SERVICES
GUIDE
For more information and the latest
Terms and Conditions of Service, visit StraightTalk.com
Remote Alert System
PLEASE RECYCLE QUAG-STAX54NC
® ®
LoCAtE thE ACtIVAtIoN CARD
INSIDE YoUR PACkAGE FIRSt
START HERE
ACTIVATION AND SETUP 1. ACTIVATE YOUR SERVICE
1. Go to StraightTalk.com or call 1-888-251-8165.
2. Select the Activate option.
3. Provide the device’s Serial Number (MEID DEC) displayed below.
4. Use your Straight Talk Remote Alert Service Plan, or purchase one using a credit or debit card.
3. PROGRAM YOUR CONTROLLER UNIT A. Activation Programming
1. Using the keypad on the Controller Unit, press will initiate the programming. This may take a couple of minutes. *228 Func. This 2. The zone LEDs will blink red during programming. Once the programming is complete, the zone LEDs will turn solid green. If the zone LEDs turn solid red, wait fi ve minutes and press
*228 Func again.
B. Confi gure CALL Alerts
The device can be confi gured to CALL up to 5 diff erent phone numbers when a sensor is triggered.
1. Access the programming mode by entering Func password
Func. The default password for your device is 1234. The fi ve LEDs
in the top row will turn solid green during programming mode.
2. To add the fi rst phone number for your device to CALL, press
Func 51 Func ten digit phone number * ten digit phone number Func. 3. To add additional phone numbers replace the 5or 5* . For example: 5ten digit phone numberFunc 52 Func Func ten digit phone number.1 with 5, 523, 54,
C. Confi gure TEXT MESSAGE Alerts
The device can be confi gured to send a TEXT MESSAGE to up to 3 diff erent phone numbers when a sensor is triggered. 1. Access the programming mode by entering Func. The default password for your device is Func1234 password. The fi ve LEDs in
the top row will turn solid green during programming mode.
2. To add the fi rst phone number that the device will send a TEXT MESSAGE to, press Func 31 Func ten digit phone number
*
ten digit phone number Func. 3. To add the additional phone numbers replace the 3For example Func 32 Func ten digit phone number 1 with 32 or 3* 3.
ten digit phone number Func.
4. TEST THE REMOTE ALERT SYSTEM
1. Arm your Remote Alert System by pressing the Controller Unit. Away key on the
2. Wait 30 seconds (default exit delay) and then trigger your Motion Sensor by waving at it.
3. After 30 seconds (default entry delay) the Controller Unit should trigger a continuous beep.
4. Confi rm that you receive the CALL and/or TEXT MESSAGE alert (depending on what you setup).
5. Disarm the Remote Alert System by entering your password on the
Controller Unit. The default password for your device is 1234.
5. ARM / DISARM A. Arm/Disarm your System from the Controller Unit Armed Away Mode*: In the Armed Away Mode, when a sensor is triggered the Remote Alert System will emit a continuous beep for 4 minutes.
1. Press the Away key on the Controller Unit.
2. Disarm the system by entering your password on the Controller Unit. The default password for your device is 1234.
Armed Away Silent Mode*sensor is triggered, your system will not emit a continuous beep, so the intruder will be unaware that the sensor was triggered. However, alerts will : In the Armed Away Silent Mode, when a be sent to the designated phones.
1. Press the 1 Away key on the Controller Unit.
2. Disarm the system by entering your password on the Controller Unit.
The default password for your device is 1234.
* Additional Arming options can be found in the Services Guide that came in your package.
B. Arm/Disarm your System from your smartphone
You can download the free Straight Talk Home Alert* mobile
application from the Google Play™ Store or the App Store. This application enables you to arm and disarm your Remote Alert System from your Android™ or iPhone.
You will need your Remote Alert System phone number to set up the
application. To fi nd this phone number, confi gure a text or call alert (see Section 3), then trigger a sensor (see Section 4). Your Remote Alert System phone number will appear in the text message log or call log from the phone that receives the alert.
*This app works on phones powered by Android™ and all iPhones.
6. CHANGE YOUR DEFAULT PASSWORD (OPTIONAL)
1. Access the programming mode by entering Func password Func.
The default password for your device is 1234.
2. Press Func 00 Func new password * new password
Func.
3. Be sure to remember or note your new password for future use.
7. MOUNT THE REMOTE ALERT SYSTEM
Mount or place your Controller Unit and Motion Sensors in convenient locations. Note that your Motion Sensor is already paired to the Controller Unit. Please see the Services Guide enclosed in your package for detailed instructions on how to wall-mount the Controller Unit and Motion Sensor.
2. SET UP YOUR REMOTE ALERT SYSTEM
1. Install the batteries in both devices .
2. Turn ON the Controller Unit by connecting it to the power cord
included in your package. Plug it in to an electrical outlet.
3. Turn ON the Motion Sensor by installing the battery.
Do not rely on the Controller Unit battery as the only power source since it will drain in approximately one week.
®
PLEASE READ THE TERMS AND CONDITIONS OF SERVICE IN THE SERVICES GUIDE IN THIS PACKAGE or at StraightTalk.com BEFORE ACTIVATING YOUR DEVICE OR ANY SERVICE PLANS.
ACARD-STAX54NC
1
.
Get
Started
3
.
How To Use
Your Remote
Alert System
2
.
About Your
Straight Talk
Wireless Service
ThANk YoU foR bUYiNG A STRAiGhT TALk
wiRELESS REMoTE ALERT SYSTEM!
YoU MAdE ThE RiGhT ChoiCE.
CoNTRoLLER UNiT
CoNTRoLLER UNiT
1. PowER LEd iNdiCAToR
2. bATTERY LEd iNdiCAToR
3. SiGNAL LEd iNdiCAToR
4. SETTiNG/REGiSTER LEd iNdiCAToR
5. ACTiVE LEd iNdiCAToR
6. ZoNE 1 LEd iNdiCAToR
7. ZoNE 2 LEd iNdiCAToR
8. ZoNE 3 LEd iNdiCAToR
9. ZoNE 4 LEd iNdiCAToR
10. AwAY:
Press to activate or deactivate the different Armed Modes
11. STAY:
Press to activate the Armed Stay Mode
12. PANiC:
Press to immediately activate the alert. Sends SMS and phone
call alert to numbers you have programmed to receive alerts.
13. fUNC bUTToN:
Press to begin a programming sequence on your
Remote Alert System.
14. kEYPAd
MoTioN SENSoR
15. MoTioN SENSoR: PowER LEd iNdiCAToR
16.
MoTioN SENSoR: ViSoR
1
2
3
4
5
6
7 8
9
14
10 1112 13
16
15
For an interactive tutorial of your Remote Alert System, please visit
StraightTalk.com
. Hold your cursor over
Support
. Select
Manuals
.
Select your device model and click on
LEARN
MoRE
.
LEd PRoGRAM ModE GREENSoLid bLiNkiNG GREEN SoLid REd bLiNkiNG REd off PowER Solid green when in Programming Mode
Device is ON - - - Device is OFF
bATTERY Device is ON - Power lowBattery
-No Battery is installed or the device is running on AC power.
SiGNAL Connected to network; good signal Connected; signal is weak - - No network signal SETTiNG / REGiSTER In process of setting alert In register status - -Not in Setting/ Registering Mode
ACTiVE - - - Alert is Armed - DisarmedAlert is
ZoNES 1- 4 - Armed Programming Success DetectedAlert Programming Fail Disarmed
ZoNES 1- 4 - Activation Success - Activation Fail -
-UNdERSTANdiNG ThE iNdiCAToRS
The table below describes possible states for each of the device indicators.
TAbLE of CoNTENTS
1.
GET STARTEd
1.1
What’s In Your Package
1.2
Activate Your Straight Talk Wireless Service
1.3
Set Up Your Straight Talk Wireless Account
2.
AboUT YoUR STRAiGhT TALk wiRELESS SERViCE
2.1
Keep Your Service Active
2.2
Know Your Service Plans and Refill Options
3.
how To USE YoUR STRAiGhT TALk wiRELESS
REMoTE ALERT SYSTEM
3.1
Find Your Serial Number
3.2
Set up your Remote Alert System
3.3
Activation Programming
3.4
Access Programming Mode and Default Password
3.5
Change your Password
3.6
Set up Text Message Alerts
3.7
Set up Call Alerts
3.8
Arm the Remote Alert System
3.9
Disarm the Remote Alert System
3.10
Adjust Exit and Entry Delay Time
3.11
Arm/Disarm Confirmation Text Message Settings
3.12
Test SMS or Phone Calls
3.13
Add or Remove Sensors
3.14
Mount the Remote Alert System
3.15
Accessories Available
3.16
Restore the Remote Alert System to Factory Settings
What’s In Your Package
Activate Your Straight Talk Wireless Service
Set Up Your Straight Talk Wireless Account
1.1
1.2
1.3
1
.
Get
Started
1.1
whAT’S iN YoUR PACkAGE
9V batteries Activation Card Mounting
bracket
Services Guide
START HERE
ACTIVATION AND SETUP 1. ACTIVATE YOUR SERVICE
1. Go to StraightTalk.com or call 1-888-251-8165.
2. Select the Activate option.
3. Provide the device’s Serial Number (MEID DEC) displayed below.
4. Use your Straight Talk Remote Alert Service Plan, or purchase one using a credit or debit card.
3. PROGRAM YOUR CONTROLLER UNIT A. Activation Programming
1. Using the keypad on the Controller Unit, press *228 Func. This
will initiate the programming. This may take a couple of minutes. 2. The zone LEDs will blink red during programming. Once the
programming is complete, the zone LEDs will turn solid green. If the zone LEDs turn solid red, wait fi ve minutes and press
*228 Func again.
B. Confi gure CALL Alerts
The device can be confi gured to CALL up to 5 diff erent phone numbers
when a sensor is triggered.
1. Access the programming mode by entering Func password
Func. The default password for your device is 1234. The fi ve LEDs
in the top row will turn solid green during programming mode.
2. To add the fi rst phone number for your device to CALL, press
Func 51 Func ten digit phone number * ten digit phone number Func.
3. To add additional phone numbers replace the 51 with 52, 53, 54,
or 55. For example: Func 52 Func ten digit phone number
* ten digit phone number Func.
C. Confi gure TEXT MESSAGE Alerts
The device can be confi gured to send a TEXT MESSAGE to up to 3
diff erent phone numbers when a sensor is triggered.
1. Access the programming mode by entering Func password
Func. The default password for your device is 1234. The fi ve LEDs in
the top row will turn solid green during programming mode. 2. To add the fi rst phone number that the device will send a TEXT
MESSAGE to, press Func 31 Func ten digit phone number
* ten digit phone number Func.
3. To add the additional phone numbers replace the 31 with 32 or 33.
For example Func 32 Func ten digit phone number *
ten digit phone number Func.
4. TEST THE REMOTE ALERT SYSTEM
1. Arm your Remote Alert System by pressing the Away key on the
Controller Unit. 2. Wait 30 seconds (default exit delay) and then trigger your Motion
Sensor by waving at it. 3. After 30 seconds (default entry delay) the Controller Unit should trigger
a continuous beep. 4. Confi rm that you receive the CALL and/or TEXT MESSAGE alert
(depending on what you setup). 5. Disarm the Remote Alert System by entering your password on the
Controller Unit. The default password for your device is 1234.
5. ARM / DISARM A. Arm/Disarm your System from the Controller Unit
Armed Away Mode*: In the Armed Away Mode, when a sensor is triggered the Remote Alert System will emit a continuous beep for 4 minutes.
1. Press the Away key on the Controller Unit.
2. Disarm the system by entering your password on the Controller Unit.
The default password for your device is 1234.
Armed Away Silent Mode*: In the Armed Away Silent Mode, when a sensor is triggered, your system will not emit a continuous beep, so the intruder will be unaware that the sensor was triggered. However, alerts will be sent to the designated phones.
1. Press the 1 Away key on the Controller Unit.
2. Disarm the system by entering your password on the Controller Unit.
The default password for your device is 1234.
* Additional Arming options can be found in the Services Guide that came
in your package.
B. Arm/Disarm your System from your smartphone
You can download the free Straight Talk Home Alert* mobile
application from the Google Play™ Store or the App Store. This application enables you to arm and disarm your Remote Alert System from your Android™ or iPhone.
You will need your Remote Alert System phone number to set up the
application. To fi nd this phone number, confi gure a text or call alert (see Section 3), then trigger a sensor (see Section 4). Your Remote Alert System phone number will appear in the text message log or call log from the phone that receives the alert.
*This app works on phones powered by Android™ and all iPhones.
6. CHANGE YOUR DEFAULT PASSWORD (OPTIONAL)
1. Access the programming mode by entering Func password Func.
The default password for your device is 1234.
2. Press Func 00 Func new password * new password
Func.
3. Be sure to remember or note your new password for future use.
7. MOUNT THE REMOTE ALERT SYSTEM
Mount or place your Controller Unit and Motion Sensors in convenient
locations. Note that your Motion Sensor is already paired to the Controller Unit. Please see the Services Guide enclosed in your package for detailed instructions on how to wall-mount the Controller Unit and Motion Sensor.
2. SET UP YOUR REMOTE ALERT SYSTEM
1. Install the batteries in both devices .
2. Turn ON the Controller Unit by connecting it to the power cord
included in your package. Plug it in to an electrical outlet.
3. Turn ON the Motion Sensor by installing the battery.
Do not rely on the Controller Unit battery as the only power source since it will drain in approximately one week.
®
PLEASE READ THE TERMS AND CONDITIONS OF SERVICE IN THE SERVICES GUIDE IN THIS PACKAGE or at StraightTalk.com BEFORE ACTIVATING YOUR DEVICE OR ANY SERVICE PLANS.
ACARD-STAX54NC
SERVICES GUIDE
For more information and the latest Terms and Conditions of Service, visit StraightTalk.com
Remote Alert System
PLEASE RECYCLE QUAG-STAX54NC ®
LOCATE THE ACTIVATION CARD INSIDE YOUR PACKAGE FIRST
START HERE
ACTIVATION AND SETUP 1. ACTIVATE YOUR SERVICE
1. Go to StraightTalk.com or call 1-888-251-8165. 2. Select the Activate option. 3. Provide the device’s Serial Number (MEID DEC) displayed below. 4. Use your Straight Talk Remote Alert Service Plan, or purchase one using a credit or debit card.
2. SETUP YOUR REMOTE ALERT SYSTEM
1. Install the batteries in both devices . 2.
Turn ON the Controller Unit by connecting it to the power cord included in your package. Plug it in to an electrical outlet.
3.
Turn ON the Motion Sensor by installing the battery. Do not rely on the Controller Unit battery as the only power source since it will drain in approximately one week.
®
PLEASE READ THE TERMS AND CONDITIONS OF SERVICE IN THE SERVICES GUIDE IN THIS PACKAGE or at StraightTalk.com BEFORE ACTIVATING YOUR PHONE OR ANY SERVICE PLANS. ACARD-STAX54
1.
Get Started
3.
How To Use Your Straight Talk Wireless Remote Alert System 2. About Your Straight Talk Wireless Service Screws Motion Sensor Remote Alert Control Unit Charger
1.2
ACTiVATE YoUR
STRAiGhT TALk wiRELESS SERViCE
START HERE
ACTIVATION AND SETUP 1. ACTIVATE YOUR SERVICE
1. Go to StraightTalk.com or call 1-888-251-8165. 2. Select the Activate option. 3. Provide the device’s Serial Number (MEID DEC) displayed below. 4. Use your Straight Talk Remote Alert Service Plan, or purchase one
using a credit or debit card.
3. PROGRAM YOUR CONTROLLER UNIT A. Activation Programming
1. Using the keypad on the Controller Unit, press *228 Func. This will initiate the programming. This may take a couple of minutes. 2. The zone LEDs will blink red during programming. Once the
programming is complete, the zone LEDs will turn solid green. If the zone LEDs turn solid red, wait fi ve minutes and press
*228 Func again.
B. Confi gure CALL Alerts
The device can be confi gured to CALL up to 5 diff erent phone numbers when a sensor is triggered. 1. Access the programming mode by entering Func password
Func. The default password for your device is 1234. The fi ve LEDs in the top row will turn solid green during programming mode. 2. To add the fi rst phone number for your device to CALL, press
Func 51 Func ten digit phone number * ten digit phone number Func. 3. To add additional phone numbers replace the 51 with 52, 53, 54,
or 55. For example: Func 52 Func ten digit phone number
* ten digit phone number Func.
C. Confi gure TEXT MESSAGE Alerts
The device can be confi gured to send a TEXT MESSAGE to up to 3 diff erent phone numbers when a sensor is triggered. 1. Access the programming mode by entering Func password
Func. The default password for your device is 1234. The fi ve LEDs in the top row will turn solid green during programming mode. 2. To add the fi rst phone number that the device will send a TEXT MESSAGE to, press Func 31 Func ten digit phone number
* ten digit phone number Func. 3. To add the additional phone numbers replace the 31 with 32 or 33.
For example Func 32 Func ten digit phone number *
ten digit phone number Func.
4. TEST THE REMOTE ALERT SYSTEM
1. Arm your Remote Alert System by pressing the Away key on the Controller Unit. 2. Wait 30 seconds (default exit delay) and then trigger your Motion
Sensor by waving at it. 3. After 30 seconds (default entry delay) the Controller Unit should trigger
a continuous beep. 4. Confi rm that you receive the CALL and/or TEXT MESSAGE alert
(depending on what you setup). 5. Disarm the Remote Alert System by entering your password on the
Controller Unit. The default password for your device is 1234. 5. ARM / DISARM
A. Arm/Disarm your System from the Controller Unit Armed Away Mode*: In the Armed Away Mode, when a sensor is triggered the Remote Alert System will emit a continuous beep for 4 minutes. 1. Press the Away key on the Controller Unit. 2. Disarm the system by entering your password on the Controller Unit.
The default password for your device is 1234. Armed Away Silent Mode*: In the Armed Away Silent Mode, when a
sensor is triggered, your system will not emit a continuous beep, so the intruder will be unaware that the sensor was triggered. However, alerts will be sent to the designated phones. 1. Press the 1 Away key on the Controller Unit. 2. Disarm the system by entering your password on the Controller Unit.
The default password for your device is 1234.
* Additional Arming options can be found in the Services Guide that came
in your package.
B. Arm/Disarm your System from your smartphone
You can download the free Straight Talk Home Alert* mobile application from the Google Play™ Store or the App Store. This application enables you to arm and disarm your Remote Alert System from your Android™ or iPhone. You will need your Remote Alert System phone number to set up the
application. To fi nd this phone number, confi gure a text or call alert (see Section 3), then trigger a sensor (see Section 4). Your Remote Alert System phone number will appear in the text message log or call log from the phone that receives the alert.
*This app works on phones powered by Android™ and all iPhones.
6. CHANGE YOUR DEFAULT PASSWORD (OPTIONAL)
1. Access the programming mode by entering Func password Func. The default password for your device is 1234. 2. Press Func 00 Func new password * new password
Func. 3. Be sure to remember or note your new password for future use.
7. MOUNT THE REMOTE ALERT SYSTEM
Mount or place your Controller Unit and Motion Sensors in convenient locations. Note that your Motion Sensor is already paired to the Controller Unit. Please see the Services Guide enclosed in your package for detailed instructions on how to wall-mount the Controller Unit and Motion Sensor.
2. SET UP YOUR REMOTE ALERT SYSTEM
1. Install the batteries in both devices . 2. Turn ON the Controller Unit by connecting it to the power cord
included in your package. Plug it in to an electrical outlet. 3. Turn ON the Motion Sensor by installing the battery. Do not rely on the Controller Unit battery as the only power source since it will drain in approximately one week.
®
PLEASE READ THE TERMS AND CONDITIONS OF SERVICE IN THE SERVICES GUIDE IN THIS PACKAGE or at StraightTalk.com BEFORE ACTIVATING YOUR DEVICE OR ANY SERVICE PLANS.
ACARD-STAX54NC
A
B C
Locate your Activation Card
and follow the instructions on the card.
To activate your Straight Talk Service, go to
StraightTalk.com
, select
Activate/Reactivate
and follow the instructions. You will need the
information on the red Activation Card in your
package to continue the Activation process.
For additional help, call the Customer Care
Center at 1-888-251-8165.
This card has the serial number (MEid dEC) you
need to Activate your Remote Alert System.
To Activate, go to StraightTalk.com or call 1-888-251-8165.
1.3
SET UP YoUR
STRAiGhT TALk wiRELESS ACCoUNT
My Account can be created upon activation of your Remote Alert System
at StraightTalk.com. This is where you will create and update your personal
profile information, update credit/billing information, view your Service
End Date, and more.
My Account is the best place to:
• Buy or Add a Service Plan
• Enroll in Auto-Refill
• Manage your Straight Talk Reserve™
• Check Service End Date
• See Account Reminders and Service Updates
• Update Personal Profile and Manage Credit Card Info
• View Payment History
• Get Newsletter Access
• Learn how to use your Remote Alert System
• View FAQs
Keep Your Service Active
Know Your Service Plans and Refill Options
2.1
2.2
2
.
About Your
Straight Talk
Wireless Service
keep your Service Active with your choice of Refill Now
or Auto-Refill Service Plan options.
2.1
kEEP YoUR SERViCE ACTiVE
iMPoRTANT!
To keep your Service Active, you must refill your
Service Plan bEfoRE your Service End date.
keeping your Service Active is easy! Just add a Remote Alert Service
Plan before your Service End date!
To find your Service End Date, go
to our website at
StraightTalk.com
and log into My Account or call our
Customer Care Center at
1-888-251-8165.
A
2.2
kNow YoUR SERViCE PLANS
ANd REfiLL oPTioNS
Straight Talk wireless offers the following Service Plans for your
Remote Alert System:
Works With Straight Talk Remote Alert System Only No Value Until
Purchased and Scanned
30-Day Service PlanNo-Contract
Device and plan sold separately
Remote
Alert System
Great for Home, Apartment, RV, Storage Unit or Shed
Works With Straight Talk Remote Alert System Only No Value Until
Purchased and Scanned
1-Year Service PlanNo-Contract
Device and plan sold separately
Remote
Alert System
Great for Home, Apartment, RV, Storage Unit or Shed
30 days
365 days
how to Refill Your Service Plan
•
Enroll in Auto-Refill at StraightTalk.com
by using a credit
card or debit card and your Straight Talk Service Plan will be
automatically refilled on your Service End Date. This service
includes pre-charge reminders, payment receipts and credit
card expiration alerts.
•
Refill your Service Plan before your Service End date
» Online at StraightTalk.com or Walmart.com
» By calling 1-888-251-8165
» Purchase a Remote Alert Service Plan at participating
Walmart stores
Plans added before your Service End Date will be added to your Straight
Talk Reserve and automatically applied on your Service End Date. There
is no limit to the number of Service Plans that can be placed on reserve.
View plans in your reserve by visiting StraightTalk.com and logging into
My Account.
3.1
Find Your Serial Number
3.2
Set up Your Remote Alert System
3.3
Activation Programming
3.4
Access Programming Mode and Default Password
3.5
Change your Password
3.6
Set up Text Message Alerts
3.7
Set up Call Alerts
3.8
Arm the Remote Alert System
3.9
Disarm the Remote Alert System
3.10
Adjust Exit and Entry Delay Time
3.11
Arm / Disarm Confirmation Text Message Settings
3.12
Test SMS or Phone Calls
3.13
Add or Remove Sensors
3.14
Mount the Remote Alert System
3.15
Accessories Available
3.16
Restore the Remote Alert System to Factory Settings
3
.
HOW TO USE YOUR
STRAIGHT TALK WIRELESS
REMOTE ALERT SYSTEM
3.1
fiNd YoUR SERiAL NUMbER
The Serial Number of your Remote Alert System is located on the front of
the Activation Card enclosed in your package. If you do not have access
to the card, you can also locate the Remote Alert Serial Number on the
back of the Controller Unit. It is the number series next to
MEid dEC
.
3.2
SET UP YoUR REMoTE ALERT SYSTEM
1.
Install the batteries in both devices.
2.
Turn
oN
the Controller Unit by connecting it to the power cord
included in your package. Plug the power cord into an electrical outlet.
3.
The
Power
LED on the Controller Unit will turn solid green.
4.
Turn
oN
the Motion Sensor by installing the battery. The LED on the
front of the Motion Sensor will blink slowly.
3.3
ACTiVATioN PRoGRAMMiNG
In order to acquire a network signal as is needed for your Remote Alert
System to function properly, follow these steps AFTER you Activate
the System:
1.
Turn
oN
the Controller Unit by connecting it to the power cord
included in your package. Plug the power cord into an electrical outlet.
2.
Using the keypad of the Controller Unit, press
*
228 func
. This will
initiate the System’s programming. This may take a couple of minutes.
3.
The zone LEDs will blink red during programming. Once programming
is complete, the zone LEDs will turn solid green. If the zone LEDs turn
solid red, wait five minutes and repeat step 2.
3.4
ACCESS PRoGRAMMiNG ModE
ANd dEfAULT PASSwoRd
The default password for your Remote Alert System is 1234.
The Programming Mode
is used to set ALL ALERTS of the Remote Alert
System. To ACCESS the Programming Mode, from the keypad enter:
1.
func
Key
password
func
Key
2.
When the device is in Programming Mode the
Power, battery, Signal
,
and
Setting/Register
LED indicators will all be solid green.
Please note that ALL FUNCTIONS require that you be in
Programming
Mode
to perform them.
Once a sequence has been initiated in the Programming Mode, a 5
second timer will begin. After a key is pressed, if 5 seconds elapse before
another key is pressed, all 4 zone LEDs will blink red 3 times and you will
need to begin the programming sequence again. If 30 seconds elapse
before another key is pressed, the Remote Alert System will exit the
Programming Mode.
When programming is complete, you can exit the Programming Mode by
pressing the
func
key twice. Or, simply wait 30 seconds without pressing
another key and the system will automatically exit the Programming
Mode. All LEDs will return to their normal state.
3.5
ChANGE YoUR PASSwoRd
The default password of your Remote Alert System is 1234.
To change the default password
1.
From the keypad, enter:
func
Key
1234
func
Key (you will enter Programming Mode)
2.
To change the password to
5678 (example only)
enter:
func
Key 00
func
Key 5678
*
5678
func
Key
iT iS AdViSAbLE To ChANGE ThE dEfAULT PASSwoRd
AS SooN AS YoU iNSTALL ANd CoNNECT ThE REMoTE ALERT.
3.6
SET UP TEXT MESSAGE ALERTS
AddiNG SMS NUMbERS
When a sensor is triggered in any zone, you can choose to send an SMS
alert to
up to 3 phone numbers.
SMS numbers can be programmed
into your Remote Alert System following these instructions:
1.
Using the keypad, put the device into Programming Mode
by entering:
func
Key
password
func
Key
2.
Enter the following:
•
SMS #1
: Func Key
31
Func Key ten digit phone number
*
ten digit phone number Func Key
•
SMS #2
: Func Key
32
Func Key ten digit phone number
*
ten digit phone number Func Key
•
SMS #3
: Func Key
33
Func Key ten digit phone number
*
ten digit phone number Func Key
Please note you have to enter the desired phone number
twice
for each
SMS contact. The phone numbers that you enter will need to match.
If you have entered the sequence correctly and both numbers match,
you will hear 2 beeps and all 4 zone LEDs will blink green 1 time. If the
numbers entered do not match, you will hear a long beep and all 4 zone
LEDs will blink red 3 times.
REMoViNG SMS NUMbERS
1.
Using the keypad, put the device into Programming Mode
by entering:
func
Key
password
func
Key
2.
Enter the following:
• Func Key
40
Func Key to
remove all SMS numbers
• Func Key
41
Func Key to remove
SMS #1
• Func Key
42
Func Key to remove
SMS #2
• Func Key
43
Func Key to remove
SMS #3
A
B
3.7
SET UP CALL ALERTS
AddiNG CALL NUMbERS
You can program your Remote Alert System to call
up to 5 phone
numbers
when a sensor is triggered in any zone. When an alert call is
answered, the listener will hear a series of beeps.
1.
Using the keypad put the device into Programming Mode
by entering:
func
Key
password
func
Key
2.
Enter the following:
•
Call #1
: Func Key
51
Func Key ten digit phone number
*
ten digit phone number Func Key
•
Call #2
: Func Key
52
Func Key ten digit phone number
*
ten digit phone number Func Key
•
Call #3
: Func Key
53
Func Key ten digit phone number
*
ten digit phone number Func Key
•
Call #4
: Func Key
54
Func Key ten digit phone number
*
ten digit phone number Func Key
•
Call #5
: Func Key
55
Func Key ten digit phone number
*
ten digit phone number Func Key
Please note you have to enter the desired phone number twice for each
contact you want. The numbers that you enter will need to match. If you
have entered the sequence correctly and both numbers match, you will
hear 2 beeps and all 4 zone LEDs will blink green 1 time. If the numbers
entered
do not
match, there will be a long beep and all 4 zone LEDs will
blink red 3 times
B
After programming SMS and call numbers into your system, it is highly
recommended that you perform a realistic test by arming the device
and tripping a sensor. Check that SMS and calls are received by the
designated phones in order to ensure that the programming was
successfully completed.
REMoViNG CALL NUMbERS
1.
Using the keypad, put the device into Programming Mode
by entering:
func
Key
password
func
Key
2.
Enter the following:
• Func Key
60 func key to remove all Call numbers
• Func Key
61
Func Key to remove
Call #1
• Func Key
62
Func Key to remove
Call #2
• Func Key
63
Func Key to remove
Call #3
3.8
ARM ThE REMoTE ALERT SYSTEM
After the Remote Alert device has been properly installed, the Motion Sensor
has been added, and the SMS/Call numbers have been programmed, it is
ready to be armed. Once in
Armed Mode
, any sensor that is triggered in an
active zone will initiate the alert process.
There are 4 different Armed Modes:
1.
Armed Away
: To activate, press the
Away key
. In the Armed Away
mode, when a sensor is triggered, the Remote Alert System will emit a
continuous beep until it’s been disarmed or re-armed. All programmed
SMS and Call numbers will be sent an alert.
2.
Armed Away Silent
: To activate, press
1
and the
Away key
. The Armed
Away Silent mode provides the same functionality as the Armed Away
mode, EXCEPT that no beep will be emitted if a sensor is triggered. The
intruder will be unaware that the sensor has been triggered, although
SMS/Calls will be sent an alert.
3.
Armed Stay
: To activate, press the
Stay key
. If you want to arm only a
certain part of your house, this can be achieved by using the Armed Stay
mode. In Armed Stay mode, only motion in zone 4 will trigger the alert. If
there is any movement in zones 1, 2 or 3 then the alert will not
be triggered.
In the Armed Stay mode, when a sensor is triggered, the Remote Alert
System will emit a continuous beep for 4 minutes. All programmed SMS
and Call numbers will be sent an alert.
4.
Armed Stay Silent
: To activate, press
1
and the
Stay key
. The Armed Stay
Silent mode provides the same functionality as the Armed Stay mode,
EXCEPT that no beep will be emitted if a sensor is triggered. The intruder
will be unaware that the alert has been triggered, although SMS and Call
numbers will be sent an alert.
Please note zones 1, 2 and 3 will be excluded when using the Armed Stay
Silent mode. Only motion in zone 4 will trigger an alert.
REMoTE ARMiNG
Your Remote Alert System can be armed from your smartphone using
the free
Straight Talk home Alert
1mobile application for Android™ or
iOS phones. You can also arm your system using the
key fob
accessory
(sold separately).
1The app also enables you to remotely manage SMS and call numbers. To download the
application, go to the Google Play™ Store or the App Store and search for Straight Talk.
3.9
diSARM ThE REMoTE ALERT SYSTEM
To DISARM the system, simply enter your password on the Controller
Unit. The amount of time you have to disarm your device is dependent
on the Entry Delay setting. See Section 3.10 B for entry delay time.
REMoTE diSARMiNG
Your Remote Alert System can be disarmed from your smartphone using
the free
Straight Talk home Alert
1mobile application for Android™ or
iOS phones. You can also disarm your system using the
key fob
accessory
(sold separately).
1The app also enables you to remotely manage SMS and call numbers. To download the
3.10
AdJUST EXiT ANd ENTRY dELAY TiME
EXiT dELAY TiME
Your Remote Alert System is already programmed with an Exit Delay. After
you arm the system, the Exit Delay gives you time to exit the premises
without triggering an alert.
The default exit delay is 30 seconds.
To adjust the Exit delay Time
1.
Using the keypad put the device into Programming Mode
by entering:
func
Key
password
func
Key
2.
Enter the following:
• No Exit Delay
2: Func Key
80
Func Key
• 30 Second Exit Delay: Func Key
81
Func Key
• 60 Second Exit Delay: Func Key
82
Func Key
• 90 Second Exit Delay: Func Key
83
Func Key
• 120 Second Exit Delay: Func Key
84
Func Key
2 Although the system can be set for No Exit Delay, this will only be enabled when the Remote
Alert System is armed remotely.
ENTRY dELAY TiME
Your Remote Alert System also has a pre-programmed Entry Delay of 30
seconds. When the system is armed and you trip a sensor by entering
the premises, alerts will not be triggered if the system is disarmed within
30 seconds of entry. This gives you time to get to the control panel and
disarm the system.
B A
A
3.11
ARM / diSARM CoNfiRMATioN
TEXT MESSAGE SETTiNGS
If you have programmed SMS numbers into your Remote Alert device,
those phones will receive an SMS confirmation each time you arm or
disarm the system. This feature is enabled by default.
To diSAbLE CoNfiRMATioN MESSAGES
1.
Using the keypad put the device into Programming Mode
by entering:
func
Key
password
func
Key
2.
Enter the following:
func
Key
39
func
Key (disable sending SMS confirmation)
Once the feature has been disabled, you can enable it at any time.
To adjust the Entry delay Time
1.
Using the keypad put the device into Programming Mode
by entering:
func
Key
password
func
Key
2.
Enter the following:
• No Entry Delay: Func Key
70
Func Key
• 15 Seconds Entry Delay: Func Key
71
Func Key
• 30 Seconds Entry Delay: Func Key
72
Func Key
• 45 Seconds Entry Delay: Func Key
73
Func Key
B
To ENAbLE CoNfiRMATioN MESSAGES
1.
Using the keypad put the device into Programming Mode
by
entering:
func
Key
password
func
Key
2.
Enter the following:
func
Key
38
func
Key (enable sending SMS confirmation)
You cannot disable SMS alerts caused by a sensor being triggered.
3.12
TEST SMS oR PhoNE CALLS
Before starting to use your Remote Alert System you can test it by sending
an SMS or a phone call to any phone number programmed.
•
Test SMS Mode:
This test mode allows your Remote Alert to send an
SMS to any phone number. You must be in the Programming Mode to
perform this function.
Using the keypad, enter:
func
Key
93
func
Key
phone
number
func
Key
•
Test Call Mode:
This test mode allows your Remote Alert to make a
phone call to any phone number. You must be in the Programming
Mode to perform this function.
Using the keypad, enter:
func
Key
92
func
Key
phone
number
func
Key
After programming the SMS and call numbers into your system, it is highly
recommended that you perform a REALISTIC test by arming the device
and tripping a sensor, then checking that SMS and calls were received by
the designated phones. This should be done for each sensor that has been
paired to the device. Remember that when a sensor is tripped, the alerts
will not be sent until the Exit Delay time has elapsed.
3.13
Add oR REMoVE SENSoRS
Add SENSoRS
You can add up to 16 sensors to each one of the 4 zones of your
system for a total of up to 64 Motion Sensors or other Accessories. THE
MOTION SENSOR THAT COMES WITH YOUR REMOTE ALERT SYSTEM IS
ALREADY PAIRED TO THE CONTROLLER UNIT.
To Add more motion sensors or accessories
1.
Using the keypad put the device into Programming Mode by entering:
func
Key
password
func
Key
2.
Enter the following:
• Func Key
11
Func Key trigger the sensor you are adding to Zone 1
• Func Key
12
Func Key trigger the sensor you are adding to Zone 2
• Func Key
13
Func Key trigger the sensor you are adding to Zone 3
• Func Key
14
Func Key trigger the sensor you are adding to Zone 4
The LED for the designated zone will light after entering the initial
commands. To trigger a motion sensor, it must have a battery installed.
Once the battery is installed, simply wave your hand in front of the
motion sensor. You need to trigger the sensor within 30 seconds so that
it registers correctly within the desired zone.
If the sensor has been added properly, you will hear 2 beeps and all
4 zone LEDs will blink green 1 time. If the sensor has not been added
properly there will be a long beep and all 4 zone LEDs will blink red
3 times.
Additional sensors can be added to any zone by repeating the
instructions above.
B
REMoVE SENSoRS
1.
Using the keypad put the device into Programming Mode
by
entering:
func
Key
password
func
Key
2.
Enter the following:
• Func Key
20
Func Key - to remove sensors in all zones
• Func Key
21
Func Key - to remove sensors in Zone 1
• Func Key
22
Func Key - to remove sensors in Zone 2
• Func Key
23
Func Key - to remove sensors in Zone 3
• Func Key
24
Func Key - to remove sensors in Zone 4
Please note that all sensors in the specific zone you select will be
removed. If sensors have been removed properly you will hear 2 beeps
and all 4 zone LEDs will blink green 1 time. If the procedure has not been
accomplished properly there will be a long beep and all 4 zone LEDs will
blink red 3 times.
3.14
MoUNT ThE REMoTE ALERT SYSTEM
CoNTRoLLER UNiT
The Controller Unit should be placed at a convenient access point of
the house. Before setting it up, be sure to install the 9-volt battery. This
will ensure continuous operation in the event of a power outage. The
Controller Unit should always be plugged in to a wall outlet. Never rely
on battery power alone.
horizontal Placement (Tabletop/shelf):
1.
Place the Remote Alert Controller Unit on a smooth surface with
access to good ventilation.
2.
Leave at least 4 inches of clearance space around the device.
Vertical Placement (wall mount):
important:
Do not mount the unit on a wall until you have activated
your system and verified that the network signal is strong in that location.
The Signal indicator light will be solid green if the signal is strong. If the
light is blinking, it means the signal is weak and you should move the
controller to a different location. Make sure the battery is installed in the
unit so it maintains power as you move it to test different locations in
your home.
You can mount the Remote Alert Controller Unit on a wall using screws
that match the two mounting holes on the back of the unit. Screws
must have a head diameter between 3/16” and 5/16” (5mm – 8mm). For
masonry walls, you may need to use anchors to secure the screws. Simply
follow the steps below:
1.
Fix 2 screws into the wall with 2 13/16” of vertical space between
them. Heads should extend approximately 0.1” from the surface of
the wall.
2.
Hold the Controller Unit so that the mounting holes align with the
screws. Then gently push toward the wall so the screw heads enter the
mounting holes.
3.
Slowly lower the device until the screw heads are securely seated.
4.
Ensure that the unit is stable and secure before you release it.
MoTioN SENSoR
The Motion Sensor included with your Remote Alert System has
already been paired with the Controller Unit. It can be placed on a
shelf or a wall to detect motion within 26 feet. Motion Sensors are a
good choice for rooms with lots of windows.
Vertical Mounting (wall-mount):
1.
Fix the mounting bracket to a wall with the 4 screws provided.
2.
Slide the Motion Sensor onto the mounting bracket.
Do not install Motion Sensors close to magnetic door/window sensors.
Motion Sensor coverage is 120 degrees both vertically and horizontally.
The Motion Sensor has been pre-set for pet sensitivity so that movement
of pets will not trigger the alert.
B
3.15
ACCESSoRiES AVAiLAbLE
Sensors and Accessories
Additional accessories can be added to your Remote Alert System. These
are sold separately.
• Motion Sensors (additional)
• Door/Window Sensor
• Key Fob
For instructions on how to pair an additional Motion Sensor, Door/
Window Sensor and the Key Fob to your Remote Alert System, please
refer to the pairing instructions included in the packaging of the device
you wish to pair.
3.16
RESToRE ThE REMoTE ALERT SYSTEM
To fACToRY SETTiNGS
If your Remote Alert System malfunctions or develops any form of
software fault, it may be necessary to perform a factory reset.
1. Using the keypad put the device into Programming Mode by entering:
func
Key
password
func
Key
2. Enter the following:
func
Key
90
func
Key
After a factory reset is performed you will need to program your SMS/Call
numbers and any other parameters you have changed in your Remote
Alert System again. After the device has been programmed,
you must test
it to ensure that all sensors are responsive and that the device is sending
calls and messages when a sensor is triggered.
For an interactive tutorial of your Remote Alert System, please visit
StraightTalk.com
. Hold your cursor over
Support
. Select
Manuals
.
Select your device and click on
LEARN MoRE
.
For more information and the latest
Terms and Conditions of Service, visit StraightTalk.com
tERmS AND CoNDItIoNS
oF SERVICE
® ®
05/2014
PLEASE READ THESE TERMS AND CONDITIONS (“TERMS”) CAREFULLY. THESE TERMS ARE A LEGALLY BINDING AGREEMENT BETWEEN YOU AND TF WIRELESS AND LIMIT YOUR AVAILABLE REMEDIES AND TF WIRELESS’S LIABILITY. THESE LIMITATIONS ARE AN ESSENTIAL ELEMENT OF THE TERMS AND TF WIRELESS WOULD NOT HAVE ENTERED INTO THESE TERMS AND PROVIDED YOU WITH WIRELESS SERVICE WITHOUT THESE LIMITATIONS. THESE TERMS CONTAIN IMPORTANT INFORMATION ABOUT YOUR LEGAL RIGHTS AND REQUIRE THAT DISPUTES BE RESOLVED THROUGH INDIVIDUAL ARBITRATION INSTEAD OF A JURY TRIAL OR CLASS ACTION. THESE TERMS LIMIT AVAILABLE REMEDIES IN THE EVENT OF A DISPUTE OR LOSS. ANY CHANGES OR MODIFICATIONS TO THESE TERMS WILL BE BINDING UPON YOU ONCE POSTED ON THE PRODUCT WEBSITE FOUND AT WWW.STRAIGHTTALKREMOTEALERT.COM. STRAIGHT TALK REMOTE ALERT IS A BRAND AND WIRELESS SERVICE OF TF WIRELESS PRODUCTS, LLC, A DELAWARE LIMITED LIABILITY COMPANY (“TF WIRELESS”).
By purchasing and/or activating a Straight Talk Remote Alert system, and/or using any Straight Talk Remote Alert wireless service (“Wireless Service”), You, the customer, acknowledge and agree to the following terms and conditions:
1. PARTIES TO THIS AGREEMENT
These Terms are an agreement between You and TF Wireless. You are at least 18 years old and competent to enter into this Agreement. You acknowledge that by purchasing, activating and/or using a Straight Talk Remote Alert system and/or the Wireless Service, You agree to be bound by these terms and conditions.
2. DOCUMENTS INCLUDED IN AGREEMENT
Your Agreement with TF Wireless includes these Terms, TF Wireless’s Privacy Policy available on our website and any other documents referred to in these Terms. You understand that these Terms and our Privacy Policy will change from time to time and You agree that these Terms and the Privacy Policy may be revised periodically by posting a new version of the Terms or Privacy Policy on our website. TF Wireless may need to contact you regarding your System or Wireless Service from time to time. By entering into this Agreement, you consent to receive emails at any email address you provide and you agree that we may call you or send a text message to any phone numbers you supply. You agree that our calls to you may be made using any method including autodialing equipment, an artificial or recorded voice, or via text or email messages to a wireless phone. You are responsible for any applicable charges that may be imposed by your wireless provider. You agree when you provide us with a wireless phone number that we are authorized to send you related text messages and questions.
3. REMOTE ALERT SYSTEM
Remote Alert System: The Remote Alert System (“System”) is standalone, non-monitored, and consists of a controller with a built-in wireless module and various sensors that are paired with the controller. When a sensor is triggered, the System can use the Wireless Service to send an SMS message or place a call to a limited number of pre-designated telephone numbers. By programming the System with your phone number, you can receive a SMS message or call when a sensor is triggered. The System is not an alarm, security system or a substitute for a monitored alarm security system.
System Kit: Your basic System kit includes a controller, one motion sensor, a wall power supply, and two 9V batteries (one for the motion sensor and one for the controller that’s a backup battery). To receive an SMS message alert, you must have a separate phone which is not included in the kit. Additional accessories including motion, magnetic door sensors, and remote key fobs are sold separately. All accessories must be paired with the controller before use or the system will not function. The components in the basic System kit are paired at the factory. You must “pair” any additional purchased accessories with the controller prior to use or the system will not operate.
Wireless Service Plan: The System must be used with a subscription Wireless Service plan. You must purchase a Wireless Service plan to activate the System and to receive 30 days of Wireless Service. Multi-month plans may also be available. You must purchase additional Wireless Service plans every 30 days to maintain active service. If your Wireless Service plan lapses or is deactivated or terminated, you will not receive alert messages. For current Wireless Service plan offers, go to www.straighttalk. com/wps/portal/home/shop/serviceplans/homealert.
Minimum Requirements: The System will require sufficient wireless signal strength wherever positioned within the home and electrical power in order to function properly. The System and Wireless Service may be incompatible with certain types of homes. In order for the Wireless Service to operate as intended, the System must have access to a wireless signal of sufficient strength.
Self-Installation: You must self-install the System and all accessories. You are responsible for your installation and to determine that the System and Wireless Service are operating as intended. You agree that TF Wireless is not liable to you in any manner relating to your installation and use of your System and Wireless Service.
4. IMPORTANT NOTICES AND LIMITATIONS
WARNING: REMOTE ALERT IS NOT MONITORED AND IT IS NOT A SUBSTITUTE FOR A MONITORED ALARM SERVICE. IF YOUR SYSTEM IS TRIGGERED, THE SYSTEM WILL SEND A MESSAGE OR PHONE CALL TO ONE OR MORE TELEPHONE NUMBERS YOU HAVE DESIGNATED. NEITHER TF WIRELESS, NOR ANY OTHER THIRD PARTY, WILL DETECT OR RECEIVE ANY ALERT FROM YOUR SYSTEM. NO ONE WILL CONTACT YOU TO ADVISE YOU OF AN ALERT. POLICE, FIRE RESCUE AND OTHER EMERGENCY RESPONSE OR GOVERNMENT PERSONNEL WILL NOT BE CONTACTED IN THE EVENT YOUR ALERT SYSTEM IS TRIGGERED. IN THE EVENT OF AN ALERT, YOU ARE SOLELY RESPONSIBLE FOR TAKING ANY APPROPRIATE RESPONSE ACTION, SUCH AS CALLING THE POLICE, FIRE RESCUE OR ANY OTHER EMERGENCY RESPONSE OR GOVERNMENT PERSONNEL. YOU UNDERSTAND AND AGREE THAT TF WIRELESS WILL NOT RECEIVE ANY MESSAGE OR SIGNAL IF A SENSOR IS TRIGGERED. YOU ARE RESPONSIBLE FOR MAINTAINING A WIRELESS SERVICE PLAN THAT IS ACTIVE AND HAS NOT LAPSED.TESTING THE SYSTEM REGULARLY AND AFTER ANY STORM, POWER OUTAGE OR NETWORK OUTAGE IN ORDER TO VERIFY THE CONTINUED FUNCTIONING OF THE SYSTEM.
WARNING: DO NOT PROGRAM YOUR SYSTEM TO CONTACT 911 OR GOVERNMENT AGENCIES.
Your System cannot be programmed to call 911. Your System is not intended to and should not be programmed to call any law enforcement, fire rescue, or other government agency. When the System
initiates a call in response to an alert, there is no message or other information communicated on the call only an audible beeping sound. If the System were to, for example, be programmed to call a police line, the dispatcher answering the call will receive no information and cannot respond to the alert or locate your System or home. You should program your System to contact You or another responsible person who will take appropriate action in the event of an alert. Programming the System to contact any law enforcement, fire rescue, or government number in the event of an alert may expose you to liability and is a violation of these Terms. You agree not to program the System to call or message any such government agencies. Doing this is prohibited by law in many jurisdictions. You further agree that TF Wireless is not liable to you in any manner relating to your programming of the System.
WARNING: DO NOT PROGRAM THIS SYSTEM TO CONTACT SOMEONE WITHOUT THEIR KNOWLEDGE AND CONSENT. When the System initiates a call in response to an alert, there is no message or other
information communicated on the call only an audible beeping sound. Programming the System to contact someone without their advance knowledge and consent is a violation of these Terms and Conditions, and may expose you to liability.
YOU UNDERSTAND AND AGREE THAT YOU MAY NOT RECEIVE AN ALERT IN THE EVENT A SENSOR IS TRIGGERED IF THE SYSTEM LOSES POWER FOR ANY REASON, THE SYSTEM DOES NOT HAVE ADEQUATE SIGNAL STRENGTH, IF THE SIGNAL FROM THE SENSOR TO THE SYSTEM OR THE SYSTEM TO THE NETWORK IS INTERRUPTED OR THERE IS ANY POWER OR NETWORK OUTAGE, OR IF YOUR WIRELESS SERVICE PLAN HAS LAPSED OR IS TERMINATED FOR ANY REASON. 5. OTHER RESTRICTIONS ON USE
No Modification. The System and Wireless Service is for use in the United States only. You may not, directly or indirectly, engage in any of the following acts (individually, a “Prohibited Act”, and collectively, “Prohibited Acts”): (i) willfully tamper with the security of any Systems or the Wireless Service; (ii) access data not associated with your account; (iii) log into an unauthorized server or another account without authorization; (iv) attempt to probe, scan or test the vulnerability of any service or to breach the company’s security or authentication measures; (v) willfully render any part of the Systems or Wireless Service unusable; (vi) reverse engineer, de-compile, disassemble or otherwise attempt to discover the source code or underlying ideas or algorithms of any System or Wireless Service; (vii) modify, translate, or create derivative works based on any System or Wireless Service; (viii) use any data or information obtained through the use of the System or Wireless Service for any unlawful purpose or in violation of any applicable law (including, without limitation, data protection and privacy laws); or (ix) attempt to remove the SIM card from your System or to attempt to use it in any other device.
You acknowledge and agree that You will not use your System or the Wireless Service for any unlawful purpose. In the event of any suspected violation of these terms and conditions, TF Wireless may immediately disable your access to the Wireless Service and suspend its provision of such Wireless Service.
6. CUSTOMER RESPONSIBILITIES
It is Your sole responsibility to ensure the System is installed and programmed properly, that all accessories are properly “paired” with the controller, that the System and all accessories have
