AA INT DGT: Controls the grace period between dialling valid digits before transferring call to INVLID DEST as set in MMC 733 on a per-plan basis.
AA NO ACT: Time AA will wait for first digit for processing, after which call is transferred to the desti-nation set in NO ACT DEST in MMC 733.
AA TRANS: After this time, compare input digit with AA translation table (MMC 732) and transfer to destination.
ALERT TONE: Sets the duration of the attention tone preceding a call to a keyset in the Voice An-nounce or Auto Answer mode. This tone also precedes a forced Auto Answer call.
ALM REM INTERVAL: Controls the time between ring attempts at a station when alarm reminder is set.
ALM REM RING OFF: Controls the length of the ring cycle when alarm reminder is set at a station.
ATT RECALL: The length of time a transfer recall will ring at a station before recalling the operator.
AUTO REDIAL INT: Controls the time between attempts after RETRY dialling is set on a station.
AUTO REDIAL RLS: Controls the duration of a Ring No Answer condition on a retry number dialled before the auto redial is automatically cancelled.
BARGE-IN TONE INT: Controls the interval between the tones sent to the station being barged in on.
CALLBACK NO ANS: Controls the time before the callback is automatically cancelled when a call-back detects Ring No Answer.
CAMP ON RECALL: Controls how long a camped-on call will stay at a destination before recalling to the transferring station.
play. While on a trunk conversation, users are allowed to review received CLIP by pressing SCROLL à CLIP soft key, but LCD will automatically go back to trunk conversation status on expiration of this timer.
CLIP MSG RECEIVE: The amount of time that the system will allow a valid message from the C.O.
C.O. CLEAR: The length of time a Direct Trunk Select key remains busy after cleardown.
CO CONFIRM: After this time, the outgoing call is disconnected or you can hear the confirm tone.
C.O.- C.O. DISCONNECT: Monitors the duration of an unsupervised conference; when it expires, both trunks are disconnected.
CONFER TONE INT: Controls the intervals between the tones heard by the parties in a conference.
CONFIRM TONE: The tone heard when a feature is activated or deactivated.
CRD TONE INT: Controls the interval of the intermittent tone presented to station users whose calls are being recorded using the Auto Record feature (see CADENCE documentation).
DIAL PASS: The wait time for preventing the misdialling of an outgoing call. After the last digit has been dialled, the voice path is connected.
DISA DISCONNECT: Controls the maximum duration of a DISA call.
DISA LOCK OUT: Controls the time period for which a DISA call is not allowed to be made after the DISA error counter has expired (MMC 500).
DISA NOANS DISC: Controls the time period after which a DISA call is disconnected if the call is not answered.
DISA PASS CHECK: Defines the time period before the system clears the incorrect passcode counter.
DISPLAY DELAY: Controls how long information is shown in the LCD. This timer also controls how long error tone is heard.
DOOR LOCK RELEASE: Controls how long the door lock relay is activated.
DOOR RING DETECT: Controls the period of time before a call is answered by the door phone.
DOOR RING OFF: Controls the duration of ringing at the door ring destination before automatically cancelling.
E-HOLD RECALL: Controls how long a call is held exclusively at a station before recalling. See ATT Recall Time.
EXT. FWD DELAY: Controls the External Call Forward feature which allows a station to ring before the call is placed on external call forwarding.
FIRST DIGIT: Controls how long the system will wait for dialling to begin before dropping the dial tone and returning the user to error tone.
HOK FLASH MAX: Monitors the duration of a hookswitch flash to ensure that the flash is valid and not a line noise or an accidental hookswitch bounce (LONGEST DURATION).
MMC 501 (Page 5 of 6)
HOK FLASH MIN: Monitors the duration of a hookswitch flash to ensure that the flash is valid and not a line noise or an accidental hookswitch bounce (SHORTEST DURATION).
HOOK OFF: Controls the time before dial tone is sent to a single line station.
HOOK ON: Sets the minimum amount of time that the system will recognise as an SLT hang up.
(Must be greater than HOK FLASH MAX.)
INQUIRY RELEASE: Monitors the duration of the action of the soft key to determine when to return the LCD back to a normal status. This timer affects only display phones.
INTER DIGIT: Controls the grace period between dialling valid digits before dropping the call and returning the user to error tone.
KMMC LOCK OUT: Controls the grace period between programming actions while in a ming session (KMMC not PCMMC). The timer automatically returns the system to secure program-ming status.
LCR ADVANCE: Controls the period of time before selecting the next allowable route when a station is allowed to route advance.
LCR INTER DIGIT: Controls the grace period between dialling valid digits before dropping the call and returning the user to error tone.
MCL DELAY: Controls the time when the system should start transmitting Authorisation Code after sending MCL access code (Cable & Wireless 131 access).
OFF HOOK RING: Controls the duration of time between ring bursts to a user who has a camped-on call.
OFF HOOK SELECT: Controls the grace period before placing a internal/external call as pro-grammed in MMC 306.
OHVA ANSWER: Controls the duration of an OHVA call before automatic rejection. When a user re-ceives OHVA with voice interrupt, this situation will last until this timer expires. If LCD phones receive OHVA, REJECT will appear at righthand side of bottom line while this timer is activated.
OVERLAP INT DGT: Controls the grace period between receiving address information in overlap receiving mode via BRI/PRI line. After expiration of this timer the system operator will be alerted.
PAGE TIME OUT: Controls the duration of a page announcement.
PAGE TONE: Controls the duration of tone burst heard over the page prior to the page announce-ment.
PARK RECALL: Controls the period of time a call is parked before recalling to the call park origina-tor.
PC-MMC LOCK: Monitors PCMMC activity, drops the link if no action is created by PCMMC and re-turns the system to secure program status.
PERI UCD REPORT: Controls the interval between periodic UCD reports being output to the appli-cable port.
POWER DOWN: Sets the duration of disconnect signal for VM/AA ports.
RECALL DISCONNECT: The time an attendant recall rings before being disconnected. See ATT Re-call Time.
it recalls to the operator.
SMDR START/DIAL PULSE (ROTARY): This grace period timer starts SMDR recording for rotary dialling. This timer also controls the LCD duration timer on the keysets. The duration time displayed and the SMDR time duration will be the same.
SMDR START/DTMF: This grace period timer starts SMDR recording for touchtone dialling. This timer also controls the LCD duration timer on the keysets. The duration time displayed and the SMDR time duration will be the same.
SYS HOLD RECALL: Determines the time calls can be left on hold before recalling the holding sta-tion. Setting timer to 000 means no recalling will take place.
TRANSFER RECALL: Determines the time that transferred calls ring before recalling. See Recall Wait Time.
UCDS AUDIO ALARM: Determines how long the longest waiting call can be held before the system gives an audio alarm to the UCD supervisor.
UCDS VISUAL ALARM: Determines how long the longest waiting call can be held before the system gives a visual alarm to the UCD supervisor.
VMS UCD MSG: Not used in UK.
VOICE DIAL DELAY: Monitors the duration of the interaction between main software and Voice Dial-ler.
MMC 502 (Page 1 of 2)