MANAGER’S FUNCTION
OPERATION ON MANAGER’S FUNCTION SCREEN Operation Procedure
Input the password on the normal function menu (as explained on the preceding page) to display the SERVICE FUNCTION screen.
Press the switch (3) for more than two second
Press switch (3)
*1:With chopper
*2:Chopper-less
Press switch (3)
Press switch (3)
Press switch (3)
*2
*1
Press switch (3) Press switch (3)
Press switch (3)
Press switch (3)
Press switch (3) Switch (1) Switch (2)
Switch (3) Switch (4)
Travel speed limiter level setting screen
Over speed alarm setting screen
Travel power control
level setting screen Tilt power control
level setting screen Planned maintenance hour setting screen
Temporary cancellation brush wear warning Clock setup selection screen
Press switch (4) Select “YES” and press switch (3) Select “NO” and press switch (3)
Multiple hour meter mode Power select function Normal function
Lift power control level setting screen Manager’s function
Manager’s Function Indicated Screen
1. Selection of hour meter type to be displayed
Press switch (4) to select the hour meter type to be displayed.
(1) Key ON hour meter: Indicate the total key ON hours.
(2) Traveling/material handling hour meter: Drive/pump motor ON hours
(3) Traveling or material handling hour meter: Total of drive or pump motor ON hours (4) Odometer: Total traveling distance
(5) Lap hour meter: Lap time at key ON (6) Trip meter: Trip traveling distance
(7) Planned maintenance hour meter: Accumulated hours total in key on-state since last maintenance.
Press switch (4) Press switch (4)
Press switch (4) Press switch (4)
Press switch (4) Press switch (4)
Press switch (4) Switch (1) Switch (2)
Switch (3) Switch (4)
(1) Key on hour meter
(3) Traveling or material handling hour meter
(3) Traveling and material handling hour meter (4) Odometer
(5) Lap hour meter (6) Trip meter
(7) Planned maintenance hour meter
The lap time and trip meter can be reset by pressing switch (1) for two seconds or more.
2. Selecting the power select mode ( S , P or H ) Press switch (3) on the normal function screen to select the desired power mode by shifting to the corresponding indicator position.
S : To hold down the output and realize operation of long time
P : Power equivalent to the maximum power of previous model
H : 15% increase in performance under loaded condition
• Pattern1: When nothing is set on the POWER CONTROL SET UP SELECTION screen
Each time switch (3) is pressed, the selected mode position shifts to the right in the order shown below:
S → P → H → S and so on
• Pattern2: When setting is made on the POWER CONTROL SET UP SELECTION screen Each time switch (3) is pressed, the selected mode shifts to the right as shown below:
S → P → H → S P H → S → P and so on
When all modes are enclosed in squares, the control is made by the mode selected on the POWER CONTROL SET UP SELECTION screen.
TRAVEL SPEED LIMITER LEVEL SETTING SCREEN Use this screen to set the travel speed limiter level. Indicator lights when travel speed limit set is seven or less.
(1) Press switch (1) to decrease the travel speed limiter level.
(2) Press switch (2) to increase the travel speed limiter level.
(3) Press switch (3) to go to the next screen, (OVERSPEED ALARM SET screen).
OVERSPEED ALARM SETTING SCREEN
This screen sets the traveling speed level for overspeed alarming. To call the OVERSPEED ALARM SET screen from the TRAVEL SPEED LIMITER LEVEL SETTING screen, press switch (3) once.
(1) Press switch (1) to decrease the set traveling speed.
(2) Press switch (2) to increase the set traveling speed.
(3) Press switch (3) to go to the next screen, POWER CONTROL set up selection screen.
Power select indicator Switch (3)
Switch (1) Switch (2)
Switch (3) Switch (4)
Switch (1) Switch (2)
Switch (3) Switch (4) Vehicle speed setting for speed alarm
POWER CONTROL SET UP SELECTION SCREEN
This screen sets the travel and material handling power control levels independently.
Press switch (3) on the OVERSPEED ALARM SETTING screen to go to the POWER CONTROL SET UP SELECTION screen.
(1) Press switch (1) on the POWER CONTROL SET UP SELECTION screen, select “YES” and press switch (3) to go to the TRAVEL POWER CONTROL LEVEL SETTING screen.
(2) Press switch (2) on the POWER CONTROL SET UP SELECTION screen, select “NO” and press switch (3) to go to the LIFT POWER CONTROL LEVEL SETTING screen. (with chopper) Go to the next menu in case of the chopper-less type.
TRAVEL POWER CONTROL LEVEL SETTING SCREEN This screen sets the travel power control levels.
Press switch (1) or (2) on the POWER CONTROL SET UP SELECTION screen, select “YES” (with chopper) or “NO”
(chopper-less) and press switch (3) to go to the TRAVEL POWER CONTROL LEVEL SETTING screen.
1) Press switch (1) to decrease the set level.
2) Press switch (2) to increase the set level.
3) Press switch (3) to go to the next screen, LIFT POWER CONTROL LEVEL SETTING screen.
(with chopper)
It goes to the CLOCK SET UP SELECTION screen, in case of chopper-less type models.
LIFT POWER CONTROL LEVEL SETTING SCREEN (WITH CHOPPER)
This screen sets the lift power control levels.
Press switch (2) on the POWER CONTROL SET UP SELECTION screen, select “NO” and press switch (3) to go to the LIFT POWER CONTROL LEVEL SETTING screen.
1) Press switch (1) to decrease the set level.
2) Press switch (2) to increase the set level.
3) Press switch (3) to go to the next screen, TILT POWER CONTROL LEVEL SETTING screen.
(with chopper)
TILT POWER CONTROL LEVEL SETTING (WITH CHOPPER)
This screen sets the tilt power control levels.
Press switch (3) on the LIFT POWER CONTROL LEVEL SETTING screen to go to the TILT POWER CONTROL LEVEL SETTING screen.
(1) Press switch (1) to decrease the set level.
(2) Press switch (2) to increase the set level.
(3) Press switch (3) to go to the next menu, CLOCK SET UP SELECTION screen.
Select “YES”, and press switch (3)
Press switch (3)
Press switch (3)
Switch (1) Switch (2)
Switch (3)
Traveling power control level setting screen
Lift power control level setting screen (with chopper) Switch (4)
Tilt power control level setting screen (with chopper)
PLANNED MAINTENANCE HOUR SETTING SCREEN