Configuration Commands for Use with TELNET
CWMP configuration commands
... By default, no password is configured for connecting to the ACS. Make sure the ACS username and password are the same as configured on the ACS. If not, the CPE cannot establish a CWMP connection to the ACS. If you ...
14
Routing Protocol Configuration Commands
... During configuration, the system can automatically generate a sequence for each item, starting from 10 by default and then adding 10 in ...to use the unsupported match regulations or set regulations to ...
296
LISP Interface Configuration Commands
... to use the IPv4 address of a different interface as the source locator for the outbound LISP-encapsulated packets rather than that of the outgoing ...to use the address of this loopback interface as the ...
8
Rip Protocol Configuration Commands
... logging commands in seconds for this command configures a major issue by ifname ...that use so, neighbors that any protocol ...RIP-2 configuration Infinet ...to commands will ...these ...
18
Telnet, Console and AUX Port Passwords on Cisco Routers Configuration Example
... typically Telnet, is the most common security that needs configuring, but protecting the router from unauthorized local access cannot be ...should use in an effective in−depth network security ...
8
Converting CLI Commands to Network Configuration Format
... then use it to convert configuration commands to NETCONF ...of commands even if the corresponding feature sets or the required hardware capabilities are not available on the device, you might ...
MAX T1/E1 Configuration Commands. Table of Contents
... It is possible to control multiple PRIs with a single D channel. If each PRI uses Non Facility Associated Signaling (NFAS), you can configure the other PRIs in the NFAS group to use all 24 DS0s as B channels. The ...
22
AMI Configuration Commands Reference Manual Part 2
... specification to be exceeded and is a potential safety hazard. The equipment must be installed such that with the exception of the connections to the host, clearance and creepage distances shown in the table below are ...
436
Table of Contents 1 CFD Configuration Commands 1-1
... &<1-10> indicates you can specify up to 10 MEP ID ranges. service-instance instance-id: Specifies the service instance ID, ranging from 1 to 32767. Description Use the cfd meplist command to create a MEP list, ...
27
Configuring SSH and Telnet
... • Starting from Cisco NX-OS Release 8.4(1), you can use 4096 bit RSA keys to secure SSH, SCP and SFTP sessions. • SSH public and private keys imported into user accounts that are remotely authenticated through a ...
20
Configuring SSH and Telnet
... switch(config)# username user1 keypair export bootflash:key_rsa rsa keyword is omitted and SSH keys are already present. To export the generated key pair, you are prompted to enter a passphrase that encrypts the private ...
26
Configuring SSH and Telnet
... The user authentication mechanisms supported for SSH are RADIUS, TACACS+, and the use of locally stored user names and passwords. SSH Client The SSH client feature is an application running over the SSH protocol ...
Configuring SSH and Telnet
... • Beginning in Cisco NX-OS Release 5.1, SSH runs in FIPS mode. • The SFTP server feature does not support the regular SFTP chown and chgrp commands. • When the SFTP server is enabled, only the admin user can ...
24
Configuring SSH and Telnet
... The user authentication mechanisms supported for SSH are RADIUS, TACACS+, LDAP, and the use of locally stored usernames and passwords. SSH Client The SSH client feature is an application that runs over the SSH ...
26
Configuration and Image File Commands
... Example switchxxxxxx(config)# ip dhcp tftp-server ip address autodhcp management vlan ipv6 dhcp client information refresh To set the refresh time and the minimum refresh time for DHCPv6 stateless client, use the ...
DHCP Service Configuration Mode Commands
... This keyword is license-enabled and available with valid MPLS feature license only. Important For DHCP over MPLS feature to work in StarOS 9.0 onward the dhcp ip vrf command must be configured in DHCP service. Without ...
32
Standard ACL Configuration Mode Commands
... Device Modes application-accelerator central-manager Usage Guidelines Use access lists to control access to specific applications or interfaces on a WAAS device. An access control list consists of one or more ...
MAG Service Configuration Mode Commands
... seconds must be an integer from1 through 262140. Usage Guidelines Use this command to limit PMIPv6 lifetime on this service. If the Proxy Binding Acknowledge (PBA) from the LMA contains a lifetime shorter or ...
24
Ethernet Interface Configuration Mode Commands
... num-retry number Specifies how many times to retry sending monitor packets to the IP address being monitored before performing the switchover. The number must be an integer from 1 through 100. Default: 5 Usage Guidelines ...
EDR Format Configuration Mode Commands
... Guidelines Use this command to configure either comma or tab as the delimiter between EDR ...CLI configuration is introduced to choose the delimiter character between both comma and ...
30