Vintage-PH1. Barebone System

(1)

(2)

i i i i i i i i i i C o p y r i g h t © 2 0 0 5 A S U S T e K C O M P U T E R I N C . A l l R i g h t s R e s e r v e d . C o p y r i g h t © 2 0 0 5 A S U S T e K C O M P U T E R I N C . A l l R i g h t s R e s e r v e d . C o p y r i g h t © 2 0 0 5 A S U S T e K C O M P U T E R I N C . A l l R i g h t s R e s e r v e d . C o p y r i g h t © 2 0 0 5 A S U S T e K C O M P U T E R I N C . A l l R i g h t s R e s e r v e d . C o p y r i g h t © 2 0 0 5 A S U S T e K C O M P U T E R I N C . A l l R i g h t s R e s e r v e d .

No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).

Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing.

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR

INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL,

INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Products and corporate names appearing in this manual may or may not be registered

trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.

(3)

i i i i i ii i i i i i i i i

Chapter 1: System Introduction

1.1 Welcome! ... 1-2 1.2 Front panel ... 1-2 1.3 Rear panel ... 1-4 Voltage selector ... 1-6 1.4 Internal components ... 1-7

Chapter 2:

Basic Installation

(4)

i v i v i v i v i v

Chapter 3:

Starting up

3.1 Installing an operating system ... 3-2 3.2 Powering up ... 3-2 3.3 Support CD information ... 3-2 3.3.1 Running the support CD ... 3-3 3.3.2 Utilities menu ... 3-4 3.2.3 ASUS Contact information ... 3-5

Chapter 4:

Motherboard Info

4.1 Introduction ... 4-2 4.2 Motherboard layout ... 4-2 4.3 Jumpers ... 4-3 4.4 Connectors ... 4-6

Chapter 5:

BIOS Information

(5)

(6)

v i v i v i v i v i

Notices

Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and

• This device must accept any interference received including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with

manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Canadian Department of Communications Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

This class B digital apparatus complies with Canadian ICES-003. This class B digital apparatus complies with Canadian ICES-003. This class B digital apparatus complies with Canadian ICES-003. This class B digital apparatus complies with Canadian ICES-003. This class B digital apparatus complies with Canadian ICES-003.

W A R N I N G ! W A R N I N G ! W A R N I N G ! W A R N I N G !

(7)

v i i v i iv i i v i i v i i

Safety information

Electrical safety

• To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system.

• When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected.

• If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.

Operation safety

• Before installing devices into the system, carefully read all the documentation that came with the package.

• Before using the product, make sure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately.

• To avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry.

• Avoid dust, humidity, and temperature extremes. Do not place the product in any area where it may become wet. Place the product on a stable surface.

• If you encounter technical problems with the product, contact a qualified service technician or your retailer.

L i t h i u m - I o n B a t t e r y W a r n i n g L i t h i u m - I o n B a t t e r y W a r n i n gL i t h i u m - I o n B a t t e r y W a r n i n g L i t h i u m - I o n B a t t e r y W a r n i n g L i t h i u m - I o n B a t t e r y W a r n i n g C A U T I O N C A U T I O NC A U T I O N C A U T I O N

C A U T I O N: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the

manufacturerís instructions. V O R S I C H T

V O R S I C H TV O R S I C H T V O R S I C H T

V O R S I C H T: Explosionsgetahr bei unsachgemäßen Austausch der Batterie. Ersatz nur durch denselben oder einem vom Hersteller empfohlenem ähnljchen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.

(8)

v i i i v i i i v i i i v i i i v i i i

About this guide

Audience

This guide provides general information and installation instructions about the ASUS Vintage-PH1 barebone system. This guide is intended for

experienced users and integrators with hardware knowledge of personal computers.

How this guide is organized

This guide contains the following parts: 1 .

1 . 1 . 1 .

1 . C h a p t e r 1 : S y s t e m i n t r o d u c t i o nC h a p t e r 1 : S y s t e m i n t r o d u c t i o nC h a p t e r 1 : S y s t e m i n t r o d u c t i o nC h a p t e r 1 : S y s t e m i n t r o d u c t i o nC h a p t e r 1 : S y s t e m i n t r o d u c t i o n

This chapter gives a general description of the ASUS Vintage-PH1. The chapter lists the system features, including introduction on the front and rear panel, and internal components.

2 . 2 . 2 . 2 .

2 . C h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o n

This chapter provides step-by-step instructions on how to install components in the system.

3 . 3 . 3 . 3 .

3 . C h a p t e r 3 : S t a r t i n g u pC h a p t e r 3 : S t a r t i n g u pC h a p t e r 3 : S t a r t i n g u pC h a p t e r 3 : S t a r t i n g u pC h a p t e r 3 : S t a r t i n g u p

This chapter helps you power up the system and install drivers and utilities from the support CD.

4 . 4 . 4 . 4 .

4 . C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o nC h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o nC h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o nC h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o nC h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n

This chapter gives information about the motherboard that comes with the system. This chapter includes the motherboard layout, jumper settings, and connector locations.

5 . 5 . 5 . 5 .

5 . C h a p t e r 5 : B I O S i n f o r m a t i o nC h a p t e r 5 : B I O S i n f o r m a t i o nC h a p t e r 5 : B I O S i n f o r m a t i o nC h a p t e r 5 : B I O S i n f o r m a t i o nC h a p t e r 5 : B I O S i n f o r m a t i o n

(9)

i x i xi x i xi x

Conventions used in this guide

W A R N I N G : W A R N I N G : W A R N I N G : W A R N I N G :

W A R N I N G : Information to prevent injury to yourself when trying to complete a task.

C A U T I O N : C A U T I O N : C A U T I O N : C A U T I O N :

C A U T I O N : Information to prevent damage to the components when trying to complete a task.

I M P O R T A N T : I M P O R T A N T : I M P O R T A N T : I M P O R T A N T :

I M P O R T A N T : Instructions that you MUST follow to complete a task.

N O T E : N O T E : N O T E : N O T E :

N O T E : Tips and additional information to aid in completing a task.

Where to find more information

Refer to the following sources for additional information and for product and software updates.

1 . 1 . 1 . 1 .

1 . A S U S W e b s i t e sA S U S W e b s i t e sA S U S W e b s i t e sA S U S W e b s i t e sA S U S W e b s i t e s

The ASUS websites worldwide provide updated information on ASUS hardware and software products. Refer to the ASUS contact

information. 2 . 2 . 2 . 2 . 2 . O p t i o n a l D o c u m e n t a t i o nO p t i o n a l D o c u m e n t a t i o nO p t i o n a l D o c u m e n t a t i o nO p t i o n a l D o c u m e n t a t i o nO p t i o n a l D o c u m e n t a t i o n

(10)

xxxxx

System package contents

Check your Vintage-PH1 system package for the following items.

If any of the items is damaged or missing, contact your retailer immediately. I t e m d e s c r i p t i o n I t e m d e s c r i p t i o nI t e m d e s c r i p t i o n I t e m d e s c r i p t i o nI t e m d e s c r i p t i o n 1 . 1 .1 . 1 .1 . A S U S V i n t a g e - P H 1 b a r e b o n e s y s t e mA S U S V i n t a g e - P H 1 b a r e b o n e s y s t e mA S U S V i n t a g e - P H 1 b a r e b o n e s y s t e mA S U S V i n t a g e - P H 1 b a r e b o n e s y s t e m withA S U S V i n t a g e - P H 1 b a r e b o n e s y s t e m • ASUS motherboard

(11)

A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1

Chapter 1

System introduction

This chapter gives a general description of the ASUS

Vintage-PH1. The chapter lists the system features including

(12)

1 - 2 1 - 2 1 - 2 1 - 2 1 - 2 C h a p t e r 1 : S y s t e m i n t r o d u c t i o nC h a p t e r 1 : S y s t e m i n t r o d u c t i o nC h a p t e r 1 : S y s t e m i n t r o d u c t i o nC h a p t e r 1 : S y s t e m i n t r o d u c t i o nC h a p t e r 1 : S y s t e m i n t r o d u c t i o n

1.1 Welcome!

Thank you for choosing the ASUS Vintage-PH1!

The ASUS Vintage-PH1 is an all-in-one barebone system with a versatile home entertainment feature.

The system comes in a stylish mini-tower casing and powered by the ASUS motherboard that supports the Intel®_Pentium®_{4 processor in the 775-land}

package with 800 MHz FSB and up to 2 GB system memory.

With audio capabilities, extensive connectivity, and Gigabit LAN capability, the Vintage-PH1 is designed to deliver cutting edge technology for your computing and multimedia needs.

1.2 Front panel

The front panel includes the optical drive(s), floppy disk drive slot, power button, and several I/O ports are located at the front panel.

(13)

1 - 3 1 - 31 - 3 1 - 3 1 - 3 A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1 1 . 1 .1 .

1 .1 . T w o e m p t y 5 . 2 5 - i n c h b a y sT w o e m p t y 5 . 2 5 - i n c h b a y sT w o e m p t y 5 . 2 5 - i n c h b a y s. These bays are for IDE optical drives.T w o e m p t y 5 . 2 5 - i n c h b a y sT w o e m p t y 5 . 2 5 - i n c h b a y s 2 .

2 .2 .

2 .2 . H a r d d i s k d r i v e b a yH a r d d i s k d r i v e b a yH a r d d i s k d r i v e b a y. This door covers a hard disk drive.H a r d d i s k d r i v e b a yH a r d d i s k d r i v e b a y 3 .

3 .3 .

3 .3 . F l o p p y d r i v e d o o rF l o p p y d r i v e d o o rF l o p p y d r i v e d o o r. This drive is for 1.44MB, 3.5-inch floppy disk.F l o p p y d r i v e d o o rF l o p p y d r i v e d o o r 4 .

4 .4 .

4 .4 . R e s e t b u t t o nR e s e t b u t t o nR e s e t b u t t o n. Press this button to reboot the system withoutR e s e t b u t t o nR e s e t b u t t o n turning off the power.

5 . 5 .5 .

5 .5 . P o w e r b u t t o nP o w e r b u t t o nP o w e r b u t t o n. Press this button to turn the system on.P o w e r b u t t o nP o w e r b u t t o n 6 .

6 .6 .

6 .6 . H e a d p h o n e p o r tH e a d p h o n e p o r tH e a d p h o n e p o r t. This Line In (green) port connects a headphoneH e a d p h o n e p o r tH e a d p h o n e p o r t with a stereo mini-plug.

7 . 7 .7 .

7 .7 . M i c r o p h o n e p o r tM i c r o p h o n e p o r tM i c r o p h o n e p o r t. This Mic (pink) port connects a microphone.M i c r o p h o n e p o r tM i c r o p h o n e p o r t 8 .

8 .8 .

8 .8 . U S B 2 . 0 p o r t sU S B 2 . 0 p o r t sU S B 2 . 0 p o r t s. These Universal Serial Bus 2.0 (USB 2.0) ports areU S B 2 . 0 p o r t sU S B 2 . 0 p o r t s available for connecting USB 2.0 devices such as a mouse, printer, scanner, camera, PDA, and others.

9 . 9 .9 .

(14)

1.3 Rear panel

The system rear panel includes the power connector and several I/O ports that allow convenient connection of devices.

1 . 1 . 1 . 1 .

1 . P S / 2 m o u s e p o r tP S / 2 m o u s e p o r tP S / 2 m o u s e p o r tP S / 2 m o u s e p o r tP S / 2 m o u s e p o r t. This green 6-pin connector is for a PS/2 mouse. 2 .

2 . 2 . 2 .

2 . P S / 2 k e y b o a r d p o r tP S / 2 k e y b o a r d p o r tP S / 2 k e y b o a r d p o r tP S / 2 k e y b o a r d p o r tP S / 2 k e y b o a r d p o r t. This purple 6-pin connector is for a PS/2 keyboard.

3 . 3 . 3 . 3 .

3 . S e r i a l p o r tS e r i a l p o r tS e r i a l p o r tS e r i a l p o r tS e r i a l p o r t . This port connects a mouse, modem, or other devices that conforms with serial specification.

4 . 4 . 4 . 4 .

4 . P a r a l l e l p o r t .P a r a l l e l p o r t .P a r a l l e l p o r t .P a r a l l e l p o r t .P a r a l l e l p o r t . This 25-pin port connects a printer, scanner, or other devices.

5 . 5 . 5 . 5 .

5 . V G A p o r t . V G A p o r t . V G A p o r t . V G A p o r t . V G A p o r t . This port connects a VGA monitor. 6 .

6 . 6 . 6 .

6 . U S B 2 . 0 p o r t s 1 , 2 , 3 a n d 4 .U S B 2 . 0 p o r t s 1 , 2 , 3 a n d 4 .U S B 2 . 0 p o r t s 1 , 2 , 3 a n d 4 .U S B 2 . 0 p o r t s 1 , 2 , 3 a n d 4 .U S B 2 . 0 p o r t s 1 , 2 , 3 a n d 4 . These 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices.

7 7 7 7

7 ... C e n t e r / S u b w o o f e r p o r t ( y e l l o w o r a n g e ) .C e n t e r / S u b w o o f e r p o r t ( y e l l o w o r a n g e ) .C e n t e r / S u b w o o f e r p o r t ( y e l l o w o r a n g e ) .C e n t e r / S u b w o o f e r p o r t ( y e l l o w o r a n g e ) .C e n t e r / S u b w o o f e r p o r t ( y e l l o w o r a n g e ) . This port connects the center/subwoofer speakers.

8 . 8 . 8 . 8 .

8 . M i c r o p h o n e p o r t ( p i n k ) . M i c r o p h o n e p o r t ( p i n k ) . M i c r o p h o n e p o r t ( p i n k ) . M i c r o p h o n e p o r t ( p i n k ) . M i c r o p h o n e p o r t ( p i n k ) . This port connects a microphone. 9 .

9 . 9 . 9 .

9 . L i n e O u t p o r t ( l i m e ) .L i n e O u t p o r t ( l i m e ) .L i n e O u t p o r t ( l i m e ) .L i n e O u t p o r t ( l i m e ) .L i n e O u t p o r t ( l i m e ) . This port connects a headphone or a speaker. In 4-channel, 6-channel, and 8-channel configuration, the function of this port becomes Front Speaker Out.

(15)

1 - 5 1 - 51 - 5 1 - 5 1 - 5 A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1 1 0 . 1 0 .1 0 .

1 0 .1 0 . L i n e I n p o r t ( l i g h t b l u e ) .L i n e I n p o r t ( l i g h t b l u e ) .L i n e I n p o r t ( l i g h t b l u e ) .L i n e I n p o r t ( l i g h t b l u e ) . This port connects the tape, CD, DVDL i n e I n p o r t ( l i g h t b l u e ) . player, or other audio sources.

1 1 . 1 1 .1 1 .

1 1 .1 1 . R e a r S p e a k e r O u t p o r t ( g r a y ) .R e a r S p e a k e r O u t p o r t ( g r a y ) .R e a r S p e a k e r O u t p o r t ( g r a y ) .R e a r S p e a k e r O u t p o r t ( g r a y ) . This port connects the rearR e a r S p e a k e r O u t p o r t ( g r a y ) . speakers on a 4-channel, 6-channel, or 8-channel audio configuration. 1 2 .

1 2 .1 2 .

1 2 .1 2 . S i d e S p e a k e r O u t p o r t ( b l a c k ) .S i d e S p e a k e r O u t p o r t ( b l a c k ) .S i d e S p e a k e r O u t p o r t ( b l a c k ) .S i d e S p e a k e r O u t p o r t ( b l a c k ) . This port connects the sideS i d e S p e a k e r O u t p o r t ( b l a c k ) . speakers in an 8-channel audio configuration.

1 3 . 1 3 .1 3 .

1 3 .1 3 . P o w e r s u p p l y u n i t p o w e r s w i t c h .P o w e r s u p p l y u n i t p o w e r s w i t c h .P o w e r s u p p l y u n i t p o w e r s w i t c h .P o w e r s u p p l y u n i t p o w e r s w i t c h . This switch allows you to turnP o w e r s u p p l y u n i t p o w e r s w i t c h . ON or OFF the flow of power to the power supply unit.

1 4 . 1 4 .1 4 .

1 4 .1 4 . V o l t a g e s e l e c t o r .V o l t a g e s e l e c t o r .V o l t a g e s e l e c t o r .V o l t a g e s e l e c t o r . This switch allows you to adjust the systemV o l t a g e s e l e c t o r . input voltage according to the voltage supply in your area. See the “Voltage selector” section on page 1-6 before adjusting this switch. 1 5 .

1 5 .1 5 .

1 5 .1 5 . P o w e r s u p p l y u n i t f a n v e n t .P o w e r s u p p l y u n i t f a n v e n t .P o w e r s u p p l y u n i t f a n v e n t .P o w e r s u p p l y u n i t f a n v e n t . This vent is for the PSU fan thatP o w e r s u p p l y u n i t f a n v e n t . provides ventilation inside the power supply unit.

1 6 . 1 6 .1 6 .

1 6 .1 6 . P o w e r c o n n e c t o r .P o w e r c o n n e c t o r .P o w e r c o n n e c t o r .P o w e r c o n n e c t o r . This connector is for the power cable and plug.P o w e r c o n n e c t o r . 1 7 .

1 7 .1 7 .

1 7 .1 7 . C h a s s i s f a n v e n t .C h a s s i s f a n v e n t .C h a s s i s f a n v e n t .C h a s s i s f a n v e n t . This vent is for the fan that provides ventilationC h a s s i s f a n v e n t . inside the system chassis.

1 8 . 1 8 .1 8 .

1 8 .1 8 . I E E E 1 3 9 4 p o r t . I E E E 1 3 9 4 p o r t . I E E E 1 3 9 4 p o r t . I E E E 1 3 9 4 p o r t . This port connects IEEE 1394 devices such asI E E E 1 3 9 4 p o r t . digital still/video cameras, camcorders, external disk drives, or other devices.

1 9 . 1 9 .1 9 .

1 9 .1 9 . L A N ( R J - 4 5 ) p o r t . L A N ( R J - 4 5 ) p o r t . L A N ( R J - 4 5 ) p o r t . L A N ( R J - 4 5 ) p o r t . This port allows Gigabit connection to a LocalL A N ( R J - 4 5 ) p o r t . Area Network (LAN) through a network hub.

2 0 . 2 0 .2 0 .

2 0 .2 0 . E x p a n s i o n s l o t c o v e r sE x p a n s i o n s l o t c o v e r sE x p a n s i o n s l o t c o v e r sE x p a n s i o n s l o t c o v e r s. Remove these cover when installingE x p a n s i o n s l o t c o v e r s expansion cards.

Audio 2, 4, 6, or 8-channel configuration

Light Blue Line In Line In Line In Line In Lime Line Out Front Speaker Out Front Speaker Out Front Speaker Out Pink Mic In Mic In Mic In Mic In Gray • Rear Speaker Out Rear Speaker Out Rear Speaker Out

Black • • • Side Speaker Out

(16)

Voltage selector

The PSU has a 115 V/230 V voltage selector switch located beside the power connector. Use this switch to select the appropriate system input voltage according to the voltage supply in your area.

If the voltage supply in your area is 100-127 V, set the switch to 115 V. If the voltage supply in your area is 200-240 V, set the switch to 230 V.

Setting the switch to 115V in a 230V environment or 230V in a 115V environment will seriously damage the system!

(17)

1 - 7 1 - 71 - 7 1 - 7 1 - 7 A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1

1. 5.25-inch empty optical drive bay 2. Floppy disk drive bay

3. Front panel cover

4. Hard disk drive metal tray 5. Chassis fan

6. ASUS motherboard 7. DIMM sockets

8. LGA775 socket with PnP cap

9. PCI Express™ x16 slot for discrete graphics card

10. PCI slots

11. Serial ATA connectors 12. Expansion card slots 13. Power supply unit

1.4 Internal components

The illustration below is the internal view of the system when you remove the top cover and the power supply unit. The installed components are labeled for your reference. Proceed to Chapter 2 for instructions on installing additional system components.

(18)

1 - 8 1 - 8 1 - 8 1 - 8

(19)

Chapter 2

Basic installation

(20)

2 - 2 2 - 2 2 - 2 2 - 2 2 - 2 C h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o n

2.1 Preparation

Before you proceed, make sure that you have all the components you plan to install in the system.

Basic components to install

1. Central processing unit (CPU)

2. DDR Dual Inline Memory Module (DIMM) 3. Expansion card(s)

4. Hard disk drive 5. Optical drive 6. Floppy disk drive

T o o l

Phillips (cross) screw driver

The motherboard comes with an onboard standby power LED. This LED lights up to indicate that the system is ON, in sleep mode or in soft-off mode, and not powered OFF. Unplug the power cable from the power outlet and make sure that the standby power LED is OFF before installing any system component.

• Use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity.

• Hold components by the edges to avoid touching the ICs on them.

• Whenever you uninstall any component, place it on a grounded

antistatic pad or in the bag that came with the component.

2.2 Before you proceed

(21)

2.3 Removing the side plate and

front cover

The system has two chassis side plates, each one secured by two screws located on the rear panel.

To remove the chassis side plate: 1. Turn each screw

counterclockwise to release the side cover. Set the screws aside.

2. Slide the side panel for about half an inch toward the rear until it disengages from the chassis.

Remove only the left side plate.

3. Release the side lock tabs from the steel railing.

(22)

2 - 4 2 - 4 2 - 4 2 - 4

2 - 4 C h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o n

4. Swing the left edge of the front panel outward.

(23)

2.4.1

2.4.1 Installling the CPU

Installling the CPU

To install a CPU:

1. Locate the CPU socket on the motherboard.

2.4 Central Processing Unit (CPU)

The motherboard comes with a surface mount LGA775 socket designed for the Intel®_Pentium®_{4 processor in the 775-land package.}

• Your boxed Intel®_Pentium®_{4 LGA775 processor package should}

come with installation instructions for the CPU, fan and heatsink assembly. If the instructions in this section do not match the CPU documentation, follow the latter.

• Upon purchase of the system, make sure that the PnP cap is on the

socket and the socket pins are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket pins/motherboard components. ASUS will shoulder the cost of repair only if the damage is shipment/transit-related.

• Keep the cap after installing the motherboard. ASUS will process Return Merchandise Authorization (RMA) requests only if the motherboard comes with the cap on the LGA775 socket.

• The product warranty does not cover damage to the socket pins

resulting from incorrect CPU installation/removal, or misplacement/ loss/incorrect removal of the PnP cap.

Before installing the CPU, make sure that the socket box is facing towards you and the load lever is on your left.

®

(24)

2 - 6 2 - 6 2 - 6 2 - 6

2 - 6 C h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o n

3. Lift the load lever in the direction of the arrow to a 135º angle.

4. Lift the load plate with your thumb and forefinger to a 100º angle (A), then push the PnP cap from the load plate window to remove (B).

To prevent damage to the socket pins, do not remove the PnP cap unless you are installing a CPU.

5. Position the CPU over the socket, making sure that the gold triangle is on the bottom-left corner of the socket. The socket alignment key should fit

into the CPU notch. A l i g n m e n t k e yA l i g n m e n t k e yA l i g n m e n t k e yA l i g n m e n t k e yA l i g n m e n t k e y G o l d t r i a n g l e m a r k G o l d t r i a n g l e m a r kG o l d t r i a n g l e m a r k G o l d t r i a n g l e m a r kG o l d t r i a n g l e m a r k L o a d p l a t e L o a d p l a t eL o a d p l a t e L o a d p l a t eL o a d p l a t e A B

2. Press the load lever with your thumb (A) and move it to the left (B) until it is released from the retention tab.

(25)

The CPU fits in only one correct orientation. DO NOT force the CPU into the socket to prevent bending the connectors on the socket and damaging the CPU!

6. Close the load plate (A), then push the load lever (B) until it snaps into the retention tab.

A

B

Notes on Intel

®

_{Hyper-Threading Technology}

• This motherboard supports Intel®_Pentium®_{4 CPUs in the 775-land}

package with Hyper-Threading Technology.

• Hyper-Threading Technology is supported under Windows®_XP/2003

Server and Linux 2.4.x (kernel) and later versions only. Under Linux, use the Hyper-Threading compiler to compile the code. If you are using any other operating systems, disable the Hyper-Threading Technology item in the BIOS to ensure system stability and performance.

• Installing Windows®_{XP Service Pack 1 is recommended.}

• Make sure to enable the Hyper-Threading Technology item in BIOS

before installing a supported operating system.

• For more information on Hyper-Threading Technology, visit

www.intel.com/info/hyperthreading.

To use the Hyper-Threading Technology on this motherboard: 1. Install an Intel®_Pentium®_{4 CPU that supports Hyper-Threading}

Technology.

2. Power up the system and enter the BIOS Setup (see Chapter 5: BIOS setup). Under the Advanced Menu, make sure that the item

(26)

2 - 8 2 - 8 2 - 8 2 - 8 2 - 8 C h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o n

2.4.2

2.4.2 Installling the CPU heatsink and fan

Installling the CPU heatsink and fan

The Intel®_Pentium®_{4 LGA775 processor requires a specially designed}

heatsink and fan assembly to ensure optimum thermal condition and performance.

• When you buy a boxed Intel®_Pentium®_{4 processor, the package}

includes the CPU fan and heatsink assembly. If you buy a CPU separately, make sure that you use only Intel®_-certified

multi-directional heatsink and fan.

• Your Intel®_Pentium®_{4 LGA775 heatsink and fan assembly comes in}

a push-pin design and requires no tool to install.

If you purchased a separate CPU heatsink and fan assembly, make sure that a Thermal Interface Material is properly applied to the CPU heatsink or CPU before you install the heatsink and fan assembly.

To install the CPU heatsink and fan: 1. Place the heatsink on top of the

installed CPU, making sure that the four fasteners match the holes on the motherboard.

F a s t e n e r F a s t e n e rF a s t e n e r F a s t e n e rF a s t e n e r M o t h e r b o a r d h o l e M o t h e r b o a r d h o l e M o t h e r b o a r d h o l e M o t h e r b o a r d h o l e M o t h e r b o a r d h o l e

(27)

Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if you fail to plug this connector.

3. When the fan and heatsink assembly is in place, connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN1. 2. Push down two fasteners at a

time in a diagonal sequence to secure the heatsink and fan assembly in place. A A B B B B A A ® CPU_FAN1 GND CPU F AN PWR CPU F AN IN CPU F AN PWM

(28)

2 - 1 0 2 - 1 0 2 - 1 0 2 - 1 0 2 - 1 0 C h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o n

2.4.3

2.4.3 Uninstalling the CPU heatsink and fan

Uninstalling the CPU heatsink and fan

To uninstall the CPU heatsink and fan: 1. Disconnect the CPU fan

cable from the connector on the motherboard labeled CPU_FAN1.

2. Rotate each fastener counterclockwise.

(29)

2 - 1 1 2 - 1 1 2 - 1 1 2 - 1 1 2 - 1 1 A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1

4. Remove the heatsink and fan assembly from the

motherboard.

5. Rotate each fastener clockwise to reset the orientation.

(30)

2.5 Installing a DIMM

The system motherboard comes with two Double Data Rate (DDR) Dual Inline Memory Module (DIMM) sockets.

The following figure illustrates the location of the sockets:

• Installing DDR DIMMS other than the recommended configurations

may cause memory sizing error or system boot failure. Use any of the recommended configurations in the table on the next page. • Install only i d e n t i c a l i d e n t i c a l i d e n t i c a l i d e n t i c a l i d e n t i c a l (the same type and size) DDR DIMM in

DIMM_A and DIMM_B.

• Always install DIMMs with the same CAS latency. For optimum

compatibility, we recommend that you obtain memory modules from the same vendor.

• Due to chipset resource allocation, the system may detect less than 2 GB system memory when you installed two 1 GB DDR memory.

• This motherboard does not support memory modules made up of

128 Mb chips or double-sided x16 memory modules.

2.5.1

2.5.1 Memory configurations

Memory configurations

You may install up to 2 GB system memory using 256 MB, 512 MB, and 1 GB DDR DIMMs.

®

184-Pin DDR DIMM Sockets

(31)

2 - 1 3 2 - 1 3 2 - 1 3 2 - 1 3 2 - 1 3 A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1 A S U S V i n t a g e - P H 1 * U s e o n l y i d e n t i c a l D D R D I M M p a i r s . * U s e o n l y i d e n t i c a l D D R D I M M p a i r s . * U s e o n l y i d e n t i c a l D D R D I M M p a i r s . * U s e o n l y i d e n t i c a l D D R D I M M p a i r s . * U s e o n l y i d e n t i c a l D D R D I M M p a i r s . S o c k e t s S o c k e t s S o c k e t s S o c k e t s S o c k e t s M o d e M o d eM o d e M o d e M o d e D I M M 1D I M M 1D I M M 1D I M M 1D I M M 1 D I M M 2D I M M 2D I M M 2D I M M 2D I M M 2 Single-channel (1) Installed — (2) — Installed Dual-channel (3)* Installed Installed

Recommended memory configurations

S S S S S S S S S S - Single-sided D S D S D S D S D S - Double-sided C L C L C L C L C L- CAS Latency D I M M s u p p o r t : D I M M s u p p o r t : D I M M s u p p o r t : D I M M s u p p o r t : D I M M s u p p o r t : A A A A

A - supports one module inserted into either slot, in a Single-channel memory configuration.

B B B B

B - supports one pair of modules inserted into either the blue slots or the black slots as one pair of Dual-channel memory configuration.

C C C C

C - supports four modules inserted into the blue and black slots as two pairs of Dual-channel memory configuration.

DDR (400 MHz) Qualified Vendors List

Visit the ASUS website (www.asus.com) for the latest DDR Qualified Vendors List. S i z e S i z e S i z e S i z e S i z e V e n d o rV e n d o rV e n d o rV e n d o rV e n d o r M o d e lM o d e lM o d e lM o d e lM o d e l B r a n dB r a n dB r a n dB r a n dB r a n d S i d e ( s )S i d e ( s )S i d e ( s )S i d e ( s )S i d e ( s ) C o m p o n e n tC o m p o n e n tC o m p o n e n tC o m p o n e n tC o m p o n e n t C LC LC LC LC L AA BAAA BBBB CCCCC 256 MB KINGSTON KVR400X64C3A/256 Hynix SS HY5DU56822BT-D43 — • • • 512 MB KINGSTON KVR400X64C3A/512 Hynix DS HY5DU56822BT-D43 — • • • 256 MB KINGSTON KVR400X64C3A/256 Infineon SS HYB25D256800BT-5B — • • • 512 MB KINGSTON KVR400X64C3A/512 Infineon DS HYB25D256809BT-5B — • • • 256 MB KINGSTON KVR400X64C3A/256 KINGSTON SS D3208DL2T-5 — • • • 512 MB KINGSTON KVR400X64C3A/512 KINGSTON DS D328DIB-50 — • • • 512MB KINGSTON KHX3200A/512 N/A DS Heat-Sink Package — • • 256MB SAMSUNG M368L3223ETM-CCC SAMSUNG SS K4H560838E-TCCC — • • • 512MB SAMSUNG M368L6423ETM-CCC SAMSUNG DS K4H560838E-TCCC 3 • • 256MB SAMSUNG M368L3223FTN-CCC SAMSUNG SS K4H560838F-TCCC 3 • • 512MB SAMSUNG M368L6423FTN-CCC SAMSUNG DS K4H560838F-TCCC — • • 256MB Hynix HYMD232646B8J-D43 AA Hynix SS HY5DU56822BT-D43 3 • • • 512MB Hynix HYMD264646B8J-D43 AA Hynix DS HY5DU56822BT-D43 — • • • 256MB MICRON MT8VDDT3264AG-40BCB MICRON SS MT46V32M8TG-5BC — • • • 512MB MICRON MT16VDDT6464AG-40BCB MICRON DS MT46V32M8TG-5BC — • • • 256MB Infineon HYS64D32300GU-5-B Infineon SS HYB25D256800BT-5B 3 • • • 512MB Infineon HYS64D64320GU-5-B Infineon DS HYB25D256800BT-5B 3 • • 256MB Infineon HYS64D32300HU-5-C Infineon SS HYB25D256800CE-5C 3 • • • 512MB Infineon HYS64D64320HU-5-C Infineon DS HYB25D256800CE-5C — • • • 256MB CORSAIR CMX256A-3200C2PT Winbond SS W942508BH-5 2 • • • 512MB CORSAIR CMX512-3200C2 Winbond DS Heat-Sink Package 2 • • • 512MB CORSAIR VS512MB400 VALUE seLecT DS VS32M8-5 2.5 • • •

(32)

2.5.3

2.5.3 Removing a DIMM

Removing a DIMM

Follow these steps to remove a DIMM. 1. Simultaneously press the

retaining clips outward to unlock the DIMM.

2. Remove the DIMM from the socket.

Support the DIMM lightly with your fingers when pressing the retaining clips. The DIMM might get damaged when it flips out with extra force.

2.5.2

2.5.2 Installing a DIMM

Installing a DIMM

3. Firmly insert the DIMM into the socket until the retaining clips snap back in place and the DIMM is properly seated.

1. Unlock a DIMM socket by pressing the retaining clips outward.

2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket.

L o c k e d R e t a i n i n g C l i p L o c k e d R e t a i n i n g C l i pL o c k e d R e t a i n i n g C l i p L o c k e d R e t a i n i n g C l i pL o c k e d R e t a i n i n g C l i p

Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the motherboard and the components.

A DDR DIMM is keyed with a notch so that it fits in only one direction. DO NOT force a DIMM into a socket to avoid damaging the DIMM.

(33)

2.6 Expansion slots

In the future, you may need to install expansion cards. The following

sub-sections describe the slots and the expansion cards that they support.

2.6.1

2.6.1 Installing an expansion card

Installing an expansion card

To install an expansion card:

1. Before installing the expansion card, read the documentation that came with it and make the necessary hardware settings for the card. 2. Remove the system unit cover (if your motherboard is already

installed in a chassis).

3. Remove the bracket opposite the slot that you intend to use. Keep the screw for later use.

4. Align the card connector with the slot and press firmly until the card is completely seated on the slot.

5. Secure the card to the chassis with the screw you removed earlier. 6. Replace the system cover.

Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components.

2.6.2

2.6.2 Configuring an expansion card

Configuring an expansion card

After installing the expansion card, configure the it by adjusting the software settings.

1. Turn on the system and change the necessary BIOS settings, if any. See Chapter 5 for information on BIOS setup.

(34)

2 - 1 6 2 - 1 6 2 - 1 6 2 - 1 6

2 - 1 6 C h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o nC h a p t e r 2 : B a s i c i n s t a l l a t i o n

Standard interrupt assignments

I R Q I R QI R Q I R QI R Q P r i o r i t yP r i o r i t yP r i o r i t yP r i o r i t yP r i o r i t y S t a n d a r d F u n c t i o nS t a n d a r d F u n c t i o nS t a n d a r d F u n c t i o nS t a n d a r d F u n c t i o nS t a n d a r d F u n c t i o n 0 1 System Timer 1 2 Keyboard Controller 2 - Re-direct to IRQ#9

3 11 Communications Port (COM2)* 4 12 Communications Port (COM1)* 5 13 IRQ holder for PCI steering* 6 14 Floppy Disk Controller 7 15 Printer Port (LPT1)*

8 3 System CMOS/Real Time Clock 9 4 IRQ holder for PCI steering* 10 5 IRQ holder for PCI steering* 11 6 IRQ holder for PCI steering* 12 7 PS/2 Compatible Mouse Port* 13 8 Numeric Data Processor 14 9 Primary IDE Channel 15 10 Secondary IDE Channel

* T h e s e I R Q s a r e u s u a l l y a v a i l a b l e f o r I S A o r P C I d e v i c e s . * T h e s e I R Q s a r e u s u a l l y a v a i l a b l e f o r I S A o r P C I d e v i c e s . * T h e s e I R Q s a r e u s u a l l y a v a i l a b l e f o r I S A o r P C I d e v i c e s . * T h e s e I R Q s a r e u s u a l l y a v a i l a b l e f o r I S A o r P C I d e v i c e s . * T h e s e I R Q s a r e u s u a l l y a v a i l a b l e f o r I S A o r P C I d e v i c e s .

IRQ assignments for this motherboard

When using PCI cards on shared slots, ensure that the drivers support “Share IRQ” or that the cards do not need IRQ assignments; otherwise, conflicts will arise between the two PCI groups, making the system unstable and the card inoperable.

A A A A

A BBBBB CCCCC DDDDD EEEEE FFFFF GGGGG HHHHH

PCI slot 1 — — — — — used — —

PCI slot 2 — — — — — — used —

PCI Express x16 slot shared — — — — — — — PCI Express x1 slot1 — shared — — — — — — Onboard USB controller 1 — — — — — — — shared Onboard USB controller 2 — — — shared — — — — Onboard USB controller 3 — — shared — — — — — Onboard USB controller 4 shared — — — — — — — Onboard USB 2.0 controller — — — — — — — shared Onboard Azalia Audio shared — — — — — — — Onboard IDE Controller — — shared — — — — — Onboard SATA Controller — — — shared — — — —

(35)

2.6.3

2.6.3 PCI slots

PCI slots

The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. The figure shows a LAN card installed on a PCI slot.

2.6.4

2.6.4 PCI Express x16 slot

PCI Express x16 slot

This motherboard supports PCI Express x16 graphic cards that comply with the PCI Express specifications. The figure shows a graphics card installed on the PCI Express x16 slot.

2.6.5

2.6.5 PCI Express x1 slot

PCI Express x1 slot

This motherboard supports PCI

(36)

2 - 1 8 2 - 1 8 2 - 1 8 2 - 1 8

2.7 Installing an optical drive

Follow these steps to install a CD-ROM drive.

1. Place the chassis upright. 2. Insert the CD-ROM drive into

the upper 5.25-inch drive bay.

C D - R O M s c r e w h o l e s C D - R O M s c r e w h o l e s C D - R O M s c r e w h o l e s C D - R O M s c r e w h o l e s C D - R O M s c r e w h o l e s 3. Carefully push the CD-ROM

drive into the bay until its screw holes align with the holes on the bay as shown.

4. Secure the CD-ROM with two screws.

(37)

5. Connect a power cable from the power supply to the power connector at the back of the CD-ROM. Use the cable with the white connector. 6. Connect one end of the IDE

ribbon cable to the IDE interface at the back of the CD-ROM, matching the red stripe on the cable with Pin 1 on the IDE interface.

7. Connect one end of the CD-ROM audio cable to the 4-pin connector at the back of the CD-ROM.

8. Connect the other end of the IDE ribbon cable to the IDE connector on the motherboard. 9. Connect the other end of the

(38)

2 - 2 0 2 - 2 0 2 - 2 0 2 - 2 0

2.8 Installing a hard disk drive

The chassis has one 3.5-inch hard disk drive (HDD) bay right under the 5.25-inch bay. The following figures show the internal and external views of the HDD bay location.

5 . 2 5 - i n c h D r i v e b a y 5 . 2 5 - i n c h D r i v e b a y 5 . 2 5 - i n c h D r i v e b a y 5 . 2 5 - i n c h D r i v e b a y 5 . 2 5 - i n c h D r i v e b a y 3 . 5 - i n c h d r i v e b a y 3 . 5 - i n c h d r i v e b a y 3 . 5 - i n c h d r i v e b a y 3 . 5 - i n c h d r i v e b a y 3 . 5 - i n c h d r i v e b a y I n t e r n a l v i e w I n t e r n a l v i e wI n t e r n a l v i e w I n t e r n a l v i e wI n t e r n a l v i e w E x t e r n a l v i e wE x t e r n a l v i e wE x t e r n a l v i e wE x t e r n a l v i e wE x t e r n a l v i e w

Follow these steps to install an IDE HDD. 1. Place the chassis upright.

2. With the HDD label side up, carefully insert the drive into the 3.5-inch bay.

H D D l a b e l s i d e H D D l a b e l s i d eH D D l a b e l s i d e H D D l a b e l s i d e H D D l a b e l s i d e

3. Push the drive into the bay until its screw holes align with the holes on the bay marked HDD.

(39)

5. Connect a power cable from the power supply to the power connector at the back of the HDD. Use the cable with the white connector.

6. Connect the IDE hard disk ribbon cable to the IDE interface at the back of the HDD, matching the red stripe on the cable with Pin 1 on the IDE interface. R e d s t r i p e t o P i n 1 R e d s t r i p e t o P i n 1 R e d s t r i p e t o P i n 1 R e d s t r i p e t o P i n 1 R e d s t r i p e t o P i n 1 I D E r i b b o n c a b l e I D E r i b b o n c a b l e I D E r i b b o n c a b l e I D E r i b b o n c a b l e I D E r i b b o n c a b l e P o w e r c a b l eP o w e r c a b l eP o w e r c a b l eP o w e r c a b l eP o w e r c a b l e

7. Connect the other end of the IDE ribbon cable to the primary IDE connector on the

(40)

2 - 2 2 2 - 2 2 2 - 2 2 2 - 2 2

2.9 Installing a floppy disk drive

The Vintage-PH1 system comes with one 3.25-inch drive bay for a floppy disk drive.

To install a floppy disk drive:

1. Remove the front panel cover.

For instructions on how to remove the front panel cover, refer to page 2-3 of section “2.3 Removing the side plate and front cover”

2. Carefully insert the floppy disk drive into the floppy drive bay until the screw holes align with the holes on the bay.

3. Secure the floppy disk drive with two screws. 4. Connect the floppy disk drive

signal cable to the signal connector at the back of the drive.

5. Connect the other end of the signal cable to the floppy disk drive connector on the

motherboard.

6. Connect a power cable from the power supply unit to the power connector at the back of the floppy disk drive.

(41)

2.10 Re-connecting cables

You may have disconnected some cables when you were installing components. You must re-connect these cables before you replace the chassis cover.

LED cables

Connect the r e s e t b u t t o n , p o w e r s w i t c hr e s e t b u t t o n , p o w e r s w i t c hr e s e t b u t t o n , p o w e r s w i t c hr e s e t b u t t o n , p o w e r s w i t c hr e s e t b u t t o n , p o w e r s w i t c h, p o w e r L E D , p o w e r L E D , p o w e r L E D , p o w e r L E D , and H D Dp o w e r L E D , H D DH D DH D DH D D L E D

L E DL E D

L E DL E D cables to their respective leads in the system panel connector on the motherboard. H D D L E D H D D L E DH D D L E D H D D L E D H D D L E D P o w e r L E D P o w e r L E DP o w e r L E D P o w e r L E D P o w e r L E D P o w e r S w i t c h P o w e r S w i t c h P o w e r S w i t c h P o w e r S w i t c h P o w e r S w i t c h R e s e t b u t t o n R e s e t b u t t o n R e s e t b u t t o n R e s e t b u t t o n R e s e t b u t t o n ® F_PANEL1

System panel connector * Requires an ATX power supply.

(42)

PLED-2 - PLED-2 4 2 - 2 4 2 - 2 4 2 - 2 4

2.11 Replacing the side plate and front

cover

After you have installed all the internal components and you have

connected all the necessary cables, you are now ready to put the system back together.

1. Hook the hinge-like tabs to the holes on the right side of the front panel to attach the front panel assembly to the chassis. 2. Swing the front panel inward.

H i n g e - l i k e t a b H i n g e - l i k e t a b H i n g e - l i k e t a b H i n g e - l i k e t a b H i n g e - l i k e t a b

(43)

4. Fit the rail tabs on the side plate into the locking tab holes in the chassis.

5. Firmly push the side plate from the rear until it fits the chassis completely.

The locking tabs snap into the hole on the chassis to indicate that the side plate is in place.

S c r e w S c r e w S c r e w S c r e w S c r e w 6. Lock the side plate with the

(44)

2 - 2 6 2 - 2 6 2 - 2 6 2 - 2 6

2.13 Connecting external devices

The figure below shows the specific connectors and devices that you can connect to the rear panel ports.

Serial PS/2 KB

VGA

Line Out Line In Mic

(45)

Chapter 3

Starting up

(46)

3 - 2 3 - 2 3 - 2 3 - 2

3 - 2 C h a p t e r 3 : S t a r t i n g u pC h a p t e r 3 : S t a r t i n g u pC h a p t e r 3 : S t a r t i n g u pC h a p t e r 3 : S t a r t i n g u pC h a p t e r 3 : S t a r t i n g u p

3.1 Installing an operating system

The barebone system supports Windows®_{2000/XP operating systems}

(OS). Always install the latest OS version and corresponding updates so you can maximize the features of your hardware.

3.3 Support CD information

The support CD that came with the system contains useful software and several utility drivers that enhance the system features.

3.2 Powering up

The system has two power buttons located in the front panel. Press the system power button ( ) to enter the OS.

P r e s s t o t u r n O N t h e s y s t e m P r e s s t o t u r n O N t h e s y s t e m P r e s s t o t u r n O N t h e s y s t e m P r e s s t o t u r n O N t h e s y s t e m P r e s s t o t u r n O N t h e s y s t e m

Because motherboard settings and hardware options vary, use the setup procedures presented in this chapter for general reference only. Refer to your OS documentation for more information.

• Screen display and driver options may not be the same for other operating system versions.

• The contents of the support CD are subject to change at any time

(47)

3.3.1

3.3.1 Running the support CD

Running the support CD

To begin using the support CD, place the CD in your optical drive. The CD automatically displays the D r i v e r s D r i v e r s D r i v e r s D r i v e r s D r i v e r s menu if Autorun is enabled in your computer.

If A u t o r u n A u t o r u n A u t o r u n A u t o r u n A u t o r u n is NOT enabled in your computer, browse the contents of the support CD to locate the file ASSETUP.EXE from the BIN folder. Double-click the A S S E T U P . E X EA S S E T U P . E X EA S S E T U P . E X EA S S E T U P . E X EA S S E T U P . E X E to run the CD.

C l i c k a n i t e m t o i n s t a l l C l i c k a n i t e m t o i n s t a l l C l i c k a n i t e m t o i n s t a l l C l i c k a n i t e m t o i n s t a l l C l i c k a n i t e m t o i n s t a l l C l i c k a n i c o n t o C l i c k a n i c o n t o C l i c k a n i c o n t o C l i c k a n i c o n t o C l i c k a n i c o n t o d i s p l a y s u p p o r t d i s p l a y s u p p o r t d i s p l a y s u p p o r t d i s p l a y s u p p o r t d i s p l a y s u p p o r t C D / m o t h e r b o a r d C D / m o t h e r b o a r d C D / m o t h e r b o a r d C D / m o t h e r b o a r d C D / m o t h e r b o a r d i n f o r m a t i o n i n f o r m a t i o n i n f o r m a t i o n i n f o r m a t i o n i n f o r m a t i o n

QFE Update

Installs the Quick Fix Engineering (QFE) driver updates.

Intel Chipset Inf Update Program

This item installs the Intel®_{Chipset INF Update Program. This driver enables}

Plug-n-Play INF support for the Intel®_{chipset components on the}

motherboard. When installed to the target system, this driver provides the method for configuring the chipset components.

(48)

3 - 4 3 - 4 3 - 4 3 - 4 3 - 4 C h a p t e r 3 : S t a r t i n g u pC h a p t e r 3 : S t a r t i n g u pC h a p t e r 3 : S t a r t i n g u pC h a p t e r 3 : S t a r t i n g u pC h a p t e r 3 : S t a r t i n g u p

3.3.2

3.3.2 Utilities menu

Utilities menu

The Utilities menu shows the applications and other software that the motherboard supports.

Realtek Audio Driver

Executes the wizard to install the Realtek®_{ALC861 audio driver and}

application. When the phone jacks of the High Definition Audio panel are configured as output, use the master volume to adjust the sound.

Intel(R) PRO/100 and PRO/1000 Adapters Driver

Installs the Intel®_{PRO/100 and PRO/1000 Adapters Driver.}

Intel (R) Graphics Accelerator Driver

Installs the Intel®_{Graphics Accelerator Driver.}

USB 2.0 Driver

Installs the USB 2.0 driver.

ASUS PC Probe

(49)

ASUS Update

The ASUS Update utility allows you to update the motherboard BIOS in a Windows®_{environment. This utility requires an Internet connection either}

through a network or an Internet Service Provider (ISP).

Microsoft DirectX

Installs the Microsoft®_{DirectX 9.0c driver.}

Anti-virus application

The anti-virus application scans, identifies, and removes computer viruses. View the online help for detailed information.

ADOBE Acrobat Reader

Installs the Adobe®_Acrobat®_{Reader V5.0.}

ASUS Screen Saver

Installs the ASUS screen saver.

The screen display and utilities option may not be the same for different operating system versions.

3.2.3

3.2.3 ASUS Contact information

ASUS Contact information

(50)

3 - 6 3 - 6 3 - 6 3 - 6

(51)

Chapter 4

Motherboard info

(52)

4 - 2 4 - 2 4 - 2 4 - 2 4 - 2 C h a p t e r 4 : M o t h e r b o a r d i n f oC h a p t e r 4 : M o t h e r b o a r d i n f oC h a p t e r 4 : M o t h e r b o a r d i n f oC h a p t e r 4 : M o t h e r b o a r d i n f oC h a p t e r 4 : M o t h e r b o a r d i n f o

4.1 Introduction

The Vintage-PH1 barebone system comes with an ASUS motherboard. This chapter provides technical information about the motherboard for future upgrades or system reconfiguration.

4.2 Motherboard layout

Below: Center/Subwoofer Center: Side Speaker Out Top:Rear Speaker Out

3 2 2 1 +5V (Default) +5VSB USBPW56 USBPW78 (Default) +5V +5VSB KBPWR1 2 3 1 2 CLRTC1

Normal Clear CMOS (Default) 1 2 2 3 CR2032 3V Lithium Cell CMOS Power CD1 Super I/O Intel FWH 4Mb ATX12V1 FLOPPY1 AAFP1

DDR DIMM_A1 (64 bit,240-pin module)

KBPWR1 SB_PWR1 USBPW34 USBPW12 F_PANEL1 CHASSIS1 USB78 USB56 USBPW56 USBPW78 CLRTC1 SATA1 PCI1 Intel MCH 915G Intel ICH6

DDR DIMM_A2 (64 bit,240-pin module) DDR DIMM_B1 (64 bit,240-pin module) DDR DIMM_B2 (64 bit,240-pin module)

CHA_FAN1 CPU_FAN1 PRI_IDE1 ALC880 EA TXPWR1 SATA3 SATA2 SATA4 PCI2 SPDIF_OUT1 Kinnereth 82541PI R LGA775 PS/2KBMS T: Mouse B: Keyboard Below:Mic In Center:Line Out Top:Line In F_USB12 LAN_USB34 PCIEX1_1 PCIEX16 COM1 P ARALLEL POR T VGA1 PLED1 R ® USBPW12 USBPW34 3 2 2 1 +5V (Default) +5VSB F_PANEL1 FANPWR1 PLED1 PLED+ 1 NC PLED-FANPWR1 DC mode PWM (Default) 1 2 2 3 TI TSB43AB22A IE1394_2 COM2

* Requires an ATX power supply.

Vintage-PH1. Barebone System

Table of contents

Chapter 1: System Introduction

Chapter 1: System Introduction

Chapter 1: System Introduction

Chapter 1: System Introduction

Chapter 1: System Introduction

Chapter 2:

Chapter 2:

Chapter 2:

Chapter 2:

Chapter 2:

Basic Installation

Basic Installation

Basic Installation

Basic Installation

Basic Installation

Table of contents

Chapter 3:

Chapter 3:

Chapter 3:

Chapter 3:

Chapter 3:

Starting up

Starting up

Starting up

Starting up

Starting up

Chapter 4:

Chapter 4:

Chapter 4:

Chapter 4:

Chapter 4:

Motherboard Info

Motherboard Info

Motherboard Info

Motherboard Info

Motherboard Info

Chapter 5:

Chapter 5:

Chapter 5:

Chapter 5:

Chapter 5:

BIOS Information

BIOS Information

BIOS Information

BIOS Information

BIOS Information

Notices

Federal Communications Commission Statement

Federal Communications Commission Statement

Federal Communications Commission Statement

Federal Communications Commission Statement

Federal Communications Commission Statement

Canadian Department of Communications Statement

Canadian Department of Communications Statement

Canadian Department of Communications Statement

Canadian Department of Communications Statement

Canadian Department of Communications Statement

Safety information

Electrical safety

Electrical safety

Electrical safety

Electrical safety

Electrical safety

Operation safety

Operation safety

Operation safety

Operation safety

Operation safety

About this guide

Audience

Audience

Audience

Audience

Audience

How this guide is organized

How this guide is organized

How this guide is organized

How this guide is organized

_{Hyper-Threading Technology}

_{Hyper-Threading Technology}