3.8.1. General Training Requirements: Effective training programs in peacetime are critical to meeting Expeditionary Air Force (EAF) and surge combat requirements. Munitions managers and supervisors at all levels establish and implement training and qualification programs to enable technicians to proficiently perform assigned contingency and routine munitions systems tasks. Training focuses on management of assigned programs and qualification of supervisors and technicians to execute effective control, accountability, storage, receipt, shipment, inspection, maintenance, assembly, flightline expediting, flightline delivery, and limited local disposition of conventional, precision guided, nuclear munitions and associated components.
3.8.1.1. Munitions training programs and training outlines will emphasize Combat Ammunition System operations, processing procedure, operation of Automatic Identification Technology (AIT) equipment, and TMRS as applicable throughout the range of munitions operations. When developing local training programs, maximize use of the Munitions Accountability Procedures Guide located on the AF/A4LW AFKN CoP.
3.8.1.2. Munitions qualification training will focus on checkout, operation and organizational level maintenance of assigned munitions tools, test, and handling equipment.
3.8.2. Combat Munitions Training (CMT) Program.
3.8.2.1. Munitions Supervision is responsible for establishing and implementing an effective CMT program and directs the Training Section/Element NCOIC in all stages of program development. The CMT program is designed to provide hands-on familiarization training to develop core knowledge for all 2W0XX and company grade officers assigned to the MUNS/Munitions Flight and will include all facets of the unit‘s conventional munitions contingency or OPLAN tasking (in-place or deployed). CMT is not intended to fully qualify personnel in all tasks. CMT programs should attempt to develop cross-functionality in the use of personnel to the maximum extent possible. For senior leaders in the unit (SMSgt, CMSgt, and Capt), CMT participation should focus on leadership, mentorship, hands-on review and adaptation of the CMT curriculum at the point of instruction.
3.8.2.2. The MUNS Superintendent/Flight Chief establish the number of personnel (total number or percentage of assigned) required to train on each contingency task to meet the unit's most demanding contingency requirements. In determining this, consider the highest probable usage of tasked munitions, criticality of supporting tasks, complexity of tasks performed, and the need for flexibility in the use of personnel.
3.8.2.2.1. Develop a task-training list used to manage training for all contingency operations. The task-training list will identify the task to be instructed and the required interval (not to exceed a maximum of 18 months). Consider task
complexity, frequency, duration, and ease of scheduling when determining the frequency of training.
3.8.2.2.2. The unit's conventional munitions contingency or OPLAN tasking (in-place or deployed) has primary emphasis in the CMT program (e.g., munitions production, outload, depot support), however, supporting tasks are equally critical.
Therefore the MUNS Superintendent/Flight Chief may designate personnel that only require CMT training on supporting tasks as identified on the task-training list. Use the UCML, weapons task qualification listing, integrated tasking order (ITO), collateral mission, aircrew training syllabus, OPLANs, Munitions Employment Plan (MEP), and base support plans to determine the scope of the training program.
3.8.2.2.3. ARC unit CMT programs are separate and distinct training programs, however ARC units should collaborate with their gaining commands/units to maximize the effectiveness of their CMT program. Total Force Integration (TFI) units should develop and maintain a single consolidated CMT program on each installation.
3.8.2.3. All 2W0XX personnel assigned outside the Munitions Squadron/Flight will attend CMT at intervals designated by the MUNS Superintendent/Flight Chief to maintain familiarization on core munitions tasks and meet combat training requirements of the 2W0X1 Munitions Systems Career Field Education and Training Plan (CFETP) and training outlined by the Munitions Superintendent/Flight Chief in the Master Task Listing (MTL). This may only be waived by the individual‘s Squadron Commander (or equivalent) for documented medical reasons.
3.8.2.4. Exemptions from CMT requirements:
3.8.2.4.1. Short-tour assignment locations when each member of the munitions organization receives a documented initial OPLAN briefing. Maintain OPLAN briefing documentation until personnel PCS.
3.8.2.4.2. Research, Test, and Development (RT&D) units when the base of assignment lacks sufficient resources to mount an effective program. Note: RT&D units co-located on installations with other operational or training units (e.g., ACC Fighter/Bomber, AETC Fighter/Bomber training) are required to complete CMT training with the co-located unit. The flight chief is responsible to coordinate and schedule CMT with the other unit.
3.8.2.5. The MUNS Superintendent/Flight Chief may use their discretion to certify completion of CMT training requirements for individuals when they can positively establish through training records or other deployed documentation that training received while deployed to an established contingency location satisfies CMT requirements identified for an individual or assigned duty section.
3.8.2.6. The CMT program will include comprehensive training covering all aspects of accountability operations and CAS processes integral to each task or process. CMT training outlines will include CAS tasks and processes to promote standardization.
During training, utilize standard CAS screens and CAS help screens to promote proficiency in CAS transaction processing. CAS access will be controlled and monitored by System Administrators (SA) until training is complete and documented.
3.8.2.7. Develops CMT training outlines which are reviewed by Munitions Supervision only after review and coordination by Wing Safety for ground and weapons safety adequacy and Quality Assurance for technical accuracy.
3.8.2.7.1. Training outlines will contain as a minimum:
3.8.2.7.1.1. Training Title.
3.8.2.7.1.2. Training objectives.
3.8.2.7.1.3. Student Instructional Material.
3.8.2.7.1.4. Training resources.
3.8.2.7.1.5. Instructional method.
3.8.2.7.1.6. Instructional guidance.
3.8.2.7.2. Close coordination with the local logistics/maintenance training flight is required when developing course curriculum and training outlines. Refer to AFMAN 36-2234, Instructional Systems Development.
3.8.2.8. All personnel will receive In-Garrison Expeditionary Site Plan (IGESP), Expeditionary Site Plan (ESP), and MEP (if applicable) training on their portion of these plans during CMT training.
3.8.2.9. CMT instructors will be designated in writing and will be CFETP qualified and technically proficient on all instructional tasks. CMT instructors may be assigned to the Munitions Training Element or other sections/elements.
3.8.2.10. CMT is scheduled and conducted according to the following guidelines:
3.8.2.10.1. Initial CMT academic training should normally be completed before practical training. Training must include:
3.8.2.10.1.1. Instruction in tasks required to accomplish the unit's IGESP, ESP, and MEP (if applicable) during transition to conflict.
3.8.2.10.1.2. All safety devices, features and hazards of the work environment IAWAFMAN 91-201 and applicable item technical orders.
3.8.2.10.1.3. Identification and description of components IAW the applicable item technical order.
3.8.2.10.1.4. Review of abbreviated inspection tasks and rapid assembly of components IAW T.O. 11A-1-63 and/or the specific item technical order (-63 are preferred).
3.8.2.10.1.5. Review of vehicle, AGE, SE, MMHE, TMDE, test set, and special tool specification, use, and operational maintenance requirements for each type build/operating locations.
3.8.2.10.1.6. Review of requirements and procedures for munitions security and storage.
3.8.2.10.2. Practical training normally begins when academic training is complete.
Practical training is administered by qualified and appointed CMT Instructors.
Conduct CMT in facilities or training areas usually dedicated to the munitions assembly or support operation being instructed and will include:
3.8.2.10.2.1. Use of facilities large enough to accommodate required training and associated SE.
3.8.2.10.2.2. Use of a practical training area with adequate office space and an academic classroom with appropriate heating and cooling.
3.8.2.10.2.3. Maximum duplication of realistic operating conditions to enhance training. Additional munitions practical training considerations for munitions include:
3.8.2.10.2.3.1. Familiarity with munitions serviceability criteria. Do not allow blanket rejection of training munitions during training operations solely because they are inert.
3.8.2.10.2.3.2. Familiarity with the operation of all available MMHE, AGE and SE used during operations. Pay particular attention to equipment not used on a routine basis. This training focuses on handling, utilization, loading procedures to include loading in/out of containers.
3.8.2.10.2.3.3. The training must emphasize set-up for mass assembly and innovate production techniques and organization (i.e., using Munitions Assembly Conveyor (MAC), trailer builds, dunnage builds, etc.) use of power tools and on-the-spot maintenance procedures (i.e., use of thread chasers, alignment devices, etc.). As a minimum, this phase includes:
3.8.2.10.2.3.3.1. Physical inspection of components according to T.O. 11A-1-63 or specific item T.O. (use 11A-11A-1-63 when procedures are included).
3.8.2.10.2.3.3.2. Use of inert components for this training is recommended.
If inert components are not available, live munitions may be used provided serviceability is not jeopardized and technical data or MAJCOM does not prohibit use.
3.8.2.10.2.3.4. Units with an alternate mission as specified in an approved Organizational Mission Directive (OMD) (i.e., TARRP) will ensure training reflects applicable tasks.
3.8.2.11. Units will use IMDS/G081 to track CMT.
3.8.3. Munitions Inspector Training:
3.8.3.1. Any 2W051, 2W071 or 2W091 munitions technician/supervisor may be trained, qualified, and appointed as a Munitions Inspector at the discretion of the Munitions Flight Chief if they have completed Munitions Inspector Training and Certification using the USAF Qualification Training Package (AFQTP) for Munitions Inspector Training and Certification located on the A4LW AFKN CoP and any local requirements (e.g., Senior Inspector Assessment, Quality Assurance evaluations, etc.).
3.8.3.1.1. Units may include an addendum to the munitions inspector AFQTP to address local inspector requirements or processes, however, the basic AFQTP will not
be changed or deviated from without approval of the 2W0X1 Air Force Career Field Manager (AFCFM).
3.8.3.1.2. Submit proposed changes to the munitions inspector AFQTP through their Lead MAJCOM to the 2W0X1 AFCFM for approval prior to implementation.
3.8.3.2. Quality Assurance Specialists (Ammunition Surveillance) with a GS-1910 series rating, and contractors or civil service personnel filling munitions inspectors‘ positions may also be appointed as a Munitions Inspector, provided they meet the training, qualification and appointment criteria of paragraph 3.8.3.1 and possess at least four years experience in an ordnance or munitions career field/job series/position (e.g., civilian munitions worker, Explosive Ordnance Disposal (EOD), Naval/Army/USMC Ordnance, Aircraft Armament, Nuclear/ICBM Munitions).
3.8.3.3. Document certification in the Training Business Area (TBA) (ITP journal entry), AF IMT 623A, AF IMT 1098, IMDS/G081, or other suitable documentation, standardized across the unit.
3.7.3.4. Utilize a ―Train-the-Trainer‖ concept to locally train and certify munitions inspectors. Munitions inspector trainers must be qualified and appointed munitions inspectors, 7-levels, and must possess a minimum of 2-years of continuous munitions inspection experience and hold an 836 SEI. Note that for all inspector/senior inspector training and qualification requirements, civilian and contractor personnel do not hold skill levels or special experience identifiers (SEI), however, they must meet 836 SEI requirements.
3.8.3.5. Award of SEI 836 requires Specialty Training Standard (STS) qualification, Munitions Inspector AFQTP completion, 8 months hands-on munitions inspection experience in any munitions workcenter, and supervisor‘s recommendation.
3.8.3.6. The senior munitions inspector must have two years continuous munitions inspection experience within the past 48 months or have attended a formal AETC or MAJCOM Munitions Inspection course within the past 48 months, and hold SEI 836.
3.8.4. NWRM Training: All personnel that are assigned NWRM duties will receive NWRM training IAW AFI 20-110 prior to handling any NWRM.
3.9. Static Display Munitions (SDM) and Inactive/Obsolete EOD Training Munitions