GROSS POSITIONING ERROR
2.6.4 NC Software 280 476-xx and 280 477-xx
NC Software 280 476-01 (export version 280 477-01)
Release: 05/99 Improvements:
nMP340: External interpolation
nMP1097, MP1098: Input range expanded from 1 to 1000 [m/s3] to 0.1 to 1000.0 [m/s3]
nMP1150 expanded: MP1150.1 Time duration for which monitoring functions must remain switched off; MP1150.2 Time duration for which monitoring functions must remain active
nMP2221: Monitoring the reference pulse of the spindle-speed encoder nMP2360, MP2361: Time constant for deceleration of spindle at
EMERGENCY STOP
nMP2391: Max. braking performance of spindle at EMERGENCY STOP nMP2393: Performance limit of spindle motor
nMP4030: Assignment physical/logical PL
nMP6585, MP6586: Monitoring the position of the rotary and additional linear axes during the tool measurement cycles
nMP7245: Disable auxiliary cycles
nMP7266.28: Center offset of sensor in main axis nMP7266.29: Center offset of sensor in secondary axis nMP7266.30: Spindle angle during calibration
nMP7411: One block/several blocks of sensor calibration data nMP7500: Cycle 19 with spatial angle C not equal to 0
nMP7530: Input of a formula for temperature compensation with swivel heads and tilting tables
nMP73xx: New default values for color settings
nHSC filter: The jerk value in MP1097.x is for bend changes
nIf the fast PLC input defined in MP4130.0 is set, the drive is no longer switched off automatically
nNew tilting axis combinations for spatial angle nM4181: NC program selected
nInput value of the rated frequency in the motor table for asynchronous motors increased from 999.9 Hz to 2000.0 Hz
nSeveral blocks of sensor calibration data in the tool table
nIn the manual operating modes, the highest axis feed is stored in D388 nMaximum spindle speed with spindle DSP was increased to 30 000 rpm.
nAfter the drive is switched on, the control waits 1.2 seconds for the "ready"
signal.
nFN17 ID230: Overwrite software limit switches
nFN18 ID990: Number of axes that are programmed in the current datum table
nModule 9035: Axis-specific handwheel superpositioning (M118) nModule 9040 and 9041: Reference values with calculated backlash
compensation
nModule 9122: Interrogate whether PLC axis has reached target position nModule 9151: The axis designations remain the same even if other machine
parameters are edited
nModule 9152: Selection of axis display, designation and traverse range nModule 9158: Limiting the maximum torque of an axis
nModule 9169: Define axes for which I32 does not cause drive switch-off (only TNC 426M / TNC 430M).
nModule 9175: Error code approach position active nModule 9275: Write ASCII data to the log book
nModule 9276: Write contents of operands to the log book nModule 9281: Set cursor on a line in the selected pallet table nCycle 33: Thread on taper
nThe values from the offset adjusting via code number 75368 are displayed in a pop-up window
nWith the machine parameters MP910.x to MP951.x, the coordinates can be transferred with the "Actual position capture" key.
nM136: Switching from mm/min to mm/spindle revolution nFeed rate with three decimal places
nNumber of transfer parameters for OEM cycles increased to 32
nThe last input value is suggested as default value with the "F" and "F MAX"
soft keys.
nM91, M92: Linear movements in the machine coordinate system with tilted working plane
nFile access in LSV2 protocol via Ethernet with TNCremo
nNew error number 1068 (Datum table?) for the function FN14: ERROR nCycle 207, 17, 18: Maximum input value expanded from Q239 to 99.9999
mm
nDIN/ISO: Cycles for tool measurement with G480 to G483 nCycle 247: Set datum during program run via datum table
nTraversing the reference marks is carried out with a new screen layout nSoft key "Optional stop": Stop program where M01 is programmed nSoft key "Edit datum table": Edit datum table
nError messages for the first spindle are marked with "S1," and for the second spindle with "S2"
nDSP error messages were classified
nM112: Feed rate limit so that jerk is not exceeded, exception: F MAX is programmed
NC Software 280 476-02 (export version 280 477-02)
Release: 05/99 Improvements:
nIn the format instructions for the large PLC window, special characters can be entered with /xYY.
nModule 9281: Datum shift and datum set can still be carried out, even if the line is disabled by an entry in LOCK.
nIn ASCII element fields, the text is interrupted word by word.
NC Software 280 476-03 (export version 280 477-03)
Release: 08/99 Improvements:
nMP21: Encoder monitoring for first and second spindle
nMP1089: Axis-specific jerk for Pass Over Reference Point mode
nMP2590, MP2591: Steepness of the braking ramp during an emergency stop
nMP4020: Automatically activate Return to Contour after an external emergency stop
nMP7281: Depiction of the NC program
nMP7500: Tilting-axis positioning during datum setting nMP7683: Display the AUTOSTART soft key
nNumerical range for M functions from 0 to 999
nAssignment of NC macros to M functions through a table nDescription of tilting-axis geometry in tables
nM4586: Autostart
nNCMACRO.SYS: Executing an NC macro in case of an error or after an external/internal stop
nNCMACRO.SYS: Executing a macro after leaving Pass Over Reference Point mode
nNCMACRO.SYS: Executing a macro when a block scan has been interrupted
nAfter reestablishing machine status, the status set by the PLC is checked to see if it agrees with the status calculated by the NC.
nPGM CALL and CYCLE CALL (cycles greater than 68) are calculated automatically with the look-ahead function and run without exact stop (FN20: WAIT FOR SYNC).
nThe integrated oscilloscope can record the jerk and the acceleration of the axes.
nW1018: Number of files opened by the PLC nW1020: Number of open files
nM4546: Second tool age has expired
nFN17 ID290: Activate tilting-axis geometry description nFN18 ID290: Ascertain tilting-axis geometry description nFN17 ID210: Tilted working plane in Manual mode
nFN18 ID210: Is tilted working plane in Manual mode active?
nFN17 ID230: Turn limit switch monitoring on and off nFN17 ID501: Write to REF-referenced datum table nFN18 ID501: Read from REF-referenced datum table nFN17 ID20: Switchover spindle 1 / spindle 2
nFN31: Switch range of traverse, axis assignment, axis display nFN32: Setting the datum
nModule 9044: Reading the spindle coordinates in 0.0001°
nModule 9097: Selecting the geometry description
nModule 9161, 9162: The bit for the spindle or the axis can be transferred with C-axis operation
nModule 9189: Shut down the control nModule 9291: Calling an NC macro
nStrings can be shown in the TABLE function
nBefore the PLC program is converted, the PLC outputs are reset.
nVarious LSV2 telegrams are entered in the log book.
nTwo M functions in one NC block
nNew NC blocks: SEL TABLE, SEL PATTERN and CYCL CALL PAT nCycle 208: Parameter Q342
nCycle 247: Coordinates always interpreted in reference coordinates nCycles 262, 263, 264, 265, 267: Thread milling
nCycle 209: Tapping with chip breaking
nCycles 410 to 418: Also function when a basic rotation is active.
nSample tables are copied into the appropriate directories with COPY SAMPLE FILES.
nMultiple empty coordinate fields in NC programs are skipped.
nIf a company logo is displayed, the control description is no longer shown.
NC software 280 476-04 (export version 280 476-04)
Release: 09/99
NC Software 280 476-05 (export version 280 477-05)
Release: 10/99 Improvements:
nMP2602, MP2604: Integral Phase Compensation - IPC
nTemperature compensation with M128 etc. through the description tables of the tilting-axis geometry
nThe selected geometry description is indicated in the program management.
nInput range of the STR column in the motor tables expanded
nA DSP error message appears if the ready signal is missing from the speed encoder inputs for vertical axes.
nDirection monitoring of digitally controlled spindles nM4179: Control is shut down
nM4230: NC start via LSV2 nM4231: NC stop via LSV2
nM4220: Error from PET table/F stop active nM4221: Error from PET table/NC stop active nM4222: Error from PET table/EM. STOP active
nModule 9002, 9003, 9005, 9008, 9009: Error code 24 (Module was called in the submit job or spawn job) added
nModule 9007: Diagnostic information of the PL
nModule 9040, 9041: Coordinate type 8 (temperature compensation from description tables) added
nModule 9087: Status of PLC error message
nModule 9098: Ascertain the active geometry description
nModule 9130: New error codes 1 (Invalid analog output) and 2 (Disabled analog output) added
nModule 9158: The torque of the active spindle can also be limited nModule 9189: The drive ready signal is removed
nModule 9196: Finding the PLC cycle time nImproved search function
nISO: A Q parameter can be entered for the feed rate after M128 or G80 nISO: The Q key of the numeral keypad or the ASCII keyboard may be used nWhen the control is shut down, the hard disk is put into sleep mode.
nCycle 440: Heat compensation
NC Software 280 476-06 (export version 280 477-06)
Release: 12/99 Improvements:
nMP420, MP430: Changes no longer lead to a control reset
nMP2221: Monitoring of rotational direction for spindle with integral DSP nMP2600: Input range changed
nMP6510: Second measuring error added
nMP7640, MP7641, MP7645 are no longer shown through code number 123 nAll machine parameters that can be changed by the PLC can be changed in
a running NC program.
nOverflows from multiturn encoders are entered in the NCDATA.SYS system file.
nBefore the PLC program is converted , the memories of the PLC outputs are reset.
nPointers to error messages are entered in the log book.
nM4547: T and G strobes with TOOL CALL nFN17 ID990: Orient spindle
nFN18 ID990: Find spindle angle
nHard disks larger than 3.25 MB are supported
nModule 9035: Transfer value 26 (jog increment limiting) added nModule 9060: Status of M functions
nModule 9186: Transfer value 6 (jog increment) added nModule 9300: Locking/releasing the pocket table nModule 9305: Pocket exchange in the pocket table
nModule 9310: Read the machine parameter from the run-time memory nModule 9320: Status of NC program end
nM140: Depart contour in the current tool-axis direction nM141: Suppress touch probe monitoring
nNew LSV2 telegrams
nCycle 204: A value with digits after the decimal point may be entered in Q255
nA German and an English machine parameter description, as well as the configuration files for CycleDesign, are saved in PLC:\JH.
nEvery NC setup is saved in its own directory and can be selected.
nM functions M0 to M999 are possible in Manual mode; M100 to M299 result in error messages
NC Software 280 476-07 (export version 280 477-07)
Release: 02/00 Improvements:
nMP812: Software limit switches also with M94, modulo display and encoders with EnDat interface
nMP2606: Influence following error during the jerk phase
nMP3030: Zero spindle speed when switching to another gear range nMP6500: Tool measurement with stationary spindle
nMP7261: Pockets in tool magazines 1 through 4
nMP7267: Position of the comment from the tool table in the pocket table nMP7620: Feed-rate smoothing
nMP7683: Display of pallet table and NC program
nUp to 4 tool magazines may be managed in the pocket table.
nEncoders with EnDat interface can be used as position encoders for rotary axes.
nMonitoring of the number of grating periods between the reference end position and the first reference mark
nIn a tilted working plane in Manual mode, more than one axis can be moved simultaneously, and the start key can be used to traverse the reference marks.
nIn the WAIT column of the table of M-function macros, you can determine if the NC should wait for acknowledgement from the PLC.
nWith the aid of the ”machine parameter subfile” column in the assignment table of the tilting-axis geometry description, a function for changing milling heads can be created.
n16 strings
nAfter the drive is switched on, the control waits 2 s for the ”ready” signal.
nModule 9097: Error codes 9 (Error in the MPFILE column), 10 (Error in the MP7500 column) and 11 (Error in the machine parameter subfile) added nModule 9031: Find the number of an entry in the pocket table
nModule 9032: Look for a free pocket in the tool magazine nModule 9036: Switch tools between tool magazines nCylindrical surface interpolation in a tilted working plane nSUPPORT soft key for remote diagnosis with TeleService
nA comment can be entered in the DOC column of the datum tables.
nM142: Delete modal program information nM143: Delete programmed basic rotation
nDisplay ”TNC 426/430 x” when control is switched on
nM109 or M110 are automatically cancelled when an OEM cycle ends or is cancelled.
NC Software 280 476-07 (export version 280 477-07)
Release: 02/00 Improvements:
nMP812: Software limit switches also with M94, modulo display and encoders with EnDat interface
NC Software 280 476-08 (export version 280 477-08)
Release: 05/00
NC Software 280 476-09 (export version 280 477-09)
Release: 05/00 Improvements:
nMP10: Change no longer results in a reset
nMP1095: Nominal position value filter for manual and automatic operating modes
nMP1396: Feedback control with velocity semifeedforward nMP1516: kV factor for velocity feedforward
nMP2170: Waiting time between switching on the drive and the drive’s standby signal
nMP2391: Max. braking performance of spindle during a powerfail nMP4020: Pass on simulated and disabled keys to NC and PLC windows nMP6572: Limit spindle speed in tool measurement cycles
nMP7230: Conversational language Russian
nMP7442: Number of the M function for the spindle orientation in cycles nMP7502: Functionality of M144/M145
nA maximum of 10 variables can be used in the description tables for the tilting-axis geometry.
nNumbers in hexadecimal and binary form in freely definable tables nNew error messages for FN14
nM4587: Feed rate limit not effective
nDuring powerfail: Attempt to reset PLC outputs and to maintain readiness for 3 seconds
nFN17 ID600: Factor for velocity semifeedforward
nFN17 ID600: Factor from MP1396 for velocity semifeedforward nFN18 ID20: Coordination between logical and geometrical axis nFN18 ID310: M144 active
nModule 9035: Status information of active range of traverse nModule 9061: Status of non-modal M functions
nModule 9066: Status of HEIDENHAIN inverter nModule 9133: Temperature of the LE
nModule 9279: Control reset
nM144: When an axis is moved, the kinematics are recorded in the display, but without compensatory motions.
nIncreased protection of the controls from unauthorized data accessing nIf the hardware contains flash EPROMs, the letter ”F” is displayed before
the NC software Id. Nr.
nWhen transferring an actual position capture to a datum table, it can be referenced to either the workpiece datum or the machine datum.
nWhen transferring measured values from the manual touch probe cycles to a datum table, they can be referenced to either the workpiece datum or the machine datum.
NC Software 280 476-10 (export version 280 477-10)
Release: 06/00
nMP6165: New probing function for the TS 632
nNew password AXISNUMBER for OEM.SYS, to limit the number of machine parameter indexes
NC Software 280 476-11 (export version 280 477-11)
Release: 07/00
nMP1087.x: Axis-specific jerk for Manual mode nMP7680 bit 12: Behavior of Cycle 28
nNew error message for FN14
nFN17 ID990: Axis shown on top of other axis due to tilting motion?
NC Software 280 476-12 (export version 280 477-12)
Release: 07/00
NC Software 280 476-13 (export version 280 477-13)
Release: 10/00
nMP110.x and MP111.x no longer result in a RESET
nMaximum input ranges for MP2391.x, MP2393.x, MP2395.x, MP2500.x, MP2501.x, MP2510.x and MP2511.x, MP6160, MP6161, MP6560, MP7442 expanded
nMP7500 bit 8: Recalculate the datum to the home position of the tilting element
nEnDat multiturn encoders as position encoders
nActual-to-nominal value transfer only occurs in the affected axis during an erasable positioning error
nFN18 ID290: Determine the value of the bits in MP7500 nModule 9146: Saving and reestablishing actual position values nModule 9147: Bit from W1032 is reset
nModule 9157: Drive controller status
nBehavior during calibration of the touch-trigger probe with infrared transmission changed
nTool-by-tool execution of pallet tables nCycle 431: Establish spatial angle
nCycle 247: Set a datum from a datum table as the datum in the REF system NC Software
280 476-14 (export version 280 477-14)
Release: 11/00
nFN18 ID214: Ascertain tolerance in Cycle 32 or MP1096