Operating Instructions Display, graphic. Numeric language

(1)

(2)

(3)

Numeric language, general ... 1

Display control stalk ... 1

Text strings ... 1 Stop message ... 2 Change language ... 3 Change language ... 3 Menus ... 5 General ... 5

Password protected menus ... 5

Menus available when driving ... 6

Menus when vehicle stationary ... 10

Numerical conversion table ... 18

General ... 18

(4)

(5)

Numeric language, general

The instruction describes how the numeric language is made up and functions. Only the most important menus and messages are described. For more in depth information about the display see “Operating instructions Display, graphic”.

Display control stalk

Manual communication with the display is achieved using the control stalk on the right-hand side of the steering wheel. The following commands are available: 1 “Esc” is used to return to the previous

menu and to cancel a setting /operation. 2 “SELECT” confirms the selected choice

of menu or symbol.

3 “ ” moves the cursor up and is used to set numbers/characters.

4 “∇” moves the cursor up and is used to

set numbers / characters. T3008810

Text strings

Numbers between the symbols “<<” and “>>” symbolise a text string. For information about what the numerical text means, see “Menus” page 5 – 17 or “Numerical conversion table” page 18 – 27.

(6)

2 Numeric language, general

Stop message

Red stop lamp + stop symbol

If the red stop lamp and the stop symbol are displayed the vehicle should be stopped immediately and the engine switched off. The associated numerical text should be read in order to establish where the fault lies. For information about what the numerical text means, see “Menus” page 5 – 17 or “Numerical conversion table” page 18 – 27.

T3014364

T3013624

If the engine is running a warning signal also sounds. It can be acknowledged by pressing Esc, but starts again after 10 seconds. For more in depth information about the messages see “Operating instructions Display, graphic”.

WARNING

The vehicle must be stopped immediately and the engine must be turned off when this lamp lights up.

Information lamp CHECK + text

When the information lamp CHECK lights up, the fault should be checked at the next stop. The associated numerical text is shown in the display. A result of measurement is also shown for some symbols. For information about what the numerical text means, see “Menus” page 5 – 17 or “Numerical conversion table” page 18 – 27.

(7)

Change language

The numerical language is a choice and can be shown as one of three languages in the display. The language can be changed in menu “Display settings”.

(8)

4 Change language

Language

MENU: Display setting, Language

The language settings apply even after the ignition has been switched off.

1 Select “Language” with /∇and press on SET. Display settings Language Units Time/date Display lighting Change password CC 7658.8 km

2 Up to three languages can be displayed. Mark “Numerical”, which indicates the numeric language, using /∇and press SELECT. Press Esc to exit settings and return to the Main menu.

(9)

General

The numerical language has a hierarchical structure and follows the same structure as in “Driver instruction Display, graphic”. In those menus which have text, the text is marked with numbers. The menu explanation gives all menu headings and associated text strings.

Password protected menus

The key symbol to the right in the menu list means that the menu is password protected. For more in depth information about the passwords see “Operating instructions Display, graphic”.

(10)

6 Menus

Menus available when driving

Menu 1

<<100>> = Gauge External temperature Temperature, engine oil Temperature, gearbox Volt meter/ Ammeter Gear selection

Pressure, primary tank

Menu 2

<<101>> = Fuel data Fuel consumption

Resetting, fuel data

<<400>> = Reset ALL fuel data? Press SELECT for 1 second.

Leg fuel

Resetting, fuel data

<<400>> = Reset ALL fuel data? Press SELECT for 1 second.

(11)

Menu 3

<<102>> = Time/distance Trip meter

Reset the tripmeter

<<403>> = Reset? Press SELECT for 1 second.

Average speed

Reset average speed

<<403>> = Reset? Press SELECT for 1 second.

Estimated time of arrival

Give distance to destination <<405>> = Give distance:

Time and date

Setting, time and date

Alarm clock

Setting, alarm clock <<301>> = ON <<302>> = OFF <<303>> = NEW TIME

Menu 4

<<103>> = Display <<304>> = Black panel <<306>> = Background lighting

Setting, background lighting

<<307>> = Favourite Display, setting <<308>> = Night/day

Menu 5

<<104>> = Vehicle messages

(12)

8 Menus

MID 128 = Engine system MID 136 = Brake system MID 130 = Gearbox system MID 223 = Gear selector system MID 222 = Retarder system MID 144 = Vehicle system MID 140 = Info display system MID 150 = Air suspension system MID 249 = Bodybuilder system MID 146 = Climate system MID 232 = Airbag system MID 219 = Adaptive cruise control MID 216 = Light control system MID 231 = Telephone

MID 163 = Immobilizer MID 179 = FMS Gateway MID 203 = Transp info system MID 250 = Steering Wheel Module MID 166 = Tyre pressure

<<1000>> = No data <<1001>> = HIGH <<1002>> = TOO HIGH <<1003>> = Icy conditions <<1004>> = Discharge <<1005>> = Refuel now. <<1007>> = LOW <<1008>> = TOO LOW <<1009>> = Check

(13)

<<1011>> = Stop, fault <<1012>> = Check data link

<<1013>> = Check data link open circuit <<1014>> = Low pressure

Menu 6

<<1040>> = Tyre pressure <<1041>> = Truck <<1042>> = Trailer 1 <<1043>> = Trailer 2 <<1044>> = Trailer 3 <<1045>> = Trailer 4 <<1046>> = Trailer 5

Menu 7

<<105>> = Reset

(14)

10 Menus

Menus when vehicle stationary

Menu 8

<<107>> = P-heater timer

<<212>> = Program

<<356>> = Set start date <<418>> = Set start time <<502>> = Set duration <<213>> = Reset <<214>> = No time programmed

Menu 9

<<108>> = Display setting <<200>> = Language

(15)

psi bar <<202>> = Time/Date <<313>> = Clock Format <<409>> = 24 h <<410>> = AM/PM <<314>> = Date format <<411>> = yymmdd <<412>> = ddmmyy <<413>> = mmddyy <<203>> = Display lighting <<315>> = Contrast <<316>> = Background lighting <<317>> = Night display <<1023>> = Inactive <<1024>> = Active

<<204>> = Enter new password

<<227>> = To see more menus, enter password <<319>> = Workshop password 2

(16)

12 Menus

<<321>> = Engine speed (max) <<415>> = Present value: <<416>> = Enter new value: rpm

<<1015>> = The transfer is complete. <<1016>> = Action unsuccessful. <<322>> = Road speed (max)

<<415>> = Present value: <<416>> = Enter new value: km/h, mph

<<1015>> = The transfer is complete. <<1016>> = Action unsuccessful. <<323>> = Fuel (target)

<<415>> = Present value: <<416>> = Enter new value: l/100 km, mpg

<<1015>> = The transfer is complete. <<1016>> = Action unsuccessful.

<<207>> = Ammeter calibration

<<417>> = Switch off all power consumers, then switch off the ignition. <<500>> = Calibration in progress, please wait

<<501>> = Sensor component modified. Switch the ignition on.

<<208>> = Fleet ID

<<324>> = Fleet id:

<<325>> = Enter new fleet id: <<1015>> = The transfer is complete. <<1016>> = Action unsuccessful.

<<211>> = Daytime running lights

(17)

<<302>> = Off

<<284>> = Draining/priming <<1048>> = Set wheel ID

<<1047>> = Set reference pressure

Menu 11

<<110>> = Diagnostics

<<215>> = Fault Diagnostics

MID 128 = Engine system MID 136 = Brake system MID 130 = Gearbox system MID 223 = Gear selector system MID 222 = Retarder system MID 144 = Vehicle system MID 140 = Info display system MID 150 = Air suspension system MID 249 = Bodybuilder system MID 184 = Rear axle steering MID 214 = Burglar alarm system MID 146 = Climate system MID 232 = Airbag system MID 219 = Adaptive cruise control MID 216 = Light control system MID 231 = Telephone

MID 219 = FMS Gateway MID 163 = Immobilizer MID 203 = Transp info system MID 220 = Tachograph

(18)

14 Menus

<<1017>> = Data transfer in progress, please wait. <<419>> = No errors

<<1016>> = Action unsuccessful <<420>> = Inactive

<<421>> = Active

<<423>> = More info? Press SELECT <<422>> = Number of events: <<503>> = First

<<504>> = Last AM

PM

<<505>> = Reset? Hold SELECT for 1 second

<<424>> = Reset all faults for this MID? Press SELECT for 1 second

<<216>> = Instrument test

<<326>> = Indicator lamp test <<327>> = Gauge test <<328>> = Display test <<329>> = Loudspeaker test

<<217>> = Part number

(19)

MID 214 = Burglar alarm system MID 146 = Climate system MID 232 = Airbag system MID 219 = Adaptive cruise control MID 216 = Light control system MID 231 = Telephone

MID 179 = FMS Gateway MID 163 = Immobilizer MID 203 = Transp info system MID 220 = Digital tachograph MID 166 = Tyre pressure system

<<1017>> = Data transfer in progress, please wait. <<430>> = Hardware number: <<431>> = Software number: <<1018>> = No data

Menu 12

<<111>> = Vehicle data <<221>> = Oil level <<331>> = min< <<332>> = >max

<<330>> = Not available. X min remaining.

(20)

16 Menus

Menu 13

<<112>> = Data log

<<223>> = Vehicle number

<<1017>> = Data transfer in progress, please wait <<333>> = Fleet id:

<<334>> = Chassis number: <<1018>> = No data

<<224>> = Totals

<<335>> = Total distance:

<<336>> = Total fuel consumption:

<<337>> = Total number of hours engine has been run: <<338>> = Total idling time:

<<339>> = Total power take off time:

<<340>> = Total number of engine revolutions:

<<225>> = Trip data

<<341>> = Trip distance:

<<342>> = Trip average fuel consumption: <<343>> = Trip total fuel consumption: <<344>> = Trip overrevs:

<<345>> = Trip uneconomic revs:

<<346>> = Trip consumption during uneconomic revs: <<347>> = Trip average fuel consumption:

<<348>> = Trip overspeed: <<349>> = Trip engine hours: <<350>> = Trip idling time:

(21)

<<226>> = Reset Trip data

<<433>> = Reset all trip data? Press SELECT for 1 second. <<1017>> = Data transfer in progress, please wait

<<1015>> = The transfer is complete. <<1016>> = Action unsuccessful

Menu 14

<<113>> = Password Entering, password

(22)

18 Numerical conversion table

General

In order to quickly see what each number means here is a list of all numbers in order together with the meaning.

(23)

208 Fleet id 209 Fog lights 210 Spotlights

211 Daytime running lights 212 Program 213 Reset 214 No time programmed 215 Fault diagnostics 216 Instrument test 217 Part number 218 General enquiry 219 Other systems 220 Reset all 221 Oil level 222 Load indicator 223 Vehicle number 224 Totals 225 Trip data 226 Reset trip data

(24)

20 Numerical conversion table

306 Background lighting 307 Favourite Display, setting 308 Night/day 309 No messages 310 Distance 311 Fuel consumption 312 Temperature 313 Clock Format 314 Date format 315 Contrast 316 Background lighting 317 Night display

318 Transport company, password 319 Workshop, password 2 320 Workshop, password 1 321 Engine speed (max) 322 Road speed (max) 323 Fuel (target) 324 Fleet id

325 Enter new fleet id 326 Indicator lamp test 327 Gauge test 328 Display test 329 Loudspeaker test

330 Not available. X min remaining. 331 min<

(25)

335 Total distance:

336 Total fuel consumption:

337 Total number of hours engine has been run: 338 Total idling time:

339 Total power take off time:

340 Total number of engine revolutions: 341 Trip distance:

342 Trip average fuel consumption: 343 Trip total fuel consumption: 344 Trip overrevs:

345 Trip uneconomic revs:

346 Trip consumption during uneconomic revs: 347 Trip average fuel consumption:

348 Trip overspeed: 349 Trip engine hours: 350 Trip idling time:

351 Trip idle fuel consumption 352 Trip power take-off time: 353 Trip power take-off fuel: 354 Trip cruise time: 355 Incorrect password. 356 Set start date

357 Draining/priming requested 358 Draining/priming not allowed

<<400>> to <<434>>

Number Meaning

400 Reset ALL fuel data? Press SELECT for 1 second 403 Reset? Press SELECT for 1 second.

(26)

22 Numerical conversion table

406 Reset ALL data? Press SELECT for 1 second.

409 24h

410 AM/PM

411 yymmdd 412 ddmmyy 413 mmddyy

414 Enter new password: 415 Present value: 416 Enter new value:

417 Switch off all power consumers, then switch off the ignition. 418 Set start time:

419 No errors 420 Inactive 421 Active

422 Number of events: 423 More info? Press SELECT

424 Reset all faults for this MID? Press SELECT for 1 second. 425 Reset ALL faults? Press SELECT for 1 second.

426 Alarm 427 Alarm clock 428 Warning 429 Turn indicators 430 Hardware number: 431 Software number: 432 Give over speed

(27)

<<500>> to <<506>>

500 Calibration in progress, please wait

501 Sensor component changed. Switch on the ignition 502 Set duration:

503 First: 504 Last:

505 Reset? Hold SELECT for 1 second. 506 Too many fault messages

<<1000>> to <<1096>> Number Meaning 1000 No data 1001 High 1002 Too high 1003 Icy conditions 1004 Discharge 1005 Refuel now 1007 Low 1008 Too low 1009 Check

1010 Check at next stop 1011 Stop. Fault. 1012 Check data link

1013 Check data link open circuit 1014 Low pressure

1015 The transfer is complete 1016 Action unsuccessful.

(28)

24 Numerical conversion table

1018 No data 1019 Welcome 1020 Pleasant journey! 1021 Incorrect password 1022 ACC, radar obscured 1023 Inactive

1024 Active

1025 ACC radar warming up 1026 ACC datalink problem 1027 Service of brake linings at: 1028 Brake linings are new. 1029 Brake linings need service. 1030 Disabling idle

1031 Disabling idle, cancelled 1032 Disabling of vehicle started 1033 Vehicle disabled

1034 Trailer, door locked 1035 Trailer, door unlocked 1036 Load, safety system enabled 1037 Load, safety system disabled 1038 Calibration:

(29)

1047 Set reference pressure 1048 Set wheel ID

1049 Enter new settings 1050 Select axle number 1051 Current value 1052 New value 1053 Set wheel ID 1054 Enter axle and wheel 1055 Current ID

1056 New ID 1057 No data

1058 Starter motor, overheating alarm 1059 Starter motor, gearbox not in neutral 1060 Starter motor, gear wheel sync. 1061 Start not possible, PTO enabled 1062 Stabilization, ACC sensor 1063 Reversing light trailer 1064 Fog light front 1065 Fog light rear 1066 Spotlight 1067 Reversing lights 1068 Brake lights 1069 Brake lights trailer 1070 Direction indicators, front 1071 Direction indicators, rear 1072 Direction indicators, trailer 1073 Parking lights

(30)

26 Numerical conversion table

1076 Check fuses 1077 Reduced light 1078 Brake light, reduced 1079 High beam

1080 Dipped beam 1081 No data, TPM 1082 Interior lighting 1085 Wait with start 1088 Select a lower gear 1089 Test SW installed in 1090 Reduced EGR system

1091 High pressure in diesel particulate filter 1092 Reduce charge pressure

1093 Reduce charge temp 1094 Vehicle safety mode

1096 LDWS disabled. Clean windscreen

MID 128 to MID 250

MID 128 Engine system MID 130 Gearbox system MID 136 Brake system MID 140 Info display system MID 144 Vehicle system MID 146 Climate system MID 150 Air suspension system MID 163 Immobilizer

(31)

MID 203 Transp. info system MID 214 Burglar alarm system MID 216 Lighting system MID 219 Adaptive cruise control MID 222 Retarder system MID 223 Gear selector system MID 231 Telephone

(32)

(33)

Index

C

Change language ... 3 Control stalk ... 1

D

Display control stalk ... 1

M

Menus ... 5

N

Numeric language, general ... 1 Numerical conversion table ... 18

P

Password protected menus ... 5

R

Red stop lamp + stop symbol ... 2

S

Stop message ... 2

T

(34)

Volvo Truck Corporation

Göteborg, Sweden