This topic describes how to check whether the UA5000 can normally communicate with the router and whether the UA5000 can access the upper-layer device through the router.
4.1 Commissioning the U2000 Interconnection
The administrator can maintain and manage the UA5000 in inband network management or outband network management mode. This topic describes how to commission the
interconnection by considering the "iManager U2000 unified network management system" (iManager U2000) as an example.
4.1.1 Commissioning the U2000 in Outband Mode
This topic describes how to verify that the UA5000 can support the outband NMS through the local maintenance network port (the outband NMS interface), so that the iManager U2000 can maintain the device through this management channel.
Networking
Figure 4-1 shows that the iManager U2000 connects to the outband NMS interface of the PVMB control board in the UA5000 through the IP network.
Figure 4-1 Networking for the outband NMS
COM ETH1
PVMB
iManager U2000
UA5000 Router
ETH0
NOTE
l When the control board is PVMB, the iManager U2000 connects to the ETH0 maintenance network port of the PVMB control board through the IP network in the independent upstream mode. The iManager U2000 connects to the ETH1 service network port of the PVMB control board through the IP network in the integrated upstream mode.
l When the control board is PVMD, the iManager U2000 connects to the ETH maintenance network port of the active PVMD control board through the IP network in the independent upstream or the integrated upstream mode.
Data Plan
Table 4-1 provides the data plan of the outband NMS.
Table 4-1 Data plan for configuring the outband NMS
Device or Port Item Data
UA5000 outband
Name of the host that generates the trap
public
iManager U2000 IP address 10.10.1.1/24 Default gateway 10.10.1.10/24
l Configure the outband NMS on the UA5000 side.
1. Configure the MAC address of the outband NMS network port.
huawei(config)#mac outband add 02-E0-FC-02-02-03 active
2. Query the MAC address pool.
huawei(config)#display mac active
Index type MacAddress
0 Active 00-E0-FC-33-44-56
1 Active 02-E0-FC-02-02-03
3. Configure the IP address of the outband network port, gateway, and VLAN information.
huawei(config)#interface outband
huawei(config-outband)#ip address 10.20.1.2 255.255.255.0 10.20.1.1 vlan_tag 1001
4. Configure the working mode.
huawei(interface-outband)#quit huawei(config)#sysman mode outband
5. Configure the community name and the access authority.
huawei(config)#snmp-agent community read public huawei(config)#snmp-agent community write private
6. Enable the trap sending.
huawei(config)#snmp-agent trap enable standard
7. Configure the trap destination host name, IP address, and trap sending parameter list name.
huawei(config)#snmp-agent target-host trap-hostname public address 10.10.1.10 trap-paramsname public
huawei(config)#snmp-agent target-host trap-paramsname public v2c securityname public
8. Save the data.
huawei(config)#save
l Configure the outband NMS on the iManager U2000 side.
1. Set the following parameters on the iManager U2000.
– IP address: 10.10.1.1
– GET community name: public – SET community name: private
2. Configure the route gateway to network section 10.20.1.0/24 as 10.10.1.10.
NOTE
When the IP address of the UA5000 outband NMS interface is not in the same subnet as the IP address of the iManager U2000, you need to configure the route information to forward the NMS packet.
----End
Result
You can maintain and manage the device through the iManager U2000.
4.1.2 Commissioning the U2000 in Inband Mode
This topic describes how to verify that the UA5000 can realize the inband management through the uplink port (the inband management interface) so that the iManager U2000 can maintain the device through this management channel.
Networking
In the independent upstream mode, the iManager U2000 connects to the inband NMS interface ETH1 on the UA5000 through the IP network, as shown in Figure 4-2.
Figure 4-2 Networking for the inband NMS
COM ETH1
iManager U2000
UA5000 Router
ETH0
PVMB
NOTE
In the integrated upstream mode, the iManager U2000 connects to the internal network port of the PVMB/
PVMD control board through the IP network, and manages the device through the upstream network port of the IPMB/IPMD control board.
Data Plan
Table 4-2 provides the data plan for configuring the inband NMS.
Table 4-2 Data plan for configuring the inband NMS
Device or Port Item Data
NMS interface of the UA5000
IP address 10.20.1.3/24
Default gateway 10.20.1.1/24
NMS name huawei
GET community name public
SET community name private
vlan_tag 1001
Trap destination host name public Trap sending parameter list name public
Trap protocol version SNMP V2C
Device or Port Item Data Name of the host that generates the
trap
public
iManager U2000 IP address 10.10.1.1/24
Default gateway 10.10.1.10/24
NMS name huawei
GET community name public
SET community name private
Procedure
l Configure the inband NMS on the UA5000 side.
1. Configure the IP address of the inband NMS interface.
huawei(config)#interface eth
huawei(interface-eth)#ip address 10.20.1.3 255.255.255.0 10.20.1.1 vlan_tag 1001
2. Configure the community name and the access authority.
huawei(config))#snmp-agent community read public huawei(config)#snmp-agent community write private
3. Enable the trap sending.
huawei(config)#snmp-agent trap enable standard
4. Configure the trap destination host name, IP address, and trap sending parameter list name.
huawei(config)#snmp-agent target-host trap-hostname public address 10.10.1.10 trap-paramsname public
huawei(config)#snmp-agent target-host trap-paramsname public v2c securityname public
5. Save the data.
huawei(config)#save
l Configure the inband NMS on the iManager U2000 side.
1. Set the following parameters on the iManager U2000.
– IP address: 10.10.1.1.
– GET community name: public – SET community name: private
2. Configure the route gateway to subnet 10.20.1.0/24 as 10.10.1.10.
NOTE
When the IP address of the inband NMS interface is not in the same subnet of the iManager U2000, you need to configure the route for forwarding the IP packets.
----End
Result
You can maintain and manage the UA5000 through the iManager U2000.
4.2 Commissioning the MG Interface Interconnection
This topic describes how to commission the MG interface. The MG interface is an interface for the communication between the UA5000 and the MGC. This interface can use the H.248 or MGCP protocol. Before commissioning the service, you must commission the MG interface successfully.
4.2.1 Commissioning the MG Interface Interconnection (Through H.248)
This topic describes how to commission the MG interface so that the MG interface can communicate with the MGC through the H.248 protocol normally.
Prerequisite
l The UA5000 must work in the normal state.
l The IP address used in the example must be configured in the IP address pool through the ip address command.
l The data on the MGC, that is, the data corresponding to the data on the MG, and the data on the MG interface must be configured correctly.
l The system must be configured with the H.248 protocol.
l If the versions supported by the softswitch and the UA5000 are consistent, you need not configure the negotiated version. If the versions supported by the softswitch and the UA5000 are inconsistent, you need to run the if-h248 attribute command to configure the H.248 protocol for the MG interface to negotiate the version.
Networking
Figure 4-3 shows the networking for commissioning the MG interface through the H.248 protocol.
Figure 4-3 Networking for commissioning the MG interface through the H.248 protocol
UA5000
MGC 10.10.20.1/24 Router
10.10.10.1/24
H.248
P V M B
A S L 0/11 0/12
A S L
NOTE
The UA5000 supports the independent upstream transmission and the integrated upstream transmission modes. This commissioning task uses the independent upstream transmission mode. To use the integrated upstream transmission mode, run the working mode command to set the working mode of the PVMB board as the integrated upstream transmission mode.
Data Plan
Table 4-3 provides the data plan for commissioning the MG interface through the H.248 protocol.
Table 4-3 Data plan for commissioning the MG interface through the H.248 protocol
Item Data
MG interface mgid 0
protocol H.248
code text
transfer UDP
port 2944
domainname ua5000.com
IP address IP address of MG0 on the UA5000
10.10.10.2/24
Media IP address of MG0 on the UA5000
10.10.10.2/24
Default gateway of MG0 on the UA5000
10.10.10.1/24
MGC data IP address of the MGC 10.10.20.1/24
port 2944
protocol H.248
code text
transfer UDP
Procedure
Step 1 Add an MG interface.
huawei(config)#interface h248 0
Are you sure to add MG interface?(y/n)[n]:y huawei(config-if-h248-0)#
Step 2 Configure the parameters of the MG interface.
huawei(config-if-h248-0)#if-h248 attribute mgip 10.10.10.2 mgport 2944 code text transfer udp domainName ua5000.com primary-mgc-ip1 10.10.20.1 primary-mgc-port 2944 mg-media-ip1 10.71.46.69
Step 3 Restart the MG interface.
huawei(config-if-h248-0)#reset coldstart
Command:
reset coldstart Are you sure to reset MG interface?(y/n)[n]:y
huawei(config-if-h248-0)#quit
Step 4 Save the data.
huawei(config)#save
----End
Result
The MG and the MGC are connected successfully. Run the display if-h248 all command to query the status of the MG interface. The query result shows that the MG interface is in the normal state.
4.2.2 Commissioning the MG Interface Interconnection (Through MGCP)
This topic describes how to verify that the MG interface connection can communicate with the MGC successfully through the MGCP protocol.
Prerequisite
l The UA5000 must work normally.
l The ip address command must be executed to configure the IP address used in the example in the IP address pool.
l The data on the MGC, that is, the data corresponding to the data on the MG, and the data on the MG interface must be configured correctly.
l The protocol supported by the system must be configured to MGCP.
NOTE
You can run the display protocol support command to query the current voice protocol type. If the current voice protocol type is not MGCP, run the protocol support command to switch the voice protocol to MGCP.
Networking
Figure 4-4 shows the interconnection commissioning networking of the MG interface through the MGCP protocol.
Figure 4-4 Interconnection commissioning networking of the MG interface (over MGCP)
UA5000
MGC 10.10.20.1/24 Router
10.10.10.1/24
MGCP
10.10.10.2/24
P V M B
0/11 0/12
A S L
A S L
NOTE
The UA5000 supports the independent upstream mode and the integrated upstream mode. In the commissioning task, the independent upstream mode is used. In the case of the integrated upstream mode, you need to run the working mode command to set the working mode of the PVMB to integrated upstream mode.
Data Plan
Table 4-4 provides the data plan for the interconnection commissioning of the MG interface over MGCP.
Table 4-4 Data plan for the interconnection commissioning of the MG interface (over MGCP)
Item Data
MG interface mgid 0
protocol MGCP
port MG: 2427
MGC: 2727
domainname ua5000.com
IP address IP address of MG0 on the UA5000
10.10.10.2/24
IP address of the MGC 10.10.20.1/24
Procedure
Step 1 Add an MG interface.
huawei(config)#interface mgcp 0
Are you sure you want to add MG interface?(y/n)[n]:y huawei(config-if-mgcp-0)#
Step 2 Configure the parameters of the MG interface.
huawei(config-if-mgcp-0)#if-mgcp attribute mgip 10.10.10.2 mgport 2427 domainName ua5000.com mgcip_1 10.10.20.1 mgcport_1 2727
Step 3 Restart the MG interface.
huawei(config-if-mgcp-0)#reset
Are you sure to reset MG interface?(y/n)[n]:y huawei(config-if-mgcp-0)#quit
Step 4 Save the data.
huawei(config)#save
----End
Result
Run the display if-mgcp all command to query the status of the MG interface, and find that the status is in the normal state.
4.3 Commissioning the SIP Interface Interconnection
This topic describes how the UA5000 as the voice over IP gateway (VGW) communicates with the IMS through the SIP interface.
Prerequisite
l The voice protocol supported by the system must be configured to SIP.
NOTE
You can run the display protocol support command to query the current voice protocol type. If the voice protocol is not SIP, do as follows:
l When the control board is PVMD, run the protocol support command to switch the voice protocol to SIP.
l When the control board is PVMB, run the load program command and load data command to re-load the host program and the database file (corresponding to the SIP protocol), and then run the reboot command to restart the system to switch the voice protocol to SIP.
l The UA5000 must be in the normal state.
l The IP address (signaling IP address and media IP address) of the SIP interface must exist in the corresponding IP address pool. You can run the ip address command to configure the IP address of the SIP interface.
l After the configuration, you must run the reset(sip) command to reset the SIP interface to make the configuration data take effect. Otherwise, the configuration data is stored only in the database.
Networking
Figure 4-5 shows the example network for commissioning the interconnection with the SIP interface.
Figure 4-5 Example network for commissioning the interconnection with the SIP interface
The UA5000 supports the independent upstream mode and the integrated upstream mode. The commissioning task uses the independent upstream mode. If the integrated upstream mode is used, you need to run the working mode command to set the working mode of the PVMD board to integrated upstream mode.
Data Plan
In the commissioning task:
l Use the same IP address for the media stream and the signaling flow. Transmit the media stream and the signaling flow upstream through the same Ethernet port.
l Use the default QoS policy for the upstream transmission of the media stream and the signaling flow.
Table 4-5 shows the data plan for commissioning the interconnection with the MG interface through SIP.
Table 4-5 Data plan for commissioning the interconnection with the MG interface through SIP
Type Item Data
Upstream interface of the media stream and the signaling flow
0/4/0
Upstream VLAN of the media stream and signaling stream
VLAN ID: 1 (default)
Media/signaling IP address pool 10.13.4.116 Parameters of
the basic
The SIP interface ID 0
Type Item Data
IP address of the primary proxy server
10.13.4.110
Port ID of the primary proxy server 5555 IP address of the secondary proxy server
10.13.4.120
Port ID of the secondary proxy server
Domain name of the SIP interface huawei.com
Phone context +86755
Procedure
Step 1 Add an SIP interface.
huawei(config)#interface sip 0
Are you sure to add the SIP interface?(y/n)[n]:y
Step 2 Configure the basic attributes of the SIP interface.
huawei(config-if-sip-0)#if-sip attribute basic media-ip 10.13.4.116 signal-ip 10.13.4.116 signal-port 5555 transfer udp proxy-ip1 10.13.4.110 primary-proxy-port 5555
secondary-proxy-ip1 10.13.4.120 secondary-proxy-port 5555 home-domain UA5000.com sipprofile-index 1
Step 3 Configure the optional attributes of the SIP interface.
huawei(config-if-sip-0)#if-sip attribute optional mg-domain huawei.com phone-context +86755
Step 4 Query the configured attributes of the SIP interface.
huawei(config-if-sip-0)#display if-sip attribute config
Secondary Proxy Port 5555 Proxy address mode IP SIPProfile Index 1:Default
Service logic Index 0:Default Server Address DHCP Option 0:None
Primary Proxy Domain Name - Secondary Proxy Domain Name - Home Domain Name UA5000.com Description - MG Domain Name huawei.com Phone Context +86755 Register URI - Conference Factory URI - ---
Step 5 Reset the SIP interface.
huawei(config-if-sip-0)#reset huawei(config-if-sip-0)#quit
Step 6 Save the data.
huawei(config)#save
----End
Result
After the display if-sip attribute command is executed to query the current attributes of the SIP interface, it is found that the attributes of the SIP interface are the same as the configured attributes.
4.4 Commissioning the Interconnection Between the Device and the Router
This topic describes how to check whether the UA5000 can normally communicate with the router and whether the UA5000 can access the upper-layer device through the router.
Service Requirements
In the network as shown in Figure 4-6, the UA5000 uses the PVMB board for upstream transmission.
NOTE
For details about how to configure a router, see the related configuration guide.
Figure 4-6 Example network for commissioning the interconnection between the router and the device
COM ETH1
PVMB Router
10.50.1.1
UA5000
LAN
PC PC
PC
10.10.1.0/24
ETH0
Procedure
Step 1 Configure the IP address of the uplink port.
Configure the IP address of the uplink port to 10.50.1.10/24. The IP address of the uplink port and the IP address of the gateway (that is, the IP address of the router port that is connected to the UA5000) must be in the same network segment.
huawei(config)#interface eth
huawei(config-if-eth)#ip address 10.50.1.10 255.255.255.0 10.50.1.1 vlan_tag 1 huawei(config-if-eth)#quit
Step 2 Save the data.
huawei(config)#save
----End
Result
After the UA5000 is interconnected with the router successfully, you can ping IP address 10.10.1.0/24 from the UA5000.
5 Maintenance and Management Commissioning
About This Chapter
This topic describes how to verify the reliability of the device after commissioning the basic functions and services of the device to ensure the performance reliability of the UA5000.