Catalogue Drive systems

(1)

V 2.2 - 11 2015

Catalogue

Drive systems

(2)

(3)

I

I.3

Truss-rail ventilation 2.1 THG25R 2.2 THG42R 2.3 THG55R 2.4 THG60R 2.5 THG75R 2.6 THG25RK 2.7 THG42RK 2.8 THG55RK 2.9 THG75RK 2.10 THG55RK/THG75RK clamping set 2.11 THG25RKGC 2.12 THG55RKGC 2.13 THG75RKGC 2.14 THG25KG 2.15 Couplingset 27 mm 2.16 Couplingset 32 mm 2.17 Locking rings 2.18 Swinging ventilation 3.1

THG10S with gutter fork 3.2

THG10S with bracket 3.3

THG10SC (contra) with gutter fork 3.4

THG10SC (contra) with bracket 3.5

Auxiliary C-section with gutter fork 3.10

Auxiliary C-section with bracket 3.11

(4)

I

I.4

I

I.5

I

I.6 HOW TO FIND US

1. From Rotterdam:

From Rotterdam take the A13 in the direction of Den Haag. Take the exit to Den Haag-Zuid, Rijswijk. You are now on the A4 heading towards Den Haag-Zuid.

1. From Amsterdam:

Take the A4 in the direction of Den Haag (Zuid). 2. From the A4:

Take the exit Den Haag Zuid, Hoek van Holland, Wateringen.

(7)

I

I.7 LIST OF SYMBOLS

List of symbols

Symbol Unit Description

A [mm] Length

B [mm] Width

B1 [mm] Width

B1 [mm] Length of the tube

D [mm] Thickness or diameter D1 [mm] Thickness or diameter D2 [mm] Thickness or diameter D3 [mm] Thickness or diameter Db [-] Tube diameter F [N] Force F1 [N] Force H [mm] Height Ha [mm] Shaft centre Hb [mm] Tube centre i [-] Transmission ratio I [A] Current L [mm] Length L max [mm] Length maximum L min [mm] Length minimum

L1 [mm] Length L2 [mm] Length L3 [mm] Length L4 [mm] Length Lb [mm] Tube distance Lv [mm] Section size m [kg] Mass n [rev] Revolutions

n [rpm] Revolutions per minute

P [kW] Kilowatt

R [mm] Radius

s [mm/rev] Distance covered per revolution

S [mm] Stroke

St [mm] Truss width

T [Nm] Output torque

T1 [Nm] Input torque

U [V] Voltage

v [m/min] Distance covered per minute z [-] Number of teeth

(8)

I

I.8 APPLICATIONS OVERVIEW

Horticulture Horticulture Agriculture Agriculture Utility Utility

Ventilation Screening Hoisting _systems Ventilation _systemsRolling Hoisting _systems _ventilationNatural Daylight _control Solar

Truss-rail ventilation Swinging ventilation Continuous ridge ventilation Cabriolet ventilation Horizontal screening Tent screening Side wall screening Roof-roll screening Gauze hoisting system Heating tube lifting system Air inlet valves Ventilation panels Free range Storage spaces Climbing roll system Telescopic rollin

g system

Rail rollin

g system

Drink lines Feed lines Hanging platform Hoistable heating Roof ventilation Façade ventilation Horizontal louvres Roll-up sun screen Horizontal louvres Vertical louvres PV panels THG40 screen Wire screeening Hoistable panels

GW10 chain coupling x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x GW30 chain coupling x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x GW40 chain coupling x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x GW80 chain coupling x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x GW100 chain coupling x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x GW110S chain coupling x x x GW150S chain coupling x x x GXP10 coupling piece T x x x x x x x x GW40HB/HC chain coupling x x x x x x x x GW80HB/HC chain coupling x x x x x x x x GW100HB chain coupling x x x x x x x GW125HC chain coupling x x GW150HC chain coupling x x

GW10 cable winch drum L1, L2 x x x x x x x x x x GW10 sling winch drum LB1, x x x x x x x x x x GW30 cable winch drum L1, L2 x x x x x x x x x x GW30 sling winch drum LB1, x x x x x x x x x x GW40 cable winch drum L1, L2 x x x x x x x x x x GW40 sling winch drum LB1, x x x x x x x x x x GW2L cable winch drum L1 x x x x

GW10 TGA unit x x x x x GW20 TGA unit x x x x x GW10 high speed x x x x x GW20 high speed x x x x x GW30 high speed x x x x x GW40 high speed x x x x x THG25R x x x THG42R x x x THG55R x x x x x THG60R x x x THG75R x x x x x THG25RK x x x THG42RK x x x THG55RK x x x THG75RK x x x THG55RK/THG75RK clamping x x x THG25RKGC x x x THG55RKGC x x x THG75RKGC x x x THG25KG x x x

(9)

I

I.9 APPLICATIONS OVERVIEW

Horticulture Horticulture Agriculture Agriculture Utility Utility

Ventilation Screening Hoisting _systems Ventilation _systemsRolling _systemsHoisting _ventilationNatural Daylight _control Solar

g system

Rail rollin

g system

THG10SC (contra) with bracket x x THG24S with gutter fork x x THG24S with bracket x x THG49S with gutter fork x x THG49S with bracket x x Auxiliary C-section with gutter x x Auxiliary C-section with bracket x x Gutter fork x x GWK240/GWK400 worm gearbox x x x x x x x x x x x x x x x x x x GWK240/GWK400 worm gearbox x x x x x x x x x x x x x x x x x x THG30 unit x x x x x x x x x x THG30 economy x x x x x x THG30 distribution box x x x x

Window bracket set x x x x x x x x x x THG30 gear rack 2 mm x x x x x x

THG30 gear rack 3 mm x x x x x x x x x x THG30 bent internal toothing x x x x x x x x x x THG30 bent external toothing x x x x x x x x x x Right angled gearbox x x x x x x x x x x Sheave wheel for nests x x x x x x x x x x x

THG40 unit x x x x x THG40 unit (1:1) x x x THG40HD unit x x x x THG40 gear rack x x x x x THG40 HD gear rack x x x x THG40 weld-clearance joint x x x Coupling piece x x x x x

THG40 screen bracket set x x x THG40 clamping set x x x

THG40 locking ring x x x x x Slide bearing plate 1”, right x x x x x x x x x x x x x x x x

Slide bearing plate 1”, straight x x x x x x x x x x x x x x x x Slide bearing plate 5/4”, right x x x x x x x x x x

Slide bearing plate 5/4”, straight x x x x x x x x x x x Ball bearing plate x x x x x x x x x x x x x Mounting plate GW, straight x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x Mounting plate GW, right angled x x x x x x x x x x x x x x x x x x x x x x x x x x x x x Mountingseat GW80 x x x

Mountingseat GW150S Mountingseat GW220S

Clamping mounting plate x x Clamping mounting plate kolom x x

(10)

I

I.10 APPLICATIONS OVERVIEW

Horticulture Horticulture Agriculture Agriculture Utility Utility Ventilation Screening _systemsHoisting Ventilation _systemsRolling Hoisting _systems _ventilationNatural Daylight _control Solar

g system

Rail rollin

g system

Screen mounting plate (top) x x x Screen mounting plate (bottom) x x x

Mounting plate GXP10 bottom x x x x x x x Mounting plate GXP10 top x x x x x x x Mounting support x x

Telescopic arm TSP 40 x x x x x Winch drum double 5/4” x x x x x x

Cable ring 1” x x x x x x x x x x x

Shaft locking clip S20 x x x x x x x x Axle securing clip zk x x x x x x x x

GW10 motor cover

Universal joint x x x x x x x x x x Weld joint 1” x x x x x x

Coupling piece TSP40 GW x x x x

Bush joint 1” en 5/4” x x x x x x x x x x x x x x x x x x x Sleeve joint coupling x x x x x x x

Sleeve joint coupling prefab x x x x x x x x x Sleeve bolt coupling 1” x x x x x x x

Chain coupling 08B Z12 x x x x x x x x x x x x x x x x x x x Chain coupling 10B Z16 x x x x x x x x x x x x x x x x x x x x Chain coupling 10B Z16 S20 x x x x x x x

Chain coupling 10B Z16 ZK x x

Chain coupling 12B x x x x x x x x x x x x Tube bolt chain coupling 08B

Z12 x x x x x x x x x x x x x x x x x x x x x x Tube bolt chain coupling

Buis-buiskoppeling Coupling piece GXP10 - Ø32 x x x x Coupling piece GXP10 - Ø50 x x x x x x x Coupling piece GXP10 - Ø50 twin x x x x x x x Limit switch x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x I-DE x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x Potentiometer x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x Potentiometer tw sets x x x x x x x x x x x x x x x x x x x x x x x x GXP10 connecting set x x x x x x x Control boxes x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x Blue Control 100 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x Blue Control 250 Master x x x x x x

(11)

1

1.1 MOTOR GEARBOXES

GW SERIES

De Gier Drive Systems produce a complete range of robust and durable gear motors. The GW and GXP gear motors create a solid base for complete drive systems. The various versions of gear motors are used in ventilation, screening, heating tube lifting systems, and drink and feed lines in agriculture, greenhouse horticulture and non-residential construction.

Product characteristics of the GW and GXP gear motors:

• Self-braking due to the application of a worm-worm gear transmission. This means that, when the gear motor is stopped, the system stays in the desired position.

• Extremely silent during use, compact, powerful, reliable and maintenance-free. • Continuous operation S3-30% (continuous operation is limited to max. 25 minutes) • Torque range from 10 to 2,700Nm

• RPM range from 1.3 to 30 rotations/min

The GW and GXP gear motors have the following as standard: • II-I B Certificate for your CE label

• Integrated limit switch system with 2 main and 2 emergency stop switches ○ the GXP has a range of 0.2 to 37 revolutions of the output shaft ○ the GW has a range of 0.2 to 88 revolutions of the output shaft

○ the GW high speed gear motors with 15 and 30 revolutions/minute have a range of 1.0 to 1,400 revolutions of the output shaft

• The GW can be mounted on the floor and on the wall, the GXP only on the wall. • Electromotors IEC38, protection class IP55 in accordance with EN 600529. • Ready for mounting I-DE block for position feedback

• 2-K painted in De Gier Drive Systems Blue (RAL5009).

• Inbus connection in the electromotor shaft for the option of manual or cordless drill driver operation

• Including mounting instructions, motor installation materials, air-vent plug • Separate solid cardboard packaging with a GW or GXP identification label

The GW and GXP gear motors can optionally be fitted in the factory with electromotors which have: • a different voltage, frequency or protection class

• UL and CSA approval

The GW gear motor can optionally be fitted in the factory with position feedback to the climate control system which has:

• an Intelligent Digital Encoder (I-DE)

• potentiometer with the desired *feedback range and Ohm-value (* number of rotations of the output shaft from 0 to 100%)

(12)

(13)

1

1.3 MOTOR GEARBOXES

Motor gearboxes for

chain couplings

(14)

1

1.4 MOTOR GEARBOXES

GW10 CHAIN COUPLING

The GW10, with chain couplings on the driven shaft, has a number of applications, such as driving ventilation or screening systems.

As a standard the GW10 is fitted with a chain coupling set with a duplex chain according to DIN chain number 08B-2 or 10B-2. The sprocket wheel joint is available for a 1” (08B-2), 5/4” or 2” (both 10B-2) drive tubes. The motor gearbox can be mounted at the side or at the base.

The GW10 can optionally be fitted with a tube-bolt chain coupling set for 1” or 5/4” drive tubes. Electric motors with different voltages and/or frequencies or a higher protection class, for instance tropic winding, are available on request.

(15)

1

1.5 MOTOR GEARBOXES

GW10 CHAIN COUPLING

The table below lists the article numbers for the GW10 motor gearboxes, depending on the drive tube and the chain coupling set, including the chain and the sprocket wheel joint, supplied as standard.

Description

230/400 Volt • 3~ • 50 Hz Chain coupling

Article number T n P I L m Db type z [Nm] [rpm] [kW] [A] [mm] [kg] [-] - -GW10-1.3, 400V, 3~ 100 1.3 0.09 0.9/0.5 185 20 1” 08B-2 12 P.GW10.400.13.K100 GW10-1.3, 400V, 3~ 100 1.3 0.09 0.9/0.5 191 20 5/4” 10B-2 16 P.GW10.400.13.K125 GW10-1.3, 400V, 3~ 100 1.3 0.09 0.9/0.5 191 20 2” 10B-2 16 P.GW10.400.13.K200 GW10-2.6, 400V, 3~ 100 2.6 0.09 0.7/0.4 168 20 1” 08B-2 12 P.GW10.400.26.K100 GW10-2.6, 400V, 3~ 100 2.6 0.09 0.7/0.4 168 20 5/4” 10B-2 16 P.GW10.400.26.K125 GW10-2.6, 400V, 3~ 100 2.6 0.09 0.7/0.4 168 20 2” 10B-2 16 P.GW10.400.26.K200 GW10-5.2, 400V, 3~ 100 5.2 0.18 1.0/0.6 191 23 1” 08B-2 12 P.GW10.400.52.K100 GW10-5.2, 400V, 3~ 100 5.2 0.18 1.0/0.6 191 23 5/4” 10B-2 16 P.GW10.400.52.K125 GW10-5.2, 400V, 3~ 100 5.2 0.18 1.0/0.6 191 23 2” 10B-2 16 P.GW10.400.52.K200 Description

230 Volt • 1~ • 50 Hz Chain coupling

Article number T n P I L m Db type z [Nm] [rpm] [kW] [A] [mm] [kg] [-] - -GW10-1.3, 230V, 1~ 100 1.3 0.09 1.2 191 20 1” 08B-2 12 P.GW10.230.13.K100 GW10-1.3, 230V, 1~ 100 1.3 0.09 1.2 191 20 5/4” 10B-2 16 P.GW10.230.13.K125 GW10-1.3, 230V, 1~ 100 1.3 0.09 1.2 191 20 2” 10B-2 16 P.GW10.230.13.K200 GW10-2.6, 230V, 1~ 100 2.6 0.18 1.6 191 23 1” 08B-2 12 P.GW10.230.26.K100 GW10-2.6, 230V, 1~ 100 2.6 0.18 1.6 191 23 5/4” 10B-2 16 P.GW10.230.26.K125 GW10-2.6, 230V, 1~ 100 2.6 0.18 1.6 191 23 2” 10B-2 16 P.GW10.230.26.K200 GW10-5.2, 230V, 1~ 100 5.2 0.18 1.5 191 23 1” 08B-2 12 P.GW10.230.52.K100 GW10-5.2, 230V, 1~ 100 5.2 0.18 1.5 191 23 5/4” 10B-2 16 P.GW10.230.52.K125 GW10-5.2, 230V, 1~ 100 5.2 0.18 1.5 191 23 2” 10B-2 16 P.GW10.230.52.K200 Description

Article number T n P I L m Db type z [Nm] [rpm] [kW] [A] [mm] [kg] [-] - -GW10-1.3, 400V, 3~ 100 1.6 0.11 0.9/0.5 191 20 1” 08B-2 12 P.GW10.400.13.K100 GW10-1.3, 400V, 3~ 100 1.6 0.11 0.9/0.5 191 20 5/4” 10B-2 16 P.GW10.400.13.K125 GW10-1.3, 400V, 3~ 100 1.6 0.11 0.9/0.5 191 20 2” 10B-2 16 P.GW10.400.13.K200 GW10-2.6, 400V, 3~ 100 3.1 0.11 0.7/0.4 168 20 1” 08B-2 12 P.GW10.400.26.K100 GW10-2.6, 400V, 3~ 100 3.1 0.11 0.7/0.4 168 20 5/4” 10B-2 16 P.GW10.400.26.K125 GW10-2.6, 400V, 3~ 100 3.1 0.11 0.7/0.4 168 20 2” 10B-2 16 P.GW10.400.26.K200 GW10-5.2, 400V, 3~ 100 6.3 0.22 1.0/0.6 191 23 1” 08B-2 12 P.GW10.400.52.K100 GW10-5.2, 400V, 3~ 100 6.3 0.22 1.0/0.6 191 23 5/4” 10B-2 16 P.GW10.400.52.K125 GW10-5.2, 400V, 3~ 100 6.3 0.22 1.0/0.6 191 23 2” 10B-2 16 P.GW10.400.52.K200

(16)

1

1.6 MOTOR GEARBOXES

GW30 CHAIN COUPLING

The GW30, with chain couplings on the driven shaft, has a number of applications, such as driving ventilation or screening systems.

As a standard the GW30 is fitted with a chain coupling set with a duplex chain according to DIN chain number 10B-2. The sprocket wheel joint is available for 1”, 5/4” or 2” drive tubes. Attachment of the motor gearbox is possible at the side or the base. The GW30 can optionally be fitted with a tube-bolt chain coupling set for 1” or 5/4” drive tubes. Electric motors with different voltages and/or frequencies or a higher protection class, for instance tropic winding, are available on request.

(17)

1

1.7 MOTOR GEARBOXES

GW30 CHAIN COUPLING

Description

Article number T n P I L m Db type z [Nm] [rpm] [kW] [A] [mm] [kg] [-] - -GW30-1.3, 230V, 1~ 300 1.3 0.37 3.2 220 25 1” 10B-2 16 P.GW30.230.13.K100 GW30-1.3, 230V, 1~ 300 1.3 0.37 3.2 220 25 5/4” 10B-2 16 P.GW30.230.13.K125 GW30-1.3, 230V, 1~ 300 1.3 0.37 3.2 220 25 2” 10B-2 16 P.GW30.230.13.K200 GW30-2.6, 230V, 1~ 300 2.6 0.37 3.2 220 28 1” 10B-2 16 P.GW30.230.26.K100 GW30-2.6, 230V, 1~ 300 2.6 0.37 3.2 220 28 5/4” 10B-2 16 P.GW30.230.26.K125 GW30-2.6, 230V, 1~ 300 2.6 0.37 3.2 220 28 2” 10B-2 16 P.GW30.230.26.K200 GW30-5.2, 230V, 1~ 300 5.2 0.55 4.5 220 28 1” 10B-2 16 P.GW30.230.52.K100 GW30-5.2, 230V, 1~ 300 5.2 0.55 4.5 220 28 5/4” 10B-2 16 P.GW30.230.52.K125 GW30-5.2, 230V, 1~ 300 5.2 0.55 4.5 220 28 2” 10B-2 16 P.GW30.230.52.K200 Description

(18)

1

1.8 MOTOR GEARBOXES

GW40 CHAIN COUPLING

The GW40, with chain couplings on the driven shaft, has a number of applications, such as driving for ventilation or screening systems.

As a standard the GW40 is fitted with a chain coupling set with a duplex chain according to DIN chain number 10B-2. The sprocket wheel joint is available for 1”, 5/4” or 2” drive tubes. Attachment of the motor gearbox is possible at the side or base. The GW40 can optionally be fitted with a tube-bolt chain coupling set for 1” or 5/4” drive tubes. Electric motors with different voltages and/or frequencies, or a higher protection class, for instance tropic winding, are available on request.

(19)

1

1.9 MOTOR GEARBOXES

GW40 CHAIN COUPLING

Description

Article number T n P I L m Db type z [Nm] [rpm] [kW] [A] [mm] [kg] [-] - -GW40-1.3, 400V, 3~ 400 1,3 0,25 1,4/0,8 220 28 1” 10B-2 16 P.GW40.400.13.K100 GW40-1.3, 400V, 3~ 400 1,3 0,25 1,4/0,8 220 28 5/4” 10B-2 16 P.GW40.400.13.K125 GW40-1.3, 400V, 3~ 400 1,3 0,25 1,4/0,8 220 28 2” 10B-2 16 P.GW40.400.13.K200 GW40-2.6, 400V, 3~ 400 2,6 0,37 1,7/1,0 220 30 1” 10B-2 16 P.GW40.400.26.K100 GW40-2.6, 400V, 3~ 400 2,6 0,37 1,7/1,0 220 30 5/4” 10B-2 16 P.GW40.400.26.K125 GW40-2.6, 400V, 3~ 400 2,6 0,37 1,7/1,0 220 30 2” 10B-2 16 P.GW40.400.26.K200 GW40-5.2, 400V, 3~ 400 5,2 0,55 2,8/1,6 220 30 1” 10B-2 16 P.GW40.400.52.K100 GW40-5.2, 400V, 3~ 400 5,2 0,55 2,8/1,6 220 30 5/4” 10B-2 16 P.GW40.400.52.K125 GW40-5.2, 400V, 3~ 400 5,2 0,55 2,8/1,6 220 30 2” 10B-2 16 P.GW40.400.52.K200 Description

Article number T n P I L m Db type z [Nm] [rpm] [kW] [A] [mm] [kg] [-] - -GW40-1.3, 230V, 1~ 400 1,3 0,37 3,2 220 28 1” 10B-2 16 P.GW40.230.13.K100 GW40-1.3, 230V, 1~ 400 1,3 0,37 3,2 220 28 5/4” 10B-2 16 P.GW40.230.13.K125 GW40-1.3, 230V, 1~ 400 1,3 0,37 3,2 220 28 2” 10B-2 16 P.GW40.230.13.K200 GW40-2.6, 230V, 1~ 400 2,6 0,55 4,8 242 33 1” 10B-2 16 P.GW40.230.26.K100 GW40-2.6, 230V, 1~ 400 2,6 0,55 4,8 242 33 5/4” 10B-2 16 P.GW40.230.26.K125 GW40-2.6, 230V, 1~ 400 2,6 0,55 4,8 238 33 2” 10B-2 16 P.GW40.230.26.K200 GW40-5.2, 230V, 1~ 400 5,2 0,75 6,0 242 34 1” 10B-2 16 P.GW40.230.52.K100 GW40-5.2, 230V, 1~ 400 5,2 0,75 6,0 242 34 5/4” 10B-2 16 P.GW40.230.52.K125 GW40-5.2, 230V, 1~ 400 5,2 0,75 6,0 242 34 2” 10B-2 16 P.GW40.230.52.K200 Description

Article number T n P I L m Db type z [Nm] [rpm] [kW] [A] [mm] [kg] [-] - -GW40-1.3, 400V, 3~ 400 1,6 0,3 1,4/0,8 220 28 1” 10B-2 16 P.GW40.400.13.K100 GW40-1.3, 400V, 3~ 400 1,6 0,3 1,4/0,8 220 28 5/4” 10B-2 16 P.GW40.400.13.K125 GW40-1.3, 400V, 3~ 400 1,6 0,3 1,4/0,8 220 28 2” 10B-2 16 P.GW40.400.13.K200 GW40-2.6, 400V, 3~ 400 3,1 0,44 1,7/1,0 220 30 1” 10B-2 16 P.GW40.400.26.K100 GW40-2.6, 400V, 3~ 400 3,1 0,44 1,7/1,0 220 30 5/4” 10B-2 16 P.GW40.400.26.K125 GW40-2.6, 400V, 3~ 400 3,1 0,44 1,7/1,0 220 30 2” 10B-2 16 P.GW40.400.26.K200 GW40-5.2, 400V, 3~ 400 6,3 0,65 2,8/1,6 220 30 1” 10B-2 16 P.GW40.400.52.K100 GW40-5.2, 400V, 3~ 400 6,3 0,65 2,8/1,6 220 30 5/4” 10B-2 16 P.GW40.400.52.K125 GW40-5.2, 400V, 3~ 400 6,3 0,65 2,8/1,6 220 30 2” 10B-2 16 P.GW40.400.52.K200

(20)

1

1.10 MOTOR GEARBOXES

GW80 CHAIN COUPLING

As a standard the GW80 is fitted with a chain coupling set with a duplex chain according to DIN chain number 10B-2. The sprocket wheel joint is available for 1”, 5/4” or 2” drive tubes. Attachment of the motor gearbox is possible at the side or base. The GW80 can optionally be fitted with a tube-bolt chain coupling set for 1” or 5/4” drive tubes. Electric motors with different voltages and/or frequencies, or a higher protection class, for instance tropic winding, are available on request.

(21)

1

1.11 MOTOR GEARBOXES

GW80 CHAIN COUPLING

Description

(22)

1

1.12 MOTOR GEARBOXES

GW100 CHAIN COUPLING

As a standard the GW100 is fitted with a chain coupling set with a duplex chain according to DIN chain number 12B-2. The sprocket wheel joint is available for 5/4” or 2” drive tubes. Attachment of the motor gearbox is possible at the side or base. Electric motors with different voltages and/or frequencies, or a higher protection class, for instance tropic winding, are available on request.

(23)

1

1.13 MOTOR GEARBOXES

GW100 CHAIN COUPLING

Description

Article number T n P I L m Db type z [Nm] [rpm] [kW] [A] [mm] [kg] [-] - -GW100-2.6, 400V, 3~ 1000 2.6 0.75 3.8/2.2 242 39 5/4” 12B-2 18 P.GW100.400.26.K125 GW100-2.6, 400V, 3~ 1000 2.6 0.75 3.8/2.2 242 39 2” 12B-2 18 P.GW100.400.26.K200 Description

Article number

T n P I L m Db type z

[Nm] [rpm] [kW] [A] [mm] [kg] [-] -

-GW100-2.6, 400V, 3~ 1000 3.1 0.90 3.8/2.2 242 39 5/4” 12B-2 18 P.GW100.400.26.K125

(24)

(25)

1

1.15 MOTOR GEARBOXES

Motor gearboxes for

screening systems

(26)

1

1.16 MOTOR GEARBOXES

GW110S CHAIN COUPLING

The GW110S, with chain couplings on the driven shaft is used for driving screening systems.

As a standard the GW110S is fitted with a chain coupling set with a duplex chain according to DIN chain no. 12B-2. The sprocket wheel joint is available for 2” drive tubes. The motor gearbox can be attached to the greenhouse by its base.

Electric motors with different voltages and/or frequencies, or a higher protection class, for instance tropic winding, are available on request.

(27)

1

1.17 MOTOR GEARBOXES

GW110S CHAIN COUPLING

The table below lists the article numbers for the GW110S motor gearboxes, depending on the drive tube and the chain coupling set, including the chain and the sprocket wheel joint, supplied as standard.

Description

Article number

[Nm] [rpm] [kW] [A] [mm] [kg] [-] -

-GW110S-4.0, 400V, 3~ 1100 4.0 1.1 5.4/3.1 242 38 2” 12B-2 18 P.GW110S.400.40.K200

Description

Article number

[Nm] [rpm] [kW] [A] [mm] [kg] [-] -

(28)

1

1.18 MOTOR GEARBOXES

GW150S CHAIN COUPLING

As a standard the GW150S is fitted with a chain coupling set with a duplex chain according to DIN chain no. 12B-2. The sprocket wheeljoint is available for 2” drive tubes. The motor gearbox can be attached to the greenhouse by its base.

(29)

1

1.19 MOTOR GEARBOXES

GW150S CHAIN COUPLING

Description

Article number

[Nm] [rpm] [kW] [A] [mm] [kg] [-] -

-GW150S-4.0, 400V, 3~ 1500 4.0 1.5 7.1/4.1 280 40 2” 12B-2 18 P.GW150S.400.40.K200

Description

Article number

[Nm] [rpm] [kW] [A] [mm] [kg] [-] -

(30)

1

1.20 MOTOR GEARBOXES

GW220S CHAIN COUPLING

(31)

1

1.21 MOTOR GEARBOXES

GW220S CHAIN COUPLING

Description

Article number

[Nm] [rpm] [kW] [A] [mm] [kg] [-] -

-GW220S-4.0, 400V, 3~ 2200 4.0 2.2 8.3-4.8 316 66 2” 12B-2 18 P.GW220S.400.40.K200

Description

Article number

[Nm] [rpm] [kW] [A] [mm] [kg] [-] -

(32)

1

1.22 MOTOR GEARBOXES

GW270S CHAIN COUPLING

(33)

1

1.23 MOTOR GEARBOXES

GW270S CHAIN COUPLING

Description

Article number

[Nm] [rpm] [kW] [A] [mm] [kg] [-] -

-GW270S-4.0, 400V, 3~ 2700 4.0 3.0 11/6.4 316 78 2” 16B-2 16 P.GW270S.400.40.K200

Description

Article number

[Nm] [rpm] [kW] [A] [mm] [kg] [-] -

(34)

1

1.24 MOTOR GEARBOXES

GXP10 COUPLING PIECE T

The GXP10 coupling piece T has a number of applications, such as roll screen systems and side roll ventilation systems.

The GXP10 has a double drive shaft of Ø19.5 mm and can be attached to a roll tube of Ø32 mm or Ø50 mm by means of a coupling. A Ø32 mm tube can guide the system. Standard executed with couplings for Ø50 mm tube and with guidance for Ø32 mm tube.

(35)

1

1.25 MOTOR GEARBOXES

GXP10 COUPLING PIECE T

The table below lists the article numbers of the GXP10 motor gearboxes, depending on the roll-tube dimension.

Electric motors with tropical winding are adjusted to operating in high humidity surroundings.

Description

230/400 Volt • 3~ • 50 Hz Roll-up tube

Article number

T n P I m D

[Nm] [rpm] [kW] [A] [kg] [mm]

GXP10-4.0, 400V, 3~ tropical winding 100 4.0 0.18 1.2/0.7 11 - P.GXP10.400.40.KBS.T GXP10-4.0, 400V, 3~ tropical winding 100 4.0 0.18 1.2/0.7 11 Ø32 x 1,5 P.GXP10.400.40.KBS32.T GXP10-4.0, 400V, 3~ tropical winding 100 4.0 0.18 1.2/0.7 11 Ø50 single track P.GXP10.400.40.KBS50.T GXP10-4.0, 400V, 3~ tropical winding 100 4.0 0.18 1.2/0.7 11 Ø50 double track P.GXP10.400.40.KBS50.02.T

Description

230 Volt • 1~ • 50 Hz Roll-up tube

Article number

T n P I m D

[Nm] [rpm] [kW] [A] [kg] [mm]

GXP10-4.0, 230V, 1~ tropical winding 100 4.0 0.22 1.8 11 - P.GXP10.230.40.2.KBS.T GXP10-4.0, 230V, 1~ tropical winding 100 4.0 0.22 1.8 11 Ø32 x 1,5 P.GXP10.230.40.2.KBS32.T GXP10-4.0, 230V, 1~ tropical winding 100 4.0 0.22 1.8 11 Ø50 single track P.GXP10.230.40.2.KBS50.T GXP10-4.0, 230V, 1~ tropical winding 100 4.0 0.22 1.8 11 Ø50 double track P.GXP10.400.40.2.KBS50.02.T

Description

277/480 Volt • 3~ • 60 Hz Roll-up tube

Article number

T n P I m D

[Nm] [rpm] [kW] [A] [kg] [mm]

GXP10-4.0, 400V, 3~ tropical winding 100 4.8 0.22 1.2/0.7 11 - P.GXP10.400.40.KBS.T GXP10-4.0, 400V, 3~ tropical winding 100 4.8 0.22 1.2/0.7 11 Ø32 x 1,5 P.GXP10.400.40.KBS32.T GXP10-4.0, 400V, 3~ tropical winding 100 4.8 0.22 1.2/0.7 11 Ø50 single track P.GXP10.400.40.KBS50.T GXP10-4.0, 400V, 3~ tropical winding 100 4.8 0.22 1.2/0.7 11 Ø50 double track P.GXP10.400.40.KBS50.02.T

(36)

(37)

1

1.27 MOTOR GEARBOXES

GW10 CHAIN COUPLING

Motor gearboxes for

hoisting systems

(38)

1

1.28 MOTOR GEARBOXES

GW40HB/HC CHAIN COUPLING

The GW40HB, with chain couplings on the driven shaft, has a number of applications, such as hoisting heating tubes and feed- and drink lines.

The GW40HC, with chain couplings on the driven shaft, has a number of applications in the chrysanthemums, freesias and lilies, such as hoisting gauze heating systems. Girders are installed above the cultivation beds and fitted with wire gauze and heating tubes. The gauze is hoisted through the crop which gives a significant resistance. As a standard the motor gearboxes for hoisting are fitted with a chain coupling set with a duplex chain. The sprocket wheel joint is available for 1”, 5/4” or 2” drive tubes. Attachment of the motor gearbox is possible at the side or base.

(39)

1

1.29 MOTOR GEARBOXES

GW40HB/HC CHAIN COUPLING

The table below lists the article numbers for the GW40HB/HC motor gearboxes, depending on the drive tube and the chain coupling set, including the chain and the sprocket wheel joint, supplied as standard.

Description

Article number T n P I L m Db type z [Nm] [rpm] [kW] [A] [mm] [kg] [-] - -GW40HB-2.6, 400V, 3~ 400 2.6 0.37 1.7/1.0 266 32 1” 10B-2 16 P.GW40HB.400.26.K100 GW40HB-2.6, 400V, 3~ 400 2.6 0.37 1.7/1.0 266 32 5/4” 10B-2 16 P.GW40HB.400.26.K125 GW40HB-2.6, 400V, 3~ 400 2.6 0.37 1.7/1.0 266 32 2” 10B-2 16 P.GW40HB.400.26.K200 Description

Article number T n P I L m Db type z [Nm] [rpm] [kW] [A] [mm] [kg] [-] - -GW40HC-2.6, 400V, 3~ 400 2.6 0.37 1.7/1.0 220 30 1” 10B-2 16 P.GW40HC.400.26.K100 GW40HC-2.6, 400V, 3~ 400 2.6 0.37 1.7/1.0 220 30 5/4” 10B-2 16 P.GW40HC.400.26.K125 GW40HC-2.6, 400V, 3~ 400 2.6 0.37 1.7/1.0 220 30 2” 10B-2 16 P.GW40HC.400.26.K200 Description

Article number T n P I L m Db type z [Nm] [rpm] [kW] [A] [mm] [kg] [-] - -GW40HC-2.6, 400V, 3~ 400 3.1 0.44 1.7/1.0 220 30 1” 10B-2 16 P.GW40HC.400.26.K100 GW40HC-2.6, 400V, 3~ 400 3.1 0.44 1.7/1.0 220 30 5/4” 10B-2 16 P.GW40HC.400.26.K125 GW40HC-2.6, 400V, 3~ 400 3.1 0.44 1.7/1.0 220 30 2” 10B-2 16 P.GW40HC.400.26.K200

Hoisting Systems Safety

When using the hoist, do not allow people to stand under or close to suspended loads. Observe all national standards and guidelines, and safety and accident prevention regulations. Do not use the hoist to lift loads in areas in which people are present. If higher safety requirements are applicable to the lifting of loads, such as when hoisting heating tubes or drink and feed lines, the equipment should only be used with a fall prevention system.

(40)

1

1.30 MOTOR GEARBOXES

GW80HB/HC CHAIN COUPLING

The GW80HC, with chain couplings on the driven shaft, has a number of applications in the chrysanthemums, freesias and lilies, such as hoisting gauze heating systems. Girders are installed above the cultivation beds and fitted with wire gauze and heating tubes. The gauze is hoisted through the crop which gives a significant resistance. As a standard the motor gearboxes for hoisting are fitted with a chain coupling set with a duplex chain. The sprocket wheel joint is available for 1”, 5/4” or 2” drive tubes. Attachment of the motor gearbox is possible at the side or base.

(41)

1

1.31 MOTOR GEARBOXES

GW80HB/HC CHAIN COUPLING

The table below lists the article numbers for the GW80HB/HC motor gearboxes, depending on the drive tube and the chain coupling set, including the chain and the sprocket wheel joint, supplied as standard.

Description

Article number T n P I L m Db type z [Nm] [rpm] [kW] [A] [mm] [kg] [-] - -GW80HC-2.6, 400V, 3~ 800 2.6 0.55 2.6/1.5 218 32 1” 10B-2 16 P.GW80HC.400.26.K100 GW80HC-2.6, 400V, 3~ 800 2.6 0.55 2.6/1.5 218 32 5/4” 10B-2 16 P.GW80HC.400.26.K125 GW80HC-2.6, 400V, 3~ 800 2.6 0.55 2.6/1.5 218 32 2” 10B-2 16 P.GW80HC.400.26.K200 Description

Article number T n P I L m Db type z [Nm] [rpm] [kW] [A] [mm] [kg] [-] - -GW80HC-2.6, 400V, 3~ 800 3.1 0.66 2.6/1.5 218 32 1” 10B-2 16 P.GW80HC.400.26.K100 GW80HC-2.6, 400V, 3~ 800 3.1 0.66 2.6/1.5 218 32 5/4” 10B-2 16 P.GW80HC.400.26.K125 GW80HC-2.6, 400V, 3~ 800 3.1 0.66 2.6/1.5 218 32 2” 10B-2 16 P.GW80HC.400.26.K200

(42)

1

1.32 MOTOR GEARBOXES

GW100HB CHAIN COUPLING

As a standard the GW100HB is fitted with a chain coupling set with a duplex chain according to DIN chain number 12B-2. The sprocket wheel joint is available for 5/4” or 2” drive tubes. Attachment of the motor gearbox is possible at the side or base. Electric motors with different voltages and/or frequencies, or a higher protection class, for instance tropic winding, are available on request.

(43)

1

1.33 MOTOR GEARBOXES

GW100HB CHAIN COUPLING

The table below lists the article numbers for the GW100HB motor gearboxes, depending on the drive tube and the chain coupling set, including the chain and the sprocket wheel joint, supplied as standard.

Description

Article number T n P I L m Db type z [Nm] [rpm] [kW] [A] [mm] [kg] [-] - -GW100HB-2.6, 400V, 3~ 1000 2.6 0.75 3.8/2.2 298 38 5/4” 12B-2 18 P.GW100HB.400.26.K125 GW100HB-2.6, 400V, 3~ 1000 2.6 0.75 3.8/2.2 298 38 2” 12B-2 18 P.GW100HB.400.26.K200 Description

Article number

[Nm] [rpm] [kW] [A] [mm] [kg] [-] -

-GW100HB-2.6, 400V, 3~ 1000 3.1 0.90 3.8/2.2 298 38 5/4” 12B-2 18 P.GW100HB.400.26.K125

GW100HB-2.6, 400V, 3~ 1000 3.1 0.90 3.8/2.2 298 38 2” 12B-2 18 P.GW100HB.400.26.K200

(44)

1

1.34 MOTOR GEARBOXES

GW125HC CHAIN COUPLING

The GW125HC, with chain couplings on the driven shaft, has a number of applications in the chrysanthemums, freesias and lilies, such as hoisting gauze heating systems. Girders are installed above the cultivation beds and fitted with wire gauze and heating tubes. The gauze is hoisted through the crop which gives a significant resistance. As a standard the GW125HC is fitted with a chain coupling set with a duplex chain according to DIN chain number 12B-2. The sprocket wheel joint is available for 5/4” or 2” drive tubes. Attachment of the motor gearbox is possible at the side or base. Electric motors with different voltages and/or frequencies, or a higher protection class, for instance tropic winding, are available on request.

(45)

1

1.35 MOTOR GEARBOXES

GW125HC CHAIN COUPLING

The table below lists the article numbers for the GW125HC motor gearboxes, depending on the drive tube and the chain coupling set, including the chain and the sprocket wheel joint, supplied as standard.

Description

Article number T n P I L m Db type z [Nm] [rpm] [kW] [A] [mm] [kg] [-] - -GW125HC-2.6, 400V, 3~ 1250 2.6 0.88 4.5/2.6 238 38 5/4” 12B-2 16 P.GW125HC.400.26.K125 GW125HC-2.6, 400V, 3~ 1250 2.6 0.88 4.5/2.6 238 38 2” 12B-2 16 P.GW125HC.400.26.K200 GW125HC-2.6, 400V, 3~

Without limit switch 1250 2.6 0.88 4.5/2.6 238 38 5/4” 12B-2 16 P.GW125HC.400.26.K125.GE

GW125HC-2.6, 400V, 3~

Without limit switch 1250 2.6 0.88 4.5/2.6 238 38 2” 12B-2 16 P.GW125HC.400.26.K200.GE

Description

GW125HC-2.6, 400V, 3~

(46)

1

1.36 MOTOR GEARBOXES

GW150HC CHAIN COUPLING

The GW150HC, with chain couplings on the driven shaft, has a number of applications in the chrysanthemums, freesias and lilies, such as hoisting gauze heating systems. Girders are installed above the cultivation beds and fitted with wire gauze and heating tubes. The gauze is hoisted through the crop which gives a significant resistance. As a standard the GW150HC is fitted with a chain coupling set with a duplex chain according to DIN chain number 12B-2. The sprocket wheel joint is available for 5/4” or 2” drive tubes. Attachment of the motor gearbox is possible at the side or base. Electric motors with different voltages and/or frequencies, or a higher protection class, for instance tropic winding, are available on request.

(47)

1

1.37 MOTOR GEARBOXES

GW150HC CHAIN COUPLING

The table below lists the article numbers for the GW150HC motor gearboxes, depending on the drive tube and the chain coupling set, including the chain and the sprocket wheel joint, supplied as standard.

Description

GW150HC-2.6, 400V, 3~

Description

GW150HC-2.6, 400V, 3~

(48)

(49)

1

1.39 MOTOR GEARBOXES

Motor gearboxes with

winch drum

(50)

1

1.40 MOTOR GEARBOXES

GW10 CABLE WINCH DRUM L1, L2

The GW10 with a cable drum on the driven shaft has various applications, such as the hoisting of feeder lines and the opening of vents.

As a standard the GW10 is fitted with a single or double cable winch drum (diameter 50 mm). Attachment of the motor gearbox is possible at the side or base.

Safety

Warning!

The steel cable must be wound at least three times around the drum before any load is applied. See the winch tables in the appendices for use in combination with various systems.

Single

(51)

1

1.41 MOTOR GEARBOXES

GW10 CABLE WINCH DRUM L1, L2

The table below lists the article numbers for the GW10 motor gearboxes, depending on the drum version.

The maximum gross tractive force is based on a Ø 5 mm cable wound directly on the 50 mm winch drum. When more than one layer is wound on the drum and cables are stacked, the available tractive force will decrease, depending on the structure of the layers! See the winch tables in the appendices.

Description

230/400 Volt • 3~ • 50 Hz Winch drum

Article number

T n P I L m D Load type Max. gross load

[Nm] [rpm] [kW] [A] [mm] [kg] [mm] [N] GW10-1.3, 400V, 3~, Ø50 single winch 100 1.3 0.09 0.9/0.5 191 23 50 1000 = F1 P.GW10.400.13.L1 GW10-2.6, 400V, 3~, Ø50 single winch 100 2.6 0.09 0.7/0.4 168 23 50 1000 = F1 P.GW10.400.26.L1 GW10-5.2, 400V, 3~, Ø50 single winch 100 5.2 0.18 1.0/0.6 191 25 50 1000 = F1 P.GW10.400.52.L1 GW10-1.3, 400V, 3~, Ø50 double winch 100 1.3 0.09 0.9/0.5 191 23 50 3000 = 2 x F2 (2 x 1500) P.GW10.400.13.L2 GW10-2.6, 400V, 3~, Ø50 double winch 100 2.6 0.09 0.7/0.4 168 23 50 3000 = 2 x F2 (2 x 1500) P.GW10.400.26.L2 GW10-5.2, 400V, 3~, Ø50 double winch 100 5.2 0.18 1.0/0.6 191 25 50 3000 = 2 x F2 (2 x 1500) P.GW10.400.52.L2 Description

230 Volt * 1~ * 50 Hz Winch drum

Article number

[Nm] [rpm] [kW] [A] [mm] [kg] [mm] [N] GW10-1.3, 230V, 1~, Ø50 single winch 100 1.3 0.09 1.2 191 23 50 1000 = F1 P.GW10.230.13.L1 GW10-2.6, 230V, 1~, Ø50 single winch 100 2.6 0.18 1.6 191 25 50 1000 = F1 P.GW10.230.26.L1 GW10-5.2, 230V, 1~, Ø50 single winch 100 5.2 0.18 1.5 191 25 50 1000 = F1 P.GW10.230.52.L1 GW10-1.3, 230V, 1~, Ø50 double winch 100 1.3 0.09 1.2 191 23 50 3000 = 2 x F2 (2 x 1500) P.GW10.230.13.L2 GW10-2.6, 230V, 1~, Ø50 double winch 100 2.6 0.18 1.6 191 25 50 3000 = 2 x F2 (2 x 1500) P.GW10.230.26.L2 GW10-5.2, 230V, 1~, Ø50 double winch 100 5.2 0.18 1.5 191 25 50 3000 = 2 x F2 (2 x 1500) P.GW10.230.52.L2 Description

277/480 Volt • 3~ • 60Hz Winch drum

Article number

[Nm] [rpm] [kW] [A] [mm] [kg] [mm] [N] GW10-1.3, 400V, 3~, Ø50 single winch 100 1.6 0.11 0.9/0.5 191 23 50 1000 = F1 P.GW10.400.13.L1 GW10-2.6, 400V, 3~, Ø50 single winch 100 3.1 0.11 0.7/0.4 168 23 50 1000 = F1 P.GW10.400.26.L1 GW10-5.2, 400V, 3~, Ø50 single winch 100 6.3 0.22 1.0/0.6 191 25 50 1000 = F1 P.GW10.400.52.L1 GW10-1.3, 400V, 3~, Ø50 double winch 100 1.6 0.11 0.9/0.5 191 23 50 3000 = 2 x F2 (2 x 1500) P.GW10.400.13.L2 GW10-2.6, 400V, 3~, Ø50 double winch 100 3.1 0.11 0.7/0.4 168 23 50 3000 = 2 x F2 (2 x 1500) P.GW10.400.26.L2 GW10-5.2, 400V, 3~, Ø50 double winch 100 6.3 0.22 1.0/0.6 191 25 50 3000 = 2 x F2 (2 x 1500) P.GW10.400.52.L2

(52)

1

1.42 MOTOR GEARBOXES

GW10 SLING WINCH DRUM LB1, LB2

The GW10 with a winch drum on the driven shaft has various applications, such as the hoisting of feeder lines and the opening of vents.

As a standard the GW10 is fitted with a single or double winch drum (diameter 50 mm). Attachment of the motor gearbox is possible at the side or base.

Safety

Warning!

Slings must be wound at least twice around the drum before any load is applied. See the winch tables in the appendices for use in combination with various systems.

Catalogue Drive systems

Catalogue

Drive systems

I

I.3

TABLE OF CONTENTS

I

I.4

TABLE OF CONTENTS

I

I.5

TABLE OF CONTENTS

I

I.6

HOW TO FIND US

I

I.7

LIST OF SYMBOLS

I

I.8

APPLICATIONS OVERVIEW

I

I.9

APPLICATIONS OVERVIEW

I

I.10

APPLICATIONS OVERVIEW

1

1.1

MOTOR GEARBOXES

GW SERIES

1

1.3

MOTOR GEARBOXES

Motor gearboxes for

chain couplings

1

1.4

MOTOR GEARBOXES

GW10 CHAIN COUPLING

1

1.5

MOTOR GEARBOXES

GW10 CHAIN COUPLING

1

1.6

MOTOR GEARBOXES

GW30 CHAIN COUPLING

1

1.7

MOTOR GEARBOXES

GW30 CHAIN COUPLING

1

1.8

MOTOR GEARBOXES

GW40 CHAIN COUPLING

1

1.9

MOTOR GEARBOXES

GW40 CHAIN COUPLING

1

1.10

MOTOR GEARBOXES

GW80 CHAIN COUPLING

1

1.11

MOTOR GEARBOXES

GW80 CHAIN COUPLING

1

1.12

MOTOR GEARBOXES

GW100 CHAIN COUPLING

1

1.13

MOTOR GEARBOXES

GW100 CHAIN COUPLING

1

1.15

MOTOR GEARBOXES

Motor gearboxes for