rfoinfos cesorrectn
am
tion
in th
is d
c o en um C t.
py o ht b rig V y sw olk ge a A n G.
– Touch the field or button on the screen for “GUIDED FUNC‐
TIONS”.
– Confirm with > button.
– Select one after the other:
♦ Brand
♦ Type
♦ Model year
♦ Engine code
– Confirm vehicle identification.
– Select one after the other:
♦ “Radio system”.
♦ “Reading radio code”
– Read code according to the information of “GUIDED FUNC‐
TIONS”.
– Finish code reading as follows:
– Press “GoTo” button on display -arrow-.
– Press the “End” button on display.
– Press “End” button in End menu.
– Switch off ignition and separate diagnostic connections.
4.38 Radio/navigation system: Activate anti-theft coding
4.38.1 Volkswagen radio and navigation sys‐
tems
The radio units and radio-navigation systems are supplied with a security code.
Security code means that each unit with an anti-theft coding is programmed with its own code number.
This fixed code is not active when leaving the factory.
Note
♦ The safety code can be read from a central database using the vehicle diagnostic tester ⇒ page 139 .
♦ If SAFE appears on display when the radio is switched on, the radio is locked! The radio must remain switched on for one hour, the lock will then be released. The code can now be en‐
tered again.
Activate fixed code on “radio system RCD 200” as follows:
– Switch radio on.
te Pro
On display appears “SAFE” and after three seconds “1000”.
– Enter first digit of four-digit code using station button 1 -1-.
Enter 2nd digit using station button 2, etc.
– Confirm code entry by pressing the two buttons -2- for 2 sec‐
onds.
The radio is ready for use.
Note
♦ If the radio is removed or the vehicle battery disconnected, you will not have to enter the anti-theft coding manually, as the code number is stored in the vehicle when first entered.
♦ If the radio is installed in another vehicle, the code numbers do not match and the code must be entered manually again.
Activate fixed code on “radio system RCD 300” and “radio system RCD 500” as follows:
– Switch on radio navigation system using press button -1-.
– “SAFE” appears on digital display.
– After approx. 3 seconds “1000” appears on display.
– With the help of multi-function buttons -A- enter code number applied on radio card.
On display the position of the code number digit to be entered will be shown next to the four multi-function buttons, by a -X-.
– Press the multi-function button until the correct number ap‐
pears in the centre of the display -B-.
– Once the number has been entered correctly, operate multi-function button -D- next to the word ENTER.
The radio is ready for use again and switches to the previous op‐
erating mode.
Activate fixed code on "radio-navigation system MFD 2" as fol‐
lows:
– Switch on radio navigation system using press button -1-.
The security code can be found on the unit card.
– Enter code by turning rotary/push button -2- until number re‐
quired on number list -3- is highlighted and confirm each number by pressing the button briefly.
– Confirm code by turning rotary/push button -2- until “OK” on number list -3- is highlighted and confirm by pressing the but‐
ton briefly.
If the correct code has been entered, the actual radio frequency will appear after a short “learning phase”.
The LED on the top right of the radio-navigation system must flash when the ignition key is removed.
If the diode flashes, the radio navigation system is ready-for-use and the anti-theft coding is activated.
4.38.2 Blaupunkt navigation and radio system
“TravelPilot DX-R4/RN S4”
The radio units and radio-navigation systems are supplied with a fixed code. Fixed code means that each unit with an anti-theft
4. Descriptions of work
141
te Pro t c b ed co y y p h rig C t.
p o iny fog pr r a iv et r o o c m m
re
, ines paosrpupl iac rtor in w
hole, is not pe
rmitted unless autho rised b
y Volkswagen AG.Volkswagen AG does not g
uarantee or ac
cept a nylia
bi lity w
ith res pe
ct to the rfoinfos cesorrectn
am
tion
in th
is d
c o en um C t.
py o ht b rig V y sw olk ge a A n G.
coding is programmed with its own code number. This fixed code must be activated after installing.
On the Blaupunkt system “TravelPilot DX-R4/RN S4” activate the fixed code as follows:
The security coding of the ready to play radio is not activated until the fixed code is entered. The fixed code is to be activated as follows:
– Switch on radio navigation system using press button -5-.
– The coding is to be activated in the set-up menu “SECURITY”
-arrow- as follows:
A “basic” or “function menu” appears.
– Press button MEN -3- “TWICE”.
The system switches to the set-up menu.
If the setting menu of an audio source or navigation menu is al‐
ready active:
– Press button MEN -3- “ONCE”.
The system switches to the set-up menu.
To perform settings and to select menu options,
– Move the selection bar using the right rotary/push button -4-.
– Select the menu option “SECURITY” -arrow-.
te Pro t c b ed co y y p h rig C t.
p o in y fo g pr r a iv et r o o c m m
re
s, in pseorpupl iac
artor in w hole, is
not pe
rmitted unless autho rised b
y Volkswagen AG.Volkswagen AG does not g
uarantee or ac
cept a nylia
bi lity w
ith res pe
ct to the rfoinfoss conerrect
am
tion
in th
is d
c o en um C t.
py o ht b rig V y sw olk ge a A n G.
– Select the menu option “CODE” in the set-up menu “SECUR‐
ITY” and press rotary/push button -4-.
– Enter number code by turning the right rotary/press button in the number display -arrow 1-, mark the numbers one after the other and confirm entry after each number by pressing the right rotary/press button briefly.
Note
If an incorrect number has been entered, select the “Reset symbol
←”, and press ESC button -2 -.
– Perform the following procedure:
– If the code has been entered completely, confirm entry by se‐
lecting the “Return symbol” -2- with the rotary/push button and by pressing the button.
If the correct code number has been entered, the actual status will appear after a short “learning phase” behind “CODE”.
♦ Basic setting is “OFF”, means the code is not activated.
♦ Basic setting is “ON”, means the code is activated.
4. Descriptions of work
143
te Pro
On the radio system "Sound System" for vehicles for USA and Canada, activate the fixed code as follows:
– Switch radio on.
The unit automatically displays "SAFE" and then "1000". For this no buttons are used.
– With the help of station buttons 1 to 4 enter code number ap‐
plied on the radio card. Use button 1 to enter the first digit of the code number, button 2 to enter the 2nd digit and so on.
– Then press arrow button located above FAD button and hold, until the anti-theft coding is activated. This is indicated by a brief sound.
If the code number has been entered correctly into the radio unit, a radio frequency appears on display.
On the radio system "Premium Sound System" for vehicles for USA and Canada, activate the fixed code as follows:
– Switch radio on.
The unit automatically displays "SAFE" and then "1000". For this no buttons are used.
– With the help of station buttons 1 to 4 enter code number ap‐
plied on the radio card. Use button 1 to enter the first digit of the code number, button 2 to enter the 2nd digit and so on.
– Then press the station button, located below "OK" indicated on display (usually this is the last station button) and hold until the anti-theft coding is activated. This is indicated by a brief sound.
If the code number has been entered correctly into the radio unit, a radio frequency appears on display.