6 NPT-1200 Specifications
6.7 Throughput Test - RFC2544
Number of RFC2544 test port 2
Max test rate 1000 Mbps (NPT-1200 with
CPTS100/CPS100/CPTS320/CPS320)
Test rate granularity 64Kbps~960Kbps@64Kbps,
1Mbps~Max rate@100Kbps
Transmit frame size Fixed (64~1522B)
IMIX
44 Depends on the network conditions and PTP protocol configuration, and limited by 2000 pps budget.
IMIX types Standard IMIX G.8261 IMIX1 G.8261 IMIX2 User defined IMIX
Performance test Frame loss (Latency and jitter test is
not supported)
6.8 Acoustic Noise
Acoustic noise 62 dBA
6.9 Jitter and Wander
Applicable specifications ITU T G.823, G.825
6.10 I/O Interfaces
This section describes the specifications for the I/O interfaces.
6.10.1 2.048 Mbps (E1)
Physical level G.703, Paragraph 6/s ±50ppm Frame options Unframed, framed (ITU-T G.704)
Line code HDB3
Line impedance 120 Ω balanced ± 5%
6.10.2 1.544 Mbps (T1)
Physical level ANSI T1.403-1999
Frame options Unframed, framed (ANSI T1.107-2002 [R2006]) Line code AMI/B8ZS
Line impedance 100 Ω balanced
6.10.3 STM-1 Electrical
Physical level G.703, Paragraph 12 Bitrate 155.52 Mbps ± 20 ppm
Frame G.707
Line code CMI
6.10.4 STM-1/OC-3 Optical
Physical level G.957, Table 2
Wavelength 1310 nm, 1550 nm
Bitrate 155.52 Mbps ± 4.6 ppm
Transmission range S3, L3, L5, X3, X5, VL5
6.10.5 STM-4 Optical
Physical level G.957, Table 3 Wavelength 1310 nm, 1550 nm
Bitrate 622 Mbps ± 4.6 ppm
Transmission range S3, L3, L5, V5
6.11 Management
Applicable specifications G.784, G.774, M.3010, M.3100 LightSoft (ECI Telecom Network
Manager) server and client for managing all ECI Telecom equipment
on SUN workstation(s)
EMS-APT (element manager) on PC or SUN workstation(s) LCT-APT (local craft terminal) on PC
6.11.1 Management and Alarm Interfaces
CMIP-like over TCP/IP to EMS-APT
SNMP V3 to third-party SNMP-based management solution (monitoring only) MTNM from EMS-APT to LightSoft or other TMN
10/100BaseT to LCT-APT Rack Alarm Panel
6.11.2 Alarms and Performance
Performance concept ITU-T G.821, G.826, Bellcore GR-820-CORE Alarm concept G.783
Alarm types LED indicators, dry contacts,
(per subrack), external alarm inputs and outputs Alarm classes Critical, Major, Minor, Warning
6.11.3 Management Communication Channel
MCC Interfaces Management LAN interface for DCN
RS-DCC, MS-DCC, E1 clear channel for SDH network In-band MCC for Ethernet/MPLS network
GCC for OTN network IP & Routing protocol IPv4
OSPFv2 IP Route table capacity 8000
Interface types Numbered, unnumbered
Link Layer Encapsulation IEEE 802.3 Ethernet – For management port or in-band MCC LAN emulation over HDLC – For DCC
PPP over HDLC – For DCC or GCC IEEE 802.1q – For in-band MCC IEEE 802.1ad – For in-band MCC DCC processing capacity 10 Mbps
Maximum number of DCC channels 32 x RS-DCC (192 Kbps), 32 x MS-DCC (576 Kbps) Max number of LAN emulation
interfaces for DCC 4
Max number of PPP interfaces for DCC
and GCC 32
In-band MCC processing capacity 10 Mbps Number of management VLAN per NE 8 Number of management VLAN per PE 1 Maximum number of MCC channels 32
MCC bandwidth per interface 256 Kbps~4 Mbps@ 256Kbps
Maximum number of GCC channels 6 (only MXP10 OTU2/OTU2e ports support GCC) GCC termination type GCC0, GCC1, GCC2
Clear channels 2 x E1 clear channel
Framed or unframed
6.12 SDH Interfaces
This section describes the specifications for the SDH interfaces.
6.12.1 STM-1 (155.52 Mbps ± 4.6 ppm)
Table 6-3: STM-1 interface
SFP transceiver name OTR1_S3 OTR1_L3 OTR1_L5 OTR1_X3 OTR1_X5 OTR1_VL5 OTR1_VLC5 Application code45 S-1.1 L-1.1 L-1.2
Operating wavelength (nm) 1261-1360 1263-1360 1480-1580 1270-1360 1500-1520 1500-1520 1544.5-1557.5 TRANSMITTER
Source type MLM SLM SLM SLM SLM SLM SLM
Max. RMS width (nm) 7.7 - - - - - -
Min. side mode suppression
ratio (dB) - 30 30 30 > 30 > 30 30
Min. mean launched power
(dBm) -15 -5 -5 +5 0 0 0
Max. mean launched power
(dBm) -8 0 0 0 +5 +5 5
OPTICAL PATH BETWEEN S &
R
Max. dispersion (ps/nm) 96 - - - - - -
Min. optical return loss of
cable (dB) - - -20 - -20 - -
Max. discrete reflectance (dB - - -25 - -25 -25 -
Max. optical path penalty
(dB) 1 1 1 1 1 1 2
N
OTE: When selecting bidirectional transceivers, pay attention that they must operate in complementary pairs. For example: OTR1-S3BD can work only vis-a-vis OTR1-S5BD;OTR4-L3BD can work only vis-a-vis OTR4-L5BD, and so on. The transceivers in the following table are arranged in complementary pairs.
45 Application code is in reference to ITU-T Recommendation G.691.
46 Receiver units of SFPs (excluding bidirectional SFPs) are a wide-band type.
Table 6-4: STM-1 bidirectional transceivers
SFP transceiver name OTR1-S3BD OTR1-S5BD OTR1-L3BD OTR1-L5BD OTR1-X49BD OTR1-X59BD
Application code47 BD 348 BD 549 L3BD L5BD X49BD X59BD
Operating wavelength (nm) 1260-1360 1480-1580 1280-1360 1480-1580 1460-1500 1580-1620 TRANSMITTER
Source type MLM MLM MLM SLM SLM SLM
Max. RMS width (nm) 7 3 4 1 1 1
Min. side mode suppression ratio
(dB) - - - 30 30 30
Min. mean launched power (dBm) -14 -14 -5 -5 -5 -5
Max. mean launched power (dBm) -8 -8 0 0 0 0
Min. extinction ratio (dB) 10 10 10 10 10 10
RECEIVER50
Min. sensitivity (BER of 1 * 10-12)
EOL (dBm) -32 -32 -32 -32 -34 -34
Min. overload (dBm) -8 -8 0 0 0 0
Max. receiver reflectance (dB) - - - - - -
OPTICAL PATH BETWEEN S & R
Max. dispersion (ps/nm) - - - - - -
Min. optical return loss of cable (dB) -20 -20 - - - -
Max. discrete reflectance (dB) - - - - - -
Max. optical path penalty (dB) 1 1 1 1 1 1
6.12.2 STM-4 (622 Mbps ± 4.6 ppm)
Table 6-5: STM-4 transceivers
SFP transceiver name OTR4_S3 OTR4_L3 OTR4_L5 OTR4_V5 OTR4_LC5
Application code51 S 4.1 L 4.1 L 4.2 V5 LC5
Operating wavelength (nm) 1293-1334
1274-1356
1296-1330 1300-1325
1480-1580 1550 1551
47 Application code is in reference to ITU-T Recommendation G.691.
48 BD 3: STM-1 single-fiber bidirectional SFP module with a 1310 nm TX wavelength.
49 BD 5: STM-1 single-fiber bidirectional SFP module with a 1550 nm TX wavelength.
50 Receiver units of SFPs (excluding bidirectional SFPs) are a wide-band type.
51 Application code is in reference to ITU-T Recommendation G.691.
SFP transceiver name OTR4_S3 OTR4_L3 OTR4_L5 OTR4_V5 OTR4_LC5
Application code51 S 4.1 L 4.1 L 4.2 V5 LC5
TRANSMITTER
Source type MLM MLM SLM SLM CWDM
Max. RMS width (nm) 4/2.5 - - - -
Max. -20 dB width (nm) - 1 <1 1 1
Min. side mode suppression ratio (dB) - 30 30 30 30
Min. mean launched power (dBm) -15 -3 -3 0 -1
Max. mean launched power (dBm) -8 +2 +2 4 5
Min. extinction ratio (dB) 8.2 10 10 10 10
RECEIVER52
Min. sensitivity (BER of 1 * 10-12) EOL (dBm) -28 -28 -28 -34 -29
Min. overload (dBm) -8 -8 -8 -8 0
Max. receiver reflectance (dB) - -14 -27 -27 -27
OPTICAL PATH BETWEEN S & R
Max. dispersion (ps/nm) 46/74 92/109 1600 2400 1600
Min. optical return loss of cable (dB) - 20 24 - -
Max. discrete reflectance (dB) - -25 -27 - -
Max. optical path penalty (dB) 1 1 1 1 2
N
OTE: When selecting bidirectional transceivers, pay attention that they must operate in complementary pairs. For example: OTR4-S3BD can work only vis-a-vis OTR4-S5BD;OTR4-L3BD can work only vis-a-vis OTR4-L5BD, and so on. The transceivers in the following table are arranged in complementary pairs.
N
OTE: OTR16 bidirectional SFPs (in the following table) are multirate transceivers that support both STM-4 and STM-16.
52 Receiver units of SFPs (excluding bidirectional SFPs) are a wide-band type.
Table 6-6: STM-4 bidirectional transceivers
SFP transceiver name OTR4_S3BD OTR4_S5BD OTR4_L3BD OTR4_L5BD OTR16_X49B
D OTR16_X59B
D
Application code53 S3BD S5BD L3BD L5BD X49BD X59BD
Operating wavelength (nm) 1260-1360 1480-1580 1260-1360 1480-1580 1460-1500 1560-1620 TRANSMITTER
Source type MLM SLM MLM SLM SLM SLM
Max. RMS width (nm) 3 1 3 1 1 1
Min. side mode suppression
ratio (dB) - 30 - 30 30 30
Min. mean launched power
(dBm) -15 -15 -3 -3 -2 -2
Max. mean launched power
(dBm) -8 -8 +2 +2 +3 +3
Min. extinction ratio (dB) 8.2 8.2 10 10 8.2 8.2
RECEIVER54
Min. sensitivity (BER of 1 *
10-12) EOL (dBm) -28 -28 -28 -28 -28 -28
Min. overload (dBm) -8 -8 -8 -8 -6 -6
Max. receiver reflectance (dB) - - - - -27 -27
OPTICAL PATH BETWEEN S & R
Max. dispersion (ps/nm) - - - - -
Min. optical return loss of cable
(dB) - - - - - -
Max. discrete reflectance (dB) - - - - - -
Max. optical path penalty (dB) 1 1 1 1 1 1
53 Application code is in reference to ITU-T Recommendation G.691.
54 Receiver units of SFPs (excluding bidirectional SFPs) are a wide-band type.
6.13 Ethernet Specifications
Table 6-7: Ethernet Layer 2/MPLS-TP cards
Card Max cards per platform Service interfaces CPTS/CPS Connectivity
DHXE_2 655 2 x 10 GbE 20 GbE
DHGE_8 6 8 x 100/1000BaseX (CSFP) 8 GbE
DHGE_4E 6 4 x 10/100/1000BaseT 4 GbE
DHGE_16 2 8 x 10/100/1000BaseT
+
8 x 100/1000BaseX (CSFP)
16 GbE
DHGE_24 2 24 x 100/1000BaseX (CSFP) 24 GbE
DHFE_12 3 12 x 10/100BaseT 2.5 GbE
DHFX_12 3 12 x 10/100BaseX 2.5 GbE
6.13.1 CPS100
10 GbE interface type (SFP+) 10GBase-SR, LR, ER, ZR, BD, colored 10GBase-SW, LW, EW, ZW, BD, colored
Number of 10 GbE ports 2
Supported OTN mapping 10GBase-R mapping to OTU2e 10GBase-W mapping to OTU2
Supported FEC types ITU-T G.709 FEC
EFEC (ITU-T G.975.1 I.4) EFEC (ITU-T G.975 I.7)
Number of Sync-E ports 2
Supported types of 1588v2 PTP Clock BC, OC (slave or master), and TC Number of Sync-E Tx Timing domains 2 (system and PTP clock)
Switch capacity 100G Switching, TM 72 Gbps (for IMIX) MAC address table capacity per switch 128 K
MAC address table capacity per VSI 64 K
Supported VLAN quantity 4000 * 4094, as per IEEE 802.1ad
Supported C-VLAN groups 16000
Supported MPLS P2P tunnels queues 16000 Supported Bidirectional LSPs 2048 Maximum number of LSP1:1 Linear
Protection Domains 1024
55 Four DHXE_2 cards can be assigned, but only six ports can be activated totally.
Tunnel incoming label space for pass
through 16~32767
Tunnel incoming label space for drop 32768~262143 Supported MPLS P2MP tunnels 32
Supported maximum PWs 16000
Max number of PW redundancy groups (without PW status signaling) 16 Max number of PW Redundancy with PW state signaling or PW with PW status signaling
1280
Supported maximum VSIs 4000
Supported maximum policers 4000 Supported maximum policer profiles 256
CIR/EIR granularity of policer 64Kb/s (0~2Mb/s)
1Mb/s (2Mb/s~full port rate) CIR granularity of high CoS shaper 128K~512Kbps@128Kbps
1~16Mbps@1Mbps CIR granularity for low CoS bandwidth 128K~512Kbps@128Kbps
1~16Mbps@1Mbps PIR granularity for E-LSP bandwidth limit 1~ No Rate Limit@1Mbps Maximum sites per VPLS instance 170-number of local ports Maximum number of UNI/NNI ports per
VSI 64
Maximum number of CoSs 8
MSTP/ERPS instance number 32 Supported maximum multicast groups
per rooted MP leaf VSI 1024
Max MTU size 9736 bytes
LAG support (including MC-LAG) up to 32 LAGs with up to 8 port members per LAG
LAG based hashing MAC, IPv4, and IPv6
Supported BFD intervals 3.33 msec (fast BFD), 10 msec, 100 msec, 1000 msec
Maximum number of BFD sessions 600 Maximum number of BFD sessions over
Bidirectional LSP 500
Maximum number of BFD sessions for
section Maximum number of ports
Maximum number of BFD templates 10
Supported CFM intervals 3.33 msec, 10 msec, 100 msec 1 sec,10 sec, 60 sec, 600 sec (slow) Maximum number of
3.33ms/10ms/100ms/1000ms CCM sessions
500
Maximum aggregated packet rate for
slow CCM (1 sec/10 sec/1 min/10 min) 200 pps Total number of 3.33ms BFD and CCM
sessions <=100
Total number of 10ms/100ms CCM and
10 ms/100 ms/1000 ms BFD sessions <=500 Port ACL profiles per switch 64 Maximum number of ACE per port ACL
profile 128
Standards compliance IEEE802.1p, IEEE802.1Q, IEEE802.1ad, IEEE802.1w, IEEE802.1s, IEEE802.1ag
IEEE802.3, IEEE802.3x, IEEE802.3ad, IEEE802.3ah, IEEE802.3u, IEEE802.3z, IEEE802.3ae
RFC3031, RFC3032, RFC3916, RFC3985, RFC4090
RFC5586, RFC5654, RFC5880, RFC5921, RFC6428, RFC6378, RFC6427, RFC2544 (up to 1 GbE)
ITU-T Y.1710, Y.1711, Y.1731
G.707, G.783, G.7041 (GFP), G.7042 (LCAS), G.8032 V1 MEF9, MEF10, MEF14
ITU-T G.8262, G.8264, G.8265.1, IEEE 1588v2
6.13.2 CPS320
10 GbE interface type (SFP+) 10GBase-SR, LR, ER, ZR, BD, colored 10GBase-SW, LW, EW, ZW, BD, colored
Number of 10 GbE ports 4
Supported OTN mapping 10GBase-R mapping to OTU2e
Supported FEC types ITU-T G.709 FEC
EFEC (ITU-T G.975.1 I.4) EFEC (ITU-T G.975.1 I.7)
Number of Sync-E ports 4
Supported types of 1588v2 PTP Clock BC, OC (slave or master), and TC Number of Sync-E Tx Timing domains 2 (system and PTP clock)
Switch capacity 320G Switching, TM 240 Gbps (for IMIX) MAC address table capacity per switch 128 K
MAC address table capacity per VSI 64 K
Supported VLAN quantity 4000 * 4094, as per IEEE 802.1ad
Supported C-VLAN groups 32000
Supported MPLS P2P tunnels queues 32000 Supported Bidirectional LSPs 4096 Maximum number of LSP1:1 Linear
Protection Domains 1280
Tunnel incoming label space for pass
through 16~32767
Tunnel incoming label space for drop 32768~262143 Supported MPLS P2MP tunnels 32
Supported maximum PWs 32000
Max number of PW redundancy groups (without PW status signaling) 16 Max number of PW Redundancy with PW state signaling or PW with PW status signaling
1280
Supported maximum VSIs 4000
Supported maximum policers 4000 Supported maximum policer profiles 256
CIR/EIR granularity of policer 64Kb/s (0~2Mb/s)
1Mb/s (2Mb/s~full port rate) CIR granularity of high CoS shaper 128K~512Kbps@128Kbps
1~16Mbps@1Mbps CIR granularity for low CoS bandwidth 128K~512Kbps@128Kbps
1~16Mbps@1Mbps PIR granularity for E-LSP bandwidth limit 1~ No Rate Limit@1Mbps Maximum sites per VPLS instance 170-number of local ports
Maximum number of UNI/NNI ports per
VSI 64
Maximum number of CoSs 8
MSTP/ERPS instance number 32 Supported maximum multicast groups
per rooted MP leaf VSI 1024
Max MTU size 9736 bytes
LAG support (including MAC-LAG) up to 32 LAGs with up to 8 port members per LAG
LAG based hashing MAC, IPv4, and IPv6
Supported BFD intervals 3.33 msec (fast BFD), 10 msec, 100 msec, 1000 msec Maximum number of BFD sessions 1100
Maximum number of BFD sessions over
Bidirectional LSP 1000
Maximum number of BFD sessions for
section Maximum number of ports
Maximum number of BFD templates 10
Supported CFM intervals 3.33 msec, 10 msec, 100 msec 1 sec,10 sec, 60 sec, 600 sec (slow) Maximum number of
3.33ms/10ms/100ms/1000ms CCM sessions
1000
Maximum aggregated packet rate for
slow CCM (1 sec/10 sec/1 min/10 min) 200 pps Total number of 3.33ms BFD and CCM
sessions <=100
Total number of 10ms/100ms CCM and
10 ms/100 ms/1000 ms BFD sessions <=1000 Port ACL profiles per switch 64 Maximum number of ACE per port ACL
profile 128
Standards compliance IEEE802.1p, IEEE802.1Q, IEEE802.1ad, IEEE802.1w, IEEE802.1s, IEEE802.1ag
IEEE802.3, IEEE802.3x, IEEE802.3ad, IEEE802.3ah, IEEE802.3u, IEEE802.3z, IEEE802.3ae
RFC3031, RFC3032, RFC3916, RFC3985, RFC4090
RFC5586, RFC5654, RFC5880, RFC5921, RFC6428, RFC6378, RFC6427, RFC2544 (up to 1 GbE)
ITU-T Y.1710, Y.1711, Y.1731
G.707, G.783, G.7041 (GFP), G.7042 (LCAS), G.8032 V1 MEF9, MEF10, MEF14
ITU-T G.8262, G.8264, G.8265.1, IEEE 1588v2
6.13.3 DHXE_2
Interface connector type 2 x SFP+
Supported port types 10GBase-SR, LR, ER, ZR, BD, colored 10GBase-SW, LW, EW, ZW, BD, colored Maximum number of 10GBase-R
ports 2
Maximum number of 10GBase-W
ports 2
Number of Sync-E ports 2 (all ports)
Number of Sync-E Tx clock domains 2 (System clock, PTP clock) Standards compliance IEEE802.3
ITU-T G.8262
6.13.4 DHXE_4
Interface connector type 4 x SFP+
Supported port types 10GBase-SR, LR, ER, ZR, BD, colored Maximum number of 10GBase-R
ports 4
Number of Sync-E ports 4 (all ports)
Number of Sync-E Tx clock domains 1 (System clock - T0) Standards compliance IEEE802.3
ITU-T G.8262
6.13.5 DHGE_4E
Interface connector type 4 x RJ45
Supported ports 4 x 10/100/1000Base-Tx with PoE+ support PoE PSE pin-out IEEE 802.3af, Alternative A
Supported PD type IEEE 802.3at type 1, type 2 Maximum PoE power per port 30 W
Maximum PoE power per card 62 W Number of Sync-E ports 4 (all ports)
Number of Sync-E Tx clock domains 2 (System clock, PTP clock) Standards compliance IEEE802.3
ITU-T G.8262
6.13.6 DHGE_8
Interface connector type 4 x SFP
Supported port types 1000Base-SX, LX, EX, ZX, BD, Colored 100Base-FX (SM and MM)
10/100/1000Base-T Maximum number of 1000Base-X ports 8 (with CSFP)
4 (with SFP) Maximum number of 100Base-FX ports 8 (with CSFP)
4 (with SFP)
Maximum number of 10/100/1000Base-T ports 4 (with copper SFP – ETGBE)
Number of Sync-E ports 8 (all ports)
Number of Sync-E Tx clock domains 2 (System clock, PTP clock)
Standards compliance IEEE802.3
ITU-T G.8262
6.13.7 DHGE_16
Interface connector type 8 x RJ45
4 x SFP (SFP/CSFP compatible)
Supported port types 10/100/1000Base-Tx
1000Base-SX, LX, EX, ZX, BD, Colored 100Base-FX (SM and MM)
Maximum number of 10/100/1000Base-Tx
ports 8 +4 (with copper SFP – ETGBE)
Maximum number of 1000Base-X ports 8 (with CSFP) 4 (with SFP) Maximum number of 100Base-FX ports 8 (with CSFP)
4 (with SFP) Number of Sync-E ports 16 (all ports)
Number of Sync-E Tx clock domains 2 (System clock, PTP clock)
Standards compliance IEEE802.3
ITU-T G.8262
6.13.8 DHGE_24
Interface connector type 12 x SFP (SFP/CSFP compatible) Supported port types 1000Base-SX, LX, EX, ZX, BD, Colored
100Base-FX (SM and MM) Maximum number of 1000Base-X ports 24 (with CSFP)
12 (with SFP)
Maximum number of 100Base-FX ports 24 (with CSFP) 12 (with SFP) Maximum number of
10/100/1000Base-Tx ports 12 (with copper SFP – ETGBE) Number of Sync-E ports 24 (all ports)
Number of Sync-E Tx clock domains 2 (System clock, PTP clock)
Standards compliance IEEE802.3
ITU-T G.8262
6.13.9 DHFE_12
Interface connector type 12 x RJ-45
Supported port types 10/100Base-T
Maximum number of 10/100Base-T
ports 12
Standards compliance IEEE802.3
6.13.10 DHFX_12
Interface connector type 12 x SFP
Supported port types 100Base-FX
Maximum number of 100Base-FX ports 12
Standards compliance IEEE802.3
6.13.11 DMCES1_4
Interfaces 4 x channelized STM-1(SFP)
1 x channelized STM-4 (SFP) 1 x GbE SFP
CES service Unstructured E1 (SAToP)
Channelized E1 (CESoPSN)
Number of CES services 252
Encapsulation Protocol in standalone mode CESoETH, CESoIP/UDP Encapsulation Protocol in integration mode CESoETH and CESoMPLS CES clock recovery mechanism Adaptive Clock Recovery (ACR)
Differential Clock Recovery (DCR) Reference clock frequency for DCR RTP
timestamp 19.44 MHz
25 MHz
Number of ACR domains 32
Number of DCR domain 252
E1 Tx Timing mode Recovered from CES stream System timing
Loop timing
Payload time 125~8000us@125us
Jitter buffer Max delay var 1000-64000 @1000 µsec Jitter buffer Min latency 500-32000 @500 µsec
Standards compliance IEFT RFC4553, RFC5086
MEF8, MEF3
ITU-T Y.1413, G.707, G.783
6.13.12 DMCE1_32
Interfaces 32 x E1
1 x GbE Combo
CES service Unstructured E1 (SAToP)
Channelized E1 (CESoPSN)
Number of CES services 32
Encapsulation Protocol in standalone mode CESoETH, CESoIP/UDP Encapsulation Protocol in integration mode CESoETH, CESoMPLS CES clock recovery mechanism Adaptive
Differential Reference clock frequency for DCR RTP
timestamp 19.44 MHz
25 MHz
Adaptive timing domain 32
Differential timing domain 32
Tx Timing mode Recovered from CES stream
System timing Loop timing
Payload time 125~8000us@125us
Jitter buffer Max delay var 1000-64000 @1000 µsec Jitter buffer Min latency 500-32000 @500 µsec
Standards compliance IEFT RFC4553, RFC5086
MEF8, MEF3 ITU-T Y.1413, G.703
6.13.13 MSE1_16
Interfaces 16 x E1/T1
CES service Unstructured E1/T1 (SAToP)
Channelized E1/T1 (CESoPSN)
Number of CES service 16
Encapsulation Protocol CESoETH, CESoMPLS CES clock recovery mechanism Adaptive
Differential Reference clock frequency for DCR
RTP timestamp 19.44 MHz
25 MHz Adaptive timing domain 16 Differential timing domain 16
Tx Timing mode Recovered from CES stream
System timing Loop timing
Payload time 125~8000us@125us
Jitter buffer Max delay var 1000-64000 @1000 µsec Jitter buffer Min latency 500-32000 @500 µsec Standards compliance IEFT RFC4553, RFC5086
MEF8, MEF3 ITU-T Y.1413, G.703
6.13.14 MSC_2_8
Interfaces 2 x Channelized STM-1/OC-3 (SFP)
8 x E1/T1
CES service Unstructured E1/T1 (SAToP)
Channelized E1/T1 (CESoPSN) Number of CES service 126 x E1 (over 2 x STM1) + 8 x E1
OR
168 x DS1 (over 2 x OC-3) + 8 x DS1 Encapsulation Protocol CESoETH, CESoMPLS
CES clock recovery mechanism Adaptive Differential Reference clock frequency for DCR
RTP timestamp 19.44 MHz
25 MHz
Adaptive timing domain 134/176 (Per E1/DS1) Differential timing domain 134/176 (Per E1/DS1)
Tx Timing mode Recovered from CES stream
System timing Loop timing
Payload time 125~8000 µsec@125 µsec
Jitter buffer Max delay var 1000-64000 @1000 µsec
Jitter buffer Min latency 500-32000 @500 µsec Standards compliance IEFT RFC4553, RFC5086
MEF8, MEF3
ITU-T Y.1413, G.703, G.783
6.13.15 Ethernet Transceivers
Table 6-8: GbE/FX client transceivers
OTGBE_SX OTGBE_LX OTGBE_ZX OTGBE_EX OTFE_MM OTFE_SM
Transmitter type GbE/FC1/
FICON(2)
(nominal) (Gbps) 1.0625/1.25/
2.125 1.0625/1.25/
Table 6-9: GbE bidirectional client transceivers
OTGBE_S3BD OTGBE_S5BD OTGBE_L3BD OTGBE_L5BD OTGBE_L5BD80 OTGBE_L6BD8 0
Transmitter type Bidirectional SFP,
1310 nm Bidirectional SFP,
1490 nm Bidirectional SFP,
1310 nm e Bidirectional SFP,
1490 nm Bidirectional SFP,
1490 nm Bidirectional
SFP, 1590 nm Data rate (nominal)
(MBaud) 1250 1250 1250 1250 1250 1250
OTGBE_S3BD OTGBE_S5BD OTGBE_L3BD OTGBE_L5BD OTGBE_L5BD80 OTGBE_L6BD8
Typical Rx LOS level
(dBm) < -22 < -22 < -24 < -24 < -26 < -26
Table 6-10: CWDM and DWDM GbE transceivers
CWDM DWDM
SFP TRANSCEIVER NAME56 OTC25_PSxx OTC25_1ALxx OTR25_AVxx OTR25_ABxx
APPLICATION CODE57 S-C8S1-1D2/5
G.695
Operating wavelength (nm) 1464-1618 1464-1618 1530-1565 1530-1565
TRANSMITTER
56 New optical SFP transceivers for existing SIO16 basecard.
57 Application code is in reference to ITU-T Recommendation G.691.
CWDM DWDM
SFP TRANSCEIVER NAME56 OTC25_PSxx OTC25_1ALxx OTR25_AVxx OTR25_ABxx
Min. sensitivity (BER of 1*10-12) EOL (dBm) -21.5
(-23 GbE) -28
(-32 GbE) -28 -28
Min. overload (dBm) 0 -7 -9 -9
Max. receiver reflectance (dB) -27 -27 -27 -27
OPTICAL PATH BETWEEN S & R
Max. dispersion [ps/nm] 800
(40 km G.652) 1600
6.13.17 Ethernet SFP+ Transceivers
Table 6-11: ESFP+ transceivers
SFP+ TRANSCEIVER
NAME OTP10I_ER OTP10_ER OTP10_ZR OTP10_SR OTP10_LR OTP10_LRM OTP10Txx (Linear version) APPLICATION
CODE58 10GBASE-ER 10GBASE-ER L-64.2a P1L1-2D2
10GBASE-SR 10GBASE-LR 10GBASE-LRM ALLM (Limiting version) or ALLN (Linear version) TRANSMITTER
Operating
wavelength (nm) 1530-1565 1530-1565 1530-1565 840-860 1260-1355 1260-1355 C-Band Tunable 1528-1568
58 Application code is in reference to ITU-T Recommendation G.691.
SFP+ TRANSCEIVER
NAME OTP10I_ER OTP10_ER OTP10_ZR OTP10_SR OTP10_LR OTP10_LRM OTP10Txx (Linear version) APPLICATION
CODE58 10GBASE-ER 10GBASE-ER L-64.2a P1L1-2D2
10GBASE-SR 10GBASE-LR 10GBASE-LRM ALLM (Limiting version) or ALLN
Table 6-12: SFP+ bidirectional client transceivers
SFP+ TRANSCEIVER NAME OTP10_S27BD OTP10_S33BD OTP10_L27BD OTP10_L33BD
APPLICATION CODE59 10GBASE-S27BD 10GBASE-S33BD 10GBASE-L27BD 10GBASE-L33BD
Source type CWDM DFB CWDM DFB CWDM DFB CWDM DFB
Modulation N/A N/A N/A N/A
Operating output
wavelength (nm) 1260-1280 1320-1340 1260-1280 1320-1340
Direct max.-20 dB width
(nm) N/A N/A N/A N/A
Min. side mode
suppression ratio (dB) 30 30 30 30
59 Application code is in reference to ITU-T Recommendation G.691.
SFP+ TRANSCEIVER NAME OTP10_S27BD OTP10_S33BD OTP10_L27BD OTP10_L33BD
Sensitivity (BER of 1*10 12)
(dBm) -14 -14 -18 -18
Min. overload (dBm) 05 0.5 -5 -5
Maximum optical path
penalty 3.2 3.2 3.2 3.2
OCH switching time (ms) N/A N/A N/A N/A
Table 6-13: SFP+ C/DWDM transceivers
SFP+ TRANSCEIVER NAME OTP10C_PSxx OTP10D_ALxx
APPLICATION CODE60 PS AL
TRANSMITTER
Operating wavelength (nm) 1471, 1491, 1511, 1531, 1551, 1571, 1591,
1611 1529.55-1561.61
60 Application code is in reference to ITU-T Recommendation G.691.
SFP+ TRANSCEIVER NAME OTP10C_PSxx OTP10D_ALxx
APPLICATION CODE60 PS AL
RECEIVER
Max. attenuation (dB) 11.1 22
Min. Attenuation (dB) 5 10
Min. sensitivity (BER of 1*10-12)
EOL (dBm) -15.8 -23
Min. overload (dBm) -1 -7
Max. receiver reflectance (dB) -26 -27
OPTICAL PATH BETWEEN S & R
Max. dispersion [ps/nm] 800 1600
Min. optical return loss of cable (dB) 21 27
Max. discrete reflectance (dB) - -
Max. optical path penalty (dB) 3 3.5
OCH switching time (ms) - -
6.13.18 CSFP Client Transceivers
Table 6-14: CSFP client transceivers
CSFP TRANSCEIVER CTGBE_S3S5 CTGBE_S5S3 CTGBE_L3L5 CTGBE_L5L3 CTGBE_E3E5 CTGBE_E5E3
APPLICATION CODE61 S3S5 S5S3 L3L5 L5L3 E3E5 E5E3
TRANSMITTER
Operating wavelength (nm) 1310 1490 1310 1490 1310 1490
Source type FP DFB FP DFB DFB DFB
Max. RMS width (nm) 3.5 1 3.5 1 1
Min. side mode suppression (dB) - 30 - 30 - -
Min. mean launched power (dBm) -9 -9 -8 -8 -5 -5
Max. mean launched power (dBm) -3 -3 -2 -2 0 0
Min. extinction ratio (dB) 6 6 6 6 9 9
RECEIVER
Min. sensitivity (BER of 1*10-12)
EOL (dBm) -20 -20 -22.5 -22.5 -24 -24
Min. overload (dBm) -3 -3 -2 -2 0 0
61 Application code is in reference to ITU-T Recommendation G.691.
CSFP TRANSCEIVER CTGBE_S3S5 CTGBE_S5S3 CTGBE_L3L5 CTGBE_L5L3 CTGBE_E3E5 CTGBE_E5E3
APPLICATION CODE61 S3S5 S5S3 L3L5 L5L3 E3E5 E5E3
Max. receiver reflectance (dB) - - - - - -
OPTICAL PATH BETWEEN S & R
Max. dispersion [ps/nm] - - - - - -
Min. optical return loss of cable (dB) - - - -
Max. discrete reflectance (dB) - - - -
Max. optical path penalty (dB) - - - -
6.13.19 Electrical GbE SFP (ETGbE)
ETGBE Notes
Data rate 10/100/1000 Mbps IEEE 802.3 compatible
Connector RJ-45
Cable type CAT 5
Cable length 100m
6.14 MXP10 Base Card Configurations
Card No. of
ESlots Function/
Description
MXP10 1 Base card for multirate combiner, transponder or ADM on Card supporting 12 CSFP
(6 x SFP) ports of GbE, FC1/2/4, STM-1/4/16/64, OTU1. Supports FEC and EFEC on the line side.
6.14.1 MXP10 Base Card Modules and Transceivers
Card Function/
Description
Client module and transceivers for MXP10
OM_AOC4 Optical module for up to 4 x SFP based ports , one module per MXP10 card
Line transceivers for MXP10
OTP10C_PSxx Optical OTU2/OTU2e/STM64/10GE/FC-1200 transceiver, CWDM
OTP10D_ALxx Optical OTU2/OTU2e/STM64/10GE/FC-1200 transceiver, DWDM
OTP10T_AL Tunable SFP+
OTPMR10 Multi-rate SFP+ for OTU2/OTU2e/STM64/10GE/FC-800/FC-1200
OTPMRC/OTPMRC10 CWDM/DWDM Multi-rate SFP+ for OTU2/OTU2e/STM64/10GE/FC-800/FC-1200
Card Function/
Description
Client SFP transceivers for MXP10
Client SFP transceivers for MXP10