5 Commissioning Process
5.2 Data Configuration at OMC
5.2.6 Physical Configuration
5.2.6.1 Configure BBU Rack
Configuration premix:” District” an d “SDR” no des sho uld h ave bee n crea ted in the configuration tree of the Configuration Management interface:
ZTE Confidential Proprietary © 2012 ZTE CORPORATION. All rights reserved. 19 Configuration steps:
1. Log on to OMC Client.
2. Select Views --> Configuration Management f rom the men u b ar to o pen the Configuration Management interface.
3. Unfold the configuration tree in the le ft of the Config uration Management interface and select the Physical Configuration node under B8200.
4. Right click on the Physical Configuration node and select Add BBUB Rack from the pop-up menu, as shown below.
Figure 5-19 Select “Add BBUB Rack” Option
5. In the Add BBUB Rack interface that displays, select BBUB Rack in t he Rack Type field and click OK button to finish the operations, as shown in Figure 5-.
Figure 5-20 “Add 8200 W100 Rack” Interface
ZTE Confidential Proprietary © 2012 ZTE CORPORATION. All rights reserved. 20
5.2.6.2 Configure BBU Board
Configuration Premix: The BBU rack has already been configured.
Configuration steps:
1. Log on the OMC Client.
2. Select Views --> Configuration Management from the menu ba r to open the Configuration Management interface.
3. Unfold th e configuration t ree in th e l eft of the Configuration Management interface to find the BBU Ra ck node and click it. Th en the BBU Ra ck diagram will be displayed in the right of the interface.
4. Right click on a blank slot in the BBU Rack diagram and select a correct board type from the pop-u p menu to configur e a board in the corresponding slot, as shown below.
Figure 5-21 “Add Board” Option
Figure 5-22 Add Board
ZTE Confidential Proprietary © 2012 ZTE CORPORATION. All rights reserved. 21 Note:
1. In adding XB P boards, the system first adds a g roup of the boa rds by default.
Then the XBP parameter configuration in terface pops up, enabl ing the proper parameters to be set.
2. The CCA is a controlli ng board, so it must be conf igured in active/standby mode.
3. The boards can be added in any order.
5.2.6.3 Configure Physical Parameter
Configuration steps:
1. Log on to OMC Client.
2. Select Views --> Configuration Management from the menu bar to open the Configuration Management interface.
3. Unfold the configuration tree in t he left of the Configuratio n Manag ement interface to find the Physical Configuration node and click it. Then the Physical Configuration interface will be displayed in the right of the in terface, as shown below.
4. Set each parameter in the physical parameter tab p age and then click the button in the tool bar to save the modifications.
Figure 5-23 Physical Configuration Interface-physical parameter
ZTE Confidential Proprietary © 2012 ZTE CORPORATION. All rights reserved. 22
5.2.6.4 Configure AGW Static Route
Configuration premix: physical parameter tab page has already been configured.
Configuration Steps:
1. Log on to OMC Client.
2. Select Views --> Configuration Management from the men u bar to open the Configuration Management interface.
3. Unfold the co nfiguration tree in the left of the Config uration Man agement interface to find the Physical Configuration node and click it. Then the Physical Configuration interface will be displayed in the right of the interface, as shown in Figure 5-23
4. Select “Static Route” tab page, as shown in Figure 5-24
Figure 5-24 Physical Configuration Interface- Select “Static Route” Tab Page
5. Right cli ck th e yellow bar unde r Static Route tab pa ge to move out” Add Static Route” dialog ue box, set each para meter in the dialogue box, and pre ss OK to confirm the setting, as shown in Figure 5-25
Figure 5-25 Physical Configuration Interface-“Add Static Route” dialogue box
ZTE Confidential Proprietary © 2012 ZTE CORPORATION. All rights reserved. 23 6. Parameter configuration in “Add Static Route” dialogue box is completed, as shown
in Figure 5-26. (Several static routes can be added at once.)
Figure 5-26 Physical Configuration Interface-“Add Static Route” is Completed
5.2.6.5 Configure CCA Board External IP
Configuration premix: CCA board has already been added.
Configuration steps:
1. Log on OMC Client.
2. Select Views --> Configuration Management f rom the men u b ar to o pen the Configuration Management interface.
ZTE Confidential Proprietary © 2012 ZTE CORPORATION. All rights reserved. 24 3. Unfold the configuration tree in the le ft of the Config uration Management interface
to find the BBU Rack no de and cli ck it. Then the BBU Rack diagram will be displayed in the right of the interface.
4. Right cli ck o n CCA boa rd in the BB U Ra ck dia gram and sel ect Config ure BT S External IP from the pop-up menu, as shown below.
Figure 5-27 B8200 Physical Configuration -CCA Board External IP
5. After the Configure BTS External IP interface displays, set external IP, IP mask and next hop and click OK button to close the interface.
Figure 5-28 B8200 Physical Configuration-CCA Board External IP
Note:
ZTE Confidential Proprietary © 2012 ZTE CORPORATION. All rights reserved. 25 1. IP address of CCA must be the IP address shown in NetNumen for B8200 and it
must be unique in the network managed by NetNumen.
2. Next hop must be in the same segment with CCA external IP but they must not be the same.
3. Only one piece of CCA board needs IP configuration. The rest of the CCA boards will automatically adopt the configured IP.
5.2.6.6 Configure XBP Board Parameters
Configuration premix: XBP board has already been added. (Note t hat BBU and RRU are connected via XBP board. One XBP board can be connected with several RRUs.
Configuration steps:
1. Log on to OMC Client.
2. Select Views --> Configuration Management from the menu bar to open the Configuration Management interface.
3. Unfold the configuration tree in t he left of the Configuratio n Manag ement interface to find the BBU Rack node and click it. Then the BBU Rack diagram will be displayed in the right of the interface.
4. Right click on XBO board i n the BBU Rack diagram and select Configure XBP Parameters from the pop-up menu, as shown below.
Figure 5-29 BBU Basic Information Configuration-XBP parameters
5. After the Con figure WBPM Parameters interface displays, set the parameters and click OK button to close the interface.
Figure 5-30 BBU Basic Information Configuration-XBP parameters
ZTE Confidential Proprietary © 2012 ZTE CORPORATION. All rights reserved. 26
5.2.6.7 Configure XBP Board R6 IP
Configuration steps:
1. Log on to OMC Client.
2. Select Views --> Configuration Management f rom the men u b ar to o pen the Configuration Management interface.
3. Unfold the configuration tree in the le ft of the Config uration Management interface to find the BBU Rack no de and cli ck it. Then the BBU Rack diagram will be displayed in the right of the interface.
4. Right click on XBO board in the BBU Rack diagram and select Configure XBP R6 IP from the pop-up menu, as shown in Figure 5-31
Figure 5-31 Physical Configuration Interface- XBP R6 IP
ZTE Confidential Proprietary © 2012 ZTE CORPORATION. All rights reserved. 27 5. After the Co nfigure MPXM External IP interface displays, set the parameters and
click OK button to close the interface.
Figure 5-32 Physical Configuration Interface- XBP R6 IP
Note:
1. Next hop must be in the same segment with XBP R6 IP and Next hop must be different from XBP R6 External IP.
2. Next hop depends on AGW IP address and AGW Static Route.
3. XBP Next hop here should not be modified.
5.2.6.8 Configure RRU Rack
Configuration premix:
1. District node has been created.
2. B8200 node has been created in the configuration tree;
Configuration steps:
1. Log on OMC Client.
2. Select Views --> Configuration Management from the menu bar to open the Configuration Management interface.
3. Unfold the configuration tree in t he left of the Configuratio n Manag ement interface and select the Physical Configuration node under B8200.
4. Right click on the Physical Configuration node and select Add RRU Rack from
ZTE Confidential Proprietary © 2012 ZTE CORPORATION. All rights reserved. 28 the pop-up menu, as shown in Figure 5-33.
Figure 5-33 “Add RRU Rack” Option
5. In the Add RRU Rack interface that displays (Figure 5-34), set such parameters as WBPM unit, WBPM po rt and subsystem and click OK b utton to finish the operations.
Figure 5-34 Add RRU Rack Interface
ZTE Confidential Proprietary © 2012 ZTE CORPORATION. All rights reserved. 29
5.2.6.9 Configure RRU Board
Configuration premix: RRU rack has been configured.
Configuration steps:
1. Log on to OMC Client.
2. Select Views --> Configuration Management from the menu bar to open the Configuration Management interface.
3. Unfold the configuration tree in t he left of the Configuratio n Manag ement interface to find the RRU Ra ck node and click it. Then the RRU Ra ck diagram will be displayed in the right of the interface.
4. Right cli ck on a blank slot in the RRU Rack diag ram and sel ect Add WTRX Board from the pop-up menu to configure a board in the corresponding slot, as shown in Figure 5-35 and Figure 5-36
Figure 5-35 Add RRU Board
Figure 5-36 Add RRU Board
ZTE Confidential Proprietary © 2012 ZTE CORPORATION. All rights reserved. 30 Note: In adding WTRX board, the Configure TRX Parameters interface will display, where you can set the parameters.
5.2.6.10 Configure TRX Board Parameters
Configuration premix: RRU rack and TRX board have already been configured. ( Note that there are two ways to con figure TRX parameters: when the WT RX board is added and after the board is added. Here the second one is discussed.)
Configuration steps:
1. Log on to OMC Client.
2. Select Views --> Configuration Management from the menu bar to open the Configuration Management interface.
3. Unfold the configuration tree in t he left of the Configuratio n Manag ement interface to find the RRU Ra ck node and click it. Then the RRU Ra ck diagram will be displayed in the right of the interface.
4. Right click on WPTR board in the RRU Rack diagram and select Configure TRX Parameters from the pop-up menu, as shown in Figure 5-37
Figure 5-37 Configure TRX Parameters Option
ZTE Confidential Proprietary © 2012 ZTE CORPORATION. All rights reserved. 31 5. After the Co nfigure TRX Parameters interface (Figure 5-38) displays, set the
parameters and click OK button to close the interface.
Figure 5-38 Configure TRX Parameters Interface
Note: If 2 * 4 RFs have to be configured, the antenna mode should be set as 2T4R, which means 2 transmitters and 4 receivers.