After an E3 Overload Relay is returned to normal following a trip reset, operation of Out A and Out B is determined by the state of the firmware latch. The output state matrix below details this.
Table 64 - Output State Matrix for Output Setup Parameters
Out X Output State
Commanded Output State
Prior to Trip PR FltState Setting PR FltValueSetting with Active Trip Last Commanded During Trip
Following Trip Reset (before any new command) Series A Series B & Later Open 0 = Go to FltValue 0 = Open Open Open Open Open
Close Closed Open -none - Open Open 1 = Closed Closed Open Open Closed
Close Closed Closed -none - Open Closed 1 = Ignore Fault — As Commanded
Close 0 = Go to FltValue 0 = Open Open Open Open Open
Close Closed Open -none - Closed Open 1 = Closed Closed Open Open Closed
Close Closed Closed -none - Closed Closed 1 = Ignore Fault — As Commanded
Table 65 - Output A Parameters Detail
OUTA PR FLTSTATE
This parameter, in conjunction with Parameter 66, defines how Output A will respond when a trip occurs. When set to “1”, Output A will continue to operate as commanded via the network. When set to “0”, Output A will open or close as determined by the setting of Parameter 66.
Parameter Number 65
Access Rule Get/Set
Data Type BOOL
Object Mapping 0x09-1-113
Group DeviceNet I/O
Units —
Minimum Value 0 = Go to FltValue (#66) Maximum Value 1 = Ignore Fault
Default Value 0
OUTA PR FLTVALUE
This parameter determines the state that Output A assumes when a trip occurs and Parameter 65 is set to “0”.
Parameter Number 66
Access Rule Get/Set
Data Type BOOL
Object Mapping 0x09-1-114
Group DeviceNet I/O
Units —
Minimum Value 0 = Open
Maximum Value 1 = Closed
Default Value 0
OUTA DN FLTSTATE
This parameter, in conjunction with Parameter 68, defines how Output A will respond when a DeviceNet network fault occurs. When set to “1”, Output A will hold the state prior to trip occurrence. When set to “0”, Output A will open or close as determined by the setting of Parameter 68.
Output A can be configured to go to a desired state in the event of a DeviceNet network fault independent from enabling CommFault in Parameter 24, Trip Enable.
Parameter Number 67
Access Rule Get/Set
Data Type BOOL
Object Mapping 0x09-1-5
Group DeviceNet I/O
Units —
Minimum Value 0 = Go to FltValue (#68) Maximum Value 1 = Hold Last State
Default Value 0
OUTA DN FLTVALUE
This parameter determines the state that Output A assumes when a DeviceNet network fault occurs and Parameter 67 is set to “0”.
Parameter Number 68
Access Rule Get/Set
Data Type BOOL
Object Mapping 0x09-1-6
Group DeviceNet I/O
Units —
Minimum Value 0 = Open
Maximum Value 1 = Closed
Default Value 0
OUTA DN IDLSTATE
This parameter, in conjunction with Parameter 70, defines how Output A will respond when the DeviceNet network is idle. When set to “1”, Output A will hold the state prior to trip occurrence. When set to “0”, Output A will open or close as determined by the setting in Parameter 70.
The Dn Flt parameters supersede the Dn Idl parameters.
Parameter Number 69
Access Rule Get/Set
Data Type BOOL
Object Mapping 0x09-1-7
Group DeviceNet I/O
Units —
Minimum Value 0 = Go to IdlValue (#70) Maximum Value 1 = Hold Last State
Table 66 - Output B Parameters Detail — E3 Plus
OUTA DN IDLVALUE
This parameter determines the state that Output A assumes when the network is idle and Parameter 69 is set to “0”.
Parameter Number 70
Access Rule Get/Set
Data Type BOOL
Object Mapping 0x09-1-8
Group Advanced Setup
Units —
Minimum Value 0 = Open
Maximum Value 1 = Closed
Default Value 0
OUTB PR FLTSTATE
This parameter, in conjunction with Parameter 72, defines how Output B will respond when a trip occurs. When set to “1”, Output B will continue to operate as commanded via the network. When set to “0”, Output B will open or close as determined by the setting in Parameter 72.
Parameter Number 71
Access Rule Get/Set
Data Type BOOL
Object Mapping 0x09-2-113
Group DeviceNet I/O
Units —
Minimum Value 0 = Go to FltValue (#72) Maximum Value 1 = Ignore Fault
Default Value 0
OUTB PR FLTVALUE
This parameter determines the state that Output B assumes when a trip occurs and Parameter 71 is set to “0”.
Parameter Number 72
Access Rule Get/Set
Data Type BOOL
Object Mapping 0x09-2-114
Group DeviceNet I/O
Units —
Minimum Value 0 = Open
Maximum Value 1 = Closed
Default Value 0
OUTB DN FLTSTATE
This parameter, in conjunction with Parameter 74, defines how Output B will respond when a DeviceNet network fault occurs. When set to “1”, Output B will hold the state prior to trip occurrence. When set to “0”, Output B will open or close as determined by the setting in Parameter 74.
Output B can be configured to go to a desired state in the event of a DeviceNet network fault independent from enabling CommFault in Parameter 24, Trip Enable.
Parameter Number 73
Access Rule Get/Set
Data Type BOOL
Object Mapping 0x09-2-5
Group DeviceNet I/O
Units —
Minimum Value 0 = Go to FltValue (#74) Maximum Value 1 = Hold Last State
Default Value 0
OUTB DN FLTVALUE
This parameter determines the state that Output B assumes when a comm fault occurs and Parameter 73 is set to “0”.
Parameter Number 74
Access Rule Get/Set
Data Type BOOL
Object Mapping 0x09-2-6
Group DeviceNet I/O
Units —
Minimum Value 0 = Open
Maximum Value 1 = Closed