DD14 Series Intercept Fixed Mount

DD14 Series

Intercept

Fixed Mount

Installation/

Operation Manual

C291M-B (1/98)

Pelco • 3500 Pelco Way, Clovis • CA 93612-5699 USA • www.pelco.com In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150

2

Pelco Manual C291M-B (1/98)

CONTENTS

Section Page

1.0 GENERAL ... 5

1.1 IMPORTANT SAFEGUARDS AND WARNINGS ... 5

1.2 UNPACKING INSTRUCTIONS ... 6

2.0 DESCRIPTION ... 7

2.1 MODELS ... 7

3.0 INSTALLATION ... 8

3.1 FIXED MOUNT INSTALLATION ... 8

3.2 LENS WIRING ... 10

3.3 CAMERA/LENS INSTALLATION ... 10

3.4 ADJUSTMENTS ... 10

4.0 MAINTENANCE ... 11

4.1 FIXED MOUNT REMOVAL ... 11

5.0 EXPLODED ASSEMBLY DIAGRAM ... 12

6.0 SPECIFICATIONS ... 14

LIST OF ILLUSTRATIONS

Figure Page

1 Back Box and Fixed Mount Components ... 9 2 DD14 Fixed Mount Exploded Assembly Diagram ... 12

LIST OF TABLES

Table Page

A DD14 Fixed Mount Parts List ... 13

REVISION HISTORY

Manual # Date Comments

C291M — Original version.

C291M-A 6/95 Rev A. Update manual to show new rocker style power switch.

4

Pelco Manual C291M-B (1/98)

Please thoroughly familiarize yourself with the information

in this manual prior to installation and operation.

1.0 GENERAL

1.1 IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes.

2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture.

3. Only use replacement parts recommended by Pelco.

4. After replacement/repair of this unit’s electrical components, conduct a resis-tance measurement between line and exposed parts to verify the exposed parts have not been connected to line circuitry.

5. The installation method and materials should be capable of supporting four (4) times the weight of the enclosure, pan/tilt, camera and lens combination.

The product and/or manual may bear the following marks:

This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN. CAUTION:

TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING

6

Pelco Manual C291M-B (1/98)

1.2 UNPACKING INSTRUCTIONS

Unpack and inspect all parts carefully.

Be sure to save the shipping carton and any inserts. They are the safest material in which to make future shipments.

The following items are supplied: 1 Fixed mount

1 Dome liner 1 1/4-20 x 1/2" bolt 1 1/4" flat washer 1 1/4" split lock washer

1 Installation/Operation Manual (C291M-B)

If an item appears to have been damaged in shipment, replace it properly in its carton and contact the factory at 1-800-289-9100 or 1-209-292-1981 for a replace-ment. (International customers fax 1-209-348-1120 for authorization and instruc-tions.)

2.0 DESCRIPTION

The DD14A0L fixed mount is part of the IDS14 Intercept® _{Series of domes. The}

fixed mount requires a back box to make a complete system.

This manual covers the DD14A0L fixed mount only. For installation and operation instructions for the back box, refer to manual C454M-C.

2.1 MODELS

8

Pelco Manual C291M-B (1/98)

3.0 INSTALLATION

Proceed with the installation of the fixed mount after you have installed the back box.

If a camera/lens package has not been installed on your fixed mount, you can in-stall the camera/lens either before you inin-stall the fixed mount in the back box or after you install the fixed mount. If you want to install the camera/lens first, proceed to Sections 3.2, LENS WIRING, and 3.3, CAMERA/LENS INSTALLATION, then return to Section 3.1, FIXED MOUNT INSTALLATION.

3.1 FIXED MOUNT INSTALLATION

2. Remove the hairpin clips from the two latches inside the back box (refer to Figure 1) and open the latches.

3. Insert the fixed mount into the back box:

a. Refer to Figure 1 and line up the upper backet on the dome so that: The 25-pin connector on the fixed mount will go into its mating connector on the back box.

The latch pins on the side of the upper bracket will go into the latches in the back box.

The two guide pins on the back box will go into the bushings on the upper bracket of the fixed mount.

b. Push the fixed mount into place and close the latches.

c. Reinstall the hairpin clips in the latches to prevent the latches from open-ing.

25-PIN CONNECTOR LATCH LATCH

GUIDE PIN GUIDE PIN

HAIRPIN CLIP

HAIRPIN CLIP

Figure 1. Back Box and Fixed Mount Components

LATCH PIN BUSHING BUSHING LATCH PIN

25-PIN CONNECTOR BACK BOX

10

Pelco Manual C291M-B (1/98)

3.2 LENS WIRING

Refer to the back box manual for wiring pinouts and wire the lens according to the manufacturer’s instructions.

Proceed to Section 3.3, CAMERA/LENS INSTALLATION.

3.3 CAMERA/LENS INSTALLATION

1. Attach the camera/lens to the tilt table using the 1/4-20 x 1/2" bolt, flat washer, and lock washer that are supplied.

2. Connect the camera power spade lugs and coaxial video cable.

Proceed to Section 3.4, ADJUSTMENTS.

3.4 ADJUSTMENTS

1. Loosen the horizontal positioning lock-down knob, rotate the mount the de-sired position, and re-tighten the knob.

2. Loosen the vertical positioning lock-down knob, adjust the tilt table to the de-sired position, and re-tighten the knob.

3. Install the dome liner: Push the studs on the liner into the mount bracket. Make sure the window slot is aligned with the lens.

Ensure there is sufficient clearance between the camera/lens and the dome liner. Reposition the camera/lens and wiring as necessary to achieve clear-ances.

4. Reach into the back box and turn on the power switch (if applicable to your back box.

5. Suspended/Hard Ceiling Models - Attach the trim ring and dome to the back box.

Pendant Models - Align the three bezel pins with the large hole in the back box brackets, push the bezel up and rotate clockwise to latch.

Attach the back box gasket to the rim of the back box to provide an air-tight seal between the back box and the bezel.

4.0 MAINTENANCE

Clean the acrylic dome as necessary to provide a clear picture. Clean the dome with a nonabrasive cleaning cloth and antistatic cleaner that is safe for use on acrylic plastic.

4.1 FIXED MOUNT REMOVAL

1. Pendant Models Only - Remove the gasket from the rim of the back box.

2. Remove the back box trim ring or bezel. To remove a bezel, turn it about 1/2" (1.27 cm) counterclockwise and pull down.

3. Turn off the power switch.

4. Remove the hairpin clips from the latches. 5. Open one of the latches.

6. Grasp the unit with one hand to prepare for the 10- to 13-pound (4.5-5.9 kg) load.

12

Pelco Manual C291M-B (1/98)

5.0 EXPLODED ASSEMBLY DIAGRAM

G H D E 1 2 8 A J 15 E F K L 16 C 7 13 N 10 D 9 I E 12 E M 11 17 14 B E I 5 6 4 3 P

Item Quantity Description Part Number

1 2 Bushing 80010004

2 2 Push nut 80010011

3 1 Upper mount bracket 8004034COMP

4 1 Spindle bracket 8004037COMP

5 1 Frame 8004019COMP

6 2 Dome bracket 8004020COMP

7 1 Tilt table 8004021COMP

8 2 Latch pin 8004145COMP

9 1 ABS dome liner 81410002

10 1 Dome plate, receiver side 8144002COMP

11 1 Dome plate, tilt side 8144003COMP

12 1 Dome brace 8144004COMP

13 4 Ball stud PT180410000

14 2 Gray knob, 1/4-20 tapped CM1610003

15 1 25-position connector receptacle CON10J025Z41T

16 4 Ball stud receiver PT180410001

17 1 Cross bar 8004043COMP

18 6 Crimp pin, loose piece (not shown) CON66107-2

(for use with item #15)

19 1 BNC crimp connector for RG174 Coax (not shown) CONCPM88-174

A 2 Screw, 1/4-20 x 1" flat head, Phillips ZH1/420X1.00SFS

B 1 Allen screw, 1/4-20 x 1" ZH1/420X1.00SS

C 1 Lock nut, 1/4-20, nylon insert ZH1/420NUTCHN

D 6 Screw, 6-32 x 3/8" pan head, Phillips ZH6-32X.375SPP

E 18 Internal star washer, #6 ZH6LWSIS

F 2 Screw, 6-32 x 1/2" pan head, Phillips ZH6-32X.500SPP

G 4 Screw, 8-32 x 1/2" pan head, Phillips ZH8-32X.500SPP

H 4 Internal star washer, #8 ZH8LWSIS

I 8 Screw, 6-32 x 3/8" flat head, Phillips, black ZH6-32X.375BPF

J 2 Spacer, 1/4" hex x 1/2" long, 6-32 tapped SPA8423

K 1 Fender washer, 1/4" x 1.5" x 14" ga, black ZH255X1.50X62

L 1 Split lock washer, 1/4" ZH1/4LWSSL

M 10 Nut, 6-32 ZH6-32NUTSH

N 4 Spacer, 1/4" O.D. x 1/8" long, #6 clear SPA8500

P 6 Screw, 6-32 x 3/8" pan head, Phillips, black ZH6-32X.375BPP

14

Pelco Manual C291M-B (1/98)

6.0 SPECIFICATIONS

MECHANICAL

Pan: 360° movement in horizontal plane Tilt: -90° movement from horizontal plane Approximate

Camera/Lens

Size: Maximum total length of camera/lens 11.5" (29.21 cm) includ-ing BNC cable connection to camera; max. lens width 4.70" (11.93 cm); max. lens height 3.20" (8.13 cm)

Connectors

Video: BNC

Camera Power: Spade lugs

GENERAL

Construction

Fixed Mount: Aluminum with stainless steel hardware Dome Liner: Plastic

Weight: 4.1 lbs (1.85 kg)

16

Pelco Manual C291M-B (1/98)

7.0 WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or workman-ship for a period of one year after the date of workman-shipment.

Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex® _{Series products (multiplexers, server, and keyboard).}

• Three years on Camclosure® _{and fixed camera models, except the CC3701H-2, CC3701H-2X,}

CC3751H-2, CC3651H-2X, MC3651H-2, and CC3651H-2X camera models, which have a five-year warranty.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy®_{, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series}

fixed dome products.

• Two years on Spectra®_{, Esprit}®_{, ExSite}™_{, and PS20 Scanners, including when used in continuous}

motion applications.

• Two years on Esprit® _{and WW5700 Series window wiper (excluding wiper blades).}

• Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura™ Series distributed network-based video products.months on DX Series digital video re-corders, NVR300 Series network video rere-corders, Endura™ _{Series distributed network-based video}

products, and TW3000 Series twisted pair transmission products.

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the spe-cific use or application made of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number 3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the warranty condi-tions stated above, please include a written explanation with the product when returned.

Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge. Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to: Service Department

Pelco 3500 Pelco Way Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to: Pelco

3500 Pelco Way

Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to: Pelco c/o Expeditors

473 Eccles Avenue

South San Francisco, CA 94080 USA Phone: 650-737-1700

Fax: 650-737-0933

® Pelco, the Pelco logo, Spectra, Esprit, Genex, Legacy, and Camclosure are registered trademarks of Pelco.