Site Requirements 17

NOTE: This site will require that the user disable (tur n off) the pop-up blocker in their browser settings. To do

so, step through the following quick flow, then resume the Installation procedure.

a) With the browser window open, click on the Tools option from the standard toolbar, then select the Pop-up Blocker option.

b) Click on the Pop-up Blocker menu option.

c) Click on the Pop-up Blocker Settings sub-menu option

d) Enter our web address in the screen’ s Address of w ebsite to allow field, then click on the <Add> button.

FIGURE 30 GINNIENETMAIN MENU SCREEN (W/MAINTENANCE LINK)

[Step 3] Returning to the GinnieNET Main Menu screen, click on the screen’s Maintenance link.

[Step 4] Click on the Download Fingerprint Softw are link. A Security Warning m essage screen will then display, like that shown here in FIGURE 31.

FIGURE 31 SECURITY WARNING SCREEN (W/<RUN>BUTTON)

[Step 5] Click on the <Run> button to install the fingerprint scanning software. The system will then display an installation “progress bar” (FIGURE 32) to indicate the status of the current software installation.

FIGURE 32 INSTALLATION STATUS BAR SCREEN

[Step 6] Once this initial download sequen ce is completed, click on the <Open> button to begin the actual fingerprint scanning software installation. A Run Software? Security Warning screen will display, like that shown here in FIGURE 33.

FIGURE 33 RUN SOFTWARE?SECURITY WARNING SCREEN

[Step 7] Then, click on the <Run> button to run the M2SYS BioPlugIn Client 6.6.2.2 software.The

M2SYS BioPlugIn Client 6.6.2.2 InstallShield Wizard screen—shown on the following

FIGURE 34 M2SYSBIOPLUGIN CLIENT 6.6.2.2INSTALLSHIELD WIZARD SCREEN

[Step 8] Click on the <Next> button to begin the program installation. The M2SYS BioPlugIn Client Welcome screen will then display.

[Step 9] Once initialized, the Setup Wizard will display the program Welcome screen. Click on the <Next> button to acknowledge the welcome, after reviewing both the posted security warning and copyright information.

FIGURE 35 INSTALLSHIELD WIZARD WELCOME SCREEN

[Step 10] On the new M2SYS BioPlugIn Client InstallShield Wizard Welcome screen, click on the <Next> button once again to proceed to the next screen level. A License Agreement

screen will then display, like that shown here in FIGURE 36.

[Step 11] Carefully read the License Agreem ent’s ELECTRONIC LICENSE AND WARRANTY

AGREEMENT section. The user may also click on the screen’s <Print> button to route the License Agreement to print should y ou wish to obtain a printed copy of that License Agreement.

[Step 12] Enable the I accept the terms in the license agreement radial button ( ), to signify your review and agreement with all terms specified therein.

[Step 13] Click on the <Next> button once again to proceed to the next screen level. The Customer

Information screen will then display, like that shown below in FIGURE 37.

FIGURE 37 INSTALLSHIELD WIZARD CUSTOMER INFORMATION SCREEN

[Step 14] Enter a specific user nam e in the User Name: field, and organization nam e in the screen’s

Organization: field, then click on the <Next> button. The Destination Folder screen will

FIGURE 38 INSTALLSHIELD WIZARD DESTINATION FOLDER SCREEN

[Step 15] The Setup Wizard will recom mend a default installation. If y ou need to change to a

different folder, or to create a new folder, click on the <Change…> button. Click on the <Next> button if the current destination folder location is acceptable, and to move on to the next screen level.

The Program Folder (or group) is the window in which the Bio-Plugin program will be located. The program folder nam e, which appears in the Program Folders field above, will be set as the default. To m odify the selection, simply click on either the <Back> button or <Install> button to accept the entries, and to start copying files

The Ready to Install the Program screen will then display, like that shown on the following page in FIGURE 39.

[Step 16] On the new Ready to Install the Program screen, the program folder will display the location in which the Bio-Plugin program can be found. The program folder name, which appears in the Program Folders field above, will be set as the default. To change any of the current settings, simply click on the <Back> button to return to any of the previous screen series to effect that setting change, or click on the <Install> button to ACCEPT all settings, and to begin the file downloading process.

FIGURE 39 INSTALLSHIELD WIZARD READY TO INSTALL THE PROGRAM SCREEN

[Step 17] The system will again display an installation “progress bar” (FIGURE 40 above) to indicate the status of the current software installation. Be advised that the system may take several minutes to copy all program files.

FIGURE 41 INSTALLSHIELD WIZARD COMPLETED SCREEN

[Step 18] Click on the screen’s <Finish> button to complete the software download task.

[Step 19] The system will then configure the fingerprint software, and display a “Please wait…” screen message (FIGURE 42). Do not click on the <Cancel> button, but instead allow the

configuration action to complete.

FIGURE 43 CONNECT FINGERPRINT SCANNER SCREEN

[Step 20] Once the user has received the “Driver inst allation completed successfully” message screen (FIGURE 43), they should sim ply click on the <OK> button to com plete the full program installation.

NOTE: Be advised that by clicking on the <OK> button above will also serve to restart the user’s computer.

[Step 21] Once the user logs back into the system, they m ay now phy sically attach the Fingerprint Scanner hardware to any of their PC-based USB port connection points. The sy stem will then automatically prompt the user for entr y of their License ID number (LID#), which can be quickly located by looking on the underside of the scanner unit itself.

[Step 22] Once the Biometrics: License ID screen displays, click on the screen’s <Yes> button to restart the computer and to complete the installation.

[Step 23] Once y ou log back into y our sy stem, attach the Fingerprint Scanner to and of the unit’s USB ports. The system will prompt you for entry of the valid License ID (LID#) which can always be found on the rear panel of the scanner unit.

FIGURE 45 BIOMETRICS:LICENSE ID(LID) ENTRY SCREEN