DPT Integration is recommended when using the VPS with the KX-TD500, however, Inband Integration is necessary when:
• the PBX has available SLT ports but no available DPT ports.
• the cards installed in the PBX or the software version of the PBX do not support DPT Integration.
Programming procedures and availability may vary by PBX model, software version, etc. Refer to the documentation included with the PBX or consult your dealer for more information.
1. Assignment of the extension card to be connected to the VPS Note
• If the VPS card to which the VPS will be assigned is already installed in the KX-TD500, proceed to step 2. If installing a new VPS card, begin with step 1.
a. Go to the 1-1 Slot Assignment screen.
b. Assign the slot card type to be installed to DHLC, HLC, SLC, ESLC, or SLC-M SLT interface supports.
c. Click Apply to save the slot card type assignment.
d. Set Status to INS.
2. Assignment of the extension ports to be connected to the VPS a. Go to the 1-3 Extension Port Assignment screen.
b. Assign Attribute of the port to be connected to TEL (default).
5.6 KX-TD500 PBX Programming for Inband Integration
Note
• Specify the extension group number (126 or 127 by default) to which VM or AA extension groups have been assigned. Group numbers 1 to 128 are available to the VPS through additional programming.
e. Click Apply to save the changed data.
f. Set Status to INS.
3. Assignment of the extension line to be connected to the VPS a. Go to the 4-2 Extension Line 1/2 screen.
b. Set Data Line Mode to Yes.
c. Click Apply to save the changed data.
Document Version 3.0 2010/06 Installation Manual 151
5.6 KX-TD500 PBX Programming for Inband Integration
Note
• This program prevents the VM port from being interrupted by the call waiting, hold recall, and executive busy override features during a call.
4. Settings for the trunk (CO line) features
Program the appropriate trunk (CO line) feature settings depending on how your customer plans to use the VPS.
• The VPS answers all incoming trunk (CO line) calls promptly.
See Example Settings (1) later in this section.
• The VPS answers when the operator does not take the call after a specified number of rings.
See Example Settings (2) later in this section.
• The VPS answers when an extension user does not take the call after a specified number of rings.
See Example Settings (3) later in this section.
5.6 KX-TD500 PBX Programming for Inband Integration
Example Settings (1)
Program the PBX so that all trunk (CO line) calls are directed to the VPS (DIL feature).
1. Go to the 4-1 Trunk Line screen.
2. Assign the Destination for each time mode and trunk (CO line) to a specific extension number (VPS port).
3. Click Apply to save the changed data.
Note
• Specify the FDN for the extension group to which VM or AA has been assigned.
• In order to utilize the Caller ID features, you must set Caller ID to Enable.
Document Version 3.0 2010/06 Installation Manual 153
5.6 KX-TD500 PBX Programming for Inband Integration
Example Settings (2)
Program the PBX to direct incoming trunk (CO line) calls to an operator, and to then direct those calls to the VPS when the operator does not answer.
1. Program the PBX so that incoming trunk (CO line) calls are directed to an operator (DIL feature).
a. Go to the 4-1 Trunk Line screen.
b. Assign the Destination for each time mode and trunk (CO line) to a specific extension number.
c. Click Apply to save the changed data.
Note
• Specify the FDN for the extension group to which Operator has been assigned.
2. Program the PBX so that unanswered calls to the operator are redirected to the VPS (Intercept Routing No Answer feature).
a. Go to the 3-1 Trunk Group screen.
b. Assign the Intercept Destination for the trunk (CO line) group for each time mode.
c. Click Apply to save the changed data.
5.6 KX-TD500 PBX Programming for Inband Integration
Note
• Specify the FDN for the extension group to which VM or AA has been assigned.
3. Set the number of rings before a call is considered to be unanswered and therefore forwarded to the VPS (Intercept Routing No Answer timer).
a. Go to the 2-4 System Timer 1/2 screen.
b. Assign the Intercept Time parameter.
Document Version 3.0 2010/06 Installation Manual 155
5.6 KX-TD500 PBX Programming for Inband Integration
c. Click Apply to save the changed data.
5.6 KX-TD500 PBX Programming for Inband Integration
Example Settings (3)
Program the PBX to direct incoming trunk (CO line) calls to an extension or group and to then direct those calls to the VPS when they are not answered.
1. Program the PBX so that incoming trunk (CO line) calls are directed to an extension or group (DIL feature).
a. Go to the 4-1 Trunk Line screen.
b. Assign the Destination for each time mode and trunk (CO line) to a specific extension number.
c. Click Apply to save the changed data.
2. Program the PBX so that unanswered calls are redirected to the VPS (Intercept Routing No Answer feature).
a. Go to the 3-1 Trunk Group screen.
b. Assign the Intercept Destination for the trunk (CO line) group for each time mode.
c. Click Apply to save the changed data.
Document Version 3.0 2010/06 Installation Manual 157
5.6 KX-TD500 PBX Programming for Inband Integration
Note
• Specify the FDN for the extension group to which VM or AA has been assigned.
3. Program the amount of time that passes before unanswered calls are redirected to the VPS (Intercept Routing No Answer timer).
a. Go to the 2-4 System Timer 1/2 screen.
b. Assign the Intercept Time parameter.
5.6 KX-TD500 PBX Programming for Inband Integration
c. Click Apply to save the changed data.
Document Version 3.0 2010/06 Installation Manual 159
5.6 KX-TD500 PBX Programming for Inband Integration