Technical Data
Valid for model year 2013
02 – General information – The Crafter
Information on fuel consumption and CO2 emissions can be found within the technical data.
Not all combinations of engine, gearbox and auto body design are possible. Please discuss your individual requirements with your Volkswagen Commercial Vehicles dealer. Only your Volkswagen Commercial Vehicles dealer is able to check the necessary combination requirements as well as verify the accuracy and completeness of data in the purchasing system. The payloads listed here have been established allowing for factory options or other tailored solutions that are not included in the standard scope of delivery and services. The actual payload of a vehicle, which is calculated by the difference between the gross vehicle weight and the curb weight, can only be established by weighing the individual vehicle. The product name Caddy® is a registered brand name of Caddie S.A. and is used by Volkswagen Commercial Vehicles with the kind approval of Caddie S.A.
TDI®, DSG®, Shiftmatic®, 4MOTION® and BlueMotion® are registered brand names of Volkswagen AG and other companies in the Volkswagen Group in Germany as well as in other
countries. The fact that a brand name in this document is not marked with ® does not mean that it is not a registered brand name and/or that this brand name may be used without the written approval of the Volkswagen AG. Not all brand names mentioned are necessarily a part of these technical details.
Our vehicles are equipped with summer tyres as standard. As of the 12.04.2010, in the Federal Republic of Germany you are legally oblieged to equipe your vehicle in icy conditions, packed snow, slash, ice or hoar frost with winter tyres or all seasons tyres. Please contact your Volkswagen Commercial Vehicles dealer for assistance.
Take-back and recycling of end of life vehicles:
Volkswagen meets the challenges of modern society and takes them into consideration in all new products of the Volkswagen brand. This naturally also applies to protection of the environment and resources. All new Volkswagens can therefore be recycled in an environment-friendly way and can be returned free of charge, subject to fulfilment of national legislation. For details concerning take-back and recycling of end of life vehicles, please contact your local Volkswagen dealer, refer to the Internet on www.volkswagen.de or call the hotline +49 800 - Volkswagen (+49 800 865 579 2436), free for callers in Germany.
The data provided in this data sheet is in accordance with the information available at the time of going to print and are based on the features of the German market. Your Volkswagen dealer can provide you with information on country-specific differences.
– Fuel consumptionand CO2 emissions for Crafter models with emission standard EEV (stricter than EURO V) – The Crafter – Fuel consumptionand COThe Crafter2 emissions for Crafter models with emission standard EEV (stricter than EURO V) –
Fuel consumption
and CO
2emissions for Crafter models with emission standard EEV
1)(stricter than EURO V).
With manual gearbox2), fuel consumption (litres/100 km) and combined CO
2 emissions (g/km), fuel tank capacity approx. 75 litres
Engine 2.0 l TDI (80 kW) 2.0 l BiTDI (105 kW) 2.0 l BiTDI (120 kW)
Rear-axle
ratio 3.923:1 4.182:13) 4.364:1 3.923:1 4.182:13) 4.364:1 3.692:1 3.923:13) 4.182:1
Crafter 30/35 Delivery Van
urban 9.4 – 9.4 10.1 – 10.6 10.8 – 11.3 9.2 – 9.2 9.9 – 10.2 10.6 – 11.1 8.9 – 9.0 9.2 – 9.2 9.9 – 10.2
extra-urban 7.7 – 8.1 7.8 – 7.9 8.1 – 8.3 7.5 – 7.9 7.6 – 7.8 7.9 – 8.1 7.3 – 7.7 7.5 – 7.9 7.6 – 7.8
combined 8.3 – 8.6 8.6 – 8.9 9.1 – 9.4 8.1 – 8.4 8.4 – 8.7 8.9 – 9.2 7.9 – 8.2 8.1 – 8.4 8.4 – 8.7
CO2 emissions
combined 218 – 226 226 – 234 239 – 247 213 – 221 221 – 229 234 – 242 208 – 216 213 – 221 221 – 229
Crafter 30/35 Delivery Van with start/stop system4)
urban 9.6 – 10.0 10.3 – 10.7 9.2 – 9.5 10.1 – 10.5 8.7 – 8.7 9.2 – 9.5
extra-urban 7.6 – 7.9 7.9 – 8.1 7.5 – 7.8 7.7 – 8.1 7.3 – 7.7 7.5 – 7.8
combined 8.3 – 8.6 8.8 – 9.1 8.1 – 8.4 8.6 – 8.9 7.8 – 8.1 8.1 – 8.4
CO2 emissions
combined 218 – 227 231 – 239 213 – 221 226 – 234 205 – 213 213 – 221
Crafter 30/35 Delivery Van with BlueMotion Technology
urban 8.6 – 8.9 8.7 – 8.7 8.2 – 8.5
extra-urban 7.7 – 7.9 7.3 – 7.7 7.3 – 7.5
combined 8.0 – 8.3 7.8 – 8.1 7.6 – 7.9
CO2 emissions
combined 210 – 218 205 – 213 200 – 208
1) “Enhanced Environmentally Friendly Vehicle”, the figures established are below the limits set by the EURO V emission standard. 2) Figures are not available for Crafter 50. 3) Standard rear-axle ratio. 4) Start/stop system available as an optional extra.
The fuel consumption and emission values listed here have been established in accordance with the measuring method stipulated (ECE-R 101). CO2 emissions arising from the production
and provision of fuel and/or other energy sources are not taken into consideration when determining the CO2 emissions in accordance with directive 1999/94/EC. These figures do not
refer to the particular vehicle and do not constitute part of the offer but are purely for comparison purposes between the various types of vehicle. In addition to the fuel efficiency of a vehicle, driving behaviour as well as other non-technical factors play a role in determining a vehicle’s fuel consumption and CO2 emissions. CO2 is the main greenhouse gas responsible
for global warming.
With Shiftmatic2), fuel consumption (litres/100 km) and combined CO
2 emissions (g/km), fuel tank capacity approx. 75 litres
Engine 2.5 l BlueTDI (100 kW)
Rear-axle
ratio 4.182:13) 4.364:1
Crafter 30/35 Delivery Van
urban 10.3 10.6
extra-urban 8.5 8.7
combined 9.1 9.4
CO2 emissions
The Crafter – Fuel consumption, CO2 emissions and efficiency categories Crafter 4MOTION –
– Fuel consumption, CO2 emissions and efficiency categories Crafter 4MOTION – The Crafter
Fuel consumption, CO
2emissions and efficiency categories Crafter 4MOTION.
With manual gearbox1), fuel consumption (litres/100 km) and combined CO
2 emissions (g/km), fuel tank capacity approx. 75 litres
Engine 2.0 l BiTDI (120 kW)
Rear-axle ratio 4.111:1 (Crafter 4MOTION with Achleitner four-wheel drive)
Crafter 35 Delivery Van (emission standard EEV2) [stricter than EURO V])
urban 10.2
extra-urban 7.8
combined 8.7
CO2 emissions combined 229
Crafter 35 Kombi (emission standard EEV2) [stricter than EURO V])
urban 10.2 extra-urban 7.8 combined 8.7 CO2 emissions combined 229 efficiency category with normal roof, short wheelbase/medium wheelbase/– C/C/– efficiency category with high roof, –/medium wheelbase/long wheelbase –/C/C 1) Figures are not available for Crafter 50. 2) “Enhanced Environmentally Friendly Vehicle”, the figures established are below the limits set by the EURO V emission standard. The fuel consumption and emission values listed here have been established in accordance with the measuring method stipulated (ECE-R 101). CO2 emissions arising from the production and provision of fuel and/or other energy sources are not taken into consideration when determining the CO2 emissions in accordance with directive 1999/94/EC. These figures do not refer to the particular vehicle and do not constitute part of the offer but are purely for comparison purposes between the various types of vehicle. In addition to the fuel efficiency of a vehicle, driving behaviour as well as other non-technical factors play a role in determining a vehicle’s fuel consumption and CO2 emissions. CO2 is the main greenhouse gas responsible for global warming. Note in accordance with the currently valid version of directive 1999/94/EC: A guide on the official fuel consumption and the official specific CO2 emissions and power
consumption for all new passenger car models is available free of charge at every point of sale in the European Union and, for prospective buyers in Germany, at DAT Deutsche Automo-bil Treuhand GmbH, Hellmuth-Hirth-Strasse 1, 73760 Ostfildern. Efficiency categories evaluate vehicles based on CO2 emissions while taking the unladen weight of the vehicle into consideration. Vehicles that comply with the average are classified as D. Vehicles that are above the current average are classified as A+, A, B or C. Vehicles that are below average are
– Fuel consumption and CO2 emissions for Crafter models with emission standard Euro 5 – The CrafterThe Crafter – Fuel consumption and CO2 emissions for Crafter models with emission standard Euro 5 –
Fuel consumption and CO
2emissions for Crafter models with emission standard Euro 5.
1) Figures are not available for Crafter 50. 2) Standard rear-axle ratio. 3) Start/stop system available as an optional extra.
The fuel consumption and emission values listed here have been ascertained in accordance with the measuring method stipulated (the version of the EC directive 715/2007 which is currently valid). CO2 emissions arising from the production and provision of fuel and/or other energy sources are not taken into consideration when determining the CO2 emissions in
accordance with directive 1999/94/EC. These figures do not refer to a particular vehicle and do not constitute part of the offer but are purely for comparison purposes between the various types of vehicle. In addition to the fuel efficiency of a vehicle, driving behaviour as well as other non-technical factors play a role in determining a vehicle’s fuel consumption and CO2
emissions. CO2 is the main greenhouse gas responsible for global warming.
With manual gearbox1), fuel consumption (litres/100 km) and combined CO
2 emissions (g/km), fuel tank capacity approx. 75 litres
Engine 2.0 l TDI (80 kW) 2.0 l TDI (100 kW) 2.0 l BiTDI (120 kW)
Rear-axle
ratio 3.923:1 4.182:12) 4.364:1 3.923:1 4.182:12) 4.364:1 3.692:1 3.923:12) 4.182:1
Crafter 30 Delivery Van BlueMotion (with short wheelbase and normal roof)
urban 7.9 – 8.0 7.9 – 8.0
extra-urban 6.5 – 6.6 6.5 – 6.6
combined 7.0 – 7.1 7.0 – 7.1
CO2 emissions
combined 184 – 187 184 – 187
Crafter 30/35 Delivery Van (only models with a maximum unladen weight of 2,815 kg incl. conversions)
urban 9.1 – 9.4 10.1 – 10.7 10.5 – 10.8 9.1 – 9.4 10.1 – 10.7 10.5 – 10.8 8.7 – 9.0 9.0 – 9.2 9.9 – 10.3
extra-urban 7.9 – 8.1 7.8 – 7.9 8.4 – 8.6 7.9 – 8.1 7.8 – 7.9 8.4 – 8.6 7.5 – 7.7 7.6 – 7.9 7.6 – 7.8
combined 8.3 – 8.6 8.6 – 8.9 9.1 – 9.4 8.3 – 8.6 8.6 – 8.9 9.1 – 9.4 7.9 – 8.2 8.1 – 8.4 8.4 – 8.7
CO2 emissions
combined 218 – 226 226 – 234 239 – 247 218 – 226 226 – 234 239 – 247 208 – 216 213 – 221 221 – 229
Crafter 30/35 Delivery Van with start/stop system3) (only models with a maximum unladen weight of 2,815 kg incl. conversions)
urban 9.6 – 10.0 10.0 – 10.3 9.6 – 10.0 10.0 – 10.3 8.4 – 8.7 9.4 – 9.6
extra-urban 7.6 – 7.7 8.2 – 8.4 7.6 – 7.7 8.2 – 8.4 7.5 – 7.7 7.4 – 7.7
combined 8.3 – 8.6 8.8 – 9.1 8.3 – 8.6 8.8 – 9.1 7.8 – 8.1 8.1 – 8.4
CO2 emissions
combined 218 – 226 231 – 239 218 – 226 231 – 239 205 – 213 213 – 221
Crafter 30/35 Delivery Van with BlueMotion Technology (only models with a maximum unladen weight of 2,815 kg incl. conversions)
urban 8.6 – 8.9 8.6 – 8.9 8.2 – 8.5
extra-urban 7.7 – 7.9 7.7 – 7.9 7.3 – 7.5
combined 8.0 – 8.3 8.0 – 8.3 7.6 – 7.9
CO2 emissions
The Crafter – Fuel consumption, CO2 emissions and efficiency categories for Crafter models with emission standard Euro 5 –
– Fuel consumption, CO2 emissions and efficiency categories for Crafter models with emission standard Euro 5 – The Crafter
Fuel consumption, CO
2emissions and efficiency categories for Crafter models with emission standard Euro 5.
1) Standard rear-axle ratio. 2) Start/stop system available as an optional extra.
The values listed here have been ascertained in accordance with the measuring method stipulated (§ 2 Nrs. 5, 6, 6a of the German energy labeling directive for cars in the currently valid version). CO2 emissions arising from the production and provision of fuel and/or other energy sources are not taken into consideration when determining the CO2 emissions in accordance
with directive 1999/94/EC. These figures do not refer to a particular vehicle and do not constitute part of the offer but are purely for comparison purposes between the various types of vehicle. In addition to the fuel efficiency of a vehicle, driving behaviour as well as other non-technical factors play a role in determining a vehicle’s fuel consumption and CO2 emissions. CO2 is the main greenhouse gas responsible for global warming. Note in accordance with the currently valid version of directive 1999/94/EC: A guide on the official fuel consumption and the official specific CO2 emissions and power consumption for all new passenger car models is available free of charge at every point of sale in the European Union and, for prospective buyers in Germany, at DAT Deutsche Automobil Treuhand GmbH, Hellmuth-Hirth-Strasse 1, 73760 Ostfildern. Efficiency categories evaluate vehicles based on CO2 emissions while taking the unladen weight of the vehicle into consideration. Vehicles that comply with the average are classified as D. Vehicles that are above the current average are classified as A+, A, B or C. Vehicles that are below average are characterised as E, F or G.
With manual gearbox, fuel consumption (litres/100 km) and combined CO2 emissions (g/km), fuel tank capacity approx. 75 litres
Engine 2.0 l TDI (80 kW) 2.0 l TDI (100 kW) 2.0 l BiTDI (120 kW)
Rear-axle ratio 3.923:1 4.182:11) 4.364:1 3.923:1 4.182:11) 4.364:1 3.692:1 3.923:11) Crafter 30/35 Kombi urban 9.0 9.9 10.2 9.0 9.9 10.2 8.5 8.9 extra-urban 7.3 7.2 7.9 7.3 7.2 7.9 6.9 7.0 combined 7.9 8.2 8.7 7.9 8.2 8.7 7.5 7.7 CO2 emissions combined 208 216 229 208 216 229 197 203 efficiency category for Crafter 30 with normal
roof, short wheelbase/medium wheelbase/– D/D/– E/E/– E/E/– D/D/– E/E/– E/E/– D/D/– D/D/–
efficiency category for Crafter 35 with normal
roof, short wheelbase/medium wheelbase/– D/D/– E/D/– E/E/– D/D/– E/D/– E/E/– D/D/– D/D/–
efficiency category for Crafter 30 with high roof,
–/medium wheelbase/– –/D/– –/D/– –/E/– –/D/– –/D/– –/E/– –/C/– –/D/–
efficiency category for Crafter 35 with high roof,
–/medium wheelbase/long wheelbase –/D/C –/D/D –/E/D –/D/C –/D/D –/E/D –/C/C –/D/C
Crafter 30/35 Kombi with start/stop system2)
urban 9.4 9.7 9.4 9.7 8.3
extra-urban 7.0 7.7 7.0 7.7 6.9
combined 7.9 8.4 7.9 8.4 7.4
CO2 emissions combined 208 221 208 221 195
Crafter 30/35 Kombi with BlueMotion Technology
urban 8.3 8.3 8.0
extra-urban 7.1 7.1 6.7
combined 7.6 7.6 7.2
CO2 emissions combined 199 199 189
efficiency category for Crafter 30 with normal
roof, short wheelbase/medium wheelbase/– D/D/– D/D/– E/E/– D/D/– D/D/– E/E/– C/C/– D/C/–
efficiency category for Crafter 35 with normal
roof, short wheelbase/medium wheelbase/– D/D/– D/D/– E/E/– D/D/– D/D/– E/E/– C/C/– D/C/–
efficiency category for Crafter 30 with high roof,
–/medium wheelbase/– –/D/– –/D/– –/E/– –/D/– –/D/– –/E/– –/C/– –/C/–
efficiency category for Crafter 35 with high roof,
– Engines – The Crafter The Crafter – Engines –
Engines.
1) “Enhanced Environmentally Friendly Vehicle”, the figures established are below the limits set by the EURO V emission standard. 2) Road tax ratings in Germany are in accordance with the code numbers laid down by the Federal Motor Transport Authority. 3) Not available for Crafter Kombi.
Diesel engines 2.0 l TDI engine (80 kW) 2.0 l TDI engine (100 kW)
(only with Crafter 30/35)
Mixture preparation/injection method common rail direct injection common rail direct injection
No. of cylinders 4 4
Cubic capacity, cm3 1,968 1,968
Output, kW at rpm 80 at 3,500 100 at 3,500
Max. torque, Nm/rpm 300/1,500 – 2,250 340/1,575 – 2,250
EU exhaust emission directive EEV1) according to regulation 2005/55/EC,
version 2008/74/EC or according to EC
regulation 715/2007 Euro 5 respectively2)
according to EC regulation 715/2007 Euro 52)
Diesel particulate filter (DPF) standard standard
6-speed manual gearbox standard standard
Rear-wheel drive standard standard
Type of fuel diesel, in accordance with DIN EN 590 diesel, in accordance with DIN EN 590
Diesel engines 2.5 l BlueTDI engine (100 kW)3) 2.0 l BiTDI engine (105 kW)
Mixture preparation/injection method common rail direct injection BiTurbo common rail direct injection
No. of cylinders 5 4
Cubic capacity, cm3 2,461 1,968
Output, kW at rpm 100 at 3,500 105 at 3,500
Max. torque, Nm/rpm 330/2,000 340/1,575 – 2,250
EU exhaust emission directive EEV1) according to regulation 2005/55/EC,
version 2008/74/EC EEV
1) according to regulation 2005/55/EC,
version 2008/74/EC
Diesel particulate filter (DPF) standard standard
6-speed manual gearbox/6-speed Shiftmatic –/standard standard/–
Rear-wheel drive standard standard
Type of fuel diesel, in accordance with DIN EN 590 diesel, in accordance with DIN EN 590
Diesel engine 2.0 l BiTDI engine (120 kW)
Mixture preparation/injection method BiTurbo common rail direct injection
No. of cylinders 4
Cubic capacity, cm3 1,968
Output, kW at rpm 120 at 3,600
Max. torque, Nm/rpm 400/1,800
EU exhaust emission directive EEV1) according to regulation 2005/55/EC,
version 2008/74/EC or according to EC regulation 715/2007 Euro 5 respectively2) Diesel particulate filter (DPF) standard 6-speed manual gearbox standard Rear-wheel drive standard Type of fuel diesel, in accordance with DIN EN 590 engine speed [rpm] tor que [ Nm] output [kW] 80 kW 1000 2.0 l TDI (EEV/Euro 5) 140 80 60 40 20 250 200 150 100 50 300 100 120 2000 3000 4000 5000 300 Nm 80 kW engine speed [rpm] tor que [ Nm] output [kW] 100 kW 1000 2.0 l TDI (Euro 5) 140 80 60 40 20 250 200 150 100 50 300 400 350 100 120 2000 3000 4000 5000 340 Nm 100 kW engine speed [rpm] tor que [ Nm] output [kW] 100 kW 1000 2.5 l BlueTDI (EEV) 140 80 60 40 20 250 200 150 100 50 300 400 350 100 120 2000 3000 4000 5000 330 Nm 100 kW engine speed [rpm] tor que [ Nm] output [kW] 105 kW 1000 2.0 l BiTDI (EEV) 140 80 60 40 20 250 200 150 100 50 300 400 350 100 120 2000 3000 4000 5000 340 Nm 105 kW engine speed [rpm] tor que [ Nm] output [kW] 120 kW 1000 2.0 l BiTDI (EEV/Euro 5) 140 80 60 40 20 250 200 150 100 50 300 400 350 100 120 2000 3000 4000 5000 400 Nm 120 kW
The Crafter – Top speeds –
– Top speeds – The Crafter
Top speeds.
1) Standard rear-axle ratio for Crafter Delivery Van BlueMotion (only for Crafter 30 with normal roof and 80 kW or 100 kW) as well as BlueMotion Technology. 2) Standard rear-axle ratio. 3) The maximum speeds shown here refer to non-deactivated vehicles. For deactivated vehicles, the maximum speed is 90 kph.
With Shiftmatic
Model Engine Output
(kW) Top speeds (kph) with rear-axle ratio
4.182:1 4.364:1 4.727:1 5.1:1
Delivery Van with normal roof
Crafter 30/35 2.5 l BlueTDI 100 1542) 150
Crafter 503) 2.5 l BlueTDI 100 138 1352)
Delivery Van with high roof or super-high roof (super-high roof not for Crafter 30)
Crafter 30/35 2.5 l BlueTDI 100 1502) 146
Crafter 503) 2.5 l BlueTDI 100 134 1312)
With manual gearbox
Model Engine Output
(kW) Top speeds (kph) with rear-axle ratio
3.692:1 3.923:1 4.182:1 4.364:1 4.727:1 5.1:1
Delivery Van with normal roof or high roof
Crafter 30/35 2.0 l TDI 80 1491) 1472) 145 2.0 l TDI 100 1561) 1542) 152 2.0 l BiTDI 105 1581) 1562) 154 2.0 l BiTDI 120 1601) 1602) 157 Crafter 503) 2.0 l TDI 80 1351) 1332) 2.0 l BiTDI 105 1421) 1402) 2.0 l BiTDI 120 1541) 1522) 150 144
Delivery Van with super-high roof
Crafter 35 2.0 l TDI 80 1431) 1412) 139 2.0 l TDI 100 1491) 1472) 145 2.0 l BiTDI 105 1511) 1492) 147 2.0 l BiTDI 120 1581) 1562) 153 Crafter 503) 2.0 l TDI 80 1311) 1292) 2.0 l BiTDI 105 1371) 1352) 2.0 l BiTDI 120 1481) 1462) 144 138
Kombi with normal roof or high roof
Crafter 30/35 2.0 l TDI 80 1491) 1472) 145
2.0 l TDI 100 1561) 1542) 152
– Weights – The Crafter The Crafter – Weights –
Weights.
1) Equipment can result in an increase/decrease in the unladen weight and consequently affect the payload. Please consult your Volkswagen Commercial Vehicle partner. 2) Depending on the combination of engine, final drive ratio and tow bar. 3) Depending on the equipment, the front axle load limit may increase to 1,800 kg. This can affect the minimum payload. 4) Only possible in conjunction with tow bar with increased trailer load limit (optional extra). 5) There is no factory provision for a specific roof load on vehicles with a super high roof. For commercial use: in accordance with EU directive 3820/85, a tachograph is stipulated by law as of a gross train weight of 3.5 tonnes. Retrofitting of a tachograph is possible on all vehicles (standard at Crafter 50). The payloads listed here have been established allowing for factory options or other tailored solutions that are not included in the standard scope of delivery and services. The actual payload of a vehicle, which is calculated by the difference between the gross vehicle weight and the curb weight, can only be established by weighing the individual vehicle. Model/
Gross vehicle weight (kg)
Wheelbase
(mm) Unladen weight with driver
(kg)1)
Payload
(kg)1) Axle load limitfront/rear
(kg)
Gross train weight 12 % gradient
(kg)2)
Delivery Van BlueMotion with normal roof Crafter 30
3,000 3,250 1,904 – 2,075 1,096 – 925 1,650/1,800 5,000
Delivery Van with normal roof Crafter 30 3,000 3,250 1,904 – 2,319 1,096 – 681 1,650/1,800 5,000 Crafter 35 3,500 1,917 – 2,485 1,583 – 1,015 1,6503)/2,250 5,300 – 6,300 Crafter 30 3,000 3,665 1,972 – 2,319 1,028 – 681 1,650/1,800 5,000 Crafter 35 3,500 1,985 – 2,574 1,515 – 926 1,6503)/2,250 5,300 – 7,0004) Crafter 50 5,000 2,265 – 2,954 2,735 – 2,046 1,8505)/3,500 7,000 – 8,0004)
Delivery Van with high roof Crafter 30 3,000 3,665 2,008 – 2,319 992 – 681 1,650/1,800 5,000 Crafter 35 3,500 2,021 – 2,610 1,479 – 890 1,650 3)/2,250 5,300 – 7,0004) Crafter 50 5,000 2,301 – 2,990 2,699 – 2,010 1,8505)/3,500 7,000 – 8,0004) Crafter 35 3,500 4,325 2,155 – 2,772 1,345 – 728 1,650 3)/2,250 5,300 – 7,0004) Crafter 50 5,000 2,467 – 3,184 2,533 – 1,816 1,8505)/3,500 7,000 – 8,0004) Crafter 35 3,500 4,325 with overhang 2,207 – 2,819 1,293 – 681 1,650 3)/2,250 5,300 – 7,0004) Crafter 50 5,000 2,514 – 3,259 2,486 – 1,741 1,8505)/3,500 7,000 – 8,0004)
Delivery Van with super-high roof Crafter 35 3,500 3,665 2,057 – 2,646 1,443 – 854 1,6503)/2,250 5,300 – 7,0004) Crafter 50 5,000 2,337 – 3,026 2,663 – 1,974 1,8505)/3,500 7,000 – 8,0004) Crafter 35 3,500 4,325 2,182 – 2,799 1,318 – 701 1,6503)/2,250 5,300 – 7,0004) Crafter 50 5,000 2,494 – 3,211 2,506 – 1,789 1,8505)/3,500 7,000 – 8,0004) Crafter 35 3,500 4,325 with overhang 2,235 – 2,819 1,265 – 681 1,6503)/2,250 5,300 – 7,0004) Crafter 50 5,000 2,542 – 3,287 2,458 – 1,713 1,8505)/3,500 7,000 – 8,0004)
The Crafter – Weights –
– Weights – The Crafter
Weights.
Roof load limits Trailer nose weights
Model Roof load limit
(kg) Trailer nose weight(kg) With trailer nose limit (kg)
Delivery Van and Kombi
Normal roof 300 100 2,000
High roof 150 120 2,800/3,000
Super-high roof5) 140 3,500
1) Equipment can result in an increase/decrease in the unladen weight and consequently affect the payload. Please consult your Volkswagen Commercial Vehicle partner. 2) Depending on the combination of engine, final drive ratio and tow bar. 3) Depending on the equipment, the front axle load limit may increase to 1,800 kg. This can affect the minimum payload. 4) Only possible in conjunction with tow bar with increased trailer load limit (optional extra). 5) There is no factory provision for a specific roof load on vehicles with a super high roof For commercial use: in accordance with EU directive 3820/85, a tachograph is stipulated by law as of a gross train weight of 3.5 tonnes. Retrofitting of a tachograph is possible on all vehicles (standard at Crafter 50).
The actual payload of a vehicle, which is calculated by the difference between the gross vehicle weight and the curb weight, can only be established by weighing the individual vehicle. Model/
Gross vehicle weight (kg)
Wheelbase
(mm) Unladen weight with driver
(kg)1)
Payload
(kg)1) Axle load limitfront/rear
(kg)
Gross train weight 12 % gradient
(kg)2)
Kombi with normal roof Crafter 30 3,190 3,250 1,976 1,214 1,650 3)/1,800 5,190 Crafter 35 3,500 1,976 1,524 1,6503)/2,250 5,500 – 6,300 Crafter 30 3,190 3,665 2,005 1,185 1,650 3)/1,800 5,190 Crafter 35 3,500 2,028 1,472 1,6503)/2,250 5,500 – 7,0004)
Kombi with high roof Crafter 30 3,190 3,665 2,041 1,149 1,6503)/1,800 5,190 Crafter 35 3,500 2,064 1,436 1,6503)/2,250 5,500 – 7,0004) Crafter 35 3,500 4,325 2,219 1,281 1,6503)/2,250 5,500 – 7,0004)
– Dimensions and weights Crafter 4MOTION – The Crafter The Crafter – Dimensions and weights Crafter 4MOTION –
Dimensions and weights Crafter 4MOTION.
Model/
feature Crafter 35 4MOTION with Achleitner four-wheel drive(Delivery Van, Kombi) Crafter 50 4MOTION with Achleitner four-wheel drive (Delivery Van)
Wheelbase (mm) 3,250 3,665 4,325 4,325 with
overhang
3,665 4,325 4,325 with
overhang
Ground clearance front axle
(mm) 280 280 280 280 280 280 280
Ground clearance transfer case
(mm) 300 300 300 300 295 295 295
Ground clearance rear axle
(mm) from approx.240 –269 from approx.240 –269 from approx.240 –269 from approx.240 –269 from approx.246 –268 from approx.246 –268 from approx.246 –268
Axle load limit (front/rear) (kg) 1,800/2,250 1,800/2,250 1,800/2,250 1,800/2,250 2,000/3,500 2,000/3,500 2,000/3,500
Trailer weight braked (kg)/
unbraked (kg) 2,000 –2,800/ 750 2,000 –2,800/ 750 2,000 –2,800/ 750 2,000 –2,800/ 750 2,000 –3,500/ 750 2,000 –3,500/ 750 2,000 –3,500/ 750
Gross train weight at 12 %
gradient (kg) 5,300 – 6,300 5,300 – 7,000* 5,300 – 7,000* 5,300 – 7,000* 7,000 – 8,000* 7,000 – 8,000* 7,000 – 8,000* Wading depth (mm) 600 600 600 600 600 600 600 Chassis elevation 4 x 4 (mm) 100 100 100 100 100 100 100 Rear-axle ratio, ex factory/Achleitner 4.182/4.111 4.364 or 4.727 (optional)/ 4.375 or 4.857 (optional)
Auxiliary drive an auxiliary drive on the main gear is possible an auxiliary drive on the main gear is possible
*Only possible in conjunction with tow bar with increased trailer load limit (optional extra).
For commercial use: in accordance with EU directive 3820/85, a tachograph is stipulated by law as of a gross train weight of 3.5 tonnes. Retrofitting of a tachograph is possible on all vehicles (standard at Crafter 50).
The Crafter – Gross train weights and trailer load limits –
– Gross train weights and trailer load limits – The Crafter
Gross train weights and trailer load limits.
With manual gearbox
Model Engine
Out-put Gross train weight/trailer load limit (kg) with rear-axle ratio
(kW) 3.692:1 3.923:1 4.182:1 4.364:1 4.727:1 5.1:1
Delivery Van with normal roof, high roof or super-high roof (super-high roof not for Crafter 30)
Crafter 30 2.0 l TDI 80 5,0001)/2,0001) 5,0002)/2,0002) 5,000/2,000 2.0 l TDI 100 5,0001)/2,0001) 5,0002)/2,0002) 5,000/2,000 2.0 l BiTDI 105 5,0001)/2,0001) 5,0002)/2,0002) 5,000/2,000 2.0 l BiTDI 120 5,0001)/2,0001) 5,0002)/2,0002) 5,000/2,000 Crafter 35 2.0 l TDI 80 5,5001)/2,0001) 5,5002)/2,0002) 5,500/2,000 6,3003)/2,8003) 7,0003)/3,5003) 2.0 l TDI 100 5,5001)/2,0001) 5,5002)/2,0002) 5,500/2,000 6,3003)/2,8003) 7,0003)/3,5003) 2.0 l BiTDI 105 5,5001)/2,0001) 5,5002)/2,0002) 5,500/2,000 6,3003)/2,8003) 7,0003)/3,5003) 2.0 l BiTDI 120 5,3001)/2,0001) 5,5002)/2,0002) 5,500/2,000 6,3002), 3)/2,8002), 3) 6,3003)/2,8003) 7,0003)/3,5003) Crafter 50 2.0 l TDI 80 7,0001)/2,0001) 7,0002)/2,0002) 7,0001)/3,0001), 3) 7,0002)/3,0002), 3) 7,0001)/3,5001), 3) 7,0002)/3,5002), 3) 2.0 l BiTDI 105 7,0001)/2,0001) 7,0002)/2,0002) 7,0001)/3,0001), 3) 7,0002)/3,0002), 3) 7,0001)/3,5001), 3) 7,0002)/3,5002), 3) 2.0 l BiTDI 120 7,0001)/2,0001) 7,0002)/2,0002) 7,000/2,000 7,000/2,000 7,0001)/3,0001), 3) 7,5002), 3)/3,0002), 3) 8,0003)/3,0003) 8,0003)/3,0003) 7,0001)/3,5001), 3) 7,5002), 3)/3,5002), 3) 8,0003)/3,5003) 8,0003)/3,5003)
Kombi with normal roof or high roof
Crafter 30 2.0 l TDI 80 5,1901)/2,0001) 5,1902)/2,0002) 5,190/2,000 2.0 l TDI 100 5,1901)/2,0001) 5,1902)/2,0002) 5,190/2,000 2.0 l BiTDI 120 5,1901)/2,0001) 5,1902)/2,0002) Crafter 35 2.0 l TDI 80 5,5001)/2,0001) 5,5002)/2,0002) 5,500/2,000 6,3003)/2,8003) 7,0003)/3,5003) 2.0 l TDI 100 5,5001)/2,0001) 5,5002)/2,0002) 5,500/2,000 6,3003)/2,8003) 7,0003)/3,5003) 2.0 l BiTDI 120 5,5001)/2,0001) 5,5002)/2,0002) 6,3002), 3)/2,8002), 3) 1) Standard rear-axle ratio for Crafter Delivery Van BlueMotion (only for Crafter 30 with normal roof and 80 kW or 100 kW) as well as BlueMotion Technology. 2) Standard rear-axle ratio. 3) In conjunction with tow bar with increased trailer load limit (optional extra).
– Gross train weights and trailer load limits – The Crafter The Crafter – Gross train weights and trailer load limits –
Gross train weights and trailer load limits.
1) Standard rear-axle ratio. 2) In conjunction with tow bar with increased trailer load limit (optional extra). With Shiftmatic
Model Engine Output
(kW) Gross train weight/trailer load limit (kg) with rear-axle ratio
4.182:1 4.364:1 4.727:1 5.1:1
Delivery Van with normal roof, high roof or super-high roof (super-high roof not for Crafter 30)
Crafter 30 2.5 l BlueTDI 100 5,0001)/2,0001) 5,000/2,000 Crafter 35 2.5 l BlueTDI 100 5,5001)/2,0001) 5,500/2,000 6,3002)/2,8002) 7,0002)/3,5002) Crafter 50 2.5 l BlueTDI 100 7,000/2,000 7,0001)/2,0001) 7,000/3,0002) 7,0001)/3,0001), 2) 7,000/3,5002) 7,0001)/3,5001), 2)
The Crafter – Dimensional drawings –
– Dimensional drawings – The Crafter
Dimensional drawings.
All measurements listed are based on series vehicles. The height measurements listed here can differ by approx. ±40 mm depending on equipment. The vehicle drawings are not to scale. Crafter 30 Delivery Van BlueMotion with short wheelbase and normal roof/
Crafter 30/35 Delivery Van with short wheelbase and normal roof Crafter 30/35 Delivery Van with medium wheelbase and normal roof
1993 1000 3250 5240 990 2600 2426 670 2415 1650 1780 1350 1000 3665 5905 1240 1993 3265 2426 670 2415 1650 1780 1350 load compartment, volume 7.5 m3 load compartment, volume 9.0 m3 lateral sliding door, width/height 1,040/1,520 mm lateral sliding door, width/height 1,300/1,520 mm rear wing doors, width/height 1,565/1,540 mm rear wing doors, width/height 1,565/1,540 mm turning circle 12.3 m turning circle 13.6 m
Crafter 30/35 Delivery Van with medium wheelbase and high roof Crafter 35 Delivery Van with medium wheelbase and super-high roof
1993 1000 3665 5905 1240 3265 2426 670 2705 1940 1780 1350 3265 1000 3665 5905 1240 1993 670 2426 2940 1350 1780 2140 load compartment, volume 10.5 m3 load compartment, volume 11.5 m3 lateral sliding door, width/height 1,300/1,820 mm lateral sliding door, width/height 1,300/1,820 mm rear wing doors, width/height 1,565/1,840 mm rear wing doors, width/height 1,565/1,840 mm turning circle 13.6 m turning circle 13.6 m
Crafter 35 Delivery Van with long wheelbase and high roof Crafter 35 Delivery Van with long wheelbase and super-high roof
1000 4325 6940 1615 1993 4300 2426 670 2705 1940 1780 1350 1000 4325 6940 1615 1993 2426 670 4300 2940 2140 1350 1780 load compartment, volume 14.0 m3 load compartment, volume 15.5 m3 lateral sliding door, width/height 1,300/1,820 mm lateral sliding door, width/height 1,300/1,820 mm rear wing doors, width/height 1,565/1,840 mm rear wing doors, width/height 1,565/1,840 mm turning circle 15.6 m turning circle 15.6 m
– Dimensional drawings – The Crafter The Crafter – Dimensional drawings –
Dimensional drawings.
All measurements listed are based on series vehicles. The height measurements listed here can differ by approx. ±40 mm depending on equipment. The vehicle drawings are not to scale. Crafter 35 Delivery Van with long wheelbase, overhang
and high roof Crafter 35 Delivery Van with long wheelbase, overhang and super-high roof
1000 4325 7340 2015 2426 670 1993 4700 2705 1780 1350 1940 1000 4325 7340 2015 1993 2426 670 4700 2940 1780 1350 2140 load compartment, volume 15.5 m3 load compartment, volume 17.0 m3 lateral sliding door, width/height 1,300/1,820 mm lateral sliding door, width/height 1,300/1,820 mm rear wing doors, width/height 1,565/1,840 mm rear wing doors, width/height 1,565/1,840 mm turning circle 15.6 m turning circle 15.6 m
Crafter 50 Delivery Van with medium wheelbase and normal roof Crafter 50 Delivery Van with medium wheelbase and high roof
1000 3665 5905 1240 1993 3265 2426 725 2470 1650 1780 978 1993 1000 3665 5905 1240 3265 2426 725 2755 1940 1780 978 load compartment, volume 9.0 m3 load compartment, volume 10.5 m3 lateral sliding door, width/height 1,300/1,520 mm lateral sliding door, width/height 1,300/1,820 mm rear wing doors, width/height 1,565/1,540 mm rear wing doors, width/height 1,565/1,840 mm turning circle 13.6 m turning circle 13.6 m
Crafter 50 Delivery Van with medium wheelbase and super-high roof Crafter 50 Delivery Van with long wheelbase and high roof
3265 1000 3665 5905 1240 1993 725 2426 2990 2140 1780 978 1000 4325 6940 1615 1993 4300 2426 720 2755 1940 1780 978 load compartment, volume 11.5 m3 load compartment, volume 14.0 m3 lateral sliding door, width/height 1,300/1,820 mm lateral sliding door, width/height 1,300/1,820 mm rear wing doors, width/height 1,565/1,840 mm rear wing doors, width/height 1,565/1,840 mm turning circle 13.6 m turning circle 15.6 m
The Crafter – Dimensional drawings –
– Dimensional drawings – The Crafter
Dimensional drawings.
All measurements listed are based on series vehicles. The height measurements listed here can differ by approx. ±40 mm depending on equipment. The vehicle drawings are not to scale.
Crafter 50 Delivery Van with long wheelbase and super-high roof Crafter 50 Delivery Van with long wheelbase, overhang and high roof
1000 4325 6940 1615 1993 2426 720 4300 2990 1780 978 2140 1000 4325 7340 2015 1993 4700 2426 725 2755 1940 1780 978 load compartment, volume 15.5 m3 load compartment, volume 15.5 m3 lateral sliding door, width/height 1,300/1,820 mm lateral sliding door, width/height 1,300/1,820 mm rear wing doors, width/height 1,565/1,840 mm rear wing doors, width/height 1,565/1,840 mm turning circle 15.6 m turning circle 15.6 m
Crafter 50 Delivery Van with long wheelbase, overhang and super-high roof
1000 4325 7340 2015 1993 2426 725 4700 2990 1780 978 2140 load compartment, volume 17.0 m3 lateral sliding door, width/height 1,300/1,820 mm rear wing doors, width/height 1,565/1,840 mm turning circle 15.6 m
– Dimensional drawings – The Crafter The Crafter – Dimensional drawings –
Dimensional drawings.
All measurements listed are based on series vehicles. The height measurements listed here can differ by approx. ±40 mm depending on equipment. The vehicle drawings are not to scale.
Crafter 30/35 Kombi with short wheelbase and normal roof Crafter 30/35 Kombi with medium wheelbase and normal roof
1000 3250 5240 990 1993 2600 670 2426 2415 1650 1780 1350 1993 1000 3665 5905 3265 1240 670 2426 2415 1650 1780 1350 load compartment, volume 7.5 m3 load compartment, volume 9.0 m3 lateral sliding door, width/height 1,040/1,520 mm lateral sliding door, width/height 1,300/1,520 mm rear wing doors, width/height 1,565/1,540 mm rear wing doors, width/height 1,565/1,540 mm turning circle 12.3 m turning circle 13.6 m
Crafter 30/35 Kombi with medium wheelbase and high roof Crafter 35 Kombi with long wheelbase and high roof
1993 1000 3665 5905 1240 3265 2426 2705 1940 670 1780 1350 1000 4325 6940 1615 2426 670 1993 4300 2705 1940 1780 1350 load compartment, volume 10.5 m3 load compartment, volume 14.0 m3 lateral sliding door, width/height 1,300/1,820 mm lateral sliding door, width/height 1,300/1,820 mm rear wing doors, width/height 1,565/1,840 mm rear wing doors, width/height 1,565/1,840 mm turning circle 13.6 m turning circle 15.6 m
– Fuel consumptionand CO2 emissions for Crafter models with emission standard EEV (stricter than EURO V) – The Crafter – Fuel consumptionand COThe Crafter2 emissions for Crafter models with emission standard EEV (stricter than EURO V) –
Fuel consumption
and CO
2emissions for Crafter models with emission standard EEV
1)(stricter than EURO V).
With manual gearbox2), fuel consumption (litres/100 km) and combined CO
2 emissions (g/km), fuel tank capacity approx. 75 litres
Engine 2.0 l TDI (80 kW) 2.0 l BiTDI (105 kW) 2.0 l BiTDI (120 kW)
Rear-axle
ratio 4.182:1 4.364:13) 4.727:1 4.182:1 4.364:13) 4.727:1 3.692:1 3.923:13) 4.182:1
Crafter 30/35 Dropside Van
urban 10.4 – 10.6 10.3 – 11.3 11.5 9.5 – 10.2 10.1 – 11.1 11.5 8.6 – 9.0 9.0 – 9.2 9.5 – 10.2
extra-urban 6.9 – 7.9 7.8 – 8.3 8.7 7.2 – 7.8 7.6 – 8.1 8.7 6.9 – 7.7 7.0 – 7.9 7.2 – 7.8
combined 8.2 – 8.9 8.7 – 9.4 9.7 8.0 – 8.7 8.5 – 9.2 9.7 7.5 – 8.2 7.7 – 8.4 8.0 – 8.7
CO2 emissions
combined 216 – 234 229 – 247 255 210 – 229 224 – 242 255 197 – 216 203 – 221 210 – 229
Crafter 30/35 Dropside Van with start/stop system4)
urban 9.8 – 10.7 11.0 9.6 – 10.5 11.0 8.6 – 8.7 8.9 – 9.5
extra-urban 7.7 – 8.1 8.5 7.5 – 8.1 8.5 6.8 – 7.7 7.0 – 7.8
combined 8.4 – 9.1 9.4 8.2 – 8.9 9.4 7.4 – 8.1 7.7 – 8.4
CO2 emissions
combined 221 – 239 247 216 – 234 247 195 – 213 203 – 221
Crafter 30/35 Dropside Van with BlueMotion Technology
urban 9.4 – 10.0 8.9 – 9.5 7.8 – 8.5
extra-urban 7.0 – 7.9 7.0 – 7.8 6.9 – 7.5
combined 7.9 – 8.6 7.7 – 8.4 7.2 – 7.9
CO2 emissions
combined 208 – 227 203 – 221 189 – 208
1) “Enhanced Environmentally Friendly Vehicle”, the figures established are below the limits set by the EURO V emission standard. 2) Figures are not available for Crafter 50. 3) Standard rear-axle ratio. 4) Start/stop system available as an optional extra.
The fuel consumption and emission values listed here have been established in accordance with the measuring method stipulated (ECE-R 101). CO2 emissions arising from the production
and provision of fuel and/or other energy sources are not taken into consideration when determining the CO2 emissions in accordance with directive 1999/94/EC. These figures do not
refer to the particular vehicle and do not constitute part of the offer but are purely for comparison purposes between the various types of vehicle. In addition to the fuel efficiency of a vehicle, driving behaviour as well as other non-technical factors play a role in determining a vehicle’s fuel consumption and CO2 emissions. CO2 is the main greenhouse gas responsible
for global warming.
With Shiftmatic2), fuel consumption (litres/100 km) and combined CO
2 emissions (g/km), fuel tank capacity approx. 75 litres
Engine 2.5 l BlueTDI (100 kW)
Rear-axle
ratio 4.364:13) 4.727:1
Crafter 30/35 Dropside Van (except double cab with short wheelbase)
urban 10.6 10.9
extra-urban 8.7 8.9
combined 9.4 9.6
CO2 emissions
combined 247 253
Rear-axle ratio 4.111:1 (Crafter 4MOTION with
Achleitner four-wheel drive) Crafter 35 Dropside Van
urban 10,2
extra-urban 7,8
combined 8,7
CO2 emissions
The Crafter – Fuel consumption and CO2 emissions for Crafter models with emission standard Euro 5 –
– Fuel consumption and CO2 emissions for Crafter models with emission standard Euro 5 – The Crafter
Fuel consumption
and CO
2emissions for Crafter models with emission standard Euro 5.
1) Figures are not available for Crafter 50. 2) Standard rear-axle ratio. 3) Start/stop system available as an optional extra.
The fuel consumption and emission values listed here have been ascertained in accordance with the measuring method stipulated (the version of the EC directive 715/2007 which is currently valid). CO2 emissions arising from the production and provision of fuel and/or other energy sources are not taken into consideration when determining the CO2 emissions in
accordance with directive 1999/94/EC. These figures do not refer to a particular vehicle and do not constitute part of the offer but are purely for comparison purposes between the various types of vehicle. In addition to the fuel efficiency of a vehicle, driving behaviour as well as other non-technical factors play a role in determining a vehicle’s fuel consumption and CO2
emissions. CO2 is the main greenhouse gas responsible for global warming.
With manual gearbox1), fuel consumption (litres/100 km) and combined CO
2 emissions (g/km), fuel tank capacity approx. 75 litres
Engine 2.0 l TDI (80 kW) 2.0 l TDI (100 kW) 2.0 l BiTDI (120 kW)
Rear-axle
ratio 4.182:1 4.364:12) 4.727:1 4.182:1 4.364:12) 4.727:1 3.692:1 3.923:12) 4.182:1
Crafter 30/35 Dropside Van (only models with a maximum unladen weight of 2,815 kg incl. special bodies)
urban 9.8 – 10.7 10.2 – 10.8 11.5 9.8 – 10.7 10.2 – 10.8 11.5 8.4 – 9.0 8.8 – 9.2 9.6 – 10.3
extra-urban 7.3 – 7.9 7.9 – 8.6 8.7 7.3 – 7.9 7.9 – 8.6 8.7 7.0 – 7.7 7.1 – 7.9 7.1 – 7.8
combined 8.2 – 8.9 8.7 – 9.4 9.7 8.2 – 8.9 8.7 – 9.4 9.7 7.5 – 8.2 7.7 – 8.4 8.0 – 8.7
CO2 emissions
combined 216 – 234 229 – 247 255 216 – 234 229 – 247 255 197 – 216 203 – 221 210 – 229
Crafter 30/35 Dropside Van with start/stop system3) (only models with a maximum unladen weight of 2,815 kg incl. special bodies)
urban 9.7 – 10.3 11.0 9.7 – 10.3 11.0 8.2 – 8.7 9.2 – 9.6
extra-urban 7.7 – 8.4 8.5 7.7 – 8.4 8.5 7.0 – 7.7 6.8 – 7.7
combined 8.4 – 9.1 9.4 8.4 – 9.1 9.4 7.4 – 8.1 7.7 – 8.4
CO2 emissions
combined 221 – 239 247 221 – 239 247 195 – 213 203 – 221
Crafter 30/35 Dropside Van with BlueMotion Technology (only models with a maximum unladen weight of 2,815 kg incl. special bodies)
urban 9.5 – 10.0 9.5 – 10.0 7.8 – 8.5
extra-urban 7.1 – 7.7 7.1 – 7.7 6.8 – 7.5
combined 7.9 – 8.6 7.9 – 8.6 7.2 – 7.9
CO2 emissions
– Engines – The Crafter The Crafter – Engines –
Engines.
1) “Enhanced Environmentally Friendly Vehicle”, the figures established are below the limits set by the EURO V emission standard. 2) Not available for Crafter Chassis/Dropside Van with double cab and short wheelbase.
Diesel engines 2.0 l TDI engine (80 kW) 2.0 l TDI engine (100 kW)
(only with Crafter 30/35)
Mixture preparation/injection method common rail direct injection common rail direct injection
No. of cylinders 4 4
Cubic capacity, cm3 1,968 1,968
Output, kW at rpm 80 at 3,500 100 at 3,500
Max. torque, Nm/rpm 300/1,500 – 2,250 340/1,575 – 2,250
EU exhaust emission directive EEV1) according to regulation 2005/55/EC,
version 2008/74/EC or according to EC regulation 715/2007 Euro 5 respectively
according to EC regulation 715/2007 Euro 5
Diesel particulate filter (DPF) standard standard
6-speed manual gearbox standard standard
Rear-wheel drive standard standard
Type of fuel diesel, in accordance with DIN EN 590 diesel, in accordance with DIN EN 590
Diesel engines 2.5 l BlueTDI engine (100 kW)2) 2.0 l BiTDI engine (105 kW)
Mixture preparation/injection method common rail direct injection BiTurbo common rail direct injection
No. of cylinders 5 4
Cubic capacity, cm3 2,461 1,968
Output, kW at rpm 100 at 3,500 105 at 3,500
Max. torque, Nm/rpm 330/2,000 340/1,575 – 2,250
EU exhaust emission directive EEV1) according to regulation 2005/55/EC,
version 2008/74/EC
EEV1) according to regulation 2005/55/EC,
version 2008/74/EC
Diesel particulate filter (DPF) standard standard
6-speed manual gearbox/6-speed Shiftmatic –/standard standard/–
Rear-wheel drive standard standard
Type of fuel diesel, in accordance with DIN EN 590 diesel, in accordance with DIN EN 590
Diesel engine 2.0 l BiTDI engine (120 kW)
Mixture preparation/injection method BiTurbo common rail direct injection
No. of cylinders 4
Cubic capacity, cm3 1,968
Output, kW at rpm 105 at 3,500
Max. torque, Nm/rpm 340/1,575 – 2,250
EU exhaust emission directive EEV1) according to regulation 2005/55/EC,
version 2008/74/EC Diesel particulate filter (DPF) standard 6-speed manual gearbox standard/– Rear-wheel drive standard Type of fuel diesel, in accordance with DIN EN 590 engine speed [rpm] tor que [ Nm] output [kW] 80 kW 1000 2.0 l TDI (EEV/Euro 5) 140 80 60 40 20 250 200 150 100 50 300 100 120 2000 3000 4000 5000 300 Nm 80 kW engine speed [rpm] tor que [ Nm] output [kW] 100 kW 1000 2.0 l TDI (Euro 5) 140 80 60 40 20 250 200 150 100 50 300 400 350 100 120 2000 3000 4000 5000 340 Nm 100 kW engine speed [rpm] tor que [ Nm] output [kW] 100 kW 1000 2.5 l BlueTDI (EEV) 140 80 60 40 20 250 200 150 100 50 300 400 350 100 120 2000 3000 4000 5000 330 Nm 100 kW engine speed [rpm] tor que [ Nm] output [kW] 105 kW 1000 2.0 l BiTDI (EEV) 140 80 60 40 20 250 200 150 100 50 300 400 350 100 120 2000 3000 4000 5000 340 Nm 105 kW engine speed [rpm] tor que [ Nm] output [kW] 120 kW 1000 2.0 l BiTDI (EEV/Euro 5) 140 80 60 40 20 250 200 150 100 50 300 400 350 100 120 2000 3000 4000 5000 400 Nm 120 kW
The Crafter – Top speeds –
– Top speeds – The Crafter
Top speeds.
1) Standard rear-axle ratio with BlueMotion Technology. 2) Standard rear-axle ratio. 3) The maximum speeds shown here refer to non-deactivated vehicles. For deactivated vehicles, the maximum speed is 90 kph.
With Shiftmatic
Model Engine Output
(kW) Top speeds (kph) with rear-axle ratio
4.364:1 4.727:1 5.1:1
Dropside Van with single cab or double cab (except double cab with short wheelbase)
Crafter 30/35 2.5 l BlueTDI 100 1452) 141
Crafter 503) 2.5 l BlueTDI 100 133 1302)
With manual gearbox
Model Engine Output
(kW) Top speeds (kph) with rear-axle ratio
3.692:1 3.923:1 4.182:1 4.364:1 4.727:1 5.1:1
Dropside Van with single cab or double cab
Crafter 30/35 2.0 l TDI 80 1371) 1352) 133 2.0 l TDI 100 1421) 1402) 138 2.0 l BiTDI 105 1441) 1422) 140 2.0 l BiTDI 120 1521) 1502) 147 Crafter 503) 2.0 l TDI 80 1271) 1252) 2.0 l BiTDI 105 1331) 1312) 2.0 l BiTDI 120 1421) 1402) 138 132
– Weights – The Crafter The Crafter – Weights –
Weights.
1) Equipment can result in an increase/decrease in the unladen weight and consequently affect the payload. Please consult your Volkswagen Commercial Vehicle partner. 2) Depending on the combination of engine, final drive ratio and tow bar. 3) Depending on the equipment, the front axle load limit may increase to 1,800 kg. This can affect the minimum payload. 4) Only possible in conjunction with tow bar with increased trailer load limit (optional extra). 5) Depending on the equipment, the front axle load limit may increase to 2,000 kg. This can affect the minimum payload. For commercial use: in accordance with EU directive 3820/85, a tachograph is stipulated by law as of a gross train weight of 3.5 tonnes. Retrofitting of a tachograph is possible on all vehicles (standard at Crafter 50). The payload ranges illustrated here have been established bearing in mind equipment that can be selected or omitted, and other features which do not belong to the standard scope of delivery or standard specifications. A vehicle‘s actual payload, which results from calculating the difference between the gross vehicle weight and the unladen weight, can only determined by weighing the individual vehicle. Model/
Gross vehicle weight (kg)
Wheelbase
(mm) Unladen weight with driver
(kg)1)
from – to
Payload
(kg)1)
from – to
Axle load limit front/rear (kg)
Gross train weight 12 % gradient
(kg)2)
Chassis with single cab Crafter 30 3,000 3,250 1,651 – 2,066 1,349 – 934 1,650/1,800 5,000 Crafter 35 3,500 1,664 – 2,079 1,836 – 1,421 1,650 3)/2,250 5,300 – 6,300 Crafter 30 3,000 3,665 1,668 – 2,084 1,332 – 916 1,650/1,800 5,000 Crafter 35 3,500 1,681 – 2,097 1,819 – 1,403 1,650 3)/2,250 5,300 – 7,0004) Crafter 50 5,000 1,906 – 2,422 3,094 – 2,578 1,8505)/3,500 7,000 – 8,0004) Crafter 35 3,500 4,325 1,711 – 2,129 1,789 – 1,371 1,650 3)/2,250 5,300 – 7,0004) Crafter 50 5,000 1,944 – 2,462 3,056 – 2,538 1,8505)/3,500 7,000 – 8,0004)
Chassis with double cab Crafter 30 3,000 3,250 1,849 – 2,192 1,151 – 808 1,650/1,800 5,000 Crafter 35 3,500 1,862 – 2,277 1,638 – 1,223 1,6503)/2,250 5,300 – 6,300 Crafter 30 3,000 3,665 1,871 – 2,160 1,129 – 840 1,650/1,800 5,000 Crafter 35 3,500 1,884 – 2,300 1,616 – 1,200 1,6503)/2,250 5,300 – 7,0004) Crafter 50 5,000 2,127 – 2,633 2,873 – 2,367 1,850 5)/3,500 7,000 – 8,0004) Crafter 35 3,500 4,325 1,912 – 2,330 1,588 – 1,170 1,800/2,250 5,300 – 7,0004) Crafter 50 5,000 2,141 – 2,576 2,859 – 2,424 1,850 5)/3,500 7,000 – 8,0004)
The Crafter – Weights –
– Weights – The Crafter
Weights.
1) Equipment can result in an increase/decrease in the unladen weight and consequently affect the payload. Please consult your Volkswagen Commercial Vehicle partner. 2) Depending on the combination of engine, final drive ratio and tow bar. 3) Depending on the equipment, the front axle load limit may increase to 1,800 kg. This can affect the minimum payload. 4) Only possible in conjunction with tow bar with increased trailer load limit (optional extra). 5) Depending on the equipment, the front axle load limit may increase to 2,000 kg. This can affect the minimum payload. For commercial use: in accordance with EU directive 3820/85, a tachograph is stipulated by law as of a gross train weight of 3.5 tonnes. Retrofitting of a tachograph is possible on all vehicles (standard at Crafter 50). The payload ranges illustrated here have been established bearing in mind equipment that can be selected or omitted, and other features which do not belong to the standard scope of delivery or standard specifications. A vehicle‘s actual payload, which results from calculating the difference between the gross vehicle weight and the unladen weight, can only determined by weighing the individual vehicle. Model/
Gross vehicle weight (kg)
Wheelbase
(mm) Unladen weight with driver
(kg)1)
from – to
Payload
(kg)1)
from – to
Axle load limit front/rear (kg)
Gross train weight 12 % gradient
(kg)2)
Dropside Van with single cab Crafter 30 3,000 3,250 1,849 – 2,264 1,151 – 736 1,650/1,800 5,000 Crafter 35 3,500 1,862 – 2,227 1,638 – 1,223 1,650 3)/2,250 5,500 – 6,300 Crafter 30 3,000 3,665 1,898 – 2,314 1,102 – 686 1,650/1,800 5,000 Crafter 35 3,500 1,911 – 2,327 1,589 – 1,173 1,650 3)/2,250 5,500 – 7,0004) Crafter 50 5,000 2,207 – 2,723 2,793 – 2,277 1,8505)/3,500 7,000 – 8,0004) Crafter 35 3,500 4,325 1,990 – 2,408 1,510 – 1,092 1,650 3)/2,250 5,500 – 7,0004) Crafter 50 5,000 2,291 – 2,809 2,709 – 2,191 1,8505)/3,500 7,000 – 8,0004)
Dropside Van with double cab Crafter 30 3,000 3,250 2,007 – 2,350 993 – 650 1,650/1,800 5,000 Crafter 35 3,500 2,020 – 2,435 1,480 – 1,065 1,6503)/2,250 5,500 – 6,300 Crafter 30 3,000 3,665 2,061 – 2,350 939 – 650 1,650/1,800 5,000 Crafter 35 3,500 2,074 – 2,490 1,426 – 1,010 1,6503)/2,250 5,500 – 7,0004) Crafter 50 5,000 2,358 – 2,864 2,642 – 2,136 1,850 5)/3,500 7,000 – 8,0004) Crafter 35 3,500 4,325 2,145 – 2,563 1,355 – 937 1,800/2,250 5,500 – 7,0004) Crafter 50 5,000 2,434 – 2,869 2,566 – 2,131 1,850 5)/3,500 7,000 – 8,0004)
Roof load limits Trailer nose weights
Model Roof load limit
(kg) Trailer nose weight (kg) With trailer load limit (kg)
Chassis and Dropside Van
Single/double cab 100 100 2,000
120 2,800/3,000
– Dimensions and weights Crafter 4MOTION – The Crafter The Crafter – Dimensions and wights Crafter 4MOTION –
Dimensions and weights Crafter 4MOTION.
Model/
feature Crafter 35 4MOTION with Achleitner four-wheel drive(Chassis, Dropside Van) Crafter 50 4MOTION with Achleitner four-wheel drive (Chassis, Dropside Van)
Wheelbase (mm) 3,250 3,665 4,325 3,665 4,325
Ground clearance front axle
(mm) 280 280 280 280 280
Ground clearance transfer case
(mm) 300 300 300 295 295
Ground clearance rear axle
(mm) from approx. 240 –269 from approx. 240 –269 from approx. 240 –269 from approx. 246 –268 from approx. 246 –268
Axle load limit (front/rear) (kg) 1,800/2,250 1,800/2,250 1,800/2,250 2,000/3,500 2,000/3,500
Trailer weight braked (kg)/
unbraked (kg) 2,000 –2,800/ 750 2,000 –2,800/ 750 2,000 –2,800/ 750 2,000 –3,500/ 750 2,000 –3,500/ 750
Gross train weight at 12 %
gradient (kg) 5,300 – 6,300 5,300 –7,000* 5,300 – 7,000* 7,000 – 8,000* 7,000 – 8,000* Wading depth (mm) 600 600 600 600 600 Chassis elevation 4 x 4 (mm) 100 100 100 100 100 Rear-axle ratio, ex factory/Achleitner 4.182/4.111 4.364 or 4.727 (optional)/ 4.375 or 4.857 (optional)
Auxiliary drive an auxiliary drive on the main gear is possible an auxiliary drive on the main gear is possible
*Only possible in conjunction with tow bar with increased trailer load limit (optional extra).
For commercial use: in accordance with EU directive 3820/85, a tachograph is stipulated by law as of a gross train weight of 3.5 tonnes. Retrofitting of a tachograph is possible on all vehicles (standard at Crafter 50).
The Crafter – Gross train weights and trailer load limits –
– Gross train weights and trailer load limits – The Crafter
Gross train weights and trailer load limits.
With manual gearbox
Model Engine
Out-put Gross train weight/trailer load limit (kg) with rear-axle ratio
(kW) 3.692:1 3.923:1 4.182:1 4.364:1 4.727:1 5.1:1
Chassis /Dropside Van with single cab or double cab
Crafter 30 2.0 l TDI 80 5,0001)/2,0001) 5,0002)/2,0002) 5,000/2,000 2.0 l TDI 100 5,0001)/2,0001) 5,0002)/2,0002) 5,000/2,000 2.0 l BiTDI 105 5,0001)/2,0001) 5,0002)/2,0002) 5,000/2,000 2.0 l BiTDI 120 5,0001)/2,0001) 5,0002)/2,0002) 5,000/2,000 Crafter 35 2.0 l TDI 80 5,5001)/2,0001) 5,5002)/2,0002) 5,500/2,000 6,3002), 3)/2,8002), 3) 6,3003)/2,8003) 7,0002), 3)/3,5002), 3) 7,0003)/3,5003) 2.0 l TDI 100 5,5001)/2,0001) 5,5002)/2,0002) 5,500/2,000 6,3002), 3)/2,8002), 3) 6,3003)/2,8003) 7,0002), 3)/3,5002), 3) 7,0003)/3,5003) 2.0 l BiTDI 105 5,5001)/2,0001) 5,5002)/2,0002) 5,500/2,000 6,3002), 3)/2,8002), 3) 6,3003)/2,8003) 7,0002), 3)/3,5002), 3) 7,0003)/3,5003) 2.0 l BiTDI 120 5,3001)/2,0001) 5,5002)/2,0002) 5,500/2,000 6,3002), 3)/2,8002), 3) 6,3003)/2,8003) 7,0003)/3,5003) Crafter 50 2.0 l TDI 80 7,0001)/2,0001) 7,0002)/2,0002) 7,0001)/3,0001), 3) 7,0002)/3,0002), 3) 7,0001)/3,5001), 3) 7,0002)/3,5002), 3) 2.0 l BiTDI 105 7,0001)/2,0001) 7,0002)/2,0002) 7,0001)/3,0001), 3) 7,0002)/3,0002), 3) 7,0001)/3,5001), 3) 7,0002)/3,5002), 3) 2.0 l BiTDI 120 7,0001)/2,0001) 7,0002)/2,0002) 7,000/2,000 7,000/2,000 7,0001)/3,0001), 3) 7,5002), 3)/3,0002), 3) 8,0003)/3,0003) 8,0003)/3,0003) 7,0001)/3,5001), 3) 7,5002), 3)/3,5002), 3) 8,0003)/3,5003) 8,0003)/3,5003)
1) Standard rear-axle ratio with BlueMotion Technology. 2) Standard rear-axle ratio. 3) In conjunction with tow bar with increased trailer load limit (optional extra). 4) Only with Chassis.
With Shiftmatic
Model Engine
Out-put (kW)
Gross train weight/trailer load limit (kg) with rear-axle ratio
4.182:14) 4.364:1 4.727:1 5.1:1
Chassis /Dropside Van with single cab or double cab (except double cab with short wheelbase) Crafter 30 2.5 l BlueTDI 100 5,000/2,000 5,0002)/2,0002) 5,000/2,000 Crafter 35 2.5 l BlueTDI 100 5,500/2,000 5,5002)/2,0002) 5,500/2,000 6,3002), 3)/2,8002), 3) 6,3003)/2,8003) 7,0002), 3)/3,5002), 3) 7,0003)/3,5003) Crafter 50 2.5 l BlueTDI 100 7,000/2,000 7,0002)/2,0002) 7,000/3,0003) 7,0002)/3,0002), 3) 7,000/3,5003) 7,0002)/3,5002), 3)
– Dimensional drawings – The Crafter The Crafter – Dimensional drawings –
All measurements listed are based on series vehicles. The height measurements listed here can differ by approx. ±40 mm depending on equipment. The vehicle drawings are not to scale.
Dimensional drawings.
Crafter 30 Chassis with single cab and short wheelbase Crafter 30 Chassis with single cab and medium wheelbase
1000 3250 5300 1050 1990 2426 2360 1000 3665 5865 1200 1990 2426 2355 recommended exterior length for special body 3,050 mm recommended exterior length for special body 3,670 mm turning circle 12.3 m turning circle 13.5 m
Crafter 35 Chassis with single cab and short wheelbase Crafter 35 Chassis with single cab and medium wheelbase
2426 1000 3250 5300 1050 1990 2355 1000 3665 5865 1200 1990 2426 2345 recommended exterior length for special body 3,050 mm recommended exterior length for special body 3,670 mm turning circle 12.3 m turning circle 13.5 m
Crafter 35 Chassis with single cab and long wheelbase Crafter 50 Chassis with single cab and medium wheelbase
1000 4325 6675 1350 1990 2426 23 45 1000 3665 6082 1417 2426 1990 2380 recommended exterior length for special body 4,425 mm recommended exterior length for special body 3,845 mm turning circle 15.6 m turning circle 13.5 m
The Crafter – Dimensional drawings –
– Dimensional drawings – The Crafter
Dimensional drawings.
All measurements listed are based on series vehicles. The height measurements listed here can differ by approx. ±40 mm depending on equipment. The vehicle drawings are not to scale.
Crafter 50 Chassis with single cab and long wheelbase Crafter 30 Chassis with double cab and short wheelbase
1000 4325 6842 1517 2426 1990 2370 1990 1000 3250 5300 1050 2426 2375 recommended exterior length for special body 4,610 mm recommended exterior length for special body 2,160 mm turning circle 15.6 m turning circle 12.3 m
Crafter 30 Chassis with double cab and medium wheelbase Crafter 35 Chassis with double cab and short wheelbase
1000 3665 5865 1200 1990 2426 2365 1990 1000 3250 5300 1050 2426 2370 recommended exterior length for special body 2,770 mm recommended exterior length for special body 2,160 mm turning circle 13.5 m turning circle 12.3 m
Crafter 35 Chassis with double cab and medium wheelbase Crafter 35 Chassis with double cab and long wheelbase
1000 3665 5865 1200 1990 2426 2360 1000 4325 6675 1350 2426 1990 2350 recommended exterior length for special body 2,770 mm recommended exterior length for special body 3,440 mm turning circle 13.5 m turning circle 15.6 m
– Dimensional drawings – The Crafter The Crafter – Dimensional drawings –
Dimensional drawings.
All measurements listed are based on series vehicles. The height measurements listed here can differ by approx. ±40 mm depending on equipment. The vehicle drawings are not to scale.
Crafter 50 Chassis with double cab and medium wheelbase Crafter 50 Chassis with double cab and long wheelbase
1000 3665 6082 1417 1990 2426 2400 1000 4325 6842 1517 2426 1990 2385 recommended exterior length for special body 2,770 mm recommended exterior length for special body 3,610 mm turning circle 13.5 m turning circle 15.6 m
Crafter 30 Dropside Van with single cab and short wheelbase Crafter 30 Dropside Van with single cab and medium wheelbase
400 2090 1000 3250 5474 1224 2850 2426 2350 2030 965 400 2090 1000 3665 6024 1359 2426 3400 965 2030 2345 load area 5.8 m2 load area 6.9 m2 turning circle 12.3 m turning circle 13.5 m
Crafter 35 Dropside Van with single cab and short wheelbase Crafter 35 Dropside Van with single cab and medium wheelbase
400 2345 960 2030 2090 1000 3250 5474 1224 2426 2850 400 2345 960 2090 1000 3665 6024 1359 2030 3400 2426 load area 5.8 m2 load area 6.9 m2 turning circle 12.3 m turning circle 13.5 m
The Crafter – Dimensional drawings –
– Dimensional drawings – The Crafter
Dimensional drawings.
All measurements listed are based on series vehicles. The height measurements listed here can differ by approx. ±40 mm depending on equipment. The vehicle drawings are not to scale.
Crafter 35 Dropside Van with single cab and long wheelbase Crafter 50 Dropside Van with single cab and medium wheelbase
400 2330 965 2090 1000 4325 6924 1599 2426 2030 4300 400 2370 1025 1000 3665 6224 1559 2190 2130 3600 2675 load area 8.7 m2 load area 7.7 m2 turning circle 15.6 m turning circle 13.5 m
Crafter 50 Dropside Van with single cab and long wheelbase Crafter 30 Dropside Van with double cab and short wheelbase
400 2360 1030 1000 4325 6924 1599 2130 4300 2190 2675 400 2090 1000 3250 5554 1304 2426 2120 2365 2030 965 load area 9.2 m2 load area 4.3 m2 turning circle 15.6 m turning circle 12.3 m
Crafter 30 Dropside Van with double cab and medium wheelbase Crafter 35 Dropside Van with double cab and short wheelbase
400 965 2030 2090 1000 3665 6134 1469 2700 2426 2355 2360 960 2030 400 2090 1000 3250 5554 1304 2120 2426 load area 5.5 m2 load area 4.3 m2 turning circle 13.5 m turning circle 12.3 m
