8 Human Machine Interface
8.2 Menu Tree
8.2.3 Sub Menus
8.2.3.1 Measurements
Main Menu
Measurements2 Measurements1 Measurements
Measurements3
This menu is used to display real-time measured values, including AC voltage, AC current, phase angle and calculated quantities. These data can help users to acquaint the device’s status. This menu comprises following submenus. Please refer to Section “Measurement” about the detailed measured values.
No. Item Function description
1 Measurement1 Display measured values from protection calculation DSP (Displayed in
secondary value)
2 Measurement2 Display measured values from fault detector DSP (Displayed in secondary value)
3 Measurement3 Display measured primary values and other calculated quantities 8.2.3.2 Status
Main Menu
Contact Inputs Inputs
Status
Outputs
GOOSE Inputs
Superv State
Prot Superv Contact Outputs
FD Superv
GOOSE Superv
SV Superv GOOSE Outputs
Interlock Status
This menu is used to display real time input signals, output signals and alarm signals of the device.
These data can help users to acquaint the device′s status. This menu comprises following submenus. Please refer to Section “Signal List” about the detailed input and output signals, and Section “Supervision Alarms” about alarm signals.
No. Item Function description
1 Inputs Display all input signal states
2 Outputs Display all output signal states
3 Superv State Display supervision alarm states The submenu “Inputs” comprises the following command menus.
No. Item Function description
1 Contact Inputs Display states of binary inputs derived from opto-isolated channels 2 GOOSE Inputs Display states of GOOSE binary inputs.
The submenu “Outputs” comprises the following command menus.
No. Item Function description
1 Contact Outputs Display states of contact binary outputs 2 GOOSE Outputs Display states of GOOSE binary outputs
3 Interlock Status Display states of interlock result of each remote control.
The submenu “Superv State” comprises the following command menus.
No. Item Function description
1 Prot Superv Display states of self-supervision signals from protection calculation DSP 2 FD Superv Display states of self-supervision signals from fault detector DSP 3 GOOSE Superv Display states of GOOSE self-supervision signals
4 SV Superv Display states of SV self-supervision signals 8.2.3.3 Records
Main Menu
Device Logs Superv Events Disturb Records
IO Events Records
Clear_Records
This menu is used to display all kinds of records, including the disturbance records, supervision events, binary events and device logs, so that the operator can load to view and use as the reference of analyzing accidents and repairing the device. All records are stored in non-volatile memory, it can still record them even if it loses its power.
This menu comprises the following submenus.
No. Item Function description
1 Disturb Records Display disturbance records of the device 2 Superv Events Display supervision events of the device 3 IO Events Display binary events of the device 4 Device Logs Display device logs of the device 5 Control Logs Display control logs of the device
6 Clear Records Clear all records.
8.2.3.4 Settings
Main Menu
GOOSE Links Function Links Settings
System Settings
SV Links Prot Settings
Logic Links
Device Setup
Comm Settings Device Settings
Label Settings Spare Links AuxE Settings FD Settings
OC Settings ROC Settings
DeadZone Settings BFP Settings
PD Settings VTS/CTS Settings
AR/Syn Settings Trip Logic Settings
Copy Settings
DPos Settings Syn Settings
Control Settings Mon/Ctrl Settings
Interlock Settings
This menu is used to check the device setup, system parameters, protection settings and logic links settings, as well as modifying any of the above setting items. Moreover, it can also execute the setting copy between different setting groups.
This menu comprises the following submenus.
No. Item Function description
1 System Settings Check or modify the system parameters 2 Prot Settings Check or modify the protection settings
3 Mon/Ctrl Settings Check or modify the measurement and control settings
4 Logic Links Check or modify the logic links settings, including function links, SV links, GOOSE links and spare links
5 Device Setup Check or modify the device setup
The submenu “Prot Settings” includes the following command menus.
No. Item Function description
1 FD Settings Check or modify fault detector settings 2 AuxE Settings Check or modify auxiliary element settings
3 OC Settings Check or modify phase overcurrent protection settings 4 ROC Settings Check or modify residual overcurrent protection settings 5 BFP Settings Check or modify breaker failure protection settings 6 DeadZone Settings Check or modify dead zone protection settings 7 PD Settings Check or modify pole discrepancy protection settings
8 VTS/CTS Settings Check or modify VT circuit supervision and CT circuit supervision settings
9 Trip Logic Settings Check or modify trip logic settings
10 AR/Syn Settings Check or modify auto-reclosing and synchronism check settings 11 Copy Settings Copy setting between different setting groups
The submenu “Mon/Ctrl Settings” includes the following command menus.
No. Item Function description
1 Syn Settings Check or modify manual sysnchronism check settings 2 DPos Settings Check or modify double point binary input settings 3 Control Settings Check or modify control settings
4 Interlock Settings Check or modify interlock settings
The submenu “Logic Links” comprises the following command menus.
No. Item Function description
1 Function Links Check or modify function links settings
2 GOOSE Links Check or modify GOOSE links settings
3 SV Links Check or modify SV links settings
4 Spare Links Check or modify spare links settings (used for programmable logic) The submenu “Device Setup” comprises the following command menus.
No. Item Function description
1 Device Settings Check or modify the device settings.
2 Comm Settings Check or modify the communication settings.
3 Label Settings Check or modify the label settings of each protection element.
8.2.3.5 Print
Main Menu
Settings Device Info Print
Device Setup
All Settings
Disturb Records
Superv Events
IO Events
Device Status
Waveform
IEC103 Info
Cancel Print
System Settings
Prot Settings
Mon/Ctrl Settings
Logic Links
Latest Chgd Settings
This menu is used to print device description, settings, all kinds of records, waveform, information related with IEC60870-5-103 protocol, channel state and channel statistic.
This menu comprises the following submenus.
No. Item Function description
1 Device Info Print the description information of the device, including software version.
2 Settings
Print device setup, system parameters, protection settings and logic links settings. It can print by different classifications as well as printing all settings of the device. Besides, it can also print the latest modified settings.
3 Disturb Records Print the disturbance records 4 Superv Events Print the supervision events
5 IO Events Print the binary events
6 Device Status Print the current state of the device, including the sampled value of voltage and current, the state of binary inputs, setting and so on
7 Waveform Print the recorded waveform
8 IEC103 Info
Print 103 Protocol information, including function type (FUN), information serial number (INF), general classification service group number, and channel number (ACC)
9 Cancel Print Cancel the print command
The submenu “Settings” comprises the following submenus.
No. Item Function description
1 System Settings Print the system parameters 2 Prot Settings Print the protection settings
3 Mon/Ctrl Settings Print the measurement and control settings 4 Logic Links Print the logic links settings
5 Device Setup Print the settings related to device setup
6 All Settings Print all settings including device setup, system parameters, protection settings and logic links settings
7 Latest Chgd Settings Print the setting latest modified
The submenu “Prot Settings” comprises the following command menus.
No. Item Function description
1 FD Settings Print fault detector element settings 2 AuxE Settings Print auxiliary element settings
3 OC Settings Print phase overcurrent protection settings 4 ROC Settings Print directional earth-fault protection settings 5 BFP Settings Print breaker failure protection settings 6 Deadzone Settings Print dead zone settings
7 PD Settings Print pole discrepancy protection settings
8 VTS/CTS Settings Print VT circuit supervision and CT circuit supervision settings 9 Trip Logic Settings Print trippling logic settings
10 AR/Syn Settings Print synchronism check and auto-reclosing settings 11 All Settings Print all settings included in “Prot Settings” submenu The submenu “Mon/Ctrl Settings” includes the following command menus.
No. Item Function description
1 Syn Settings Print manual sysnchronism check settings 2 DPos Settings Print double point binary input settings 3 Control Settings Print control settings
4 Interlock Settings Print interlock settings
5 All Settings Print all settings included in “Mon/Ctrl Settings” submenu The submenu “Logic Links” comprises the following command menus.
No. Item Function description
1 Function Links Print function links settings
2 GOOSE Links Print GOOSE links settings
3 SV Links Print SV links settings
4 Spare Links Print spare links settings (used for programmable logic) 5 All Settings Print all settings included in “Logic Links” submenu The submenu “Device Setup” comprises the following command menus.
No. Item Function description
1 Device Settings Print the device settings.
2 Comm Settings Print the communication settings.
3 Label Settings Print the label settings of each protection element.
4 All Settings Print all settings included in “Device Setup” submenu
8.2.3.6 Local Cmd
Main Menu
Local Cmd
Reset Target
Trig Oscillograph
Download
Clear Counter Control
Clear Energy Counter Clear AR Counter
This menu is used to reset the tripping relay with latch, indicator LED, LCD display, and as same as the resetting function of binary inputs. This menu provides a method of manually recording the current waveform data of the device under normal condition for printing and uploading SAS.
Besides, it can send out the request of program download, clear statistic information about GOOSE SV AR and energy.
This menu comprises the following submenus.
No. Item Function description
1 Reset Target Reset the local signal, indicator LED, LCD display and so on 2 Trig Oscillograph Trigger waveform recording
3 Control Manually operating to trip, close output or for signaling purpose
4 Download Send out the request of downloading program
5 Clear Counter Clear GOOSE and SV statistic data 6 Clear AR Counter Clear AR statistic data
7 Clear Energy Counter Clear all energy metering values (i.e. PHr+_Pri, PHr-_Pri, Qr+_Pri, QHr-_Pri)
8.2.3.7 Information
Main Menu
Information
Version Info
Board Info
In this menu, the LCD displays software information of all kinds of intelligent plug-in modules,
which consists of version, creating time of software, CRC codes and management sequence number. Besides, plug-in module information can also be viewed.
This menu comprises the following command menus.
No. Item Function description
1 Version Info
Display software information of DSP module, MON module and HMI module, which consists of version, creating time of software, CRC codes and management sequence number.
2 Board Info Monitor the current working state of each intelligent module.
8.2.3.8 Test
Main Menu
Test
Device Test
GOOSE Comm Counter
SV Comm Counter
Disturb Events
Superv Events
IO Events AR Counter
This menu is mainly used for developers to debug the program and for engineers to maintain the protection device. It can be used to fulfill the communication test function. It is also used to generate all kinds of reports or events to transmit to the SAS without any external input, so as to debug the communication on site. Besides, it can also display statistic information about GOOSE SV and AR.
This menu comprises the following submenus.
No. Item Function description
1 GOOSE Counter Check communication statistics data of GOOSE
2 SV Counter Check communication statistics data of SV (Sampled Values)
3 AR Counter Check AR counters
4 Device Test
Automatically generate all kinds of reports or events to transmit to SCADA, including disturbance records, self-supervision events and binary events. It can realize the report uploading by different classification, as well as the uploading of all kinds of reports
The submenu “Device Test” comprises the following submenus.
No. Item Function description
1 Disturb Events View the relevant information about disturbance records (only used for debugging persons)
2 Superv Events View the relevant information about supervision events (only used for debugging persons)
3 IO Events View the relevant information about binary events (only used for debugging persons)
Users can respectively execute the test automatically or manually by selecting commands “All Test” or “Select Test”.
The submenu “Disturb Events” comprises the following command menus.
No. Item Description
1 All Test Ordinal test of all protection elements 2 Select Test Selective test of corresponding classification
The submenu “Superv Events” comprises the following command menus.
No. Item Description
1 All Test Ordinal test of all self-supervisions
2 Select Test Selective test of corresponding classification The submenu “IO Events” comprises the following command menus.
No. Item Description
1 All Test Ordinal test of change of all binary inputs 2 Select Test Selective test of corresponding classification 8.2.3.9 Clock
The current time of internal clock can be viewed here. The time is displayed in the form YY-MM-DD and hh:mm:ss. All values are presented with digits and can be modified.
8.2.3.10 Language
This menu is mainly used to set LCD display language.