Note: It is recommended that you use Import – Directory tasks (see page 29) for all supported devices and file types (see page 30) (including network state files and iXML files).
The import data format types supported by Skybox View are listed in the following table. The table also gives the relevant source file or folder required for the file import. The information in this table is used by the following file import task types: Import – Basic, Import – Advanced, Import – Collector, and Import – Collector Advanced.
Note: For Import – Basic tasks, you must specify the location of each file separately and not the folder. Format name Type of import data Source file or folder
A10 A10 Folder containing the following files:
• *.txt or *.log: The A10 configuration
Skybox View version 7.0.600 32
Format name Type of import data Source file or folder A10 routing table
AppDirector APPDIRECTOR Folder containing the following files:
• *.*: The AppDirector configuration
• (Optional) route.txt: Dump of the
AppDirector routing table
BIG-IP BIGIP
BlueCoat BLUECOAT Folder containing the following files:
• *.txt or *.log: The Blue Coat configuration
• (Optional) route.txt: Dump of the
Blue Coat routing table Cisco Router
Configuration (used for Cisco IOS and Cisco Nexus routers)
IOS_CONF Folder containing the following files:
• run.txt: The Cisco router configuration
• (Optional) route.txt: Dump of the
Cisco router routing table
Note: Import – Advanced and Import – Collector tasks can import the output of selected
subcommands of the ip route vrf *
command. If route.txt is not found in the
specified folder, the tasks process all files
named route_XXX.txt.
For example, execute the command show
ip route vrf connected and save the
output in route_connected.txt.
Cisco Security Manager Configuration
CSM_CONFIG_FILE Cisco Security Manager source file (*.xml)
EPO EPO
FireWall-1 Configuration
FW1_CONF Folder containing the following files:
• objects_5_0.c: The network objects
• rulebases_5_0.fws: The rulebase
• (Optional) install_statuses.c: The
statuses
• (Optional) vsx_objects.c: The VSX
device objects (from the vsx_slot_objects table)
Note: For Import – Basic tasks, any file names
with the appropriate extensions (*.c and
*.fws) are permitted. FortiGate Configuration file FORTIGATE_CONFIG_ FILE
Folder containing the following files:
• config.txt: The FortiGate configuration
• (Optional) route.txt: Dump of the
Skybox View version 7.0.600 33
Format name Type of import data Source file or folder Foundry
Configuration
FOUNDRY Folder containing the following files:
• run.txt: The Foundry configuration
• (Optional) route.txt: Dump of the
Foundry routing table FWSM
Configuration
FWSM_CONF Folder containing the following files:
• run.txt: The PIX/ASA/FWSM configuration
• (Optional) route.txt: Dump of the
PIX/ASA/FWSM routing table HFNetChk
Vulnerability Scanner Report
HFNETCHK Shavlik NetChk Protect Vulnerability
Scanner Report file (*.txt)
HP ProCurve HPPROCURVE Folder containing the following files:
• *.*: The ProCurve configuration
• (Optional) route.txt: Dump of the
ProCurve routing table HPOV Topology
Dump
HPOV_TOPODUMP HP Software & Solutions (OpenView)
topology dump file (*.txt)
Intermediate Security Model XML
INTERMEDIATE_XML iXML file (*.xml)
IpTables Configuration
IPTABLES Folder containing the following files:
• ifconfig.txt: The iptables interfaces configuration report
• filter.txt: The iptables filter table
• nat.txt: The iptables NAT table
• mangle.txt: The iptables mangle table
Junos Configuration file
JUNOS_CONFIG_FILE Folder containing the following files:
• config.txt: The Junos configuration
• (Optional) route.txt: Dump of the
Junos routing table McAfee
Enterprise Firewall
MCAFEEFIREWALL
nCircle Scan NCIRCLE (nCircle XML2) nCircle export XML file
(*.xml)
(nCircle XML3) Folder containing the following files:
• nCircle export XML (scan.xml)
• nCircle ASPL XML (aspl.xml)
Nessus Scan NESSUS_XML Nessus XML file (usually *.xml or
Skybox View version 7.0.600 34
Format name Type of import data Source file or folder NetScreen
Configuration file
NETSCREEN_CONFIG _FILE
Folder containing the following files:
• config.txt: The NetScreen configuration
• (Optional) route.txt: Dump of the
NetScreen routing table NetScreen
SNMP Dump file
NETSCREEN_SNMP_D UMP
NetScreen SNMP dump file (*.txt)
Network State HOST_ROUTING_AND
_INTERFACES
Folder containing the following files:
• netstat.txt: The network status report
• ifconfig.txt: The interfaces configuration report
NMap Scan NMAP_XML Nmap XML file (*.xml)
Nortel Bay 8600 Configuration
NORTEL_BAY Folder containing the following files:
• run.txt: The Nortel configuration
• (Optional) route.txt: Dump of the
Nortel routing table Palo Alto
Firewall Configuration
PALO_ALTO Folder containing the following files:
• config.xml: The Palo Alto configuration
• (Optional) route.txt: Dump of the
Palo Alto routing table PIX
Configuration
PIX_CONF Folder containing the following files:
• run.txt: The PIX/ASA/FWSM configuration
• (Optional) route.txt: Dump of the
PIX/ASA/FWSM routing table Provider-1
Configuration
PFW1_CONF Folder containing the following files:
• objects.c or objects_5_0.c: The CMA network objects
• rulebases.fws or
rulebases_5_0.fws: The CMA rulebase
• g_objects.c or g_objects_5_0.c: The global network objects
• (Optional) install_statuses.c: The
statuses
• (Optional) vsx_objects.c: The VSX
device objects (from the vsx_slot_objects table)
Note: For Import – Basic tasks, any file names
with the appropriate extensions (*.c and
*.fws) are permitted Qualys Map and
Scan
QUALYS Folder containing the following files:
Skybox View version 7.0.600 35
Format name Type of import data Source file or folder
• (Optional) map.xml: The Qualys Map
Rapid7 RAPID_7
Skybox Netmodel
SKYBOX_XML Skybox View XML file (*.xml)
Skybox Netmodel Encrypted
SKYBOX_XML_ENC Encrypted Skybox View XML file (*.xmlx)
SnmpWalk Configuration
SNMPWALK_DUMP SNMP walk dump file (*.*)
vShield Edge WSD SNMP Dump RADWSD_SNMP_DUM P WSD SNMP dump file (*.txt)