User Guide. Linksys E1000. Wireless-N Router

(1)

Linksys E1000

Wireless-N Router

(2)

Linksys E1000

Chapter 1: Product Overview

Thank you for choosing the Linksys E1000 Wireless-N Router . The Router lets you access the Internet via a wireless connection or through one of its four switched ports . You can also use the Router to share resources such as computers, printers and files .

A variety of security features help to protect your data and your privacy while you are online . Security features include Wi-Fi Protected Access 2 (WPA2) security, which encrypts data on your wireless network; a Stateful Packet Inspection (SPI) firewall to help block unauthorized access to your Router; and Network Address Translation (NAT) technology, which enhances network protection by allowing your computers to share Internet access through a single, public Internet IP address . (IP stands for Internet Protocol .)

Setup and use of the Router is easy using Cisco Connect, the software that is installed when you run the included CD . Advanced configuration of the Router is available through the provided browser-based utility .

Top

1, 2, 3, 4 (Blue) These numbered LEDs, corresponding with the numbered ports on the Router’s back panel, serve two purposes . The LED is continuously lit when the Router is connected to a device through that port . It flashes to indicate network activity over that port .

Wi-Fi Protected Setup Button If you have client devices, such as wireless adapters, that support Wi-Fi Protected Setup, then you can use the Wi-Fi Protected Setup button to automatically configure wireless security for your wireless network .

To use Wi-Fi Protected Setup, refer to Wi-Fi Protected Setup, page 20 .

Wireless (Blue) The Wireless LED lights up when the wireless feature is enabled . It flashes when the Router sends or receives data over the wireless network .

Internet (Blue) The Internet LED lights up when there is a connection made through the Internet port . It flashes to indicate network activity over the Internet port .

Power (Blue) The Power LED lights up when the Router is powered on . When the Router goes through its self-diagnostic mode during every boot-up, the LED flashes . When the diagnostic is complete, the LED is continuously lit .

Back

Internet 4 3Ethernet2 1 Reset Power12VDC

Internet Using an Ethernet cable (also called a network or Internet cable), the Internet port connects the Router to your Internet connection, which is typically a cable or Digital Subscriber Line (DSL) modem .

4, 3, 2, 1 Using Ethernet cables, these Ethernet ports (4, 3, 2, 1) connect the Router to computers and other Ethernet network devices on your wired network .

Reset The Reset button is located on the right side of the product label . There are two ways to reset the Router to its factory defaults . Either press and hold the Reset Button for approximately five seconds, or restore the defaults from the

Administration > Factory  Defaults screen in the Router’s browser-based utility (refer to Administration > Factory Defaults, page 34) .

Power The Power port connects to the included power adapter .

Horizontal Placement

The Router has four rubber feet on its bottom panel . Place the Router on a level surface near an electrical outlet .

(5)

Linksys E1000

Chapter 1: Product Overview

Wireless-N Router

Wall-Mounting Placement

The Router has two wall-mount slots on its bottom panel . The distance between the slots is 152 mm .

Two screws are needed to mount the Router .

Suggested Mounting Hardware

2 .5-3 .0 mm

4-5 mm 1-1 .5 mm

NOTE: Cisco is not responsible for damages incurred by unsecured wall-mounting hardware . Follow these instructions:

1 . Determine where you want to mount the Router . Make sure that the wall you use is smooth, flat, dry, and sturdy . Also make sure the location is within reach of an electrical outlet .

2 . Drill two holes into the wall . Make sure the holes are 152 mm apart .

3 . Insert a screw into each hole and leave 3 mm of its head exposed .

4 . Position the Router so the wall-mount slots line up with the two screws .

5 . Place the wall-mount slots over the screws and slide the Router down until the screws fit snugly into the wall-mount slots .

152 mm

Wall-Mounting Template

Print this page at 100% size .

(6)

Chapter 2: Cisco Connect

During installation, the setup software installs Cisco Connect on your computer . Cisco Connect offers options to connect additional computers or devices to the Router and allows you to change the Router’s settings .

Installation

To install the Router:

1 . Insert the CD into your CD-ROM drive .

Insert CD

2 . Click Set up your Linksys Router .

DVD/CD-RW Drive (E:) Linksys Router Setup

AutoPlay

Always do this for software and games:

Install or run program General options

Set up your Linksys Router

Published by Cisco Consumer Products LLC

Set AutoPlay defaults in Control Panel

Open folder to view files

using Windows Explorer

Speed up my system

using Windows ReadyBoost

DVD/CD-RW Drive (E:) Linksys Router Setup

Always do this for software and games: Install or run program

General options

Set up your Linksys Router

Published by Cisco Consumer Products LLC

Set AutoPlay defaults in Control Panel

Open folder to view files

using Windows Explorer

Speed up my system

using Windows ReadyBoost

Set Up Your Linksys Router

If you do not see this, access setup on the CD directly . To do so, perform the following steps for your specific operating system:

Windows 7

a . Go to Start > Computer . b . Double-click your CD-ROM drive . Windows Vista

a . Go to Start > Computer . b . Double-click your CD-ROM drive . Windows XP

a . Go to Start > My Computer and select your CD-ROM drive .

b . Double-click Setup.exe .

Mac OS X

a . Double-click the CD on your desktop . b . Double-click Setup .

3 . Read the Software End User License Agreement . To accept the agreement and continue with the installation, click Next .

License Agreement

4 . The connection steps are displayed .

Connection Overview

a . Plug the power cord into the Power port on the back of the Router .

(7)

Linksys E1000

Chapter 2: Cisco Connect

Wireless-N Router

b . Plug the power adapter into an electrical outlet .

Connect to Electrical Outlet

c . Unplug the existing Ethernet cable from your computer and plug it into the yellow port labeled Internet on the back of the Router . Click Next .

Connect Ethernet Cable

NOTE: You can view detailed connection steps by clicking in the setup software .

NOTE: If the setup software detects multiple routers, then select the serial number of your Router . The serial number is located on the left side of the product label, which is on the bottom of the Router .

5 . Please wait while the setup software is setting up the Router .

Please Wait

6 . The installation is complete . Click OK .

Installation is Complete

NOTE: If you have any problems during the installation process, refer to the Frequently Asked Questions in the setup software, or use a computer with an active Internet connection to visit www.linksys.com/support .

Main Menu

When Cisco Connect starts up, the main menu appears:

Main Menu

Status information is displayed in the upper right corner:

• online secure

Your local network is secure, and your Internet connection is available .

• offline secure

Your local network is secure; however, your Internet connection is not available . To repair your Internet connection, follow the on-screen instructions .

NOTE: A group of computers or other devices connected to a router is a local network . The router allows the networked devices to communicate with each other .

(8)

The main menu offers four options: Computers and devices, Parental controls, Guest access, and Router settings .

NOTE: To view the FAQs for more information, click Need help?

Local Access versus Guest Access

You can connect computers or devices to your Router by giving them local access (Computers and devices option)or guest access (Guest access option) .

Computers and devices with local access will have access to the Internet and to other devices on your local network, including shared computers and printers that are connected to the Router . Local access can be given to a wired or wireless device . Refer to Computers and Other Devices, page 6 for more information .

Guest access allows you to provide guests visiting your home with Internet access . Your guests will not have access to your other computers or personal data . Provide your guest with the guest network name and password . Guest computers must connect to your network using a wireless network connection . Refer to Main Menu – Guest Access, page 5 and Guest Access, page 10 for more information . The following diagram shows a typical example of how local access and guest access are used in the same home .

Guest Access versus Local Access Diagram

12

Internet

Guest Notebook

Family Notebook Printer

Modem Router

Guest Access (Internet Access Only) Local Access

Main Menu – Computers and Devices

Use this option to connect another computer or device to the Router .

There is x device(s) connected to your router The number of devices connected to the Router is displayed .

Add device To connect another computer or device to the Router, click Add device and go to Computers and Other Devices, page 6 .

Main Menu – Parental Controls

Parental controls restrict Internet access for up to five computers . For the computers you select, you can block or limit Internet access to specific times . You can also block specific websites .

Parental controls restrictions are being applied to x device(s) The number of devices with parental controls restrictions is displayed .

Change To enable parental controls or change settings, click Change and go to Parental Controls, page 8 .

Main Menu – Guest Access

Guest access provides Internet access only; it does not provide access to the local network and its resources . For example, the guest computer cannot print to a printer on the local network or copy files to a computer on the local network .

Guest access helps minimize exposure of your local network . To grant Internet access to friends or family, provide the guest network name and password displayed on this screen .

Guests can connect to x-guest using the password xyz When a guest wants Internet access in your home, have the guest do the following:

1 . Connect to the wireless guest network, which is the name of your wireless network followed by -guest . 2 . Open a web browser .

3 . On the login screen, enter the password of your guest network . Then click Login .

Change To disable guest access or change settings, click Change and go to Guest Access, page 10 .

Main Menu – Router Settings

Use this option to personalize the Router’s settings .

Router name is x The name of the Router is displayed .

Change To change settings, click Change and go to Router Settings, page 10 .

(9)

Linksys E1000

Chapter 2: Cisco Connect

Wireless-N Router

Computers and Other Devices

The Computers and other devices screen appears .

Computers and Other Devices

Computer Click this option to connect another computer in your home . Go to Computer, page 6 .

Wireless printer Click this option to connect a wireless printer . Go to Wireless Printer, page 7 .

Other devices Click this option to connect a device that is not a computer, such as a smartphone or game console . Go to Connect Manually, page 7 .

Computer

You can use a USB flash drive to create an Easy Setup Key, which holds the wireless settings for the Router . Then you can use the Easy Setup Key to connect additional computers to the Router . Select the appropriate option:

Yes, I have an Easy Setup Key If you already have an Easy Setup Key, select this option . Click Next and go to Connect with the Easy Setup Key, page 6 .

No, I don’t have an Easy Setup Key — create a new one now If you want to create or update an Easy Setup Key, select this option . Click Next and go to Create or Update the Easy Setup Key, page 7 .

I want to connect manually using my wireless settings If you want to connect manually (without an Easy Setup Key), select this option . Click Next and go to Connect Manually, page 7 .

Do You Have an Easy Setup Key?

Connect with the Easy Setup Key

1 . Insert the Easy Setup Key into an available USB port on the computer that you want to connect to the Router .

Connecting Another Computer

2 . On that computer, click Connect to your Linksys Router . (If you do not see this, access the Easy Setup Key through Windows Explorer or the Finder, and double-click Connect .)

Follow the on-screen instructions to connect that computer to the Router .

3 . Come back to this computer . On the Connecting  another computer screen, click Next .

4 . Enter a name that will be used to identify the newly added computer . Then click Finish .

(10)

Create or Update the Easy Setup Key

If you do not have an Easy Setup Key, then you can create one using a USB flash drive . If you already have an Easy Setup Key, then you can update it with the Router’s current settings .

1 . Insert the Easy Setup Key or a USB flash drive into an available USB port on your computer .

Update or Create an Easy Setup Key

2 . Please wait while settings are copied to the Easy Setup Key .

Copying Files to the Easy Setup Key

3 . Remove the Easy Setup Key . You can now use it to connect other computers to the Router (for more information, refer to Connect with the Easy Setup Key, page 6) . Click Close .

Easy Setup Key Has Been Updated

Connect Manually

1 . Enter the Network name (SSID), Security Key, and Security  Type settings on your wireless device (SSID stands for Service Set Identifier) . To print this information, click Print these settings .

Connecting a Device

2 . After your device connects, click Next .

3 . Enter a name that will be used to identify this device . Then click Finish .

Name Your Device

Wireless Printer

1 . Refer to your printer’s documentation to learn how to connect it to a wireless printer .

2 . Enter the  Network  name  (SSID), Security  Key, and

Security Type settings on your wireless printer . To print this information, click Print these settings .

(11)

Linksys E1000

Chapter 2: Cisco Connect

Wireless-N Router

3 . Wait until your printer connects . On the Connecting a  wireless printer screen, click Next .

4 . Enter a name that will be used to identify this printer . Then click Finish .

Name Your Printer

Parental Controls

The Parental controls screen appears .

Parental Controls Password

First-Time Access of Parental Controls

1 . The first time you access parental controls, you will be asked to set up a parental controls password . Complete the following:

• Parental controls password This password protects access to parental controls . Create a password of 4-32 characters .

• Verify password Re-enter the password .

• Secret question Create a secret question and answer pair . If you forget the password, you can reset it by correctly answering the secret question . Enter your question .

• Answer Enter the answer to your secret question . Click OK to save your settings .

2 . Select the computer whose parental controls you want to set up . Then click OK .

Set Up Parental Controls For

3 . The Parental controls main screen appears .

Parental Controls

You have the following options:

Restrict Internet access on The list of computer(s) you have selected for parental controls is displayed . To add, remove, or rename computers on this list, refer to Restrict Internet Access List, page 9 . To set up parental controls on a computer, refer to Set Up Parental Controls, page 9 .

Change parental controls password Click this option to change the password that protects access to parental controls . Refer to Change Parental Controls Password, page 10 .

(12)

Restrict Internet Access List

Parental Controls

Add If you want to apply parental controls to additional computers, click Add .

If you clicked Add, the Set up parental controls for screen appears .

Set Up Parental Controls For

Select the computer whose parental controls you want to set up . Then click OK .

Remove If there is a computer that should not have parental controls applied, select the computer and click Remove .

Rename To give a computer a new name, select the computer and click Rename .

If you clicked Rename, the Rename  the  device screen appears .

Rename the Device

Enter the new name . Then click Rename .

Set Up Parental Controls

To set up parental controls for a computer, follow these instructions:

1 . Select the computer from the Restrict Internet access on

list . (If the computer is not listed, click Add to select the computer .)

Parental Controls

2 . The Block Internet access option offers the following:

• Always To always block Internet access, select this option .

• Specific times To block Internet access during specific days and times, select this option and set the schedule:

– School nights Select the appropriate start and end times .

– Weekends Select the appropriate start and end times

• Never To always allow Internet access, keep the default, Never .

3 . For the Block specific sites option, click Edit to create a list of websites you want to block . By default, the list is empty .

If you clicked Edit, the Block these sites screen appears .

Block These Sites

a . Enter a website address on each line . b . Click Save to save your settings .

4 . On the Parental  controls screen, click Finish to save your settings .

(13)

Linksys E1000

Chapter 2: Cisco Connect

Wireless-N Router

NOTE: Repeat steps 1-4 to set up parental controls for different computers .

Change Parental Controls Password

If you clicked Change parental controls password, the

Change your parental controls password screen appears .

Change Your Parental Controls Password • Old password Enter the old password .

• New password Enter a new password of 4-32 characters .

• Verify password Re-enter the new password . Click Change to save your setting .

Guest Access

The Guest access settings screen appears .

Guest Access Settings

Allow guest access By default, guest access is enabled . To disable guest access, select no .

Guest network name By default, the setup software sets up the name of the guest network .

Password By default, the setup software sets up the password for the guest network . To change the password, click Change .

If you clicked Change, the Change guest password screen appears .

Change Guest Password

• Enter a new guest password Enter a password of 4-32 characters .

• Click Change to save your setting .

Total guests allowed By default, 5 guests are allowed Internet access through the guest network . Select the appropriate number of guests allowed on your guest network; you can select up to 10 guests .

Click Finish to save your settings .

Router Settings

The Router settings screen appears .

Router Settings

Personalize

Router name The name of the Router is displayed (this is also the name of your wireless network) . To change the name, click Change and go to Change Router Name or Password, page 11 .

Password The password that protects access to the Router’s settings is displayed (this also protects wireless access to your local network) . To change the password, click Change and go to Change Router Name or Password, page 11 .

(14)

Easy Setup Key

Update or create key The Easy Setup Key is a USB flash drive that holds the wireless settings for the Router . If you want to create or update an Easy Setup Key, click this option and go to Create or Update the Easy Setup Key, page 7 .

Other Options

Register now to receive special offers and updates To sign up to receive special offers and updates, click this option .

Router details To view more information about the Router, click this option and go to Router Details, page 11 .

Advanced settings To access settings for advanced users, click this option and go to Advanced Settings, page 12 .

Click Finish to save your settings .

Change Router Name or Password

NOTE: If you change the Router name or password, you also change the name or password of your wireless network . The wireless computers or other devices connected to the Router will need to be reconnected using the new name or password (for more information, refer to Computers and Other Devices, page 6) .

If you clicked Change, the Changing  router  name  or  password screen appears .

1 . To change the Router name or password, click Yes . Otherwise, click No .

Changing Router Name or Password

2 . Complete the following:

• Router name Enter a name of 1-32 characters .

• Password Enter a password of 8-63 characters .

• Click Change to save your settings .

Change Router Name and Password

Router Details

The Router  details screen appears, displaying the Model name, Model number, Serial number, Firmware version, Operating system, Software version, Connection type (WAN), IP address (LAN), IP address (WAN), and Computer IP address . (WAN stands for Wide Area Network, such as the Internet . IP stands for Internet Protocol . LAN stands for Local Area Network .)

Copy To copy the details to a text file, click Copy and follow these instructions:

1 . Open a text editor, such as Microsoft Word or Notepad . 2 . Go to Edit > Paste .

3 . Go to File > Save .

Router Details

(15)

Linksys E1000

Chapter 2: Cisco Connect

Wireless-N Router

Advanced Settings

If you are an advanced user familiar with router administration, you can access the browser-based utility to use the advanced configuration settings of the Router .

Username Enter this username to access the browser-based utility .

Password Enter this password to access the browser-based utility .

Copy password To copy the password to the Clipboard, click this option .

Advanced Settings

Click OK to open the web browser and access the browser-based utility . For more information, refer to How to Access the Browser-Based Utility, page 13 .

How to Exit Cisco Connect

To exit Cisco Connect, click Close on the main menu .

Main Menu

How to Access Cisco Connect

Windows

To access Cisco Connect, go to Start > All Programs > Cisco Connect .

Mac

To access Cisco Connect, go to Go > Applications > Cisco Connect .

(16)

Chapter 3: Advanced Configuration

After setting up the Router with the setup software (located on the CD-ROM), the Router will be ready for use . If you would like to change its advanced settings, use the Router’s browser-based utility . This chapter describes each web page of the utility and each page’s key functions . You can access the utility via a web browser on a computer connected to the Router .

The browser-based utility has these main tabs: Setup,

Wireless, Security, Access  Restrictions, Applications  &  Gaming, Administration, and Status . Additional tabs will be available after you click one of the main tabs .

How to Access the Browser-Based Utility

To access the browser-based utility, launch the web browser on your computer, and enter the Router’s default Internet Protocol (IP) address, 192.168.1.1, or the Router’s default Uniform Resource Locator (URL) address, my.E1000, in the Address field . Then press Enter .

A login screen will appear . (Non-Windows 7 users will see a similar screen .) Leave the User  name field blank . Then enter the password you set up during the setup software . (If you did not run the setup software, then use the default password, admin . You can set a new password on the  Administration  >  Management screen . Refer to Administration > Management, page 32 .) Click OK to continue .

Login Screen

NOTE: You can also access the browser-based utility through Cisco Connect . For more information, refer to Router Settings, page 10 .

Setup > Basic Setup

The first screen that appears is the Basic Setup screen . This allows you to change the Router’s general settings .

Setup > Basic Setup

Language

Language To use a different language, select one from the drop-down menu . The language of the browser-based utility will change five seconds after you select another language .

Click Save Settings to apply your changes, or click Cancel Changes to clear your changes .

Internet Setup

The Internet Setup section configures the Router to your Internet connection . Most of this information can be obtained through your Internet Service Provider (ISP) .

Internet Connection Type

Select the type of Internet connection your ISP provides from the drop-down menu . The available types are:

• Automatic Configuration - DHCP

• Static IP

• PPPoE

• PPTP

• L2TP

(17)

Wireless-N Router

Linksys E1000

Chapter 3: Advanced Configuration

Automatic Configuration - DHCP

The default Internet Connection Type is set to Automatic Configuration - DHCP (Dynamic Host Configuration Protocol) . Keep the default only if your ISP supports DHCP or if you connect using a dynamic IP address . (This option usually applies to cable connections .)

Internet Connection Type > Automatic Configuration - DHCP

Static IP

If you are required to use a permanent IP address to connect to the Internet, select Static IP .

Internet Connection Type > Static IP

Internet IP Address This is the Router’s IP address, when seen from the Internet . Your ISP will provide you with the IP address you need to enter here .

Subnet Mask This is the Router’s Subnet Mask, as seen by users on the Internet (including your ISP) . Your ISP will provide you with the Subnet Mask .

Default Gateway Your ISP will provide you with the Gateway address, which is the ISP server’s IP address .

DNS 1-3 Your ISP will provide you with at least one DNS (Domain Name System) server IP address .

PPPoE

Some DSL-based ISPs use Point-to-Point Protocol over Ethernet (PPPoE) to establish Internet connections . If you are connected to the Internet through a DSL line, check with your ISP to see if they use PPPoE . If they do, you will have to enable PPPoE .

Internet Connection Type > PPPoE

Username and Password Enter the Username and Password provided by your ISP .

Service Name (optional) If provided by your ISP, enter the Service Name .

Connect on Demand: Max Idle Time You can configure the Router to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time) . If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again . To use this option, select Connect on Demand . In the Max Idle Time

field, enter the number of minutes you want to elapse before your Internet connection terminates . The default is 5 minutes .

Keep Alive: Redial Period If you select this option, the Router will periodically check your Internet connection . If you are disconnected, then the Router will automatically re-establish your connection . To use this option, select Keep Alive . In the Redial Period field, specify how often the Router should check the Internet connection . The default is 30 seconds .

PPTP

Point-to-Point Tunneling Protocol (PPTP) is a service that applies to connections in Europe only .

Internet Connection Type > PPTP

If your ISP supports DHCP or you are connecting through a dynamic IP address, then select Obtain an IP Address Automatically . If you are required to use a permanent IP address to connect to the Internet, then select Specify an IP Address . Then configure the following:

Specify an IP Address This is the Router’s IP address, as seen from the Internet . Your ISP will provide you with the IP address you need to specify here .

Subnet Mask This is the Router’s Subnet Mask, as seen by users on the Internet (including your ISP) . Your ISP will provide you with the Subnet Mask .

Default Gateway Your ISP will provide you with the Gateway address, which is the ISP server’s IP address .

(18)

DNS 1-3 Your ISP will provide you with at least one DNS (Domain Name System) Server IP address .

PPTP Server IP Address Your ISP will provide you with the IP address of the PPTP server .

L2TP

Layer 2 Tunneling Protocol (L2TP) is a service that applies to connections in Israel only .

Internet Connection Type > L2TP

Server IP Address This is the IP address of the L2TP Server . Your ISP will provide you with the IP address you need to specify here .

Telstra Cable

Telstra Cable is a service that applies to connections in Australia only .

Internet Connection Type > Telstra Cable

Server IP Address This is the IP address of the Telstra Cable . Your ISP will provide you with the IP address you need to specify here .

(19)

Wireless-N Router

Linksys E1000

Chapter 3: Advanced Configuration

Optional Settings

Some of these settings may be required by your ISP . Verify with your ISP before making any changes .

Optional Settings

Host Name and Domain Name These fields allow you to supply a host and domain name for the Router . Some ISPs, usually cable ISPs, require these names as identification . You may have to check with your ISP to see if your broadband Internet service has been configured with a host and domain name . In most cases, leaving these fields blank will work .

MTU MTU is the Maximum Transmission Unit . It specifies the largest packet size permitted for Internet transmission . Select Manual if you want to manually enter the largest packet size that is transmitted . To have the Router select the best MTU for your Internet connection, keep the default setting, Auto .

Size When Manual is selected in the MTU field, this option is enabled . Leave this value in the 1200 to 1500 range . The default size depends on the Internet Connection Type:

• DHCP, Static IP, or Telstra: 1500

• PPPoE: 1492

• PPTP or L2TP: 1460

Network Setup

The Network Setup section configures the IP settings for your local network .

Router IP

IP Address The Router’s IP address, as seen by your network, is displayed . The default Router IP address is 192.168.1.1 .

Subnet Mask The Router’s Subnet Mask, as seen by your network, is displayed .

URL Address To access the browser-based utility, you enter the Router’s IP address or URL address . The default is http://my.E1000 . If you want to change the default, enter a new URL address .

Router IP

DHCP Server Settings

The settings allow you to configure the Router’s DHCP server function . The Router can be used as a DHCP server for your network . A DHCP server automatically assigns an IP address to each computer or device on your network . If you choose to enable the Router’s DHCP server option, make sure there is no other DHCP server on your network .

DHCP Server Setting

DHCP Server DHCP is enabled by factory default . If you already have a DHCP server on your network, or you do not want a DHCP server, then select Disabled (no other DHCP features will be available) .

DHCP Reservation Click DHCP Reservation if you want to assign a fixed local IP address to a MAC address . DHCP Reservation

You will see a list of DHCP clients with the following information: Client Name, Interface, IP Address, and MAC Address .

DHCP Reservation

• Select Clients from DHCP Table Click the Select check box to reserve a client’s IP address . Then click Add Clients .

(20)

• Manually Adding Client To manually assign an IP address, enter the client’s name in the Enter  Client  Name field . Enter the IP address you want it to have in the Assign IP Address field . Enter its MAC address in the

To This MAC Address field . Then click Add . Clients Already Reserved

A list of DHCP clients and their fixed local IP addresses will be displayed at the bottom of the screen . If you want to remove a client from this list, click Remove . Click Save Settings to apply your changes, or click Cancel Changes to clear your changes . To update the on-screen information, click Refresh . To exit this screen, click Close .

Start IP Address The Start IP Address specifies the starting IP address for the range of addresses assigned by your Router when it functions as a DHCP server . (The first IP address assigned by the Router will be randomly selected within the range you specify .)

Because the Router’s default IP address is 192 .168 .1 .1, the Start IP Address must be 192 .168 .1 .2 or greater, but smaller than 192 .168 .1 .254 . The default Start IP Address is 192.168.1.100 .

Maximum Number of Users Enter the maximum number of computers that you want the DHCP server to assign IP addresses to . This number cannot be greater than 253 . The default is 50 .

IP Address Range The range of available IP addresses is displayed .

Client Lease Time The Client Lease Time is the amount of time a network user will be allowed connection to the Router with their current dynamic IP address . Enter the amount of time, in minutes, that the user will be “leased” this dynamic IP address . After the time is up, the user will be automatically assigned a new dynamic IP address, or the lease will be renewed . The default is 0 minutes, which means one day .

Static DNS 1-3 The Domain Name System (DNS) is how the Internet translates domain or website names into Internet addresses or URLs . Your ISP will provide you with at least one DNS Server IP address . If you wish to use another, enter that IP address in one of these fields . You can enter up to three DNS Server IP addresses here . The Router will use these for quicker access to functioning DNS servers .

WINS The Windows Internet Naming Service (WINS) manages each computer’s interaction with the Internet . If you use a WINS server, enter that server’s IP address here . Otherwise, leave this blank .

Time Settings

Time Setting

Time Zone Select the time zone in which your network functions from this drop-down menu .

Automatically adjust clock for daylight saving changes Select this option to have the Router automatically adjust for daylight saving time .

Setup > DDNS

The Router offers a Dynamic Domain Name System (DDNS) feature . DDNS lets you assign a fixed host and domain name to a dynamic Internet IP address . It is useful when you are hosting your own website, File Transfer Protocol (FTP) server, or other server behind the Router .

Before you can use this option, you need to sign up for DDNS service with a DDNS service provider, www.dyndns.org or www.tzo.com . If you do not want to use this option, keep the default, Disabled .

DDNS

DDNS Service

If your DDNS service is provided by DynDNS .org, then select DynDNS.org from the drop-down menu . If your DDNS service is provided by TZO, then select TZO.com . The options available on the DDNS screen will vary, depending on which DDNS service provider you use . DynDNS .org

Setup > DDNS > DynDNS

(21)

Wireless-N Router

Linksys E1000

Chapter 3: Advanced Configuration

Password Enter the Password for your DDNS account .

Host Name The DDNS URL assigned by the DDNS service is displayed .

System Select the DynDNS service you use: Dynamic, Static, or Custom . The default selection is Dynamic .

Mail Exchange (Optional) Enter the address of your mail exchange server, so emails to your DynDNS address go to your mail server .

Backup MX This option allows the Mail eXchange (MX) server to be a backup . To disable this option, keep the default, Disabled . To enable the option, select Enabled . If you are not sure which setting to select, keep the default, Disabled .

Wildcard This setting enables or disables wildcards for your host . For example, if your DDNS address is

myplace.dyndns.org and you enable wildcards, then

x.myplace.dyndns.org will work as well (x is the wildcard) . To disable wildcards, keep the default, Disabled . To enable wildcards, select Enabled . If you are not sure which setting to select, keep the default, Disabled .

Internet IP Address The Router’s Internet IP address is displayed here . Because it is dynamic, it will change .

Status The status of the DDNS service connection is displayed .

Update To manually trigger an update, click Update . Click Save Settings to apply your changes, or click Cancel Changes to clear your changes .

TZO .com

Setup > DDNS > TZO

E-mail Address, TZO Key, and Domain Name Enter the settings of the account you set up with TZO .

Internet IP Address The Router’s Internet IP address is displayed here . Because it is dynamic, it will change .

Status The status of the DDNS service connection is displayed .

Update To manually trigger an update, click Update .

Setup > MAC Address Clone

A Media Access Control (MAC) address is a 12-digit code assigned to a unique piece of hardware for identification . Some ISPs require you to register a MAC address in order to access the Internet . If you have your computer’s MAC address registered with your ISP and you do not wish to re-register the MAC address, then you may assign the registered MAC address to the Router with the MAC Address Clone feature .

Setup > MAC Address Clone

MAC Address Clone

Enabled/Disabled To have the MAC address cloned, select Enabled .

MAC Address Enter the MAC address registered with your ISP here .

Clone My PC’s MAC Click this button to clone the MAC address of the computer you are using .

(22)

Setup > Advanced Routing

This screen is used to set up the Router’s advanced functions . Operating Mode allows you to select the type(s) of advanced functions you use . Dynamic Routing automatically adjusts how packets travel on your network . Static Routing sets up a fixed route to another network destination .

Setup > Advanced Routing

Advanced Routing

NAT

Enabled/Disabled If this Router is hosting your network’s connection to the Internet, keep the default, Enabled . If another router exists on your network, select Disabled . When the NAT setting is disabled, dynamic routing will be enabled .

Dynamic Routing (RIP)

Dynamic routing uses the Routing Information Protocol (RIP) . This option enables the Router to automatically adjust to physical changes in the network’s layout and exchange routing tables with the other router(s) . The Router determines the network packets’ route based on the fewest number of hops between the source and the destination .

Enabled/Disabled When the NAT setting is enabled, the Dynamic Routing option is automatically disabled . When the NAT setting is disabled, this option is available . Select Enabled to use the Dynamic Routing option .

Static Routing

A static route is a pre-determined pathway that network information must travel to reach a specific host or network . Enter the information described below to set up a new static route .

Route Entries To set up a static route between the Router and another network, select a number from the drop-down list . Click Delete This Entry to delete a static route .

Enter Route Name Enter a name for the Route here, using a maximum of 25 alphanumeric characters .

Destination LAN IP The Destination LAN (Local Area Network) IP is the address of the remote network or host to which you want to assign a static route .

Subnet Mask The Subnet Mask determines which portion of a Destination LAN IP address is the network portion, and which portion is the host portion .

Gateway This is the IP address of the gateway device that allows for contact between the Router and the remote network or host .

Interface This interface tells you whether the Destination IP address is on the LAN & Wireless (Ethernet and wireless networks) or the Internet (WAN) . (WAN stands for Wide Area Network .)

Click Show Routing Table to view the static routes you have already set up .

Advanced Routing > Routing Table

Routing Table

For each route, the Destination LAN IP address, Subnet Mask, Gateway, and Interface are displayed . Click Refresh to update the information . Click Close to exit this screen .

Wireless > Basic Wireless Settings

The basic settings for wireless networking are set on this screen .

There are two ways to configure the Router’s wireless network(s), manual and Wi-Fi Protected Setup .

Wi-Fi Protected Setup is a feature that makes it easy to set up your wireless network . If you have client devices, such as wireless adapters, that support Wi-Fi Protected Setup, then you can use Wi-Fi Protected Setup .

Configuration View To manually configure your wireless networks, select Manual . Proceed to the Manual  Setup section . To use Wi-Fi Protected Setup, select Wi-Fi Protected Setup . Proceed to Wi-Fi Protected Setup, page 20 .

(23)

Wireless-N Router

Linksys E1000

Chapter 3: Advanced Configuration

Manual Setup

If you set the Configuration  View to Manual, the Basic  Wireless Settings screen displays the following fields .

Wireless > Basic Wireless Settings (Manual Setup)

Network Mode From this drop-down menu, you can select the wireless standards running on your network .

• Mixed If you have Wireless-N, Wireless-G, and Wireless-B devices in your network, keep the default, Mixed .

• BG-Mixed If you have only Wireless-G and Wireless-B devices in your network, select BG-Mixed .

• Wireless-N Only If you have only Wireless-N devices, select Wireless-N Only .

• Wireless-G Only If you have only Wireless-G devices, select Wireless-G Only .

• Wireless-B Only If you have only Wireless-B devices, select Wireless-B Only .

• Disabled If you do not have any wireless devices in your network, select Disabled .

NOTE: If you are not sure which mode to use, keep the default, Mixed .

Network Name (SSID) The Service Set Identifier (SSID) is the network name shared by all devices in a wireless network . It is case-sensitive and must not exceed 32 keyboard characters . The default is Ciscoxxxxx (xxxxx are the last five digits of the Router’s serial number) . The serial number is located on the left side of the product label, which is on the bottom panel .

Channel Width The default is 20 MHz Only . For best performance, select Auto to have the Router automatically select the Channel Width (20 MHz or 40 MHz) .

Channel Select the appropriate channel for your wireless network . If you are not sure which channel to select, then keep the default, Auto .

SSID Broadcast When wireless clients survey the local area for wireless networks to associate with, they will detect the SSID broadcast by the Router . To broadcast the

Router’s SSID, keep the default, Enabled . If you do not want to broadcast the Router’s SSID, then select Disabled . Click Save Settings to apply your changes, or click Cancel Changes to clear your changes .

Wi-Fi Protected Setup

There are three methods available . Use the method that applies to the client device you are configuring .

Wireless > Basic Wireless Settings (Wi-Fi Protected Setup)

NOTE: Wi-Fi Protected Setup configures one client device at a time . Repeat the instructions for each client device that supports Wi-Fi Protected Setup .

• Wi-Fi Protected Setup Button Use this method if your client device has a Wi-Fi Protected Setup button . a . Click or press the Wi-Fi Protected Setup button on

the client device .

b . Click the Wi-Fi Protected Setup button on the Router’s Wi-Fi Protected Setup screen .

The Wi-Fi Protected Setup LED flashes blue for two minutes during the Wi-Fi Protected Setup process and lights up blue when the Wi-Fi Protected Setup process is successful .

The LED lights up amber if there is an error during the Wi-Fi Protected Setup process . Make sure the client device supports Wi-Fi Protected Setup . Wait until the LED is off, and then try again .

The LED flashes when a Wi-Fi Protected Setup session is active . The Router supports one session at a time . Wait until the LED is continuously lit, or off before starting the next Wi-Fi Protected Setup session .

c . After the client device has been configured, click OK on the Router’s Wi-Fi  Protected  Setup

screen . Then refer back to your client device or its documentation for further instructions .

(24)

• Enter Client Device PIN on Router Use this method if your client device has a Wi-Fi Protected Setup PIN (Personal Identification Number) .

a . Enter the PIN from the client device in the field on the Router’s Wi-Fi Protected Setup screen .

b . Click the Register button on the Router’s Wi-Fi  Protected Setup screen .

c . After the client device has been configured, click OK on the Router’s Wi-Fi  Protected  Setup

• Enter Router PIN on Client Device Use this method if your client device asks for the Router’s PIN .

a . On the client device, enter the PIN listed on the Router’s Wi-Fi  Protected  Setup screen . (It is also listed on the label on the bottom of the Router .) b . After the client device has been configured,

click OK on the Router’s Wi-Fi  Protected  Setup

The Network Name (SSID), Security, and Passphrase are displayed at the bottom of the screen .

NOTE: If you have client devices that do not support Wi-Fi Protected Setup, note the wireless settings, and then manually configure those client devices .

Wireless > Wireless Security

The wireless security settings configure the security of your wireless network(s) . The Router supports the following wireless security options: WPA/WPA2 Mixed Mode (default), WPA2 Personal, WPA Personal, WEP, and RADIUS . (WPA stands for Wi-Fi Protected Access . WEP stands for Wireless Equivalent Privacy . RADIUS stands for Remote Authentication Dial-In User Service .)

The default option is WPA/WPA2 mixed mode, which allows your devices to connect using the strongest security option they support, WPA2 or WPA .

Personal Options

Security Option Strength

WPA2 Personal Strongest

WPA/WPA2 mixed mode (default) WPA2: Strongest

WPA: Strong

WPA Personal Strong

WEP Basic

Office Option

RADIUS is the security option offered for networks that use a RADIUS server for authentication .

Security Mode

Select the security method for your wireless network . If you do not want to use wireless security, keep the default, Disabled .

WPA/WPA2 Mixed Mode

NOTE: If you are using WPA/WPA2 mixed mode, each device in your wireless network MUST use the same WPA shared key, or else the network will not function properly .

Wireless Security > WPA/WPA2 Mixed Mode

Passphrase Enter a passphrase of 8-63 characters . The default is password .

WPA2 Personal

NOTE: If you are using WPA2 or WPA, each device in your wireless network MUST use the same WPA method and shared key, or else the network will not function properly .

Wireless Security > WPA2 Personal

(25)

Wireless-N Router

Linksys E1000

Chapter 3: Advanced Configuration

WPA Personal

NOTE: If you are using WPA2 or WPA, each device in your wireless network MUST use the same WPA method and shared key, or else the network will not function properly .

Wireless Security > WPA Personal

WEP

WEP is a basic encryption method, which is not as secure as WPA .

NOTE: If you are using WEP encryption, each device in your wireless network MUST use the same WEP encryption method and encryption key, or else your wireless network will not function properly .

Wireless Security > WEP

Encryption Select a level of WEP encryption, 40/64 bits (10 hex digits) or 104/128 bits (26 hex digits) . The default is 40/64 bits (10 hex digits) .

Passphrase Enter a Passphrase to automatically generate WEP keys . Then click Generate .

Key 1 If you did not enter a Passphrase, enter the WEP key manually .

RADIUS

This option features WEP used in coordination with a RADIUS server . (This should only be used when a RADIUS server is connected to the Router .)

NOTE: If you are using WEP encryption, each device in your wireless network MUST use the same WEP encryption method and encryption key, or else your wireless network will not function properly .

RADIUS

RADIUS Server Enter the IP address of the RADIUS server .

RADIUS Port Enter the port number of the RADIUS server . The default is 1812 .

Shared Secret Enter the key shared between the Router and the server .

Encryption Select a level of WEP encryption, 40/64 bits (10 hex digits) or 104/128 bits (26 hex digits) . The default is 40/64 bits (10 hex digits) .

Passphrase Enter a Passphrase to automatically generate WEP keys . Then click Generate .

Key 1 If you did not enter a Passphrase, enter the WEP key manually .

(26)

Wireless > Wireless MAC Filter

Wireless access can be filtered (restricted) by specifying the MAC addresses of the devices in your wireless network .

Wireless > Wireless MAC Filter

Wireless MAC Filter

Enabled/Disabled To filter wireless users by the MAC addresses of their computers or devices, select Enabled . Otherwise, keep the default, Disabled .

Access Restriction

Prevent PCs listed below from accessing the wireless network Select this option to block wireless access by MAC address . This option is enabled by default .

Permit PCs listed below access to the wireless network Select this option to allow wireless access by MAC address . This option is disabled by default .

MAC Address Filter List

Wireless Client List Click this option to open the Wireless  Client List screen .

Wireless Client List

This screen shows computers and other devices on the wireless network . The list can be sorted by Client Name, Interface, IP Address, MAC Address, and Status . Select Save to MAC Address Filter List for any device you want to add to the MAC Address Filter List . Then click Add .

To update the on-screen information, click Refresh . To exit this screen and return to the Wireless MAC Filter

screen, click Close .

MAC 01-50 Enter the MAC addresses of the devices whose wireless access you want to control .

(27)

Wireless-N Router

Linksys E1000

Chapter 3: Advanced Configuration

Wireless > Advanced Wireless Settings

The Advanced  Wireless  Settings screen is used to set up the Router’s advanced wireless functions . These settings should only be adjusted by an advanced user because incorrect settings can reduce wireless performance . In most cases, keep the default settings .

Wireless > Advanced Wireless Settings

Advanced Wireless

AP Isolation The AP (Access Point) Isolation feature isolates all wireless clients and wireless devices on your network from each other . Wireless devices will be able to communicate with the Router but not with each other . To use this option, select Enabled . AP Isolation is disabled by default .

Frame Burst This option should provide your network with greater performance, depending on the manufacturer of your wireless products . To use this option, keep the default, Enabled . Otherwise, select Disabled .

Authentication Type The Authentication Type setting is available if the Security Mode is RADIUS or WEP . The default is set to Auto, which allows either Open System or Shared Key authentication to be used . With Open System authentication, the sender and the recipient do NOT use a WEP key for authentication . With Shared Key authentication, the sender and recipient use a WEP key for authentication . Select Shared Key to only use Shared Key authentication .

Basic Rate The Basic Rate setting is not actually one rate of transmission but a series of rates at which the Router can transmit . (The Basic Rate is not the actual rate of data transmission . If you want to specify the Router’s rate of data transmission, configure the Transmission Rate setting .) The Router will advertise its Basic Rate to the other wireless devices in your network, so they know which rates will be used . The Router will also advertise that it will automatically select the best rate for transmission . The default setting is Default, when the Router can transmit at all standard wireless rates (1-2 Mbps, 5 .5 Mbps,

11 Mbps, 18 Mbps, and 24 Mbps) . Select 1-2 Mbps for use with older wireless technology . Select All, when the Router can transmit at all wireless rates .

Transmission Rate The Transmission setting is available if the Network Mode is BG-Mixed, Wireless-G Only, or Wireless-B Only . The rate of data transmission should be set depending on the speed of your wireless network . Select from a range of transmission speeds, or keep the default, Auto, to have the Router automatically use the fastest possible data rate and enable the Auto-Fallback feature . Auto-Fallback will negotiate the best possible connection speed between the Router and a wireless client .

N Transmission Rate The N Transmission setting is available if the Network Mode is Mixed or Wireless-N Only . The rate of data transmission should be set depending on the speed of your Wireless-N networking . Select from a range of transmission speeds, or keep the default, Auto, to have the Router automatically use the fastest possible data rate and enable the Auto-Fallback feature . Auto-Fallback will negotiate the best possible connection speed between the Router and a wireless client .

CTS Protection Mode The Router automatically uses CTS (Clear-To-Send) Protection Mode when your Wireless-N and Wireless-G devices are experiencing severe problems and are not able to transmit to the Router in an environment with heavy 802 .11b traffic . This option boosts the Router’s ability to catch all Wireless-N and Wireless-G transmissions but severely decreases performance . To use this option, keep the default, Auto . To disable this option, select Disabled .

Beacon Interval A beacon is a packet broadcast by the Router to synchronize the wireless network . The Beacon Interval value indicates the frequency interval of the beacon . Enter a value between 20 and 65,535 milliseconds . The default value is 100 .

DTIM Interval This value, between 1 and 255, indicates the interval of the Delivery Traffic Indication Message (DTIM) . A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages . When the Router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value . Its clients hear the beacons and awaken to receive the broadcast and multicast messages . The default value is 1 .

Fragmentation Threshold This value specifies the maximum size for a packet before data is fragmented into multiple packets . If you experience a high packet error rate, you may slightly increase the Fragmentation Threshold . Setting the Fragmentation Threshold too low may result in poor network performance . Only minor reduction of the default value is recommended . In most cases, it should remain at its default value of 2346 .

User Guide. Linksys E1000. Wireless-N Router

Linksys E1000

Wireless-N Router

Contents

Linksys E1000

Table of Contents

Chapter 1: Product Overview

Top

Back

Horizontal Placement

Linksys E1000

Chapter 1: Product Overview

Wall-Mounting Placement

152 mm

Chapter 2: Cisco Connect

Installation

Linksys E1000

Chapter 2: Cisco Connect

Main Menu

Local Access versus Guest Access

Main Menu – Computers and Devices

Main Menu – Parental Controls

Main Menu – Guest Access

Main Menu – Router Settings

Linksys E1000

Chapter 2: Cisco Connect

Computers and Other Devices

Computer

Connect with the Easy Setup Key

Create or Update the Easy Setup Key

Connect Manually

Wireless Printer

Linksys E1000

Chapter 2: Cisco Connect

Parental Controls

First-Time Access of Parental Controls

Restrict Internet Access List

Set Up Parental Controls

Linksys E1000

Chapter 2: Cisco Connect

Change Parental Controls Password

Guest Access

Router Settings

Personalize

Easy Setup Key

Other Options

Change Router Name or Password

Router Details

Linksys E1000

Chapter 2: Cisco Connect

Advanced Settings

How to Exit Cisco Connect

How to Access Cisco Connect

Windows

Mac

Chapter 3: Advanced Configuration

How to Access the Browser-Based Utility

Setup > Basic Setup

Language

Internet Setup

Internet Connection Type

Linksys E1000

Chapter 3: Advanced Configuration

Linksys E1000

Chapter 3: Advanced Configuration

Optional Settings

Network Setup

Router IP

DHCP Server Settings

Time Settings

Setup > DDNS

DDNS

DDNS Service

Linksys E1000

Chapter 3: Advanced Configuration

Setup > MAC Address Clone

MAC Address Clone

Setup > Advanced Routing

Advanced Routing

NAT