Evaluation Board. i-modul and Socket. Manual

(1)

Evaluation Board

i-modul and Socket

Ma

nu

(2)

(3)

Any duplication of this manual is prohibited. All rights on this documentation and the devices are with INSYS MICROELECTRONICS GmbH Regensburg.

Trademarks

The use of a trademark not shown below is not an indication that it is freely availa-ble for use.

MNP is a registered trademark of Microcom Inc.

IBM PC, AT, XT are registered trademarks of International Business Machine Cor-poration.

INSYS®, e-Mobility LSG® and e-Mobility PLC® are registered trademarks of INSYS MICROELECTRONICS GmbH.

Windows™ is a registered trademark of Microsoft Corporation. Linux is a registered trademark of Linus Torvalds.

Publisher: INSYS MICROELECTRONICS GmbH Hermann-Köhl-Str. 22 D-93049 Regensburg, Germany Phone: +49 941 58692 0 Fax: +49 941 58692 45 E-mail: [email protected] Internet: http://www.insys-icom.com Date: Mar-14 Item: 31-22-09.001 Version: 1.0 Language: EN

(4)

Content 4 Mar-14 1 Overview ... 5 2 Technical Specification ... 6 2.1 Connectors ... 6 2.2 Multi-pin connectors ... 6 2.3 Jumpers ... 7 3 Initial operation ... 8 3.1 Configuration of i-modules ... 9

3.2 Configuration of Socket mode ... 10

3.3 Step-by-step inital operation instructions ... 10

4 Evaluation Board and module plug ports ... 11

(5)

1 Overview

The Evaluation board is intended to be used for customer specific implementations and tests for the following INSYS i-modul and INSYS socket products:

 Modem  ISDN  GSM  EDGE  HSPA  Ethernet  GPRS  WLAN  Bluetooth Special Features:

 Socket and i-modul support

 D-SUB listen ports for RxD and TxD  Phone jack for speaker

 Phone jack for microphone

 Terminal and coaxial power supply

(6)

Technical Specification Fehler! Kein Text mit angegebener Formatvorlage im Dokument.

2 Technical Specification

Dimensions: 160mm x 100mm

Power supply: _{9 VAC - 12 VAC}

10 VDC - 15 VDC

Current drain: max. 1.5A (Peak at GSM)

max. 0.3A (ISDN, Modem, Ethernet, WLAN)

2.1 Connectors

CON401 Screwing terminal for power supply

CON11 Coax jack for power supply

CON16 SUB D jack for RS232 connection

CON301 RJ45 jack for Modem/ISDN/Ethernet- connection

CON303/CON304 Screwing terminal for phone connection

CON2 SUB D jack for RS232 listen port RxD

CON3 SUB D jack for RS232 listen port TxD

CON13 3,5mm jack for speaker

CON12 3,5mm jack for microphone

2.2 Multi-pin connectors

CON18 Multi-pin connector for field strength, OH, status, sync

JP100 Multi-pin connector for RS232 signals

CON110 Multi-pin connector for RESET

J401 Multi-pin connector GND and VCC connection

(7)

2.3 Jumpers

JP1 Setting for i-modul (Pin assignment)

JP7 Microphone supply

JP100 Jumpers for serial interface

JP8 Jumper for on-board speaker

JP9 Switching between 3,3V (open) und 5V (bridged)

JP10 Setting for Socket

(8)

Initial operation Fehler! Kein Text mit angegebener Formatvorlage im Dokument.

3 Initial operation

In principle there is a difference in configuration of i-modules and socket modules. Depending on the plugged-on module the correct jumper settings must be checked before switching on the evaluation board.

Warning!

With voltage not adjusted properly the is danger of overheating of components..

Hot surfaces!

Take care jumper JP9 is configured properly. In case components become hot, cut electrical supply and have components cool down

(9)

3.1 Configuration of i-modules

Use jumpers J1-J6 and JP9 (bridged = 5V) if you want to configure an i-modul Mo-dem/ISDN or an i-modul Ethernet/WLAN bridge.

The jumper settings for modul Modem correspond to the jumper settings for i-modul ISDN.

Configuration Modem/ISDN

Configuration

Ethernet a/WLAN bridge a

Configuration

Ethernet b/WLAN bridge b

Note

When using an i-modul GSM, GPRS, WLAN serial and Blue-tooth the jumpers JP1 – JP6 as well as the connectors CON301 and CON303/304 are without function.

(10)

Initial operation Fehler! Kein Text mit angegebener Formatvorlage im Dokument.

3.2 Configuration of Socket mode

In order to configure the evaluation board for socket modules (Modem/Ethernet, ISDN) the jumpers JP9 – JP13 have to be used. JP9 should be open with 3,3V-modules.

The jumper settings for Modem correspond to the Ethernet settings.

Configuration Modem Configuration Ethernet Configuration ISDN

3.3 Step-by-step inital operation instructions

Please follow these steps when plugging on a new i-modul or socket module: 1. Plug on the module carefully.

2. Configure the modul type with jumpers JP1 – JP6 and JP9 (i-modul and socket) respectively JP10 – JP13 (socket only).

3. Connect the serial interface CON16 by a standard serial cable with your computer.

4. Connect the power supply either by connector CON401 or by jack CON11. The polarity is irrelevant.

5. Start your terminal program on your computer (e.g. Hyperterminal or TeraTerm). 6. Switch on power supply (LED “PWR” is lit).

7. Type AT<RETURN> in the terminal program of your computer.

8. The module answers by sending OK back to the terminal program. When using a module without the autobauding feature you have to check the baud rate of your terminal program before the communication can be established

successfully. If there is no answer from the module even after checking the communication settings you have to immediately switch off the power supply and check if the i-modul or socket module is plugged on correctly and if all jumpers are set as described in this manual.

(11)

4 Evaluation Board and module plug ports

Port for i-modules  144/336/56k  GSM  GPRS  Bluetooth  Ethernet  WLAN

(12)

Evaluation Board and module plug ports Fehler! Kein Text mit angegebener Formatvorlage im Dokument. Port for i-modul  ISDN HIT  ISDN HIX Note

The bolt has to be removed before plugging on the module.

(13)

Port

for socket mod-ules

(14)

Circuit diagram Fehler! Kein Text mit angegebener Formatvorlage im Dokument.

(15)

(16)

Circuit diagram Fehler! Kein Text mit angegebener Formatvorlage im Dokument.

(17)

(18)