StClass:
STCLASS_OK No error
STCLASS_ERROR_EDM
Error of the CSCWEDM.DLL
StCode:
20008101 EDM_VEM_NOT_INIT Reason:
EDM not initialized. Application: Initialize EDM Measure:
If the message recurs, replace or check the EDM. 20008102 EDM_INVALID_BLK_LEN
Reason:
The length specified in the parameter block for the "CscDhlPara.InLen" input buffer or for the "CscDhlPara.OutLen" output buffer cannot be divided by eight.
Application:
Check the application program. 20008103 EDM_INVALID_CMD
Reason:
The DLL command specification is invalid. Application:
Encryption/Decryption module (EDM)
20008104 EDM_INVALID_PARA Reason:
The command parameters are incorrect. Application:
Check the command parameters in the application program. 20008105 EDM_INVALID_KEY_NO
Reason:
Invalid key number. Application:
Check key number in application program. 20008107 EDM_INVALID_FRM_DATA
Reason:
Error during data transmission. Application:
Issue job again. Check application program, if necessary. Measure:
Check firmware version. 2000810B EDM_INVALID_IV_LEN
Reason:
Initialize vector has wrong length (not eight). Application:
Check application program. 2000810C EDM_NO_IV_SPACE
Reason:
No free space in IV array (internal error) Application:
Encryption/Decryption module (EDM)
2000810E EDM_MEMORY_ALLOC_ERROR Reason:
System could not provide dynamic memory. Application:
Reboot system. Measure:
Check memory configuration of PC hardware and disk space. 20008111 EDM_PIN_INVALID_MAX_LEN
Reason:
Wrong maximum PIN length with job "EdmStartPin". Application:
Check application program. 20008112 EDM_PIN_INVALID_MIN_LEN
Reason:
Wrong minimum PIN length with job "EdmStartPin". Application:
Check application program.
20008113 EDM_PIN_INVALID_ZERO_CMD Reason:
An invalid field for leading zeros is in the PIN structure with job "EdmStartPin". Application:
Check application program.
20008114 EDM_PIN_INVALID_QUIT_CMD Reason:
An invalid field for "acknowledge key" is in the PIN structure with job "EdmStartPin". Application:
Check application program. 20008115 EDM_PIN_INVALID_MODE
Reason:
Invalid mode in the PIN structure. Application:
Encryption/Decryption module (EDM)
20008116 EDM_PIN_INVALID_POS Reason:
Wrong PIN position in PIN field (validation data). Application:
Check application program.
20008118 EDM_PIN_INVALID_TESTMODE Reason:
Wrong structure entry in field "TestMode". Application:
Check application program. 20008119 EDM_PIN_INVALID_PINLEN
Reason:
Invalid number of PIN digits. Application:
Check application program. 2000811A EDM_DLL_INVALID_API
Reason:
This API is not supported by the device handler. Application:
Check application program. Measure:
Check DLL release. Check firmware version.
2000811B EDM_DLL_PROC_NOT_FOUND Reason:
The API could not be loaded. Application:
Check application program. Measure:
Check DLL release.
Encryption/Decryption module (EDM)
2000811C EDM_DLL_ACCESS_DENIED Reason:
This function cannot be accessed with the firmware used in the ENCRYPTION/DECRYPTION MODULE.
Application:
Check application program Measure:
Check DLL release. Check firmware version.
2000811E EDM_INVALID_DATA_ACCESS Reason:
Cannot access full length of data area in a structure. Application:
Check application program 2000811F EDM_INVALID_IV_MODE
Reason:
Invalid encryption mode specified for key reset. Application:
Check application program 20008120 EDM_PROTOCOL_TIMEOUT
Reason:
The total protocol monitoring time has been exceeded. Application:
Repeat the command and if necessary initialize the device again beforehand. Measure:
Check the hardware.
20008121 EDM_MAX_RX_RETRIES Reason:
The maximum number of receive repeats has been reached. Application:
Repeat the command and if necessary initialize the device again beforehand. Measure:
Encryption/Decryption module (EDM)
20008122 EDM_INVALID_ACK_TYPE Reason:
The received acknowledge type is invalid (only ACK and NAK are valid). Application:
Repeat the command and if necessary initialize the device again beforehand. Measure:
Check the hardware.
20008123 EDM_PROTOCOL_ERROR Reason:
Common protocol error in EPP response data. Application:
Repeat the command and if necessary initialize the device again beforehand. Measure:
Check the hardware if necessary. 20008124 EDM_INVALID_PAIR_OF_KGK
Reason:
Key Generating Keys in REGISTRY/CSC.INI are not correct. Application:
Correct Keys. Measure:
Check the REGISTRY or CSC.INI. 20008125 EDM_INVALID_KGK_VALUE
Reason:
Invalid character in KGK Keyset in REGISTRY/CSC.INI. Application:
Correct Keys. Measure:
Encryption/Decryption module (EDM)
20008126 EDM_ERROR_MK_CHECK Reason:
Error when encrypting a Masterkey. Application:
Enter or load correct Masterkey. Measure:
Check the REGISTRY or CSC.INI. 20008127 EDM_INVALID_MAC
Reason:
The check of the CFB-MAC via the EF_INFO data field of the chip card is negative. Faulty or wrong chip card.
Application:
The sequence may have to be started once more. 20008128 EDM_ALREADY_IN_USE
Reason:
The EPP is in use. This command cannot be processed in this state. Application:
Close all processes using the EPP. 20008129 EDM_MALLOC_ERROR
Reason:
There is not enough memory. Application:
Close all processes using the EPP. 2000812A EDM_KEYTABLE_FULL
Reason:
The key table is full. Application:
Delete the keys that are not required. 2000812B EDM_INVALID_KEYNAME
Reason:
Encryption/Decryption module (EDM)
2000812C EDM_IMPORT_WRONG_TYPE Reason:
It is not allowed to import an 8 byte DES key as an importer key. Application:
Use a 16 byte key.
2000812D EDM_BUFFER_OVERFLOW Reason:
Over the PIN device (keyborad) more than 15 indications were entered within a certain time interval.
Application:
System overload. The input characters could not be evaluated in time by the ATM. 20008202 EDM_APSS_INVALID_KEY_TYPE
Reason:
The key number or the key type is wrong. Application:
Use the correct key or key type. 20008300 EDM_FRMLD_IN_PROGRESS
Reason:
The firmware load function is running. Application:
Wait for the end of the load function. 20008301 EDM_FRMLD_NBR
Reason:
No block received. Measure:
Check the hardware. 20008302 EDM_FRMLD_RNR
Reason:
Receiver not ready. Measure:
Encryption/Decryption module (EDM)
20008303 EDM_FRMLD_SNR Reason:
Sender not ready. Measure:
Check the hardware. 20008304 EDM_FRMLD_DIST
Reason: Line disturbed. Measure:
Check the hardware. 20008305 EDM_FRMLD_FORMAT
Reason:
The command block has a wrong format. Measure:
Report the error log of this entry to Service. 20008306 EDM_FRMLD_LOADER
Reason:
Unknown loader error. Measure:
Report the error log of this entry to Service. 20008307 EDM_FRMLD_CMDSEQ
Reason:
Illegal command sequence. Measure:
Report the error log of this entry to Service. 28008000 EDM_FRM_UNDEF_ERROR
Reason:
An undefined internal error has occurred in the firmware. Measure:
Encryption/Decryption module (EDM)
28008001 EDM_FRM_CMD_NOT_EXEC Reason:
The firmware cannot execute the command. Measure:
Command number, check EDM status, enter PIN ready. 28008002 EDM_FRM_INVALID_KEY
Reason:
Key address (key number) not allowed (internal error). Application:
Correct key number. Measure:
Check EDM firmware release. 28008003 EDM_FRM_RAM_ERROR
Reason:
EDM RAM error (internal hardware error). Measure:
Replace EDM/EPP
28008004 EDM_FRM_PARITY_ERROR Reason:
Parity error in key. Measure:
Check key address and load again, if necessary.
This is a warning following a "load key" command. Wrong parity of loaded key. Parity was corrected by EDM/EPP, and key was loaded to specified address.
28008005 EDM_FRM_EPROM_ERROR Reason:
Internal hardware E-PROM error. Measure:
Encryption/Decryption module (EDM)
28008006 EDM_FRM_EEPROM_ERROR Reason:
Internal hardware EE-PROM error. Measure:
Replace EDM/EPP
28008007 EDM_FRM_CMD_NOT_EXIST Reason:
The EDM command does not exist (internal error). Measure:
Check EDM firmware release. 28008008 EDM_FRM_KEY_RAM_ERROR
Reason:
The EDM key RAM is defective (internal error). Measure:
Check EDM and replace if necessary. 28008009 EDM_FRM_LENGTH_ERROR
Reason:
The transferred data length is invalid (internal error). Measure:
Check EDM firmware release. 2800800A EDM_FRM_BLOCK_IDENT
Reason:
An invalid block ID is in the V.24 protocol (internal error). Measure:
Check EDM firmware release. 2800800B EDM_FRM_DEVICE_ID
Reason:
The device ID is invalid (internal error). Measure:
Encryption/Decryption module (EDM)
2800800C EDM_FRM_COMMAND_ACTIVE Reason:
A command has already been transferred for processing to the EDM firmware. Application:
Retry job after a certain time.
2800800D EDM_FRM_DATA_LENGTH_ERR Reason:
Command length and data length invalid (internal error). Measure:
Check EDM firmware release. 2800800E EDM_FRM_OUTPUT_PARA
Reason:
Output parameters not defined (internal error). Measure:
Check EDM firmware release. 2800800F EDM_FRM_UNDEF_DATA
Reason:
Data contains invalid ASCII characters (internal error). Measure:
Check EDM firmware release. 28008010 EDM_FRM_CHECKSUM_ERROR
Reason:
Wrong sequence of commands. The EDM status is not "READY". Application:
Encryption must be preceded by a positive checksum test. Check application program. 28008011 EDM_FRM_ID_ERROR
Reason:
Wrong ID. The entered (encoded) ID is not correct. Application:
Encryption/Decryption module (EDM)
28008040 EDM_FRM_TRANSAC_N_ACTIVE Reason:
No transaction active, command cannot be executed. Application:
Start transaction.
28008041 EDM_FRM_INVALID_PINLEN Reason:
No or not enough PIN numbers entered. Application:
Repeat command.
28008045 EDM_FRM_KEY_EXISTS Reason:
The key with this name exists already in the EPP. Application:
Delete the key with the export command or use a different key name. 28008046 EDM_FRM_KEY_NOT_FOUND
Reason:
The key with this name is not loaded in the EPP. Application:
Use the correct key.
28008047 EDM_FRM_KEY_NOT_ALLOWED Reason:
The use of this key for this function is not allowed. Application:
Use the correct key.
28008048 EDM_FRM_NO_RSA_PROCESSOR Reason:
There is no RSA processor in the EPP. Measure:
Encryption/Decryption module (EDM)
28008049 EDM_FRM_WRONG_RSA_KEY_LEN Reason:
The modulus length of the RSA key is not ok. Application:
Use the correct length.
28008050 EDM_FRM_SP_EPROM_ERROR Reason:
Key-splitting E-PROM not connected or wrong. Measure:
Check EDM. Install PROM.
28008051 EDM_FRM_SP_CHECK_ERROR Reason:
Checksum of key-splitting E-PROM is wrong. Measure:
Check hardware and E-PROM contents. 28008052 EDM_FRM_SP_PARITY_ERROR
Reason:
Parity error in key of the key-splitting E-PROM. Application:
Load correct key. Measure:
Check hardware and E-PROM contents. 28008053 EDM_FRM_SP_TABLE_ERROR
Reason:
Invalid table character in key-splitting E-PROM. Measure:
Check hardware and E-PROM contents. 28008060 EDM_FRM_X_ERROR
Reason:
Encryption/Decryption module (EDM)
28008061 EDM_FRM_BATTERY_EMPTY Reason:
The minimum battery current flows out of the internal control window of the connected EPP. Measure:
Have the hardware checked by service. 28008062 EDM_FRM_KEY_ENTRY_ERROR
Reason:
The EPP detects an error when entering a key by use of the EPPs key pad. Measure:
Repeat carefully the complete key entry procedure.
If the error occurs again, there might be a wrong key set. Initialize the EPP, enter a new transport key. Have the hardware checked by service.
28008063 EDM_FRM_APSS_KEY_ERROR Reason:
The EPP detects an error when loading a key in APSS mode. Application:
Use the correct key.
28008064 EDM_FRM_WRONG_KEK Reason:
The EPP detects an error when loading a key. Application:
Use the correct importer key or load the importer key. 28008065 EDM_FRM_SCOP_AUTHENTICATE
Reason:
The EPP detects an error when authenticating the SCOP chip card. Measure:
Check if the chipcard in the SCOP controller is wrong. 28008066 EDM_FRM_SCOP_PARA_TYPE
Reason:
The EPP detects an error when loading the SCOP parameters. One Type is wrong. Application:
Encryption/Decryption module (EDM)
28008067 EDM_FRM_SCOP_PARA Reason:
The EPP detects an error when loading the SCOP parameters. One sequence is wrong. Application:
Load the correct sequence.
28008068 EDM_FRM_SCOP_PARA_LENGTH Reason:
The EPP detects an error when loading the SCOP parameters. The length is wrong. Application: