Setting Examples
GLOBAL SETTING / SYSTEM / GAS SENSOR TYPE Range NONE, TYPE1, TYPE2
6.2.1. Protocol Setup
6.2.1.2. IEC60870-5-101 Protocol Setup
ETR300-R can be programmed for communication using the IEC60870-5-101 through communication port1, port2 or port3.
Move to “MAIN MENU/ GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/
IEC870-5-101” to select setting for IEC60870-5-101.
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ Function Range DISABLE, ENABLE
Default DISABLE Step ~ Set an use of IEC60870-5-101.
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ COM Port Range PORT1, PORT2, PORT3
Default PORT1 Step ~
Select a port to use IEC60870-5-101 communication.
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ Address Range 1 ~ 65535
Default 1 Step 1
Enter the slave(ETR300-R) address for IEC60870-5-101 comm- unication.
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ ASDU Addr Range 0~65535
Default 0 Step 1
Select the Application Service Data Unit Address.
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ Cyclic Period Range 1~60000 sec
Default 60 Step 1 sec
Select the Cyclic Period.
It is to set interval time between Point set for Cyclic.
[IEC60870-5-101]
>ASDU Addr: 0
>Cyclic Period: 60 [1~60000:1]
[IEC60870-5-101]
>ASDU Addr: 0
>Cyclic Period: 60 [0~65535:1]
>Function: DISABLE
>COM Port: PORT1 [PORT1/PORT2/PORT3]
[IEC870-5-101]
>Function: DISABLE COM Port: PORT1 [DISABLE/ENABLE]
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ Event Period Range 0~255 sec
Default 15 Step 1sec
Select the delay time before events are sent. Single event or several events occur and then if new event is not generated during the delay time, the event(s) already generated is(are) sent to a Master.
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ Retries Range Applicable for lower than Ver 3.6 of ETR300-R : 0 ~ 2
Applicable for Ver 3.6 or higher of ETR300-R : 0 ~ 255
Default 0 Step 1
Set the Data retires number.
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ Conf. Timeout Range 1 ~ 255 sec
Default 10 Step 1 sec
Set the wait time till receive the Data Confirm (ACK) of master after transfer the Data. If there isn’t the Confirm during this setting time and Data retries is available, ETR300 transfers the Data again.
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ Max Poll Tim Range 1 ~ 255 sec
Default 10 Step 1 sec
Set the Data Polling period time.
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ ADSU Addr Size*
Range 1 ~ 2
Default 2 Step 1
Enter the size of cause of transmission.
[IEC60870-5-101]
>Conf.Timeout: 10 [1~255:1s]
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ Link Confirm*
Range NEVER, ALWAYS
Default ALWAYS Step ~ Enter the Link layer confirm mode.
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ Link Addr Size*
Range 1 ~ 2
Default 1 Step 1
Enter the size of link address.
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ Rx Frame Size*
Range 0 ~ 261
Default 261 Step 1
Enter the maximum size of received frame.
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ Rx Frame TO*
Range 0(OFF), 1 ~ 255 sec
Default 15 Step 1 sec
Enter the maximum amount of time to wait for a complete frame after receiving the frame sync.
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ Tx Frame Size*
Range 0 ~ 261
Default 261 Step 1
Enter the maximum size of transmitted frame.
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ COT Size*
Range 1 ~ 2
Default 1 Step 1
Enter the size of cause of transmission.
[IEC60870-5-101]
>COT Size : 1
>IOA Size : 2 [1~2:1]
[IEC60870-5-101]
>Tx Frame Size: 261
>COT Size : 1 [0~261:1]
[IEC60870-5-101]
>Rx Frame Size: 261
>Rx Frame TO : 15 [0(OFF),0~255:1s]
[IEC60870-5-101]
>Link Addr Size: 1
>Rx Frame Size: 261 [0~261:1]
[IEC60870-5-101]
>Link Addr Size: 1
>Rx Frame Size: 261 [1~2:1]
[IEC60870-5-101]
>ADSU Addr Size: 2
>Link Confirm:ALWAYS [NEVER/ALWAYS]
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ IOA Size*
Range 1 ~ 3
Default 2 Step 1
Enter the size of information object address.
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ One Ch Response*
Range NO, YES
Default NO Step ~
This allows to send one character response instead of a fixed length NACK when no response data available.
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ Fram Repet’ TO*
Range 0(OFF), 1~255sec
Default 30 Step 1 sec
Enter the time out for repetition of frames(or incremental application layer timeout).
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101 / Select Timeout*
Range 0(OFF), 1~255
Default 5 Step 1
Enter the period after a previously received select will timeout.
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ CMD Termination*
Range NO, YES
Default YES Step ~
Select whether to send Activation Termination upon completion of commands other than set point commands.
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ CSE Termination*
Range NO, YES
Default YES Step ~
Select whether to send Activation Termination upon completion of set point commands.
>One Ch Response: NO
>Frame Repet’ TO: 30 [0(OFF),0~255:1s]
[IEC60870-5-101]
>One Ch Response: NO
>Frame Repet’ TO: 30 [NO/YES]
[IEC60870-5-101]
>COT Size : 1
>IOA Size : 2 [1~3:1]
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ Clock Sync’ Evt*
Range NO, YES
Default YES Step ~
Select whether to generate spontaneous clock synchronization events
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ MSP Time-Tag**
Range CP56, CP24
Default CP56 Step ~
Select whether a time tag format for single-point.
y CP56 : The time tag format is CP56Time2a.
y CP24 : The time tag format is CP24Time2a.
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ MIT Time-Tag**
Range CP56, CP24
Default CP56 Step ~
Select whether a time tag format for integrated totals.
y CP56 : The time tag format is CP56Time2a.
y CP24 : The time tag format is CP24Time2a.
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ MME Time-Tag**
Range CP56, CP24
Default CP56 Step ~
Select whether a time tag format for measured value and normalized value for general event except for fault current event.
y CP56 : The time tag format is CP56Time2a.
y CP24 : The time tag format is CP24Time2a.
GLOBAL SETTING/ COMMUNICATION/ PROTOCOL SETUP/ IEC870-5-101/ MIT Time-Tag**
Range CP56, CP24
Default CP56 Step ~
Select whether a time tag format for integrated totals.
y CP56 : The time tag format is CP56Time2a.
y CP24 : The time tag format is CP24Time2a.
[IEC60870-5-101]
>MME Time-Tag: CP56
>Flt Time-Tag: CP56 [CP56,CP24]
[IEC60870-5-101]
>MME Time-Tag: CP56
>Flt Time-Tag: CP56 [CP56,CP24]
[IEC60870-5-101]
>MSP Time-Tag: CP56
>MIT Time-Tag: CP56 [CP56,CP24]
[IEC60870-5-101]
>MSP Time-Tag: CP56
>MIT Time-Tag: CP56 [CP56,CP24]
[IEC60870-5-101]
>CSE Termination:YES
>Clock Sync’ Evt:YES [NO/YES]
NOTE : 1. The above settings marked with * shall be Ver 3.6 or higher of ETR300-R to be indicated.
2. In case ETR300 is the standard type, the above settings marked with ** shall be Ver 3.9 or higher of ETR300-R to be indicated.
3. In case ETR300 is the External O/I option type, the above settings marked with **
shall be Ver 4.10 or higher of ETR300-R to be indicated.