Chapter 3: Using the LCD Configuration Menu
IP5000 Bluetooth Support
The IP5000 can be equipped with a Bluetooth module allowing use of a headset that supports Bluetooth connections in place of a wired headset, see “Bluetooth Module Installation” on page 2-5 details. Prior to using a Bluetooth headset, it must be paired and can then be connected with the Bluetooth module. This section describes how to pair, connect, disconnect and delete a Bluetooth headset. Note that the Bluetooth menu is only available when a Bluetooth module is installed in the IP phone
NOTE: An asterisk, ], displays in front of the current headset selection.
When the Bluetooth module is installed, the icon is displayed in upper part of the IP8830 or IP8840 LCD. When one or more, maximum five (5), Bluetooth headsets are paired, the icon is displayed and, when connected, the icon is displayed.
When a Bluetooth headset is connected, a wired headset cannot be used and the Headset button will control the Bluetooth headset.
Pairing a Bluetooth headset
A Bluetooth headset must be paired with the Bluetooth module before it can be connected (activated). Up to five (5) headsets may be paired with the IP Phone at one time.
To Pair and connect a new headset with the IP Phone:
• Press the Settings ( ) button.
• Press the digit, or move the cursor to 3.Phone Settings using the
[Next]-[Previous] softkeys, and press the [OK] softkey.
• Press the digits, or move the cursor to 11.Bluetooth using the
[Next]-[Previous] softkeys, and press the [OK] softkey. • Press the digit, or move the cursor to
1.Headset Management using the [Next]-[Previous] softkeys, and press the [OK] softkey. This will display a list of previously paired headsets.
• If no headsets are paired with the IP Phone, press the [Search] softkey, the IP Phone will search for nearby Bluetooth headsets. If one or more Bluetooth headsets are already paired with the IP Phone, press the [ ] softkey and select the [Add] softkey to add another headset.
IP5000 Bluetooth Support 3-51 Chapter 3: Using the LCD Configuration Menu
• Select a Bluetooth headset from the list of headsets found using the
[Next]-[Previous] softkeys, and select the [Pair] softkey.
• When the "Enter PIN Code" is displayed, input the PIN associated with the headset and press [OK] softkey.
• Move to another parameter with the navigation buttons and continue the session or press the Settings ( ) button to exit the configuration session.
NOTE: If the PIN entered is valid, the Bluetooth headset is paired and automatically connected to the IP
Phone.
Connect or Disconnect a Paired Headset
When one or more headsets are paired with the IP8830 or IP8840 phone, the headset must be connected prior to use. When it is desired to change the active headset, the presently active headset must be disconnected prior to connecting the new headset. The following procedure describes the steps required to connect or disconnect a headset that is paired to the IP Phone.
To connect a headset that is already paired or disconnect an active headset:
• Press the Settings ( ) button.
• Press the digit, or move the cursor to 3.Phone Settings using the
[Next]-[Previous] softkeys, and press the [OK] softkey.
• Press the digits, or move the cursor to 11.Bluetooth using the
[Next]-[Previous] softkeys, and press the [OK] softkey. • Press the digit, or move the cursor to
1.Headset Management using the
[Next]-[Previous] softkeys, and press the [OK] softkey. This displays a list of previously paired headsets.
• Select a Bluetooth headset from the list of
IP5000 Bluetooth Support 3-52 Chapter 3: Using the LCD Configuration Menu
• Press the [Connect] softkey to activate the previously paired headset or press the [Discon] to deactivate the headset.
• Move to another parameter with the navigation buttons and continue the session or press the Settings ( ) button to exit the configuration session. NOTE: An asterisk, ], displays in front of the current
headset selection.
Deleting a Headset from the Paired List
A Bluetooth headset can be removed from the Paired list.
To remove a headset from the Paired list:
• Press the Settings ( ) button.
• Press the digit, or move the cursor to 3.Phone Settings using the
[Next]-[Previous] softkeys, and press the [OK] softkey.
• Press the digits, or move the cursor to 10.Bluetooth using the
[Next]-[Previous] softkeys, and press the [OK] softkey. • Press the digit, or move the cursor to
1.Headset Management using the
[Next]-[Previous] softkeys, and press the [OK] softkey. This will display a list of previously paired headsets.
• Select a Bluetooth headset from the list of
headsets found using the [Next]-[Previous] softkeys. • Press the [Delete] softkey to remove the
headset from the Paired list
• Move to another parameter with the navigation buttons and continue the session or press the Settings ( ) button to exit the configuration session.
NOTE: A Bluetooth headset must be disconnected as described in “Connect or Disconnect a Paired
Language 3-53 Chapter 3: Using the LCD Configuration Menu
Bluetooth Module Information
To assure the operation of the Bluetooth module, the address information for the module can be viewed from the Bluetooth menu item.
To view the active headset information:
• Press the Settings ( ) button.
• Press the digit, or move cursor to 3.Phone Settings using the [Next]-[Previous]
softkeys, and press the [OK] softkey.
• Press the digits, or move cursor to 11.Bluetooth using the [Next]-[Previous]
softkeys, and press the [OK] softkey. • Press the digit, or move cursor to
2.Local Device Info using the
[Next]-[Previous] softkeys, and press the [OK] softkey.
• Move to another parameter with the navigation buttons and continue the
session or press the Settings ( ) button to exit the configuration session.
Language
The IP Phone firmware includes an xml file, which, among other things, determines the languages available to the phone. When the xml file contains more than one (1) language, the Language parameter will be available.
To select an available language:
• Press the Settings ( ) button.
• Press the digit, or move cursor to 3.Phone Settings using the [Next]-[Previous]
softkeys, and press the [OK] softkey.
• Press the digits, or move cursor to 12.Language using the [Next]-[Previous]
softkeys, and press the [OK] softkey. • Select a Language from the list using the
[Next]-[Previous] softkeys, and press the [OK] softkey.
• Move to another parameter with the navigation buttons and continue the session or press the Settings ( ) button to exit the configuration session.