You use MMC: 726 to set a series of VM/AA Options. There are eight main options for programming and several sub-options. Many of them are YES/NO. Others require a few numbers or letters of the alphabet. While you use the default settings in almost all cases, it is best to check that the settings are the ones they are supposed to be.
When programming MMC: 726, you use the following program keys:
To set VM/AA options:
1. Press TRSF then dial 726.
The display shows the EXT for DN1 option and its default setting YES:
2. If the setting is as shown above:
a. Press UP to go to the next option.
b. Go on to the next numbered step.
If the setting is not as shown above:
a. Press the RIGHT softkey to move the cursor to the bottom line of the display.
b. Press UP or DOWN to change NO to YES.
c. Press the RIGHT softkey to move the cursor to the top line of the display.
Purpose Key
Scroll through a set of options UP and DOWN arrows
Enter selection Keypad
Move cursor right and left RIGHT and LEFT Softkeys Move cursor from top to bottom line on
display (or vice versa)
RIGHT and LEFT Softkeys
Store data and advance to next MMC SPK
Clear entry HOLD
Store and exit TRSF
Inputs the letter A A
Inputs the letter B B
Inputs the letter C C
EXT FOR DN1 YES
d. Press UP to go to the next option.
e. Go on to the next numbered step.
2. The display shows:
Follow the directions given in step 1, depending on whether the setting is as shown or not as shown.
3. The display shows:
Follow the directions given in step 1, depending on whether the setting is as shown or not as shown.
4. The display shows:
Follow the directions given in step 1, depending on whether the setting is as shown or not as shown.
5. The display shows:
Follow the directions given in step 1, depending on whether the setting is as shown or not as shown.
6. The display shows:
If the setting is as shown above:
a. Press UP to go to the next option.
b. Go on to step 7.
If the setting is not as shown above:
a. Press the RIGHT softkey to move the cursor to the bottom line of the display.
b. Press C.
c. Press UP to go to the next option.
d. Go on to step 7.
7. The display shows:
TRK FOR DN1 YES
EXT FOR DN2 NO
TRK FOR DN2 NO
SEPARATOR NO
DISCONECT SIGNAL C
CALL TYPE ID DIRECT CALL:*
If the setting is as shown above:
a. Press the RIGHT softkey to move the cursor to the bottom line of the display.
b. Go on to step 8.
If the setting is not as shown above:
a. Press the RIGHT softkey to move the cursor to the bottom line of the display.
b. Press *.
c. Go on to step 8.
8. Press UP for the next option.
The display shows:
9. If # is not already the setting, press the RIGHT softkey to move the cursor to the bot-tom line of the display. Then press #.
10. Press UP for the next option.
The display shows:
11. If # is not already the setting, press the RIGHT softkey to move the cursor to the bot-tom line of the display. Then press #.
12. Press UP for the next option.
The display shows:
13. If # is not already the setting, press the RIGHT softkey to move the cursor to the bot-tom line of the display. Then press #.
14. Press UP for the next option.
The display shows:
15. If # is not already the setting, press the RIGHT softkey to move the cursor to the bot-tom line of the display. Then press #.
16. Press UP for the next option.
The display shows:
CALL TYPE ID ALL FWD CALL:#
CALL TYPE ID BSY FWD CALL:#
CALL TYPE ID NOA FWD CALL:#
CALL TYPE ID RECALL:#
CALL TYPE ID DIR TRK CALL:6
17. If 6 is not already the setting, press the RIGHT softkey to move the cursor to the bot-tom line of the display. Then press 6.
18. Press UP for the next option.
The display shows:
19. If # is not already the setting, press the RIGHT softkey to move the cursor to the bot-tom line of the display. Then press #.
20. Press UP for the next option.
The display shows:
21. If # is not already the setting, press the RIGHT softkey to move the cursor to the bot-tom line of the display. Then press #.
22. Press UP for the next option.
The display shows:
23. If * is not already the setting, press the RIGHT softkey to move the cursor to the bot-tom line of the display. Then press *.
24. Press the RIGHT softkey TWICE and then press UP to go to the next option.
The display shows:
If the setting is as shown above:
a. Press the RIGHT softkey to move the cursor to the bottom line of the display.
b. Go on to step 25.
If the setting is not as shown above:
a. Press the RIGHT softkey to move the cursor to the line with the setting.
b. Press B.
c. Press A.
d. Go on to step 25.
NOTE: A, B, and C are the first three keys in the bottom row of the function keys.
25. Rotate through the options for PROGRESS TONE ID by pressing UP.
CALL TYPE ID OVERFLOW:#
CALL TYPE ID DID CALL:#
CALL TYPE ID MESSAGE CALL:*
PROGRESS TONE ID DIAL TONE:BA
They should be as displayed below:
26. Do one of the following:
• Press TRSF to store and exit.
OR
• Press SPK to store and advance to the next MMC.
PROGRESS TONE ID BUSY TONE:4
PROGRESS TONE ID RINGBACK TONE:5
PROGRESS TONE ID DND NO MORE:6
PROGRESS TONE ID HDSET ANSWER:3
PROGRESS TONE ID SPKER ANSWER:3