13 Technical data
13.7 Interfaces
Technical data 13.5 Inputs
Inputs MF1 multifunctional input, adjustable
• Hi > 12 V
• Lo < 3 V
→ See Page 44, Table 13, parameter “ActStat”.
Circuit protection None; no reverse-polarity protection.
Table 29: Inputs
13.6 Outputs
Outputs MF1 and MF2 multifunctional outputs, type B (push/pull), adjustable
• Hi > UV –3 V
• Lo < 2 V
→ See Page 44, Table 13 and Page 50, Table 18, parameter
“ActStat”.
Maximum output current Max. 100 mA
Output load • Capacitive: 100 nF
• Inductive: 20 mH Table 30: Outputs
13.7 Interfaces
Data interface EtherCAT®
Data transmission rate 100 Mbps, full duplex Table 31: Interfaces
Technical data 13.8 Ambient conditions
Protection class III
For operation in PELV (protective extra low voltage) systems with safe separation.
Electromagnetic compatibility 1) EN 61000-6-2, EN 55011, Class A Ambient temperature range See type-specific data
→ See Page 109, Table 69.
Storage temperature range –40 °C … +75 °C
Enclosure rating IP65
Effect of air pressure 0.3 ppm/hPa
Effect of temperature 1 ppm/K
Temperature drift Typically 0.1 mm/K
Maximum traversing speed 30 m/s
Maximum change in acceleration 15 m/s² Vibration resistance (sine) EN60068-2-6
Noise EN60068-2-64
Shock resistance EN 60086-2-27
1) The device may cause interference if used in a residential environment.
Table 32: Ambient conditions
13.9 Structural design
Dimensions → See Page 72, Chapter 13.1.
Weight • Distance measuring device: 800 g
• Alignment bracket (optional): 800 g
Materials • Housing: Cast aluminum GD-AlSi12Cu1 (3.2982.05)
• Front screen: PMMA
Connections M12, SpeedCon™
Display • 6-digit with a 5 x 7 dot matrix
• Overflows are indicated by the maximum value that can be displayed, –99,999 or 999,999.
Table 33: Structural design
Accessories
14 Accessories
14.1 Reflectors and reflective tape
14.1.1 Reflectors
Fig. 26: Reflector 0.3 x 0.3 m², Diamond Grade, mounted
Description Reflector 0.3 x 0.3 m² Diamond Grade, mounted to ALMG3 base plate
Type PL240DG
Part no. 1017910
Fig. 27: Reflector 0.6 x 0.6 m² Diamond Grade, mounted
Description Reflector 0.6 x 0.6 m² Diamond Grade, mounted to ALMG3 base plate
Type PL560DG
Accessories
Fig. 28: Reflector 1.0 x 1.0 m² Diamond Grade, mounted
Description Reflector 1.0 x 1.0 m² Diamond Grade, mounted to ALMG3 base plate
Type PL880DG
Part no. 1018975
Silicon wire 2 m,
3 x 0.75 mm2, open ending
Fig. 29: Reflector 0.3 x 0.3 m² Diamond Grade, mounted, including heating Description Reflector 0.3 x 0.3 m² Diamond Grade, mounted to ALMG3 base plate,
including controlled heating +20 °C, 230 V AC, 200 W, IP64
Type PL240DG-H
Part no. 1022926
Accessories
Silicon wire 2 m,
3 x 0.75 mm2, open ending Fig. 30: Reflector 0.6 x 0.6 m² Diamond Grade, mounted, including heating Description Reflector 0.6 x 0.6 m² Diamond Grade, mounted to ALMG3 base plate,
including controlled heating +20 °C, 230 V AC, 200 W, IP64
Type PL560DG-H
Part no. 1023888
14.1.2
Reflective tape
Fig. 31: Diamond Grade reflective tape
Description Diamond Grade reflective tape, customizable size
Type REF-DG
Part no. 4019634
Description Diamond Grade reflective tape, 749 x 914 mm² sheet
Type REF-DG
Part no. 5320565
Accessories
14.2 Plug connectors and cables
14.2.1 Connection cables with M12 male connector, straight, to M12 male connector, straight
Description Type Part no.
Connection cable, Ethernet patch cable, 2 m, M12 male connector,
straight and 4-pin, D-coded, to M12 male connector, straight SSL-1204-G02MZ90 6048241 Connection cable, Ethernet patch cable, 5 m, M12 male connector,
straight and 4-pin, D-coded, to M12 male connector, straight SSL-1204-G05MZ90 6048242 Connection cable, Ethernet patch cable, 10 m, M12 male connector,
straight and 4-pin, D-coded, to M12 male connector, straight SSL-1204-G10MZ90 6048243
14.2.2 Connection cables with M12 male connector, angled, to M12 male connector, straight
Description Type Part no.
Connection cable, Ethernet patch cable, 2 m, M12 male connector,
angled and 4-pin, D-coded, to M12 male connector, straight SSL-1204-F02MZ90 6048250 Connection cable, Ethernet patch cable, 5 m, M12 male connector,
angled and 4-pin, D-coded, to M12 male connector, straight SSL-1204-F05MZ90 6048251 Connection cable, Ethernet patch cable, 10 m, M12 male connector,
angled and 4-pin, D-coded, to M12 male connector, straight SSL-1204-F10MZ90 6048252
14.2.3 Connection cables with M12 male connector, straight, to RJ45 connector, straight
Description Type Part no.
Connection cable, Ethernet patch cable, 2 m, M12 male connector,
straight and 4-pin, D-coded, to RJ45 male connector, straight SSL-2J04-G02MZ90 6048244 Connection cable, Ethernet patch cable, 5 m, M12 male connector,
straight and 4-pin, D-coded, to RJ45 male connector, straight SSL-2J04-G05MZ90 6048245 Connection cable, Ethernet patch cable, 10 m, M12 male connector,
straight and 4-pin, D-coded, to RJ45 male connector, straight SSL-2J04-G10MZ90 6048246
14.2.4 Connection cables with M12 male connector, angled, to RJ45 connector
Description Type Part no.
Connection cable, Ethernet patch cable, 2 m, M12 male connector,
angled and 4-pin, D-coded, to RJ45 connector SSL-2J04-F02MZ90 6048253
Connection cable, Ethernet patch cable, 5 m, M12 male connector,
angled and 4-pin, D-coded, to RJ45 connector SSL-2J04-F05MZ90 6048254
Connection cable, Ethernet patch cable, 10 m, M12 male connector,
angled and 4-pin, D-coded, to RJ45 connector SSL-2J04-F10MZ90 6048255
Accessories
14.2.5 M12 male connector, straight with cable, open end
Description Type Part no.
M12 male connector, straight, 4-pin, D-coded, 2 m cable, open end STL-1204-G02MZ90 6048247 M12 male connector, straight, 4-pin, D-coded, 5 m cable, open end STL-1205-G05MZ90 6048248 M12 male connector, straight, 4-pin, D-coded, 10 m cable, open end STL-1210-G10MZ90 6048249
14.2.6 M12 male connector, angled with cable, open end
Description Type Part no.
M12 male connector, angled, 4-pin, D-coded, 2 m cable, open end STL-1204-W02MZ90 6048256 M12 male connector, angled, 4-pin, D-coded, 5 m cable, open end STL-1204-W05MZ90 6048257 M12 male connector, angled, 4-pin, D-coded, 10 m cable, open end STL-1204-W10MZ90 6048258 M12 male connector, angled, 4-pin, D-coded, 25 m cable, open end STL-1204-W25MZ90 6048259
Accessories
14.3 Mounting systems
130.8 (5.15)
75.7 (2.98)
85.3 (3.36)
max. 120.8 (4.76)
126 (4.96)
126 (4.96)
Ø 5.4 (0.21)
5 (0.20)5 (0.20)5 (0.20)5 (0.20) 48 (1.89)48 (1.89)12.7 (0.50)
137 (5.39)
14.5 (0.57)
All dimensions in mm (inch) Fig. 32: Alignment bracket
Description Alignment bracket
Type BEF-AH-DX100
Part no. 2058653
Material Galvanized sheet steel
Accessories
14.4 Other accessories
235 (9.25)
135 (5.31) 305 (12.01)
345 (13.58)
154 (6.06)
51.5°
51.5
°
R74
M10
10.5 (0.41)26 (1.02) All dimensions in mm (inch)
Fig. 33: Cooler housing
Description Cooler housing
Type TPCC-Dx100
Part no. 6048328
Material Glass fiber reinforced plastic (GFRP)
Ambient operating temperature –20 °C … +75 °C (temporarily +80 °C)
Supply voltage 24 V DC ± 20%
Current consumption 15 A at 24 V DC
Menu structure
15 Menu structure
SwVers HwVers
ActSta Functn
Dist Speed Srvice LsrOff Preset
Count Choose option Choose option
Display only when MFxOn: Enable
MFxOn Offset SpecFu
Level Bargraph Level num. Temperature Warning Error
2 s
Enter value
see see see
see Display only when more?: Yes
1 2 3
Choose option Display only *
see
* Display as ticker
* Display as ticker Measurement
value
Menu structure
WrnLsr WrnLvl WrnTemp WrnPlb NotRdy
Heat
AvgDst AvgSpd MsrDir
Heat
Reset SpecFu
FreqSet
Choose option Choose option Choose option Enter value Choose option Sure?Sure?
OK
only versions
DL100-2xHx2212 only versions DL100-2xxB2212
Srvice
Choose option Choose option Choose option Choose option Choose option Choose option
Limit Hyst
Dist
Choose option
Limit Sign
Speed
Enter value
sPrset Preset
Enter value
Choose option Enter value
4 4 4
4 3
ErrRej
Choose option
Index
A
Accessories... 76
Alignment bracket ... 81
Cooler housing ... 82
Miscellaneous ... 82
Plug connectors and cables ... 79
Reflectors ... 76
Alignment ... 29
Distance measuring device and reflector ... 29
Using the alignment bracket ... 32
Alignment bracket Mounting ... 30
Alignment bracket (accessories) ... 81
Ambient conditions ... 75
Attenuation Nominal level ... 29
Warning limit ... 29
C Changes ... 13
CiA 406 device profile ... 64
Cleaning ... 68
Customer service ... 10
D Device selection ... 76
Dimensions Alignment bracket ... 81
Distance measuring device ... 72
Display ... 20
Disposal ... 70
E Electrical connection... 33
Electrical specialists ... 13
Environmental protection ... 11
Error messages ... 70
EtherCAT® ... 54
EU declaration of conformity ... 10
F Factory setting ... 53
H Hazard warnings ... 15
I Identification ... 16
Improper use ... 12
Inputs ... 74
Intended use ... 12
Interfaces ... 74
L Laser ... 73
Laser radiation ...14, 15 Laser radiation warning sign ... 14
LEDs ... 19
MF1/2 ... 19
Limitation of liability ... 10
M Maintenance ... 68
Menu structure ... 83
Minimum distance ... 26
Mounting ... 24
Alignment ... 29
Alignment bracket ... 30
Alignment bracket and distance measuring device ... 30
Distance measuring device ... 30
Distance measuring device and adjacent data transmission photoelectric sensor ... 28
Minimum distance...26, 27 Multiple distance measuring devices ... 26
Notes ... 24
Procedure ... 24
Reflector ... 25
Mounting systems ... 81
O Object 6000h – Operating Parameters ... 65
6003h – Preset Value ... 65
6004h – Position Value ... 66
6005h – Linear Encoder Measuring Step Settings ... 66
6030h – Speed Value ... 67
6500h – Operating Status ... 67 6501h – Single-turn Resolution and
Index
Index
6509h – Offset Value ... 67
Operating elements... 18
Operating instructions ...8
Operating modes ... 20
Operating personnel Requirements ... 13
Operation ... 39
Changing a value ... 40
On the measuring device ... 39
Selecting an option ... 40
Selecting parameters ... 39
Operational safety ...13, 15 Outputs ... 74
P Parameter description ... 41
Dist (MF1) ... 45
Performance data ... 73
Plug connectors and cables (accessories) ... 79
Preset Description ... 48
Pushbuttons ... 20
Q Qualified personnel ... 13
Requirements ... 13
R Reflective tape ... 78
Reflector
Electrical connection ... 33
Scope of delivery ... 10
Status indicators ... 18
Storage ... 23
Structural design ... 75
Structure ... 17
Supply ... 73
T Technical data ... 71
Trained personnel ... 13
Transport ... 22
Transport inspection ... 22
Troubleshooting ... 69
Type code ... 76
Type label ... 16
U UL safety notes ...7
W Warning messages ... 69
Wiring instructions ... 33
8023160/en/2018-06-12
Further locations at www.sick.com Australia
Phone +61 3 9457 0600 1800 334 802 – toll free E-mail [email protected]
Phone +55 11 3215-4900 E-mail [email protected]
Phone +56 2 2274 7430 E-mail [email protected] China
Phone +86 20 2882 3600 E-mail [email protected]
Phone +49 211 5301-301 E-mail [email protected] Hong Kong
Phone +852 2153 6300 E-mail [email protected] Hungary
Phone +36 1 371 2680 E-mail [email protected] India
Phone +91 22 6119 8900 E-mail [email protected]
Israel
Phone +972 4 6881000 E-mail [email protected] Italy
Phone +39 02 274341 E-mail [email protected] Japan
Phone +81 3 5309 2112 E-mail [email protected] Malaysia
Phone +6 03 8080 7425 E-mail [email protected] Mexico
Phone +52 (472) 748 9451 E-mail [email protected] Netherlands
Phone +31 30 2044 000 E-mail [email protected] New Zealand Phone +64 9 415 0459
0800 222 278 – toll free E-mail [email protected]
Phone +65 6744 3732 E-mail [email protected] Slovakia
Phone +421 482 901201 E-mail [email protected] Slovenia
Phone +386 591 788 49 E-mail [email protected] South Africa
Phone +27 11 472 3733 E-mail [email protected]
South Korea
Phone +82 2 786 6321 E-mail [email protected]
Phone +886 2 2375-6288 E-mail [email protected] Thailand
Phone +66 2645 0009 E-mail [email protected] Phone +44 1727 831121 E-mail [email protected]