This document is for problem-solving by only authorized people.
NAVI AUDIO FHD HDD DVD MECHA FAN FFC DISP UNIT
Workset 1 - - - - - Inspect and connect system. - - - - - - - - -
-Less than or equal to 500µA after 10 seconds
Applicable for only ACM. 1 1 - - -
-3
(68P)
-Less than or equal to 1.5mA after 10 seconds
Applicable for only ACM. - - - - - - -
-Less than or equal to 2A
Applicable for only ACM. 1 1 - 4 3 5
6
(All)
-Less than or equal to 5A
Total of ACM, Display, EFP - - - - - - -
-XTP
Startup Confirmation 4 - - - - CPU Test
Turn On [+B] 1st then [ACC], then begin CPU check
XTP must start and the Hitanykey prompt must appear. If a key is input after the Hitanykey prompt appears, the xanavi> prompt must appear.
Hitanykey
(A key is input after Hitanykey appears.) xanavi>
- - - - - - -
-5 xtp 100 15 - Display Boot Version Version Confirmation Loading Specification
xanavi>xtp 100 15
(100) Main CPU TEST START...
-6 xtp 100 18 - Display APP Version HDD Master Specification as well as Loading
Specification
xanavi>xtp 100 18
(100) Main CPU TEST START...
FLA_AP VER = B1U***** ...END(Main CPU )
1 - 3 2 - - 4
(50P)
-7 xtp 700 13 - Display Map Version HDD Master Specification
xanavi>xtp 700 13
(700) CD-ROM TEST START...
MAP FORMAT VERTION = FORMAT VERSION X07-00-00 MAP DATA VERTION = DATA VERSION 07/10/22/01
...END(CD-ROM )
-8 xtp 700 43 - Display RippingDSP(DA610)
Version Loading Specification
xanavi>xtp 700 43
(700) CD-ROM TEST START...
DSP FIRMWARE = ******* ...END(CD-ROM )
1 - 3 2 - - 4
(50P)
-HDD MODEL =TOSHIBA MK4036GAC HDD SERIAL =17JBT1T5T
HDD REVISION=TA151A
xanavi>xtp 700 42
(700) CD-ROM TEST START...
-HDD MODEL =Hitachi HEJ425040F9AT00 HDD SERIAL =F40201FSG1L4HB HDD REVISION=F4CJA30F
xanavi>xtp 700 42
(700) CD-ROM TEST START...
HDD MODEL = Hitachi HEJ425040F9AT00 HDD SERIAL = F40201FSG1L4HB
HDD REVISION = F4CJA30F ...END(CD-ROM )
- - - - - - -
-10 xtp 700 41 - Display DVD Firmware Version DVD Mechanism Drawing
xanavi>xtp 700 41
(700) CD-ROM TEST START...
DVD REVISION = **** ...END(CD-ROM )
3 - - - 1 - 2
(40&45P)
-11 xtp 400 60 - MS-CAN micro software version
indication CAN Micro Loading Specification
xanavi>xtp 400 60
(400) Communication TEST START...
[FNOS] SubCPU Version[36,04,6101309]
...END(Communication)
1 - - - - - -
-12 xtp 600 11 - GPS version indication J78E301
xanavi>xtp 600 11
(600) Sensor TEST START...
GPS VERSION = J78E301 ...END(Sensor )
1 - - - - - -
-13 xtp 900 65 - Audio CPU software version
indication AUDIO Circuit Board Drawing
xanavi>xtp 900 65
(900) AV TEST START...
AHU SOFT VER = 0x000230 ...END(AV )
2 1 - - - - 3
(68P)
-14 xtp 900 66 Audio CPU hardware version
indication AUDIO Circuit Board Drawing
xanavi>xtp 900 66
(900) AV TEST START...
AHU HARD VER = 0x000002 ...END(AV )
2 1 - - - - 3
(68P)
-15 xtp 100 39 - Sirius version indication AUDIO Circuit Board Drawing
xanavi>xtp 100 39
(100) Main CPU TEST START...
XM(SIRIUS) RADIO FIRMWARE VERSION = ******
...END(Main CPU )
2 1 - - - - 3
(68P)
-DP8W-4200 Copying Specification xanavi>xtp 400 30
Judgement Reference XTP Log Output Example
Set Power Supply (+B) to 12.8V±
0.2V and measure current.
-
- HDD Version Indication
-Inspection Item(Method)
Turn On Dengen Box's ACC switch and measure current after 10 seconds.
Consumption Current Check XTP Item Name
Dark Current Check
-9 xtp 700 42
Consumption
Current 3 -
-Dark Current
Category No. Command
2
-Parameter 1
-Parameter 2 Parameter 3 and after
-
-Version Confirmation
Part to Replace
Xanavi confidential
NAVI AUDIO FHD HDD DVD MECHA FAN FFC DISP UNIT
17 xtp 900 73 - Audio CPU communication check
Confirm communication between Navi Board CPU and Audio Board CPU.
OK if no error detected
xanavi>xtp 900 73
(900) AV TEST START...END(AV )
NO ERROR DETECTED...OK!
2 1 - - - - 3
(68P)
-18 xtp 600 1 - GPS tuner communication check Confirm communication between
Navi Board CPU and GPS Tuner.OK if no error detected
xanavi>xtp 600 1
(600) Sensor TEST START...END(Sensor ) NO ERROR DETECTED...OK!
1 - - - - - -
-19 xtp 600 14 - GPS antenna connection check GPS antenna connection check
GPS ANT STATUS = CONNECTED
GPS ANT STATUS = OPEN
GPS ANT STATUS = SHORT
xanavi>xtp 600 14
(600) Sensor TEST START...
GPS ANT STATUS = CONNECTED ANT AD VOL AD VAL = 00798
ANT 84AD VOL AD VAL = 00844 ...END(Sensor )
xanavi>xtp 600 14
(600) Sensor TEST START...
GPS ANT STATUS = O
1 - - - - - -
-20 xtp 400 9 - Display communication check Confirm communication between Navi Board CPU and Display.
OK if no error detected
* This test is not necessary when performing a display visual check
xanavi>xtp 400 9
(400) Communication TEST START...END(Communication) NO ERROR DETECTED...OK!
1 - - - - - - 2
21 xtp 400 22 - Sirius tuner communication check
Confirm communication between Navi Board CPU and Sirius Tuner.
OK if no error detected
xanavi>xtp 400 22
(400) Communication TEST START...END(Communication) NO ERROR DETECTED...OK!
2 1 - - - - 3
(68P)
-22 xtp 400 23 - Sirius antenna connection check Sirius antenna connection check OK if no error detected
xanavi>xtp 400 23
(400) Communication TEST START...END(Communication) NO ERROR DETECTED...OK!
2 1 - - - - 3
(68P)
-23 xtp 700 1 - HDD self-diagnosis Begin Self-Diagnosis OK if no error detected
xanavi>xtp 700 1
(700) CD-ROM TEST START...END(CD-ROM ) NO ERROR DETECTED...OK!
3 - 2 1 - - 4
(50P)
-24 xtp 700 15 - HDD disc check
(Partition 1)
Perform Disc Check (Partition 1)
bad cluster=0,lost cluster=0, cross point=0,lost chain=0, bad lfns=0
xanavi>xtp 700 15
(700) CD-ROM TEST START...
(Partition 2)
Perform Disc Check (Partition 2)
bad cluster=0,lost cluster=0, cross point=0,lost chain=0, bad lfns=0
xanavi>xtp 700 16
(700) CD-ROM TEST START...
(Partition 3)
Perform Disc Check (Partition 3)
bad cluster=0,lost cluster=0, cross point=0,lost chain=0, bad lfns=0
xanavi>xtp 700 17
(700) CD-ROM TEST START...
(Partition 4)
Perform Disc Check (Partition 4)
bad cluster=0,lost cluster=0, cross point=0,lost chain=0, bad lfns=0
xanavi>xtp 700 18
(700) CD-ROM TEST START...
-28 xdsp 1 - - SDRAM memory check Ripping DSP SDRAM
Perform memory check OK if no error detected xanavi>xdsp 1
NO ERROR DETECTED...OK! 1 - - - - - -
-29 xtp 100 45 - Ripping DSP Register check Ripping DSP resgister
Read/Write check OK if no error detected
xanavi>xtp 100 45
(100) Main CPU TEST START...END(Main CPU ) NO ERROR DETECTED...OK!
1 - - - - - -
-Category No. Command Parameter 1 Parameter 2 Parameter 3 XTP Item Name Inspection Item(Method) Judgement Reference XTP Log Output Example Part to Replace
Main CPU Check Communication /Connection Confirmation
Xanavi confidential
NAVI AUDIO FHD HDD DVD MECHA FAN FFC DISP UNIT
30 xtp 100 46 - Sub-CPU self-diagnosis internal ROM/RAM, register R/W
perform check OK if no error detected
xanavi>xtp 100 46
(100) Main CPU TEST START...END(Communication) NO ERROR DETECTED...OK
1 - - - - - -
-31 xtp 400 62 - CAN_IF communication check Between Sub-CPU-DCU's CAN
Command I/O check OK if no error detected
xanavi>xtp 400 62
(400) Communication TEST START...END(Communication) NO ERROR DETECTED...OK
1 2 - - - - 3
(68P)
-32 xtp 700 70 - DVD mechanism Model/Region
Code indication
DVD mechanism Model/Region Code indication
MODEL =6 REGION =10
xanavi>xtp 700 70
(700) CD-ROM TEST START...
MODEL =6 REGION =10
3 - - - 1 - 2
(40&45P)
-33 xtp 700 71 - DVD mechanism temperature
indication
DVD mechanism's temperature
sensor readout DVD TEMP= XX is displayed
xanavi>xtp 700 71
(700) CD-ROM TEST START...
DVD MECHA TEMP = 47 ...END(CD-ROM )
3 - - - 1 - 2
(40&45P)
-34 xtp 700 14 - HDD Temperature indication HDD's temperature sensor readout
HDD TEMP= XX is displayed
Compare results to DVD Mechanism Temperature Sensor Information (No.32)
The difference in temperature is equal to or less than 5 degrees.
xanavi>xtp 700 14
(700) CD-ROM TEST START...
HDD TEMP = 47
...END(CD-ROM )
3 - 2 1 - - 4
(50P)
-35 xtp 700 55 - HDD_ATA_RESET HDD's ATAPI reset OK if no error detected
xanavi>xtp 700 55
(700) CD-ROM TEST START...END(CD-ROM ) NO ERROR DETECTED...OK!
3 - 2 1 - - 4
(50P)
-Graphics
Check 36 xtp 500 11 Gray scale indication Perform gray scale indication command
Gray scale should not be abnormal.
* This test is not necessary when performing a display visual check
xanavi>xtp 500 11
(500) Graphic TEST START...END(Graphic ) 1 - - - - - - 2
Vehicle
Signal Input 37 xtp 300 48
-Vehicle signal input status indication
[RV][Start]
Operate the [RV] and [START]
switches on the Dengen Box
Change the input signal status by toggling the Dengen box [RV] and [START] switches
xanavi>xtp 300 48
(300) I/O TEST START...
-38 xtp 300 110 - Display_Enable Control
LOW setting Display power OFF Video Enable signal (28PIN, J2-4) is less than or equal to 0.6V
xanavi>xtp 300 110
(300) I/O TEST START...
Disp Enable = L ...END(I/O )
1 - - 2
39 xtp 300 111 - Display_Enable Control
HIGH setting Display power ON Video Enable signal (28PIN, J2-4) is more than or equal to 4.0V
xanavi>xtp 300 111
(300) I/O TEST START...
Disp Enable = H ...END(I/O )
1 - - 2
40 xclw GPS Clock Write
Set time on GPS tuner
* To convert to GMT (Japan Time -9 Hours)
Confirm all lower case letters displayed
"!!a !!e !!b !!e !!c !!e"
Error if UPPER CASE LETTERS are displayed
xanavi>xclw 7 5 16 20 5 10 xanavi>!!a
-41 xtp 600 12 - GPS Satellite Acquisition
Indication
Receive signal from GPS Antenna and confirm total number of satellites.
Additional satellites not less than 2
xanavi>xtp 600 12
(600) Sensor TEST START...
SATELLITE = 5 ...END(Sensor )
1 - - - - - -
-42 xtp 600 13 GPS A0 status indication GPS A0 Status Indication
GPS A0 STATUS parameters apply to the following 3 types
00: 3-d positioning (default sensor without correction)
20: 2-d positioning (default sensor without connection)
5x: positioning is currently not available, latest available position data
* "x" is any hexadecimal character
xanavi>xtp 600 13
(600) Sensor TEST START...
GPS A0 STATUS = 00
...END(Sensor )
1 - - - - - -
-43 xtp 800 48 - Begin Continuous Sine Wave
Output
Begin 1kHz reference wave
output - xanavi>xtp 800 48
(800) Voice TEST START...END(Voice ) 1 2 - - -
-3
(68P)
-44 xmcu Adjust Sine Wave Volume Perform volume adjustment
command - xanavi>xmcu 2 4 5 0x18 2 1 - - - - 3
(68P)
-45 xtp 800 4 - Voice Recognition AD Check Perform Voice Recognition AD check command
Actual values are within the following range:
(decimal notation)
Maximum 14500 < Actual Value < 18000 Minimum -18000 < Actual Value <-14500
xanavi>xtp 800 4
(800) Voice TEST START...
-46 xtp 800 49 - Stop continuous Sine Wave
Output Stop 1kHz reference wave output - xanavi>xtp 800 49
(800) Voice TEST START...END(Voice ) 1 2 - - -
-3
(68P)
-[Year][Month][Day][HOur]
[Minute][Second]
Voice Guidance Output /Voice Check
2 4 5 0x18 GPS
Category No. Command Parameter 1 Parameter 2 Parameter 3 XTP Item Name Inspection Item(Method) Judgement Reference XTP Log Output Example Part to Replace
HDD (IDE)
Control Signal Output DVD Mechanism
Sub-CPU Check
Xanavi confidential
NAVI AUDIO FHD HDD DVD MECHA FAN FFC DISP UNIT
Test Bit Input
Status Check 47 xtp 100 11 - Test Bit input status indication Turn On and Off the 3 Test Bit
switches on the Dengen Box Test bit input signal status display is correct
xanavi>xtp 100 11
(100) Main CPU TEST START...
TEST0 = L TEST1 = L TEST2 = L ...END(Main CPU ) xanavi>xtp 100 11
(100) Main CPU TEST START...
TEST0 = L TEST1 = L TEST2 = H ...END(Main CPU ) xanavi>xtp 100 11
(100) Main
1 - - - - - -
-48 xtp 900 88 - Fan ON (Normal Speed) FAN spins Fan is spinning xanavi>xtp 900 88
(900) AV TEST START...END(AV ) - 2 - - - 1 -
-49 xtp 900 62 - Fan ON(High Speed) FAN spins at high speed Fan air flow increases xanavi>xtp 900 62
(900) AV TEST START...END(AV ) - 2 - - - 1 -
-50 xtp 900 63 - Fan OFF FAN does not spin Fan is not spinning xanavi>xtp 900 63
(900) AV TEST START...END(AV ) - 2 - - - 1 -
-51 xtp 300 102 - P-HOLD signal LOW control
(P-HOLD=OFF) P-HOLD signal is turned Off. 1 - - - - - -
-52 xtp 300 104 - P-HOLD signal status check Confirm P-HOLD=LOW 1 - - - - - -
-53 xtp 300 103 - P-HOLD signal HIGH control
(P-HOLD=ON) P-HOLD signal is turned On 1 - - - - - -
-54 xtp 300 104 - P-HOLD signal status check Confirm P-HOLD=HIGH 1 - - - - - -
-55 xtp 300 102 - P-HOLD signal LOW control
(P-HOLD=OFF) P-HOLD signal is turned Off. - xanavi>xtp 300 102
(300) I/O TEST START...END(I/O ) 1 - - - - - -
-EQ File Check 56 xrfpn 2 6 3721 2 EQ file indication
Confirm Part Number Table Number EQ version output
EQ model reference Refer to drawing
xanavi>xrfpn 2 6 3721 2
### EQ Configuration Part Number HDD LIST
---### Part Number 9L3T-14D660-AA
### 39 4c 33 54 2d 31 34 44 36 36 30 2d 41 41 00 00 00 00 00 00 00 00 00 00
### Table Number 00 00 00 00
### E2PROM Ver
1 2 - 3 - - 4
(50P)
-Gyro 57 xtp 600 31 - Gyro A/D conversion indication Confirm in rest state and Gyro
output value GYRO A/D = 18830 ~ 22110
xanavi>xtp 600 31
(600) Sensor TEST START...
GYRO A/D = 20498 ...END(Sensor )
1 - - - - - -
-Process Termination 58 xtp 700 9 - Preparation to turn OFF Dengen Box
Preparation to turn OFF Dengen
Box OK if no error detected
xanavi>xtp 700 9
(700) CD-ROM TEST START...END(CD-ROM ) NO ERROR DETECTED...OK!
2 3 1 4
(50P)
-End Inspection 59 - - - - Turn OFF ACC 1st then +B then
disconnect unit - - - - - - - - - -
-Category No. Command Parameter 1 Parameter 2 Parameter 3 XTP Item Name Inspection Item(Method) Judgement Reference XTP Log Output Example Part to Replace
Confirm acquisition of Low FAN
P-HOLD
xanavi>xtp 300 102
(300) I/O TEST START...END(I/O ) xanavi>xtp 300 104
(300) I/O TEST START...
P-HOLD STS = LOW ...END(I/O )
xanavi>xtp 300 103
(300) I/O TEST START...END(I/O ) xanavi>xtp 300 104
(300) I/O TEST START...
P-HOLD STS = HIGH ...END(I/O ) Confirm acquisition of High
Xanavi confidential
Ford part number or other ID setting
Applicable Models: NAU-4200,NA6W-4200B (and others) This document is for problem-solving by only authorized people.
Center Stack Brick
Work set 1 - - - - - - - - -
(chassis ID last 8 digits)
password - - - xanavi>xcpl 1 0xf1 0x00000001 password
unit id = OK WRITE [F100000001]
5 xcpl 2 - - - - -
-xanavi>xcpl 2
unit id FLASH = OK READ [F100000001]
unit id HDD = OK READ [F100000001]
6 xrudac 3 1 password - - - - xanavi>xrudac 3 1 password
UDAC SERIAL ID = OK CLEAR
7 xrudac 3 2 password - - - - xanavi>xrudac 3 2 password
UDAC RECOVERY ID = OK CLEAR
8 xrudac 1 password - - - -
-xanavi>xrudac 1 password
unit id FLASH = OK READ [F100000001]
* Since the data in [ ] of UDAC SERIAL ID/UDAC RECOVERY ID is automatically created, it does not need to be confirmed. However, the same data must be displayed when checking the setting value in the next item.
9 xrudac 2 password - - - -
-xanavi>xrudac 2 password
UDAC SERIAL ID = OK READ [0x3FA62F5F]
10 xrsn 1 0x46310000
nnnnnnnn (chassis ID last
8 digits)
ymmdd (production
date)
password -
-xanavi>xrsn 1 0x46310000 00000001 70905 password
SERIAL NO. = OK WRITE [F10000000170905]
11 xrsn 2 - - - - - - xanavi>xrsn 2
SERIAL NO. = OK READ [F10000000170905]
12 xrfpn 1 1 0x******** 0x******** 0x******** 0x******** password registering EDAN xanavi>xrfpn 1 1 0x38413554 0x2d313943 0x3135362d 0x41470000 password
OK WRITE[8A5T-19C156-AG]
(US)
13 xrfpn 1 2 0x******** 0x******** 0x******** 0x******** password registering ECAN xanavi>xrfpn 1 2 0x394c3354 0x2d313444 0x3635332d 0x41430000 password
OK WRITE[9L3T-14D653-AC]
(JAPAN) 14 xrfpn 1 3 0x******** 0x******** 0x******** 0x******** password registering
VMSPN
xanavi>xrfpn 1 3 0x394c3354 0x2d313444 0x3635352d 0x41440000 password
OK WRITE[9L3T-14D655-AD]
15 xrfpn 3 password - - - - - fix data xanavi>xrfpn 3 password
OK COMMIT
16 xrfpn 2 1 password - - - - check EDAN xanavi>xrfpn 2 1 password
OK READ[8A5T-19C156-AG]
(US)
17 xrfpn 2 2 password - - - - check ECAN xanavi>xrfpn 2 2 password
OK READ[9L3T-14D653-AC]
(JAPAN)
18 xrfpn 2 3 password - - - - check VMSPN xanavi>xrfpn 2 3 password
OK READ[9L3T-14D655-AD]
19 xrfpn 2 4 password - - - - check ILCPN xanavi>xrfpn 2 4 password
OK READ[9C3T-14C165-AA] -
Category parameter
3 parameter
2 parameter
command 1 parameter
6 parameter
5 parameter No. 4
Parameter 2 should ba same as the one used in No.4
Application
Registering chassis ID
Registering UDAC
Delete UDAC recovery ID
Registering UDAC
Confirm registered UDAC
XTP log output example Command description
parameter 7
Registering ECAN/EDAN/VMSPN
Registering, fixing, checking customer part number.
In paremeter 2, 1=[EDAN], 2=[ECAN], 3=[VMSPN], 4=[ILCPN]
For part numbers to be input, refer to the part number instruction sheet.
1[EDAN] to be fixed after fixing Ford part number.
4[ILCPN] is for Brick only and needs to be done by 'DET' tool in advance.
After setting data, wait 1 sec. or more to re-check the data.
Registering Xanavi chassis serial#
Connect ACM to the system
Turn +B and ACC on, [cntl C] makes memory chack stop
Delete chassis ID
Registering chassis ID
Confirm registered chassis ID
Delete UDAC serial ID
Check Xanavi chassis serial#.
Xanavi confidential
Ford part number or other ID setting - Continued
Center Stack Brick
Making label 20 xtp 900 64 - Display Sirius ID [AUDIO][DATA] Sirius ID [AUDIO][DATA] to be correspond to serial#.
To make Sirius ID [AUDIO] barcode
Reading DVD mechanism license
key
21 xtp 700 69 - Displayiong DVD mechanism license key DVE mechanism license key to be correspond to serial#.
22 xrcnf 1 password - Setting configuration [DE00-DE09] -
audio 12 - - Audio command After audio command is input, Send Data Set -> must appear.
Audio microprocessor reset command
After audio microprocessor rest command is input, the xanavi> prompt must appear, and after the xanavi> prompt is displayed, at least one second wait time must be allowed.
24 xrcnf 2 - - Check configuration [DE00-DE09] Refer to the output example.
configuration table = OK READ
### HMI_Config[DE00] 0d 00 00 84 00 00
### 00
### HMI_Config[DE01] 06 0a 02 12 00 ff
### HMI_Config[DE02] 14 01 00 00 00 ff
### HMI_Config[DE03] 00 00
### 25 01 00 00 00 ff
### 0c 01 ff ec 00 ff
### 20 01 00 00 00 ff
### 06 01 00 00 00 ff
### 2d 01 00 00 00 ff
### HMI_Config[DE04] ff
### HMI_Config[DE05] 00
### HMI_Config[DE06] 00 0a 02 12 00 ff
### 07 0a 02 12 00 ff
### 2f 0a 02 12 00 ff
### 57 0a 02 12 00 ff
### 5b 0a 02 12 00 ff
### 76 0a 02 12 00 ff
### HMI_Config[DE07] 00 14 22 56 00 fe
### 0a 14 22 56 00 fe
### 33 14 22 56 00 fe
### 35 14 22 56 00 fe
### 5c 14 22 56 00 fe
### 64 14 22 56 00 fe
### HMI_Config[DE08] 00 14 22 56 00 fe
### 0a 14 22 56 00 fe
### HMI_Config[DE09] b8 01 00 00 00 ff
### b8 01 00 00 00 ff
### EQ Configuration Part Number LOAD
### Part Number 9L3T-14D660-AA
### EQ Configuration Part Number HDD
### Part Number 9L3T-14D660-AA
### EQ Configuration Part Number LOAD LAST
### Part Number
### EQ Configuration Number ff [LOADED]
### Splash Configuration Number 00 [LOADED]
end
---### EQ Configuration Part Number LOAD
### Part Number 9L3T-14D660-AA If "9L3T-14D660-AA" is different, refer to the AUDIO Circuit Board Drawing.
Deletion of user data,
25 dusa - - - Delete user data (initialization). CLEAR OK must appear.
0x70_0x18_0x00_0x00_0x00
Confirmation XTP log output example
Application
xanavi>xtp 900 64
(900) AV TEST START...
SAT RADIO ID
Sirius Audio ESN = [018287412012]
Sirius Data ESN = [018287312065]
...END(AV ) xanavi>xtp 700 69
(700) CD-ROM TEST START...
DVD MECHA DEVICE SERIAL No. = 02528 07203 00000 00000 ...END(CD-ROM ) parameter
2
Parameter 3 and after
Configuration setting/confirmation
xrcnf 1 password
configuration table = >> splash screen update start.[HDD to FLASH].
boot loading.
file read(C:\B1U\SKIN\SPLASH\TYPE1\FORD.SPL) size[784996].
read completed.
now checking read splash data.
OK WRITE
xanavi>dusa xanavi>
********** Memory Check Cancel **********
xanavi>>>User setting data initialization.
--- delete directory ---.
[E:\USER]
23
xanavi>audio 12
Send Data Set ->0x70 0x18 0x00 0x00 0x00
xanavi>
Command description Category No. command parameter
1