The error type is followed by Error Point
1) Serviceman Call Errors (Pxx)
Error Type P03 [Clamp motor lock]
Description
P03-xxx
!!System Error!!
Press Reset Key
If Recovery has Failed, Call Service To reset
display Press Reset Key
Error Point Error Conditions
500 Clamp sensor is OFF after the completion of the clamp unit initialization or home positioning movement.
501 Clamp sensor does not go OFF within 1 second from the time the clamp motor operates.
502 Clamp sensor does not go ON within 2.5 seconds from the time the clamp motor operates.
504 At the start of Clamp plate open action, the detection of clamp sensors is OFF.
505 At the start of print drum Position-A compensation movement, the detection of clamp　sensor is OFF.
506 At the start of Clamp unit Home-positioning movement, the detection of clamp sensor is ON.
507 Clamp sensor is OFF after the clamp open action is completed.
508 Clamp sensor is ON after the Position-A compensating movement is completed.
[ 15-8 ] 15-8 ] KZ30 (Rev. 1.2)
Imagetec Solutions Australia
Error Type P04 [Ink overflow]
Description
P04-xxx
!!System Error!!
Press Reset Key
If Recovery has Failed, Call Service To reset
display Press Reset Key after correcting the ink overflow condition. (No ink on the ink overflow sensor.)
Error Point Error Conditions
513 The overflow sensor is ON for a set number of times in succession during the 10-millisecond interval overflow-sensor check.
Error Type P12 [Master disposal area motor lock]
Description
P12-xxx
!!System Error!!
Press Reset Key
If Recovery has Failed, Call Service To reset
display Press Reset Key.
Error Point Error Conditions
300 Overload on the Master removal motor.
Error Type P13 [Cutter motor lock]
Description
P13-xxx
!!System Error!!
Press Reset Key
If Recovery has Failed, Call Service To reset
display Press Reset Key.
Error Point Error Conditions
221 The cutter HP switch and cutter stop position switch are both ON at the same time.
231 Cutter HP switch does not go OFF within 500 milliseconds after the cutter operation started from the HP position.
232 Cutter stop position switch does not go ON even after 2 seconds after the cutting movement
Error Type P19 [Master making area motor lock]
Description
P19-xxx
!!System Error!!
Press Reset Key
If Recovery has Failed, Call Service To reset
display Press Reset key or turn the power OFF and ON.
Error Point Error Conditions
207 TPH position sensor status did not change even after the TPH pressure motor activated for 2 seconds.
Error Type P24 [Inking motor lock]
Description
P24-xxx
!!System Error!!
Press Reset Key
If Recovery has Failed, Call Service To reset
display Press Reset key or turn the power OFF and ON.
Error Point Error Conditions
539 Inking-motor FG sensor status does not change within 20 milliseconds after the inking-motor is activated.
Error Type P96 [Data not input]
Description
P96-xxx
!!System Error!!
Press Reset Key
If Recovery has Failed, Call Service To reset
display Input the parameters using test mode.
Error Point Error Conditions
171 TPH resistance value not input.
Error Type P14 [Scanner error]
Description
P14-xxx
!!System Error!!
Press Reset Key
If Recovery has Failed, Call Service To reset
display Press Reset key or turn the power OFF and ON.
Error Point Error Conditions
104 Offset adjustment error.
125 A/D reference adjustment unfinished in time.
126 Gain adjustment not unfinished in time.
[ 15-10 ] 15-10 ] KZ30 (Rev. 1.2)
Imagetec Solutions Australia
Error Type P97 [PC card access error]
Description
P98-xxx
!!System Error!!
Press Reset Key
If Recovery has Failed, Call Service To reset
display Turn power OFF and ON.
Error Point Error Conditions
939 PC card not inserted.
940 PC card device data double ID error (data error as PCMCIA card).
941 PC device error (not detected as PC card).
942 File production error (same file name already exists).
943 PC card not formatted correctly.
944 PC card ID error.
945 PC card error (detected as PC card, but unable to make access).
946 PC card capacity error (not enough blank area).
990 File does not exist in the specified drive.
991 Accessed into a non-opened file).
992 File pointer to save the data is already in use.
993 Read address is not correctly set up.
994 File delete arror (file is not correctly deleted).
Error Type P98 [Hardware error]
Description
P98-xxx
!!System Error!!
Press Reset Key
If Recovery has Failed, Call Service To reset
display Turn power OFF and ON.
Error Point Error Conditions
002
No reply from optional neoROSA. If neoROSA signal is detected at machine power ON, but if the PCB communication terminates and P98-069 error is detected, the error point is rewrote to this P98-002 error message.
005 Hardware error
EEPROM check-sum error
Error Type P98 [Hardware error]
Description
P98-xxx
!!System Error!!
Press Reset Key
If Recovery has Failed, Call Service To reset
display Turn power OFF and ON.
Error Point Error Conditions
068 Communication error between neoROSA and MCTL PCB (04) - on MCTL PCB side.
069 Communication error between neoROSA and MCTL PCB (05) - on MCTL PCB side.
070 Communication error between neoROSA and MCTL PCB (06) - on MCTL PCB side.
071 Communication error between neoROSA and MCTL PCB (07) - on MCTL PCB side.
072 Communication error between neoROSA and MCTL PCB (08) - on MCTL PCB side.
073 Communication error between neoROSA and MCTL PCB (09) - on MCTL PCB side.
074 Communication error between neoROSA and MCTL PCB (10) - on neoROSA side.
075 Communication error between neoROSA and MCTL PCB (11) - on neoROSA side.
076 Communication error between neoROSA and MCTL PCB (12) - on neoROSA side.
077 Communication error between neoROSA and MCTL PCB (13) - on neoROSA side.
078 Communication error between neoROSA and MCTL PCB (14) - on neoROSA side.
079 Communication error between neoROSA and MCTL PCB (15) - on neoROSA side.
080 Communication error between neoROSA and MCTL PCB (16) - on neoROSA side.
081 Communication error between neoROSA and MCTL PCB (17) - on neoROSA side.
082 Communication error between neoROSA and MCTL PCB (18) - on neoROSA side.
083 Communication error between neoROSA and MCTL PCB (19) - on neoROSA side.
084 Communication error between neoROSA and MCTL PCB (20) - on neoROSA side.
098 Machine serial number information does not match between the backup data and EEPROM.
119 Defective image PCB (memory check error on the image processing IC).
121 Scanner adjustment error (IFLG does not change within set time).
122 Scanner adjustment error (IMFLGdoes not change within set time).
245 Timeout error on master transfer during master-making (related to Write pulse motor).
921 USB controller chip does not reply. May need to replace neoROSA.
934 Communication error between MCTL PCB and RF PCB. (on RF PCB side) 935 Communication error between MCTL PCB and RF PCB. (on MCTL PCB side) 937 Serial number not set.
938 EEPROM version down.
947 24V-A does not go ON. (possibility of 24v fuse broken on A-series) 948 24V-B does not go ON. (possibility of 24v fuse broken on B-series) 949 42V-A does not go OFF.
950 42V-B does not go OFF.
952 Check-sum error on neoROSA PCB flash memory.
953 Write error on the neoROSA PCB flash memory.
960 Read error on the neoROSA PCB flash memory.
961 Flash memory on neoROSA PCB not used.
Error Type P99 [Software error]
Description
P99-xxx Software error Press Reset Key
If Recovery has Failed, Call Service To reset
display Pull out the print cylinder and set it back.
Error Point Error Conditions
509 Master-loading sensor was OFF when the master was checked at a specified drum angle during the master-loading operation.
[ 15-12 ] 15-12 ] KZ30 (Rev. 1.2)
Imagetec Solutions Australia
Error Type A01 [Master feed error]
Description
A01-xxx
Master Mis-Feed
Pull Out Master Making Unit and Rewind Master Roll, then Reset Master in Place.
To reset display
Open the master-making unit and rewind the master material on the master roll, and then reset the master, or turn OFF the power and power back ON.
Error Point Error Conditions
201 Master-positioning sensor does not go ON even after the write pulse motor is activated during the master-positioning, master-cut, or master-loading operation.
258 Master end tape detected twice in a row.
Error Type A02 [Master loading error]
Description
A02-xxx
Master Loading Error
Pull Out Print Cylinder and Discard Master.
To reset
display Pull out the print cylinder and set it back.
Error Point Error Conditions
509 Master-loading sensor was OFF when the master was checked at a specified drum angle during the master-loading operation.
Error Type A04 [Master disposal error]
Description
A04-xxx
Master Disposal Error
Pull Out Print Cylinder and Discard Master.
To reset
display Pull out the print drum and push it back in.
Error Point Error Conditions
303 Check Print Drum - Master removal error / Master disposal jam.
Error Type A05 [Master present in the master disposal area]
Description
A05-xxx
Master Jammed in Disposal Unit