Comparison between E LWD and CIV measurements
Ionization in the atmosphere, comparison between measurements and simulations
... Figure 5 shows the resulting modulation fractions, f , as a function of altitude from the measured data and from the O’Brien flux simulation. We also show the modulation of the ionization rate from the U-K simulation. It ...
5
A first comparison of irregularity and ion drift velocity measurements in the E-region
... Abstract. E-region irregularity velocity measurements at large flow angles with the STARE Finland coherent VHF radar are considered in context of the ion and electron ve- locity data provided by the EISCAT ...
15
Children's exposure assessment of radiofrequency fields: comparison between spot and personal measurements
... Classrooms b 25 a 119.51 (135.61) 60.69 (3.84) 81.10 (21.44-181.44) 224.87 2.77 603.22 Playground 26 255.62 (244.38) 157.34 (3.07) 200.10 (97.32-290.51) 655.86 9.28 950.74 Parks 78 623.31 (1895.78) 154.91 (4.36) 122.96 ...
37
Diagnostics of hypercortisolism — comparison between the clinical usefulness of salivary and serum cortisol measurements
... Another aspect of salivary cortisol procedure is sample collection and storage. Saliva collection should be done between 11 pm and midnight. In healthy indi- viduals with stable circadian rhythm, the level of ...
5
Temporal variation of sound speed in ocean: a comparison between GPS/acoustic and in situ measurements
... (XBT) measurements periodically carried out during the ...independent measurements are in good agreement within 5% of the typical amplitude of temporal ...
6
Metrology of a mirror at the Advanced Photon Source: comparison between optical and x-ray measurements
... It consists of radiation from a bending magnet source, a system of vertical and horizontal slits, a collimating mirror, a double-crystal monochromator, a set of narrow vertical slits (be[r] ...
14
Comparison between automated and manual measurements of carotid intima-media thickness in clinical practice
... automated measurements published for bifurcation and IC segments are still ...automated measurements clearly shed light on this field, pointing out to good reproducibility in all carotid segments without ...
7
Comparison between Online and Laboratory Measurements of Fault Gases for Mineral Oil and Natural Ester
... B. Comparison under Simulated PD Faults In the PD test, Gemini X was taken as the sample ...close between online and lab DGA methods, with a deviation of 30% which was probably introduced by the delay ...
9
Comparison of keratometric measurements between color light-emitting diode topography and Scheimpflug camera
... The two devices may not be used interchangeably. In the present study, the results of Pearson correlation analysis showed high correlation between the corneal re- fractive powers of the anterior and posterior ...
9
Automatic morphological sieving: comparison between different methods, application to DNA ploidy measurements
... It seems then that global and non parametric classifi- cation methods such as the MM method can be suc- cessfully compete with the more popular parametric methods (MA and NN). Nevertheless, performances of MA and NN ...
8
A Comparison of LiDAR and Radiosonde Wind Measurements
... LiDAR measurements are already well established in the wind energy research and their accuracy has been tested against met mast data up to 100 m above ...verify measurements at higher ...campaign ...
7
Sound transmission loss of cross-laminated timber walls: Comparison between measurements carried out in transmission suites and point mobility measurements
... of measurements, it is possible to estimate the loss factor of the partition and its bending stiffness which, in turn, can be used to determine its sound transmission loss once some basic physical properties are ...
8
Verification of Electromagnetic Field Measurements via Inter-laboratory Comparison Measurements
... inter-laboratory comparison indicated that the mea- surement devices are generally capable of validating the compliance with legal limit values if the employees have the required ...comparability between ...
7
Comparison of the annealing behaviour between cold and warm rolled ELC steels by thermoelectric power measurements
... However, one last phenomenon that has to be explained is why two steels with identical composition and warm deformation temperature, WR-A and WR-B, show a different recrystallisation behaviour, since no stagnation of the ...
21
Comparison between computed balance velocities and GPS measurements in the Lambert Glacier basin, East Antarctica
... The major sources of error in this region, where ice thickness values have been collected and hence are assumed well known, are found to be the uncertainties present in the accumulation [r] ...
7
Comparison of stopped delay between field measurements and HCM 2010 estimations at actuated signalized intersections
... Wang et al. (2015) studied the comparison of HCM 2000 delay model to field control delay. The field data required for estimating delay was obtained from three fixed-time signalized intersections in Shanghai. The ...
55
Meteor radar measurements of mean winds and tides over Collm (51.3 N, 13 E) and comparison with LF drift measurements 2005–2007
... wind measurements from 1959-2008, using the iono- spherically reflected sky wave of three commercial radio ...varying between about 80 and 120 km, have been estimated between late 1982 and 2007 using ...
7
Comparison between IRI and preliminary Swarm Langmuir probe measurements during the St Patrick storm period
... density measurements are still undergoing a thorough validation, a comparison with IRI in terms of absolute values would have not been ...differences between trends modelled by IRI and those observed ...
18
Palatal Surface Area of Maxillary Plaster Casts A Comparison Between Two-Dimensional and Three-Dimensional Measurements
... separate measurements of C and P, assuming equal contributions from the two (because delin- eation of the cleft and of the segments are similar processes); resulting in CV C/P ⫽ CV P ⫻ 兹2 ...
10
LWD and DCP
... Select site and set up LWD connection to its computational unit. The test section should be level and smooth. Set the plate on a prepared surface and seat it by turning it left and right 45 degrees. Do not drop ...
48