For All 2-Piece
BWE 150 FL 300 FLValve Size and
BWE 150 FL 300 FL Valve Size and
Port Size (in)
4 ×4 2100 2500 2100 6 ×4 790 820 800 6 ×6 5300 6500 (S)
5400 (L) 5300 8 ×6 2100 2200 (S) 2200 (L) 2100
8 ×8 11000 11000 (S) 12 ×12 25000 26000 25000 14 ×12 11000
Flow Characteristics (Cv)*
*Cv values equal the flow of water in U.S. Gallons per minute per 1 PSI pressure drop across a fully open valve.
(S) Short Pattern.
(L) Long Pattern.
Differential Pressure Valve Bore
Size (in) 275 500 740 4 2090 3300 4200 6 4400 8200 11200 8 9000 14000 20300 10 15000 22000 30500 12 29300 37400 46400 Stem Torques (in-lbs)
Seat Seal Codes 01, 01F, 14, 14F
Differential Pressure Valve Bore
Size (in) 275 500 740 4 2400 3300 4200 6 5400 8200 11200 8 10000 15000 20300 10 16000 23000 30500 12 32000 39000 46500 Stem Torques (in-lbs)*
Seat Seal Codes 02, 02F, 18, 28, 28F
* Stem Torques (in-lbs)
Seat Seal Codes 60, 60A, 92H Multiply trim 02 torque ×2.
Note: The torques listed are based on valves controlling the flow of clean liquid at ambient temperature. For torques at pressure less than 275 psi use the value for 275 psi. For any pressure above 275 but less than the maximum pressure listed, interpolation may be used. These torques are average breakaway torques for valves that have been in
the closed position for 24 to 48 hours and under the listed differential pressures. The breakaway torque is an instantaneous value. As soon as the ball has any movement, the torque will drop on the average to two-thirds of this value.
CONTENTS MENU
W-K-M
(p118) P R O D U C T S P E C I F I C A T I O N S
D
Y N AS
E A L®3 1 0 C 3 - P
I E C EF
L O A T I N GB
A L LV
A L V E SBody-Tailpiece Material Codes
Standard Materials (
1/
4" Full Bore – 2" Regular Port)
Part CS CS2* CS3* S1 S8 Body ASTM A105 ASTM A350 LF2 316 SS/A351 CF8M Body Plug** CS SS
TE AISI 4130 316 SS FE ASTM A350 LF2 316 SS/A351 CF8M Bonnet Cap Carbon Steel Zinc Plated SS
Packing
Alloy Steel Plated 18-8 SS Alloy Steel
18-8 SS Adjusting Screws Plated
Tailpiece
*CS2/CS3/S8—to be used for H2S service with S2 internal trim only.
Meets NACE MR-01-75.
**When body drain is specified.
Ball-Stem Material Codes
Part CS S1 S2 ML
Ball AISI 1213 CS
316 SS 316 SS B 164 Class B Chrome Plate Ni-Cu Alloy Spring for
— 304 SS†
Grounding Device
Stem AISI 1213 CS
316 SS 17-4PH B164 Class B Zinc Plated Ni-Cu Alloy Compression Ring Carbon Steel
18-8 SS Zinc Plated
Note: 1/2"– 2"R CS2/S8 — Used with S2 internal trim only.
For H2S service per NACE MR-01-75.
† When specified.
Seat-Seal Material Codes
Part 01 02 03 07 18 23 28† 60A* 92H*
Filled Acetal Special Filled 316 SS Seat TFE
TFE Plastic Viton
Filled TFE Celcon
TFE Stellite Chromium Oxide Coated Rear Seal — Hydrin
— Braided
Filled TFE O-Ring Graphite
Tailpiece Gasket TFE Filled TFE TFE Filled TFE Stem Seal TFE Filled TFE
Packing Graphite/TFE with 316 SS Cap
*1"F and larger.
† Weld end valves only.
Part (Body) CS, CS2, CS3, S1 S8 Lock Nut Alloy Steel, Plated 18-8 SS
Handle Carbon Steel
316 SS Zinc Plated
Handle Grip Vinyl Vinyl Actuator Codes
AISI 1018
CONTENTS MENU
CONTACT
www:
PRINT TECHNICAL DATA
CONTACT
HELP
W-K-M D
Y N AS
E A L®3 1 0 C 3 - P
I E C EF
L O A T I N GB
A L LV
A L V E SBody-Tailpiece Material Codes
Standard Materials (2" Full Bore – 4" Regular Port)
Part CS CS2* CS3* S1 S8
Body ASTM A105 ASTM A350 LF2
316 SS/A351 CF8M Grade LF2
Body Plug** CS SS Tailpiece ASTM A105 4130 316 SS/A351 CF8M Nameplate SS
Bonnet Cap Carbon Steel Plated Stainless Steel Packing
Alloy Steel Plated 18-8 SS Adjusting Screws
*CS2/CS3/S8 — to be used for H2S service.
Meets NACE MR-01-75.
**When body drain is specified.
Ball-Stem Material Codes
Part CS S1 ML
Ball CS Chrome Plate 316 SS B164 Class B Ni-Cu Alloy Grounding
— 304 SS†
Device Spring
Stem 1213 Zinc Plate 316 SS B164 Class B Ni-Cu Alloy Compression
4140 CS 303 SS Ring
Note: 2"F – 4"R CS2/S8 — Used with S1 internal trim only.
For H2S service per NACE MR-01-75.
† When specified.
Part (Body) CS, CS2, CS3, S1, S8 Wrench Handle Ductile Iron Wrench Head Bolt and Nut Alloy Steel
Stop Plate Retainer Ring Carbon Steel Stop Plate Carbon Steel Zinc Plated Actuator Codes
Seat-Seal Material Codes
Part 01 02 03 07 18 23 28† 60A 92H
Filled Acetal Special Filled 316 SS Seat TFE
TFE Plastic Viton
Filled TFE Celcon
TFE Stellite Chromium Oxide Coated
Rear Seal — Hydrin
— Braided
Filled TFE O-Ring Graphite
Tailpiece Gasket TFE Filled TFE TFE Filled TFE Stem Seal TFE Filled TFE
Packing Graphite/TFE with 316 SS Cap
† Weld end valves only.
CONTENTS MENU
CONTACT
www:
PRINT TECHNICAL DATA
CONTACT
HELP
W-K-M
(p120) P R O D U C T S P E C I F I C A T I O N S
D
Y N AS
E A L®3 1 0 C 3 - P
I E C EF
L O A T I N GB
A L LV
A L V E SDimension A Approximate dimensions in inches
B D E F G Q** R S T J W H**
B138 B110 B128 B182 B172 B103 B150 THD 150 RF 300 RF 600 RF 600 RJ SW BW
1/4 3.00 — — — — 7.00 — .38 .62 1.4 2.8 4.3 5/16-24 — .184 .31 .88 .55 8-32
3/8 3.00 — — — — — — .38 .62 1.4 2.8 4.3 5/16-24 — .184 .31 .88 .55 8-32
1/2 4.00 — — — — — — .50 .75 1.8 3.5 5.4 7/16-20 — .246 .44 1 .72 10-24
3/4 4.25 — — — — 8.25 — .75 1 1.9 3.6 5.4 7/16-20 — .246 .44 1 .75 10-24 1 4.50 5.00 6.50 8.50 8.50 — — 1 1.25 2.8 4.1 7.0 5/8-18 — .356 .69 1.25 1.14 1/4-20 11/2 5.25 6.50 7.50 9.50 9.50 9.25 — 1.5 1.75 3.6 5.0 9.5 3/4-16 — .430 .78 1.5 1.34 5/16-18 2 6.25 7.00 8.50 11.50 11.62 — 8.50 2 2.5 5.0 5.4 15.0 — 1.12 .692 .81 2.62 1.88 3/8-16 3 10.00 8.00 11.12 — — — 11.12 3 3.5 6.4 6.6 15.0 — 1.12 .692 1.25 3 2.32 1/2-13 Size
Dimensional Data (in)
Dimension A Approximate dimensions in millimeters
B D E F G Q** R S T J W H**
B138 B110 B128 B182RF B172RJ B103 B150 THD 150 RF 300 RF 600 RF 600 RJ SW BW
6 76 — — — — 178 — 10 16 35 70 108 5/16-24 — 5 8 22 14 8-32 10 76 — — — — — — 10 16 35 70 108 5/16-24 — 5 8 22 14 8-32 15 102 — — — — — — 13 19 44 89 146 7/16-20 — 6 10 25 18 10 -24 20 108 — — — — 210 — 19 25 49 92 146 7/16-20 — 6 10 25 19 10 -24 25 114 127 165 216 216 — — 25 32 71 103 178 5/8-18 — 9 18 32 29 1/4-20 40 133 165 190 241 241 235 — 38 44 90 127 241 3/4-16 — 11 21 38 34 5/16-18 50 159 178 216 292 295 — 216 51 64 127 137 381 — 28 18 21 67 48 3/8-16 80 254 203 283 — — — 282 76 89 164 167 381 — 28 18 32 76 59 1/2-13 Size
Dimensional Data (mm)
**American National Thread in inches.
B138 – Threaded
B110 – 150 Raised Face Flanges B128 – 300 Raised Face Flanges
Threaded
B182 – 600 Raised Face Flanges B172 – 600 Ring Joint Flanges B150 – 300 Butt Weld B103 – Socket Weld Flanged
Top View
Stem Dimensions
Stem Dimensions Top View
Front View
Front View
Dimensional Data (
1/
4"-3" Full Bore)
CONTENTS MENU
CONTACT
www:
PRINT TECHNICAL DATA
CONTACT
HELP
W-K-M D
Y N AS
E A L®3 1 0 C 3 - P
I E C EF
L O A T I N GB
A L LV
A L V E SB136 – Threaded
B100 – 150 Raised Face Flanges B120 – 300 Raised Face Flanges
Threaded
B114 – 600 Raised Face Flanges B170 – 600 Ring Joint Flanges B142 – 300 Butt Weld B106 – Socket Weld Flanged
Top View Top View
Front View
Front View
Dimensional Data (
1/
2"- 4" Regular Port)
Dimension A Approximate dimensions in inches
B C D E F G Q** R S T J W H**
B136 B100 B120 B114 RF B170 RJ B106 B142 THD 150 RF 300 RF 600 RF 600 RJ SW BW
1/2 3.88 — — — — 7.88 —
3/4 4.38 — — — — — — 1 4.25 5.00 6.50 8.50 8.50 8.25 — 11/2 — 6.50 7.50 9.50 9.50 — — 2 6.25 7.00 8.50 11.50 11.62 10.25 — 21/2 8.50 7.50 9.50 — — — — 3×2 — 8.00 11.12 14.00 14.12 — — 4 12.00 9.00 12.00 17.00 17.12 — 12.00 Size
Dimensional Data (in)
Dimensional Data (mm)
**American National Thread in inches.
.38 .5 .62 1.4 2.8 4.3 5/16-24 — .184 .31 .88 .55 8-32 .5 .75 .75 1.8 3.5 5.8 7/16-20 — .246 .44 1 .72 10-24 .75 1 1 1.9 3.6 5.8 7/16-20 — .246 .44 1 .75 10-24 1 1.5 1.5 3.0 4.3 7.0 5/8-18 — .356 .69 1.25 1.16 1/4-20 1.5 2 1.75 3.6 5.0 7.5 3/4-16 — .430 .78 1.5 1.34 5/16-18 2 2.5 2.5 5.0 5.4 15.0 — 1.12 .692 .81 2.62 1.88 3/8-16 2 3 2.5 5.0 5.4 15.0 — 1.12 .692 .81 2.62 1.88 3/8-16 3 4 3.5 6.4 6.6 15.0 — 1.12 .692 1.25 3 2.31 1/2-13
Dimension A Approximate dimensions in millimeters
B C D E F G Q** R S T J W H**
B136 B100 B120 B114 RF B170 RJ B106 B142 THD 150RF 300RF 600RF 600RJ SW BW
15 98 — — — — 200 — 20 111 — — — — — — 25 108 127 165 216 216 210 — 40 133 165 190 241 241 — — 50 159 178 216 292 295 260 — 65 216 190 241 — — — — 80×50 — 203 282 356 359 — — 100 305 229 305 432 435 — 305 Size
9 13 16 35 70 108 5/16-24 — 4 8 22 14 8-32 13 19 19 44 89 146 7/16-20 — 6 11 25 18 10-24 19 25 25 49 92 146 7/16-20 — 6 11 25 19 10-24 32 38 38 76 108 178 5/8-18 — 9 18 32 29 1/4-20 38 51 44 90 127 190 3/4-16 — 10 20 38 34 5/16-18 51 64 64 127 137 381 — 28 17 21 67 48 3/8-16 51 76 64 127 137 381 — 28 17 21 67 48 3/8-16 76 102 89 164 167 381 — 28 17 32 76 59 1/2-13 Stem
Dimensions
Stem Dimensions
CONTENTS MENU
CONTACT
www:
PRINT TECHNICAL DATA
CONTACT
HELP
W-K-M
Full Bore Regular Port End
Full Bore Regular Port End THD 2.27 1.36 25 20PN Flg 3.86 2.95 50PN Flg 5.44 4.54 100PN Flg 7.26 6.35 THD 5.44 3.63 40 20PN Flg 7.71 6.80 50PN Flg 10.9 9.07 100PN Flg 14.5 11.8 THD 10.4 5.67 150PN Flg 15.0 10.4 50 300PN Flg 17.2 11.3 600PN Flg 21.3 15.0 BW 13.6 — 20PN Flg 29.0 23.1 75 50PN Flg 36.7 35.0 100PN Flg 39.5 36.7 BW 30.4 27.7 6mm – 100mm Weight (kg)
End Connection Valve Size and
Port Size (in) Threaded BWE 150FL 300FL 600FL
1/4×1/4 9.1 — — — — Flow Characteristics (Cv)*
*Flow of water in U.S. gal / min /1psi Pressure Prop.
CONTENTS MENU
W-K-M D
Y N AS
E A L®3 1 0 C & 3 1 0 D 3 - P
I E C EF
L O A T I N GB
A L LV
A L V E SDifferential Pressure Valve Bore
Size (in) 275 500 740
1/4 36 36 36
3/8 36 36 36
1/2 60 60 60
3/4 90 90 90
1 120 150 180 11/2 240 330 420 2 500 640 810 3 1010 1800 2400 Stem Torques (in-lbs)
Seat Seal Codes 01, 02 (150 –300 Class)
Differential Pressure Valve Bore
Size (in) 275 500 740 1000 1500 2250
1/4 60 60 60 60 72 84
3/8 60 60 60 60 72 84
1/2 60 60 60 70 84 108
3/4 128 128 145 160 215 360 11/2 520 580 680 810 980 1390
2 910 1042 1240 1500 1765 2300 3 1200 1800 2400 2900 3420 — Stem Torques (in-lbs)*
Seat Seal Codes 02 (Threaded, 600 Class), 18, 28
Differential Pressure Valve
Bore
Size (in) 275 500 740 1000 1500 2000 2250 2500 3000
1/4 50 50 50 50 50 60 75 85 100
3/8 50 50 50 50 50 60 75 85 100
1/2 60 60 60 72 100 120 140 180 220
3/4 108 108 125 140 190 260 340 420 500 1 264 264 290 320 380 440 510 620 — 11/2 480 528 610 726 895 1070 1270 1510 — 2 900 980 1110 1300 1520 1750 2000 — — 3 1650 1920 2200 2510 3110 3700 4000 — — Stem Torques (in-lbs)
Seat Seal Codes 03 (High Pressure Seats)
Differential Pressure Valve Bore
Size (in) 275 500 740 1000 1500 2000 2250 2500 3000 3500 3750 4000 4500 500
1/4 60 60 60 60 60 65 70 85 100 115 125 130 150 165
3/8 60 60 60 60 65 70 75 85 100 125 — — — —
1/2 70 70 70 82 110 125 140 180 220 276 — — — —
3/4 108 108 125 140 190 260 340 420 560 695 — — — — 1 264 264 290 320 380 440 510 620 760 — — — — — 2 900 980 1100 1300 1520 1750 2000 2550 2550 — — — — — Stem Torques (in-lbs)
Seat Seal Codes 23
* Stem Torques (in-lbs)
Seat Seal Codes 60, 60A, 92H
Full Regular Liquid 275 Dry Gas Dry Gas Bore Bore PSI 275 PSI 740 PSI
1/4F 1/2R 36 42 113
1/2F 3/4R 60 82 220
3/4F 1 R 90 150 404 1 F — 180 336 606 11/2 F 2 R 420 840 2260
2 F 21/2 R 900 1200 3230 3 F 4 R 2400 3600 9690 Stem Torques (in-lbs)
Seat Seal Codes 07
Multiply trim 02 torque ×2.
Note: The torques listed are based on valves controlling the flow of clean liquid at ambient temperature. For torques at pressure less than 275 psi use the value for 275 psi. For any pressure above 275 but less than the maximum pressure listed, interpolation may be used. These torques are average breakaway torques for valves that have been in
the closed position for 24 to 48 hours and under the listed differential pressures. The breakaway torque is an instantaneous value. As soon as the ball has any movement, the torque will drop on the average to two-thirds of this value.
CONTENTS MENU
CONTACT
www:
PRINT TECHNICAL DATA
CONTACT
HELP
W-K-M D
Y N AS
E A L®3 1 0 F
L O A T I N GB
A L LV
A L V E S(p124) P R O D U C T S P E C I F I C A T I O N S
How to Order
Size Port
Valve Body
Seal
Ball-Actuator Inches Reg=R
Type Tailpiece
Code Stem
Full=F Code Code Code
2 R B 1 3 6 C S 0 2 S 1 W R
Material Code Carbon Steel CS 316 Stainless Steel S1 Ni-Cu Alloy ML
17-4PH S2*
See Next Page
Standards and Specifications
DynaSeal 310 Ball Valves comply with the following design and testing standards: ANSI B16.5 (Steel Pipe Flanges and Flange Fittings), MSS-SP-6 (Standard Finishes for Pipe Flanges), MSS-SP-25 (Standard Marking System for Valves), MSS-SP-55 (Quality Standard for Steel Castings), API 607 (Fire Test Specification, Third Edition).
In addition, DynaSeal 310 Ball Valves can be supplied to comply with these standards: MSS-SP-72 (Ball Valves for
General Service), ANSI B31.1 (Power Piping), ANSI B31.3 (Chemical Plant and Petroleum Refinery Piping), API 598 (Valve Inspection and Testing), MSS-SP-61 (Pressure Testing of Steel Valves), ANSI B16.104 (Valve Seat Leakage)
DynaSeal 310 Ball Valves can be trimmed for sour gas service in accordance with NACE MR-01-75 (latest issue) and are available in both carbon steel and stainless steel.
Material Codes Carbon Steel CS Controlled hardness carbon steel CS2*
for H2S service
Same as CS2, but special for -50ºF service CS3*
316 stainless steel for wetted parts S1 316 stainless steel with stainless steel S8†
external trim. Good for -50ºF.
*Meets NACE specification MR-01-75.
†Meets NACE specification MR-01-75 in 3” bore size and smaller.
*NACE 2R and smaller. 17-4 PH Stem, 316 Stainless Steel Ball
Actuator Code Wrench WR Oval Handwheel OH Worm Gear WGA Bare Stem BS Less Gear L/G Seal Seal Material Tailpiece Gasket
Code Material 01 TFE TFE 01F TFE TFE 02 Filled TFE TFE 02F Filled TFE TFE 03 Delrin/HydrinTM TFE
07 VitonTM TFE
14 Filled TFE TFE 14F Filled TFE TFE
18 HPT-2 Filled TFE
23 CelconTM TFE
60 StelliteTM Filled TFE 60A StelliteTM Filled TFE 92H 316SS with chrome oxide and Filled TFE Filled TFE
CONTENTS MENU
CONTACT
www:
PRINT TECHNICAL DATA
CONTACT
HELP
Note: Threaded end valves have NPT internal pipe threads in full con-formance with ANSI B2.1 and Federal Thread Handbook H-28.
Note: R - Regular Port, F - Full Port, SP - Short Pattern, LP - Long Pattern
W-K-M D
Y N AS
E A L®3 1 0 F
L O A T I N GB
A L LV
A L V E SSize (in) Socket
Weld
Butt Weld Male
Thread Female
Thread
1/4 F B138 B138 B103 –
3/8 F B138 – – –
1/2 R B136 B136 B106 –
1/2 F B138 – – –
3/4 R B136 – – –
3/4 F B138 B138 B103 – 1 R B136 B136 B106 – 1 F B138 – – – 11/2F B138 – B103 – 2 R B136 – B106 – 2 F B138 – – B150 3 F B138 – – B150 4 R B136 – – B142 310C 3-Piece Valve Types (Threaded, Welded)
Size (in) 150RF 300RF
150RF 300RF Size (in)
LP SP
LP
4 F B110 – B128 – B150 6 R – B102 B120 – B142 6 F B110 B113 B128 – B150 8 R B100 B102 – B122 B142 8 F B110 – B128 B134 B150 10 R B100 – B120 – B142 10 F B110 – B128 B134 B150 12 R B100 – B120 – B142 12 F B110 – B128 – B150 14 R B100 – B120 – B142 310C 2-Piece Valve Types
310C 3-Piece Valve Types (Flanged)
310D Unibody and 2-Piece Valve Types
*1/2 F B112 B130
*3/4 R B102 B122
*1 R B102 B122
*1 F B112 B130
*11/2 R B102 B122 11/2 F B112 B130
*2 R B102 B122 2 F B112 B130
*3 R B102 B122 3 F B112 B130
*4 R B102 B122
300BW SP
Size (in) 150RF 300RF 600RF 600RJ
*Unibody Design.
1 R B100 B120 B114 B170 1 F B110 B128 B182 B172 11/2R B100 – B114 B170 11/2F B110 B128 B182 B172 2 R B100 B120 B114 B170 2 F B110 B128 B182 B172 3 x 2 B100 B120 B114 B170 3F B110 B128 B182 B172 4 x 3 B100 B120 B114 B170
CONTENTS MENU
CONTACT
www:
PRINT TECHNICAL DATA
CONTACT
HELP
W-K-M D
Y N AS
E A L®3 1 0 F
L O A T I N GB
A L LV
A L V E S(p126) P R O D U C T S P E C I F I C A T I O N S
The chart below is an abbreviated guide to the chemical resis-tance and pressure-temperature limitations of the seal materials
used in DynaSeal 310 Ball Valves. When in doubt about the trim selection consult your DynaSeal distributor or the factory.