broadband Router, ID Address, and Subnet mask for LAN interface
Select br1 from the drop-down menu
Setup -- IPv4:
IP Address Set static IP address if the DHCP Client is not be selected Subnet mask Set subnet mask if the DHCP Client is not be selected Enable DHCP Client Select, if wanted. If enabled, the IP address of br0 will be
assigned automatically by DHCP server.
DHCP IP Address Show the DHCP IP address
DHCP Subnet Mask Show the DHCP subnet mask
Enable DHCP Server Select to enable DHCP server on LAN side
Start IP Address Set the first address to be assigned by the DHCP server on the LAN interface. It is used when Enable DHCP Server field is selected.
(1 of 2)
4 Click Apply/Save to save selections.
5 Configure more parameters for the LAN service.
Table 31-32 describes the fields in the RGW -> LAN window but not part of the Setup -- IPv4 section.
Table 31-32 Additional LAN service parameters
6 Click Add or Remove to save selections.
The window with information configured in step 5 appears; see Figure 31-37.
End IP Address Set the last address to be assigned by the DHCP server on the LAN interface. It is used when Enable DHCP Server field is selected.
Learned Time (hour) Set the lease time in seconds of client assigned addresses.
It is used when Enable DHCP Server field is selected.
Field Description
Static IP Lease List (A maximum 32 entries can be configured)
Add or remove items from this list
Reserved IP Address List (A maximum 10 entries can be configured)
Add or remove items from this list
DHCP Leases DHCP Leases table list can not be added
or removed manually
Field Description
(2 of 2)
Figure 31-37 LAN service window
7 Review the br1 service statistics.
The br1 service statistic window appears; see Figure 31-38.
Figure 31-38 br1 service statistic window
8 STOP. This procedure is complete.