[PDF] Top 20 AIR CONDITIONER INSTALLATION MANUAL

... It will cause product breakdown or electric shock.. • Children should be supervised to ensure that they do not play with the appliance.[r] ... See full document

... CAUTION Installer setting mode is to set the detail function of the remote controller. If the installer setting mode is not set correctly, it can cause problems to the product, user injury or property damage. This must ... See full document

... Vertical Air Handling Unit • The drainage performance has to be optimized by installing both primary and secondary drain lines along with properly sized condensate traps in order to prevent property ... See full document

... CHECK THE FOLLOWING ITEMS WHEN INSTALLATION IS COMPLETE • After completing work, be sure to measure and record trial run properties, and store measured data, etc. • Measuring items are room temperature, outside ... See full document

... • Outdoor joint of gas side pipe should be installed horizontally due to the combination of variable units when the height of the main pipe is lower than the outlet of the pipe of the outdoor unit. The ... See full document

... the air filter once every 2 weeks. Dust and impurities collected in the air filter may block the air flow or weaken the cooling / dehumidifying ... See full document

... CHECK THE FOLLOWING ITEMS WHEN INSTALLATION IS COMPLETE • After completing work, be sure to measure and record trial run properties, and store measured data, etc. • Measuring items are room temperature, outside ... See full document

... ④ For connection of the Dry contact (PQDSBC), refer to the manual supplied with the Dry contact (PQDSBC). ■ AHU Control Kit ① Thermistor cable and remote controller wire should be located at least 50mm away from ... See full document

... Wiring Connection Make sure that the screws of the terminal are free from looseness. After the confirmation of the above conditions, prepare the wiring as follows: 1) Never fail to have separate power specially for the ... See full document

... • Ground the unit following local electrical codes. • Connect all wiring tightly. Loose wiring may cause overheating at connection points and a possible fire hazard. When transporting: Be careful when picking up and ... See full document

... 3. If outdoor unit is installed close to the seaside, it should avoid direct exposure to the sea wind. Otherwise it needs additional anticorrosion treatment on the heat exchanger. 1. If you can’t meet above guide line in ... See full document

... 6. No ignition sources No person carrying out work in relation to a refrigeration system which involves exposing any pipe work that contains or has contained flammable refrigerant shall use any sources of ignition in ... See full document

... • Ground the unit following local electrical codes. • Connect all wiring tightly. Loose wiring may cause overheating at connection points and a possible fire hazard. When transporting: Be careful when picking up and ... See full document

... And the lift distance must be less than 200mm, otherwise the water will overflow when the air conditioner stops. The end of the drainpipe should be over 50mm higher than the ground or the bottom of the ... See full document

... 2. If there is any vibration transmitted to the building, mount the rubber underneath the outdoor unit. Refrigerant amount Before shipment, this air conditioner is filled with the rated amount of ... See full document

... this manual and conditions or methods of installation, operation, use and maintenance of the photovoltaic ( PV ) product are beyond our control, we do not take any responsibility and expressly disclaim ... See full document

... the air purging of the charge hose by connecting the charging hose of gauge mani- fold to the charging port of 3 way valve and opening the low-pressure valve ...the MANUAL AUTO button of the indoor unit for ... See full document

... These air conditioners use Thermoelectric “modules” sandwiched between high performance aluminium heat sinks, high CFM axial fans, and a patented electronic design to “pump” the heat from the inside of your ... See full document

... SEALED REFRIGERANT SYSTEM: If the sealed refrigeration system (defined for this purpose as the compressor, condenser coil, evaporator coil, reversing valve, check valve, capillary, filte[r] ... See full document

... OBTAINING WARRANTY PERFORMANCE: Service will be provided by the FRIEDRICH Authorized Dealer or Service Organization in your area. They are listed in the Yellow Pages. If assistance is required in obtaining warranty ... See full document