4G LTE Integration Training

(1)

www.huawei.com

英文标题:40-47pt 副标题:26-30pt 字体颜色:反白内部使用字体 : FrutigerNext LT Medium 外部使用字体 : Arial 中文标题:35-47pt 字体:黑体副标题:24-28pt 字体颜色:反白字体:细黑体

4G LTE Integration

(2)

英文标题:32-35pt 颜色: R153 G0 B0 内部使用字体 : FrutigerNext LT Medium 外部使用字体 : Arial 中文标题:30-32pt 颜色: R153 G0 B0 字体:黑体英文正文:20-22pt 子目录 (2-5级) :18pt 颜色:黑色内部使用字体 : FrutigerNext LT Regular 外部使用字体 : Arial 中文正文:18-20pt 子目录(2-5级):18pt 颜色:黑色字体:细黑体配色参考方案：建议同一页面内不超过四种颜色，以下是 13组配色方案，同一页面内只选择一组使用。（仅供参考）伙伴的标志放在右上角.

Types of site connectivity:

Page 2

eNodeB

GE/FE Cable Fiber Cable

MW RTN900

GPON MDU (SmartAx)

Fiber Cable

Exchange OLT

1- GPON site.

2- Microwave site.

(3)

英文标题:32-35pt 颜色: R153 G0 B0 内部使用字体 : FrutigerNext LT Medium 外部使用字体 : Arial 中文标题:30-32pt 颜色: R153 G0 B0 字体:黑体英文正文:20-22pt 子目录 (2-5级) :18pt 颜色:黑色内部使用字体 : FrutigerNext LT Regular 外部使用字体 : Arial 中文正文:18-20pt 子目录(2-5级):18pt 颜色:黑色字体:细黑体配色参考方案：建议同一页面内不超过四种颜色，以下是 13组配色方案，同一页面内只选择一组使用。（仅供参考）

GPON connection

4G

3G

2G

For 4G , 3G and 2G use FE/GE cable.

(4)

Microwave Connection

Page 4

MW RTN950

(5)

Microwave Connection

EM6F Card of RTN950

4G

3G

2G

For 4G and 3G use LC to LC Fiber cable

(6)

DF Connection

Page 6

Connect Fiber cable to ODF in

Exchange site to the assigned

Port ( you can know which port

from JISOW sheet ).

(7)

LTE BBU connection

or DF

(8)

LTE 4G Integration

Main Job on site:



Use WEBLMT to login the eNodeB



Add the OM link and check the link status

Steps Of Job:



Use WEBLMT to login the eNodeB



Use the Ethernet cable to connect to ETH port of LMPT board.



Configure the IP 192.168.0.2 on laptop.



Use IE Browser and visit the website:



http://192.168.0.49/



Username：admin



Password： admin123



You must have

JISOW

sheet for IPs and VLAN

(9)

1. SET DHCPSW: SWITCH=DISABLE;

2. SET ETHPORT to modify as the picture below:

GPON : Port Attribute = Copper

(10)

3. DSP ETHPORT: SN=7, SBT=BASE_BOARD; To check port status

DSP ETHPORT Result

---

Cabinet No. = 0 Subrack No. = 0 Slot No. = 7

Subboard Type = Base Board Port No. = 0

Port Attribute = Copper Port Status = Up Physical Layer Status = Up

Maximum Transmission Unit(byte) = 1500 ARP Proxy = Enable Flow Control = Open

MAC Address = 707B-E8C5-8B9A Loopback Status = No Loop

In Loopback Mode or Not = No Ethernet OAM 3AH Flag = Disable Number of RX Packets(packet) = 444334 Number of RX Bytes(byte) = 79380405 Number of RX CRC Error Packets(packet) = 4

RX Traffic(byte/s) = 257 Number of TX Packets(packet) = 215850 Number of TX Bytes(byte) = 40290597 TX Traffic(byte/s) = 146

Local Configuration Negotiation Mode = Automatic Negotiation Local Actual Negotiation Mode = Automatic Negotiation

Local Speed = 1000M Local Duplex = Full Duplex Peer Actual Negotiation Mode = Unknown Peer Speed = 1000M Peer Duplex = Unknown Number of IPs = 2

IP Address List = 10.226.5.193 255.255.255.252 = 10.140.10.193 255.255.255.252 (Number of results = 1)

(11)

4. ADD DEVIP:;

As picture below:

5. ADD VLANMAP:;

0 O&M Host IP in JISOW

From JISOW

VLAN ID (OaM) in JISOW

O&M DGW in JISOW

From JISOW

(12)

6. ADD OMCH:;

Page 12

O&M Host IP in JISOW

O&M DGW in JISOW

From JISOW

(13)

7. Ping:;

Tow destination:



PING from Local IP to GW IP

(14)



Ping Result must be as follow:

(15)

8. Copy the Script Below To Batch section and press GO and

wait till finish.

(16)

9. ADD GPS: SN=7, CABLETYPE=COAXIAL, CABLE_LEN=45,

PRI=1;

10. SET CLKSYNCMODE: CLKSYNCMODE=TIME;

Page 16

Select Time

(17)

11. DSP GPS: GN=0;

* Make sure the GPS Card State is Normal; And the GPS Satellites

Traced is larger than 8.

(18)

12. STR VSWRTEST:;

Be sure all VSWR values below 140

(19)



At Last when every things Ok Call integration Team to make

complete integration remotely after confirm to you status is

ok you can leave site.

(20)

Some Cases



Ethernet Port wrong configured.



Only can ping to GW but you cannot ping to Peer IP (M2000).

(21)