In addition to the system constitution data for IPT (P2P CCIS), do the following programming
1ST DATA MEANING 2ND DATA MEANING 00000 IP Address Pattern No
assigned by CM8A + IP Address No. 00
10010015150 IP Address of opposite 2400 IPX
00001 IP Address Pattern No.
assigned by CM8A + IP Address No. 01
10010015151 IP Address of opposite 2400 IPX
3-59 NWA-033621-001 Rev.2.0 90ch3001.fm
IPT (P2P CCIS) DATA ASSIGNMENT
DESCRIPTION DATA
Specify the maximum number of digits dialed by the calling party.
The maximum number of digits (including the area codes) should be assigned to each area code.
•
(1) (2)
Y=0-7 Area Code Development Pattern No. 0-7 assigned by CM8A Y=A000
X: 1st digit of remote office station No.
01-24 : 1-24 digits 25-79 : 25-79 digits Assign the port number of the TCP server to
the system.
01024-65534: TCP Server Port No. 1024-65534 00000-01023: 57000
NONE : 57000
CCC : Clear
Assign the TCP Client base port number to the system.
NOTE: 1024 ports from the base port num-ber you set are assigned as TCP Client port number.
• (1) (2)
Y=1XX (VOIP Port [1] + Unit No. [01-50]) 35
064512: TCP Client Port No. 1024-64512
00000-01023: Controlled with 58000 64513-65534: Controlled with 58000 NONE : 58000-59023
CCC : Clear
Provide the Link Reconnect for IP network. (1) (2)
606
0 : Not provided 1 : To provide Provide the Link Reconnect for IPT (P2P
CCIS).
NOTE: This command is effective when CM08>606 is set to 1.
(1)
IPT (P2P CCIS) RESET
IPT (P2P CCIS) RESET
CM08
END
IPT (P2P CCIS) DATA ASSIGNMENT
• To provide the Alternative Routing (another trunk route) for the IPT (P2P CCIS) when an outgoing call via the IPT (P2P CCIS) is not available due to the LAN cable of VoIPDB is pulled out or a fault occurrence, in addition to “IPT (P2P CCIS) Data Assignment” do the following programming.
DESCRIPTION DATA
Provide the system with the check of the LAN cable of VoIPDB is pulled out.
(1) (2)
723
0 : To provide 1 : Not provided Provide the voice channel route of IPT (P2P
CCIS) with Alternative Routing for a fault occurrence.
• (1) (2)
Y=186
00-63: Trunk Route No.
0 : To provide 1 : Not provided When the outgoing trunk of the tandem office
is IPT (P2P CCIS), provide the incoming trunk route with Alternative Routing for a tandem call.
• (1) (2)
Y=192
00-63: Trunk Route No.
0 : To provide 1 : Not provided Provide the system with Alternative Routing
of CCIS outgoing call when all outgoing trunks of tandem office are busy.
(1) (2)
372
0 : To provide 1 : Not provided Set the ORT timer when established tandem
connection to CCIS.
• (1) (2)
Y=0 104
02-99: 2-99 seconds
(1 second increments)
If no data is set, the default setting is 7 seconds.
Assign a Numbering Plan Group to each ten-ant.
(1) (2)
00-63: Tenant No.
710-713 : Numbering Plan Group 0-3 NONE : Numbering Plan Group 0 Assign the access code for LCR Group 0-3. •
(1) (2)
Y=0-3 Numbering Plan Group 0-3 X-XXXX: Access Code
A126: LCR Group 0 A127: LCR Group 1 A128: LCR Group 2 A129: LCR Group 3 START
3-61 NWA-033621-001 Rev.2.0 90ch3001.fm
IPT (P2P CCIS) DATA ASSIGNMENT
DESCRIPTION DATA
Assign a service access key for LCR Group 0-2 to Multiline Terminal, if required.
• (1) (2)
Y=00
My Line No. + + Key No.
F0A26-F0A28: LCR Group 0-2 Assign the Area Code Development Pattern
number for maximum digit analysis to each trunk route.
• (1) (2)
Y=076
00-63: Trunk Route No.
05-07: Area Code Development Pattern No. 5-7
Assign an Area Code Development Pattern number to each LCR Group.
• (1) (2)
Y=A000
0-3: LCR Group 0-3
4005-4007: Area Code Development Pat-tern No. 5-7
Assign a Route Pattern number to each area code for the Area Code Development Pattern number assigned by CM8A Y=A000.
• (1) (2)
Y=4005-4007 Area Code Development Pattern No. 5-7
X...X: Area Code, Maximum 8 digits 0000-0255: Route Pattern No. 000-255 Assign a LCR Pattern number to each area
code for the Area Code Development Pattern number assigned by CM8A Y=A000.
• (1) (2)
Y=4005-4007 Area Code Development Pattern No. 5-7
X...X: Area Code, Maximum 8 digits 0000-0255: LCR Pattern No. 000-255 For area code deletion, designate the digits to
be not deleted.
• (1) (2)
Y=5000-5255 LCR Pattern No. 000-255 152: Deletion of all digits of the area code
assigned by CM8A Y=4005-4007 1 : Not deleted
Assign the next Route Pattern number to the Route Pattern number assigned by CM8A Y=4005-4007.
NOTE: This data is required to expand the order of LCR selection that is as-signed by CM8A Y=0000-0255.
The order of LCR selection can be expand to the maximum seventh.
• (1) (2)
Y=0000-0255 Route Pattern No. 000-255 0: Designation of next table
00255: Next Route Pattern No. 000-255
IPT (P2P CCIS) DATA ASSIGNMENT
DESCRIPTION DATA
Specify the order of LCR selection for the Route Pattern number assigned by CM8A Y=4005-4007.
• (1)
(2)
Y=0000-0255 Route Pattern No. 000-255 1-4: Order of LCR Selection
1: 1st 2: 2nd 3: 3rd 4: 4th XXX ZZ
XXX: 000-255: LCR Pattern No.
ZZ : 00-63: Trunk Route No.
NOTE: You cannot assign CM8A Y=0000-0255 1st data 0 (Destination of next table) and 1st data 4 (4th LCR selection) simultaneously. The latest data assignment including system data memory clear is effective. The other assigned data is set as NONE.
Example:
Specify the maximum number of digits to be dialed by calling party.
The maximum number of digits including the area codes should be assigned to each area code.
•
(1) (2)
Y=5-7 Area Code Development Pattern No. 5-7 assigned by CM8A Y=A000
X-X...X: Area code dialed, Maximum 8 digits
01-24 : 1 digit-24 digits 25-79 : 25 digits-79 digits Assign an ACM signal waiting timer after • Y=10
B
CM8A
Y 1ST DATA 2ND DATA ORDER OF LCR
SELECTION 0000 0 Destination of next table 0001
1 1st LCR selection 00000 1st LCR selection
2 2nd LCR selection 00101 2nd LCR selection
3 3rd LCR selection 00202 3rd LCR selection
4 4th LCR selection NONE (Unavailable) 0001 0 Destination of next table NONE
1 1st LCR selection 00303 4th LCR selection
2 2nd LCR selection 00404 5th LCR selection
3 3rd LCR selection 00505 6th LCR selection
4 4th LCR selection 00606 7th LCR selection
CM85
CMA7
3-63 NWA-033621-001 Rev.2.0 90ch3001.fm
IPT (P2P CCIS) DATA ASSIGNMENT