COMMON CHARACTERISTICSCOMMON CHARACTERISTICS
13.5 MODULATING BUZZER MODULATING BUZZER
13.5 MODULATING BUZZER
R
REELLAAY Y DDEESSCCRRIIPPTTIIOONN CCOONNTTAACCTTS S FFEEAATTUURREESS NNAAMMEE//CCLLAAMMPPSS
Buzzer vie2 Jst Buzz
14.1 "NABOO" BOARD - USER
14.1 "NABOO" BOARD - USER SERVICE FUNCTIONS MANAGEMENTSERVICE FUNCTIONS MANAGEMENT Press the "settings" icon to access to the service
fun-ctions that are useful for the user such as:User set-User set-tings
tings, User language, which each allow access to the submenus shown below.
14.0 KEYBOARD 14.0 KEYBOARD
BLOCK SETTINGS BLOCK SETTINGS - activate profile block
- activate Profile block + manual cooking - activate required wash
SOUNDS SOUNDS - enable sounds - volume
HOME ICON SIZE HOME ICON SIZE - select home icon size
BRIGHTNESS and ENERGY SAVING BRIGHTNESS and ENERGY SAVING - brightness setting
- energy saving after
LANGUAGE LANGUAGE
- interface language (it, en, de, fr, es) DOWNLOAD HACCP LOG DOWNLOAD HACCP LOG - start date
- end date
SOFTWARE UPDATE SOFTWARE UPDATE - interface software - basic software - complete software CONFIGURE WI-FI CONFIGURE WI-FI - enable wi-fi
SERVICE SERVICE -ONLY
ONLY FOR USE BY THE TEFOR USE BY THE TECHNICIANCHNICIAN (enter password)
BOILER WASHING BOILER WASHING MODEL
-SERIAL NUMBER VERSION
-SOFTWARE
14.2 "NABOO" BOARD - FUNCTION INHIBITION 14.2 "NABOO" BOARD - FUNCTION INHIBITION The "block settings" function prevents users from changing the parameters of saved recipes.
•Press the "Block" icon on the display.
•This accesses the "block settings" screen where you can activate the "Profile Block" that prevents chan-ges to customized recipes or "Profile block + Manual Cooking" that not only blocks customized recipes but also makes it impossible to enter other recipes.
•Press "ACTIVATE" on the desired item and a pop-up window will appear asking for a password to confirm the block (password chosen by the user)
•The recipes are now blocked
•To unblock the recipes, return to "Block settings"
and press "Remove". Confirm by re-entering the previously used password.
NOTE:
NOTE: With "Required Wash" set to "ON", the oven calculates the need to perform the oven wash and blocks the oven when it has not been performed.
1401 1401
1402 1402
1403 1403 1400 1400
14.3
14.3 "NABOO" BOARD - DOWNLOAD LOG HACCP"NABOO" BOARD - DOWNLOAD LOG HACCP
•Press on the “HACCP” icon.
•The start and end date can be selected via the touch screen.
NOTE:
NOTE:Data over one year old cannot be exported
•Press "SAVE" icon
•A mask will appear requesting the insertion of the USB pen.
Remove the protective cap from the USB port to access it.
Insert the pen into the oven USB port (see figure).
•Press "SAVE" icon again
•On completion of export, a window appears that indicates that export has taken place successfully.
•Press the “BACK” button to go back to the oven main menu.
ATTENTION ATTENTION
After having removed the USB pen reposition the protection cover.
1406 1406
1407 1407
1408 1408 1
1440044 11440055
14.4 "NABOO" BOARD - SELECTION OF THE USER LANGUAGE 14.4 "NABOO" BOARD - SELECTION OF THE USER LANGUAGE
•Press "User language" or turn Scroller until “User language” is highlighted and confirm by pressing Scroller. (n. __ available languages)
•Select the desired language directly on the tou-chscreen or turn the Scroller to highlight it and con-firm by pressing the Scroller.
14.5 "NABOO" BOARD - SERVICE 14.5 "NABOO" BOARD - SERVICE
(FOR EXCLUSIVE USE OF THE AUTHORISED TECHNICIAN) Below find details of the functions useful for the
tech-nical service available in the NABOO version.
To enter the technical service programs, in the main screen, press the "settings" icon; the screen that appears shows the various service sectors available;
select SERVICE, enter password "lnx13" (or select SERVICE, enter password "lnx13" (or
"lnxtech" for software versions 3.01) and select
"lnxtech" for software versions 3.01) and select ENTER.
ENTER.
PASSWORD: "lnx13"
PASSWORD: "lnx13"
or
or
"lnxtech" "lnxtech"
(for software (for software versions 3.01)versions 3.01)
These functions are only for exclusive use of the These functions are only for exclusive use of the authorised technician
authorised technician
ATTENTION ATTENTION
On replacement of the electronic pc board it must be identified according to the oven model in which it is installed. It is therefore necessary to read CHAP. 20.3 "Substituting and mounting new
circuit boards."
1
1440099 11441100
14.6 "NABOO" BOARD - SERVICE - OVEN 14.6 "NABOO" BOARD - SERVICE - OVEN MODELMODEL Select the function "OVEN MODEL" using the touch
screen.
A screen appears (fig. 1412) that shows the following fields:
•Serial N.
•Oven model (electric, gas)
•Type of supply gas (if "gas oven" is selected)
•N. of trays
•Water hardness measured at the oven input
•Unit of measure of the temperature - °C o °F
•Boiler (if present)
•Type of washing (Washes present, solid clean was, solid cal wash... See chap. 22)
NOTE:
NOTE: the hardness of the water at the appliance input is set to a default of 20 in French degrees.
NOTE:
NOTE: the serial number indicated with LA 0200….
On the plate at the bottom of the control panel must be introduced: the entry password is “matrix1”. Observe the photographic sequence for verification/insertion of the fields described.
Press on SERIAL N° if it must be inserted (fig. 1410), the screen will appear (fig. 1414), introduce the serial number password“matrix1”“matrix1”(fig. 1415),
serial number password:
serial number password:
"matrix1"
"matrix1"
press Enter, insert the oven serial number, e.g. LA 0200... (fig. 1416) press Enter, is now possible to intro-duce the oven model data and features as. fig. 1417-1424. Press OK as indicated in fig. 1425 so as to send the features data of the oven model to the electronic pc board. The screen will appear that allows to conti-nue programming.
NOTE:
NOTE: With "Boiler" active, you can choose whether or not to activate "Solid Cal Wash".
ATTENTION ATTENTION
Each time the fields described above, relating to the oven model, are inserted or modified, the "SET
INVERTER MANAGEMENT" message will appear
1411 1411
1412 1412
14.6 "NABOO" BOARD - SERVICE - OVEN 14.6 "NABOO" BOARD - SERVICE - OVEN MODELMODEL
1414 1414 1413
1413
1417 1417 1416
1416
1420 1420 1419
1419
1423 1423 1422
1422
1426 1426 1425
1425
1415 1415
1418 1418
1421 1421
1424 1424
1427 1427
14.7 "NABOO" BOARD - SERVICE - TECHNICAL PARAMETERS 14.7 "NABOO" BOARD - SERVICE - TECHNICAL PARAMETERS In the “technical parameters” section, compare the list
of all pre-set programmable board parameters linked to the oven model set, chap. 14.1 in order to check and modify according to operator needs. (see atta-ched integrated list). Remember that following setting of the compulsory fields stated in chap. 14.1, the pro-grammable parameters are set automatically for the specific model according to the manufacturer’s stan-dards.
For each control of parameter values, refer to the table in attachment 2 where operative parameters are poin-ted out.
To change the setting attributed to the parameter, select via the touch screen, edit with the scroller and confirm by pressing the set key.
Exit from the section and saving of the new settings takes place using the “return” button.
NOTE:
NOTE: The parameter n°48 “enabling demo function”, after changing the value from “0” to “1”, allows to ena-ble the exclusive functioning of the keypad excluding demonstration regulators without the need for connec-tions to gas, water or three phase power supply for electrical ovens.
It will be sufficient, therefore, to power the oven with AC230V single phase voltage, access the "technical parameters" section and modify the value of parame-ter "48":
1- enabling of demo
0- enabling of normal functioning
The enabling of the demo function is indicated at the bottom of the touch screen in order to inform the ope-rator that the function is active. (Fig. 1430)
The USB EXPORT function enable exporting (from oven board to USB pen), the attributed technical para-meters; this function is useful in case of attribution of specific parameters for use in an oven network/chain.
ATTENTION ATTENTION
For safety reasons, certain parameters are locked ( ) even for the technician, and can only be amended by the manufacturing company, please ask the specific password to enable above men-tioned parameters altering only if necessary.
1428 1428
1430 1430
1429 1429
14.9 "NABOO" BOARD - SERVICE - BURNER MANAGEMENT
14.9 "NABOO" BOARD - SERVICE - BURNER MANAGEMENT(ONLY FOR GAS OVENS)
The “Burners management” section allows to check the: speed, ignition stages, minimum power, maxi-mum power of the cooking chamber burners and boi-ler (if it exists) settings, eventual speed change and burner activation test in order to check the correctness of adjustments (fig. da 1433 a 1436).
Full details in chap.17.
14.8
14.8 "NABOO" BOARD - "NABOO" BOARD - SERVICE - SERVICE - OPERATIONAL OPERATIONAL TESTSTESTS The "operational tests" section lets you display and
manually activate each individual relay on the board that activate the various parts of the appliance. To verify their operation, just select the desired icon.
Example: we can verify the operation of the cooking chamber lights by choosing the related button on the touch screen.
When the lights come on, the relay is operating cor-rectly. Otherwise, the operation can be verified by connecting a tester to the output on the transformer that powers the lights or on the output of the PC board. In this case, in order to open the control panel, refer to the description in chapter ---- and connect a magnet to the control panel to simulate the door clo-sing.
ATTENTION ATTENTION
For safety purposes, some relays are timed so they are disabled a few seconds after the Start.
The door must remain closed. Relay activation is indicated by the yellow box.
1
1443311 11443322
1433 1433
1435 1435
1434 1434
1436 1436
14.11
14.11 "NABOO" BOARD - DIAGNOSTICS"NABOO" BOARD - DIAGNOSTICS The purpose of this function is to monitor the oven performance, by checking:
•Increases in the temperature probes, their calibration and accuracy
•Relay activation status
•Automatic functions
All of these checks help the technician verify the proper operation of the regulators.
Select the diagnostics option. The screen will appear that displays the relay status and the temperature of the probes.
14.12 "NABOO" BOARD - SERVICE - DRAWER WASHING 14.12 "NABOO" BOARD - SERVICE - DRAWER WASHING Selecting "Drawer washing" access the related screen
that is split into "CombiClean2 Washes" and "CalFree Washes"
Generate CombiClean/CalFree Wash Drawer
RESET SET MAX
14.10 "NABOO" BOARD - SERVICE - INVERTER MANAGEMENT 14.10 "NABOO" BOARD - SERVICE - INVERTER MANAGEMENT See chap. 12 inverter.
1439 1439 1437 1437
1441 1441
1440 1440 1438 1438
14.13
14.13 "NABOO" BOARD - SERVICE - METERS"NABOO" BOARD - SERVICE - METERS The "meters" section lets you verify the operating hours of the different parts of the oven (in minutes "m"
or hours "h").
Using the "Reset" button, you can set the operating time of the individual parts back to zero.
The recorded times allows us to determine the servi-ces to be performed on the appliance. That is to say, once a certain amount of operating time has been reached for a part, the display will show what opera-tions must be performed. The "BACK" button exits the section.
ATTENZIONE ATTENZIONE
The section described above is useful in combi-nation with the "periodic maintenance table"
14.14
14.14 "NABOO" BOARD - SERVICE - OTHER SETTINGS"NABOO" BOARD - SERVICE - OTHER SETTINGS
"OTHER SETTINGS" lets you :
•activate demo mode which can be used to performchecks
•enable or disable sounds.
1444 1444
1445 1445 1
1444422 11444433
14.15 SOFTWARE UPDATE FOR "NABOO" BOARDS 14.15 SOFTWARE UPDATE FOR "NABOO" BOARDS
After having replaced the display board you have to update the software using the usb pendrive you found on the package together with the board.
ATTENTION ATTENTION
After having replaced the display board please be sure to have reconnect all the cables on the
display board
Give power supply to the oven, you will see some leds flashing on the power board. The display board has not leds turning on. After a while, approx. 1 minute, the display turn on showing the home page window.
Connect the usb pendrive on the usb connector you can find in the display board as indicated by in the photo 1447.
The led on the pendrive turns on when the stick is connected.
Press the “settings” key indicated by the arrow on the display (fig. 1448).
In the window appearing after having pressed the
“settings” key, press the key indicated in the photo 1449 for updating the software.
In the window that is appearing now there are three possible choises. Select the third one where it is writ-ten “software Completo interfaccia + base” (fig. 1450)
Select the updating file (fig.1451)
Wait for loading the file (fig. 1451a)
Confirm updating (press “YES” - fig. 1452)
Confirm updating (press “INSTALL” - fig.1452a)
After you have confirmed, you will see the screen in fig.1453, you do not need to do anything, wait until the oven restarts.
1446 1446
1448 1448
1450 1450
1452 1452
1452a 1452a
1447 1447
1449 1449
1451 1451
1451a 1451a
1453 1453
14.16 "NABOO" BOARD
14.16 "NABOO" BOARD - SETTING THE - SETTING THE DADATE AND TIMETE AND TIME
•Press the clock icon
•The screen appears where you can enter the date, time and time zone.
•Press above the date on the touch screen and a window will appear to enter the correct date. Once set, press "end"
•Do the same for the time
•Then select "time zone" and choose the proper time zone by scrolling through the options on the touch screen.
•Once all of the data have been entered, click on
"SAVE".
1454 1454
1455 1455
1456 1456
1457 1457